Unable to defragment the local disk c

Similar Questions

• Unable to defragment the Local C drive

  Whenever I have try to defragment my hard drive, he said "Disk Defragmenter has detected that Chkdsk is scheduled to run on the volume: (C). Please run Chkdsk /f.»

  F is a removable drive on my computer. What should I do to get it to defragment the volume C?

  Go to http://technet.microsoft.com/en-us/sysinternals/bb963902.aspx and download, install and run Autoruns.  Click the scheduled tasks.  Uncheck entries to run chkdsk (there may be more than one entry).  Then restart.  The start task, you should be able to defragment.  If you can't find there, you can click the all and check all entries to have anything to do with chkdsk and clear the checkbox to remove the starter.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Problems downloading a file of muse for the first time. Museutils.js is not on the local disk on the file index.html.

  Hi all

  I hope someone can help because I'm a little desperate.

  I started to design a page with a muse of Qooqee model: SENSE.

  I worked for a month on this issue. When I was about to finish, I got a message that there is a new version of Muse to update. I did the update when I was still working in the design.

  When I finished the desktop version, I downloaded using the "upload to the ftp host" button. All fine until he has gave a "error on the index.html file.

  

  So, I was unable to complete the first uploaded to the online page.

  My husband, who knows a bit about coding, opened the index.html file, and we have seen a warning: MUSEUTILS. JS IS NOT ON THE LOCAL DISK.

  

  Reading questions similar to the forum that I can guess that the problem has been built with I started with the earlier version of the Muse and updated the Muse version in the workplace, when I finished the page.

  Now, the page is not alive because I am not able to download the file.

  I don't know if that's the problem, however. I downloaded a fresh sense of QooQee model and erase all content and pages name I will use them (he has added a few pages and I moved the contact page somewhere else on the site map). Then, publish the page Go Daddy and have the same problem. Error on the index.html file. For that I am lost again, because everything has been done with the same version of Muse and the latest model of sense (I don't know how they update the models).

  Can you please give an idea on how to solve the problem? What I have to redo the entire page?

  Thanks in advance, you are my last hope.

  Good to see that we can exclude a Muse for the functioning and the collection of production. The problem must lie in the specifics and/or requirements of GoDaddy, hosting provider. The Muse team is very aware of being a very popular hosting provider GoDaddy , so they want to learn all the occasional problems or quirks that might appear with Muse in combination with these suppliers. It might have to do with the current version of Muse, but it could also be a coincidence that GoDaddy has begun to change some things on their side as well. Or it could even be a Gremlin (colloquial term for a software bug temporary and inexplicable) blocking a circuit which seems to happen from time to time...

  Are you sure that you follow all the advice and guidelines in this FAQ: download an Adobe Muse of the site to a third-party hosting service ?

  Hang on!

• all my data is all save on the local disk c, how to share the data with the other drive, local drive d.

  all my data records on the local disk c, how to share the data with the other drive, local drive d.

  Hi Jasonbichard,

  1. what type of drive is D? Is - this another partition on the same disk?

  2 Windows operating system you are using?

  You can change the location of the disk to save the data in the d: instead of C: and check if it helps.

  a. navigate to the location (username) C:\Users\.
  b. right click on the folder that you want to change the location, and then select Properties.
  c. click on the location tab and change the location to D: drive.

  d. click on apply and Ok.

• I'm not able to merge the partition not used to the local disk partition

  I'm using windows xp service pack 3 and I have deleted my partitions from disk 2, but im not able to merge the partition not used to the local disk partition, what should I do?

   
  Original title: HELP ASAP!

  Hi Joseph.

  Suggestion of PML in the thread below, can be very useful.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-performance/how-do-i-merge-two-partitions-in-XP/d2a7fa28-b2dc-41F6-9cd3-2c2beb6c6865

• Remove temporary files from the local disk c/documents and settings/user/localsettings/temp name

  Remove temporary files from the local disk c/documents and settings/user/localsettings/temp name

  By definition, this folder should contain only the elements you don't need.  If I understand correctly, this temporary folder is a place where temporary files are stored during program facilities and the facilities.  However, I have seen references other sites to help saying some programs can store folders and files.

  I do my own temporary file elsewhere, name it accordingly and move all the files in the temp folder to the new folder. Use your computer normally for a while, and if nothing complains about missing files, you have a good indication that none of the moved files are important and should be safe to delete.

