Unable to connect via cable or wireless to my WRT54GS

Similar Questions

• Satellite L350 - unable to connect via a WLAN

  Hello
  New to this lark of thread

  You just bought a L350
  I have managed to connect to the Internet via a cable, but am unable to connect via wifi.
  WiFi is turned on. He finds my BT Home Hub but when I connect, it just says: it's impossible.

  Help, please

  Have you checked the Wifi device in Device Manager? The driver is properly installed?

  Try turning off your firewall, which could block the Wifi connection.

  Also try to press Fn + F9 to toggle wireless devices

• Re: Satellite L300D - unable to connect via WiFi network

  Any help please? -I just L300D with Vista professional.
  Crossed troubleshooting but still unable to connect via the wireless network - no probs with other laptops.

  When going through "Toshiba assist" message arrives "this wireless network device is disabled.

  Please activate the device"- button wireless is activated with light yellow?

  any ideas?

  Are you sure that the laptop wireless switch is on?
  Look in the Device Manager. Maybe it's the wireless network card disabled. So activate it.

  Also try an update of the WLAN driver. You can find it on the Toshiba site:
  http://forums.computers.Toshiba-Europe.com

• Printer Hp6700: unable to connect to the router wireless D - Link DI-514 when SSID Broadcast is set to no.

  HP6700 printer: unable to connect to the router wireless D - Link DI-514 when the router Broadcast SSID is set to no. My MAC laptop and HP laptop both work with the set SSID on no. If I change the router Wireless SSID Broadcast is YES, then the printer HP6700 can connect to the wireless router. I set up the printer it saying that the SSID and password have been, the same as both of my laptops, but it connects ever, unless I have change the router to broadcast the SSID. Help!

  Have you tried to update the firmware on the DI-514?

  You can also try to set a static IP address on the printer, and then assign the printer to the list of DHCP static in the interface of the router.
  To give a static IP address to your printer:
  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') 250
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway.
  -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS. It's Google DNS. You can choose a different external DNS if you wish.
  -Click 'apply '.
  Now, stop the router and printer, start the router, wait, and then start printing.

  After that you remove and re - add the printer to your Mac.

  Show support by clicking on the blue Kudos star in the post that solved your problem. Doing so will help the other members of the forum their solutions also.

• Internet Explorer message: "unable to connect via the parameter to wide band".

  When I try to connect to Internet Explorer, I get a message saying unable to connect via the parameter to broadband. We have AT & T Wi - Fi that I seem to be the only one of 4 people in our House, that has a connection problem. We all have different types of computers, some run Windows 7 and others are Vista. Don't no if this material. I preformed a few tests without results of troubleshooting. Help, please

  [Original title: programs network networking Internet site Internet website URL website network]

  Hello

  ·         What is the exact error message you get when connecting to internet?

  ·         Which is the browser you use to access the internet?

  ·         You are able to use other internet applications such as messenger etc?

  I suggest you follow the steps below:

  Method 1:

  Follow the steps in the link below to connect to the internet in the link below:

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Method 2:

  Follow the steps outlined in the article below if you can not connect to internet:

  http://support.Microsoft.com/kb/956196

  Method 3:

  If the steps above do not follow the steps in the link below for network connection problems in windows:

  http://Windows.Microsoft.com/en-us/Windows/help/network-connection-problems-in-Windows

  I hope this helps.

• Unable to connect via the wireless router "problem with wireless adapter or access point" _

  Hello

  I recently replaced my old Toshiba laptop with a new model of Toshiba Satellite L500/033HNX, it installed Windows 7.

  The problem is that I can't connect to my wireless network. I am currently connected via Ethernet cable to my Linksys router.

  I had help from my internet service provider, the installation correctly the problem not because of the connection.

  I had a Linksys online support, the router is a wireless, model - WAG54G ADSL gateway, is not the problem of all the correct settings and other devices can connect via my wireless network. I ran Dr. connectivity several times and it is always impossible to connect, "problem with the wireless adapter or access point.

  OK, you're my next hope to solve the problem can you HELP Please!

  Hi, JoelbX
  I want to thank very you much for your support and effort do to help me solve this problem, but we receive have been, and I don't want to waste any more of your valuable time, so I am the son of closing and deleting of Tring in Microsoft Answers.
  All the best
  Tring

• Equium L40 - unable to connect via wifi or cable plugged ubs

  Hello

  I have an Equium L40. I can not connect via wifi or cable plugged ubs.
  It is a "Internet Explorer has stopped working. a problem caused the blocking of the program works correctly.

  He said in am connected to my hub and have a signal strong.

  Can you help me

  Thank you

  Steve

  Hello Steve

  Have you tried using another browser?
  Using Skype or some other messenger? None of them can connect properly?

  I put t know what is the real problem. Work not Internet Explore or WLAN connection in general?

• Unable to connect via wireless with SSID broadcast disabled

  I want to configure my router for my SSID is not broadcast, because I think it's a logical step to take for increased security. I have not been able to do since I started using my new laptop Inspiron 5558. I tried this several times and every time I turn off the SSID broadcast, I am not able to connect to the Wi - Fi on this laptop. Other remote computers in my house and my smartphone connect without problem, but nothing I've tried helps my new computer Dell laptop to connect via Wi - Fi, except for allowing the SSID broadcast.

  I have a router Actiontec MI424WR reverend E. I have installed the new driver and the Intel PROset utility and unfortunately nothing has changed. I went to the settings to investigate some of the other solutions offers, and I came across something that seems to have solved my problem. What I found in SETTINGS/network & Internet/change adapter options/Wi-Fi/see the status of my properties of connection/Wireless / on the connection tab, it was an uncontrolled area with the words "connect even if the network is not broadcasting its name (SSID). I checked this box, and since then, I was able to connect to my network wireless with SSID broadcast disabled. I will now call this resolved and if no new problems arise. start a new post. Thanks for sticking with me on this.

  Ed J.

• Unable to connect via wireless

  Hello

  I use a HP Pro book Windows7 professional. All systems were functioning well when the wireless connection has been disconnected.
  Later my laptop cannot connect via wireless even if system the wireless still work correctly on my ipad.
  Please tell us what I should try to fix this problem.

  You have run the wireless troubleshooting tool? - http://windows.microsoft.com/en-US/windows7/Using-the-Network-troubleshooter-in-Windows-7

  Is your wireless network of the specified interface as active or disabled, if disabled then re-enable-control panel, network and sharing Center, change the settings of the map, right click on your device to turn on or off (you will be asked for admin at some point).

  PS - extra thought, some laptops have a wireless switch network. It is not struck off there?

• I am unable to connect to my router wirelessly to parents. I tried to reset the modem and the router and it still does not work.

  Presented labtop parents and can connect via ethernet, but still cannot connect to the wireless router. Ive rebooted both the modem and the router and ive also unplugged the power source. Help, please...

  original title: unable to connect to the wireless router?

  Hi Brandon,.

  What operating system do you use? (Windows 7, Vista, XP?)
  You receive any type of error message when you try to connect?
  What exactly happens when you try to connect?
  You receive an internet connection when you connect with an Ethernet cable?
  There are a few good troubleshooting in this thread. I suggest to look to see if it helps at all:
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/unable-to-connect-to-a-wireless-network-Windows-7/734ecdef-99fb-4862-b63a-04cfa448cc06

• Unable to connect via radio - impossible to obtain network address

  All,

  I had to restore this laptop due to virus problems (my daughter system..).  I have put back it and it works except that I am unable to connect to the wireless network.  It says 'Acquiring Network Address' and goes then to the "Limited or no connectivity."

  Here are the details:

  System:

  Inspiron 1300 - XP Pro SP2

  Dell Wireless 1370 WLAN Mini-PCI Card

  Parameters:

  o use Windows to configure the verified wireless network

  o in Dell Wireless Utility, unchecked "let this tool manage your network."

  o WZC: start & automatic

  o TCP/IP: Obtain IP automatically and obtain DNS automatically

  I took action:

  o reloaded all drivers available for my service tag, including the pilot for

  the network card

  o went through all the Dell relevant troubleshooting steps

  o I have a different laptop that connects to the wireless network and I

  compared the parameters between the systems of work and non-working - they

  seem to be the same (another pc and card)

  o the 'bad' system can connect to the network via ethernet cable

  The status bar displays the network icon (pc screen) with yellow trinangle and!

  and 5 green bars for the network card has an excellent signal with unknown status.

  I'm not clear on the question of whether Windows or the utility of the card should be network management; I tried both to no avail.  I'm basically out of options to try and hoping someone can help me.

  Please let me know if there are any additional necessary information.

  Thank you in advance for your help!

  
  

• Unable to connect via wifi Web after that windows update 8.1

  Laptop HP Pavilion 15 pc 15 n032sa-update to windows 8.1 but now unable to connect to Internet with wifi I have to use the yellow cable.

  Hello

  Please try

  (a) go into Device Manager and uninstall the network card (NIC) wireless.

  (b) restart the machine.

  (c) wait 10 mins.

  Or click on the following link and click Search now

  Kind regards.

• To connect via PPPoE (dialer) Wireless ADSL

  Hello

  I have a WAG200G Annex-A Wireless G modem router ADSL residential, I used as a wireless router. Now I've changed suppliers (Auntie Indicom - in India), and they have a 'new technology '. Basically, instead of giving me a DSL line in my house, now they directly give me an Ethernet cable in my house (they have a local DSL box somewhere on the roof with various Cisco switches for each household). Then, they want to connect via PPPoE by starting a Dialer on my computer, this particular Ethernet cable is connected.

  Now, that works all very well, but we have more than one computer at home, and I would like to use Wifi instead of being connected at all times via the cable on my laptop.

  So now my question is:

  Can I configure the Linksys router so that IT don't the PPPoE dial for me? Basically this means plug the Ethernet cable provided by my ISP in one of the ETHERNET Ports and set up allowing to switch on (since there is no cable "line" adsl connected more) with my user name and password.

  Anyone know how to do this, or if this is possible?

  Thank you!

  P.s.: I've set up the Internet connection sharing via ad-hoc wireless, which works very well, but is only a temporary solution because I don't want to use my laptop as a router...

  It is not possible to configure WAG200G without ADSL line.

• Unable to connect via nfs, ftp only

  My network has two devices NAs - a NetGear ReadyNAS 102 (2x1To) and an OXFORD (NAs French device, 1x500GB). I'm trying to set up a weekly backup of critical files to the ReadyNAS to the GLOBAL system.

  On the OXFORD ring road, I activated CIFS, NFS and FTP. Using FTP, I am able to connect to the NAS without problems. However, I couldn't finish a single backup via FTP. The last attempt continued for 3 days and then failed. When I try to connect to the same part of the OXFORD box by using nfs, I get the error "unable to connect to the host.

  Are there steps I can perform to solve this problem?

  Thank you

  bsmerbeck wrote:

  I think that we could be closer to our cause of errors. I tried this command and received this error message:

  "showmount: failed to get address for.

  Maybe try this variant:

  showmount e 127.0.0.1

• HFG30 unable to connect via the Android app

  Nexus 7, HFG30 - all online and printed documentation confusing. Is not clearly the distinction between applications and the use of the web browser. Nowhere is the name of this app is mentioned. Had to go back with support to find the name.

  The name of the application's access to the camera more than, unfortunately, the Pixels.

  HFG30 not in the taken list supported here. Support says that it is supported. After all, no connection. Can connect via a browser however. Anyone else?

  Hi robbif!

  Thanks for posting.

  The application CameraAccess and CameraAccess Plus is not for all our camcorders.  Some newer models, like the G30 HF, are controlled using a web browser based remote connection, instead of using the application.  For more information about this, visit our help wireless page or view the distance travel brochure HERE.

  If it is a time sensitive matter, additional support options are available to contact us.