• User duplicated on the Local disk folder

  Hello

  I was looking through the C: drive and found two user folders.  I went to the location of the folder of each and both were located on the Local disk and both had the same files folders and dates:

  Intel
  PerfLogs
  Program Files
  SwSetup
  Users
  WINDOWS

  I don't remember ever having seen two user folders.  Is it a normal thing?

  Thank you!

  M

  Hello

  1. how many accounts user are there on your computer?

  2. have you created a new user account?

  The files you mentioned are the same for all users.

  Please post the screenshot of the users folder that would help us helping you better.

  See the link.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-security/how-do-i-post-a-screen-shot-on-this-forum/c86de820-C620-401c-A804-9f6337cd3053

  I also suggest you to download and run the latest Microsoft Scanner on your computer and check to see if it helps:

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: the data files that are infected must be cleaned only by removing the file completely, which means there is a risk of data loss.

• Change sharing permissions, now I can't access the local disk

  Hello all, I have two computers, both running windows 7 (one is 64-bit and the other is 32-bit) connected via LAN and WiFi. One of them has all of the local disk shared with full compensation for everyone (full control). I decided to remove these permissions and control to "deny". Then I had to cancel the task and decided to resume later. HURT, now I've lost access to this drive, even though I can access some files. When I try to enter in the drive, an error message appears saying "C: is not accessible. Access is denied. I did some research and it seems to be a common problem, but I followed all the steps did not work. It shows as 0 bytes and security options does not show anything, but "you don't have permission to view or change the permissions of the object settings. I tried to adapt, even in safe mode and as administrator, do not to prevail. It keeps saying 'access denied' I also tried to set a hidden administrator account, but the account manager is 'not available for my system' when I made these unfortunate changes, it was not this computer but on the other, I think it might be the reason. Now, I can not access my local disk or change anything. Please, help me, I can't find a solution to this mess!
  Thank you

  Hello

  I suggest you to follow the steps in the link given below and check if it helps.

  How to open a file if I get an access denied message?

  http://Windows.Microsoft.com/en-CA/Windows7/how-do-i-open-a-file-if-i-get-an-access-denied-message

  Let us know the status of the issue.

• Access denied to the local disk (D)

  Hello
  I have a problem with windows 7. In fact, I changed the permissions on the local drive (D) to "total control has declined. I tried to go back to the 'authorized' by following the tutorial posted on your support site, but I am facing a tiring situation, since I have to repeat the process (right click--> Properties/Security /...) for each subfolder and the thousands of files in the folder. Is there a solution to this problem? If I install a new system that will overcome the problem?
  Please help me I'm stuck!

  I changed the permissions on the local disk (D) "total control has declined.

  Why would you do that?

  You will need to take ownership of files to repair the damage - see here:
  http://TechNet.Microsoft.com/en-us/library/cc753659.aspx

• remote VPN and vpn site to site vpn remote users unable to access the local network

  As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config

  The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.

  ASA Version 8.2 (2)
  !
  host name
  domain kunchevrolet
  activate r8xwsBuKsSP7kABz encrypted password
  r8xwsBuKsSP7kABz encrypted passwd
  names of
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  PPPoE client vpdn group dataone
  IP address pppoe
  !
  interface Ethernet0/1
  nameif inside
  security-level 50
  IP 192.168.215.2 255.255.255.0
  !
  interface Ethernet0/2
  nameif Internet
  security-level 0
  IP address dhcp setroute
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  management only
  !
  passive FTP mode
  clock timezone IST 5 30
  DNS server-group DefaultDNS
  domain kunchevrolet
  permit same-security-traffic intra-interface
  object-group network GM-DC-VPN-Gateway
  object-group, net-LAN
  access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
  tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  MTU 1500 Internet
  IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
  ICMP unreachable rate-limit 1 burst-size 1
  enable ASDM history
  ARP timeout 14400
  NAT-control
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  AAA authentication LOCAL telnet console
  AAA authentication http LOCAL console
  AAA authentication enable LOCAL console
  LOCAL AAA authentication serial console
  Enable http server
  x.x.x.x 255.255.255.252 out http
  http 192.168.215.0 255.255.255.252 inside
  http 192.168.215.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto-map dynamic dynmap 65500 transform-set RIGHT
  card crypto 10 VPN ipsec-isakmp dynamic dynmap
  card crypto VPN outside interface
  card crypto 10 ASA-01 set peer 221.135.138.130
  card crypto 10 ASA - 01 the transform-set RIGHT value
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 65535
  preshared authentication
  the Encryption
  sha hash
  Group 2
  lifetime 28800
  Telnet 192.168.215.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 5
  Console timeout 0
  management-access inside
  VPDN group dataone request dialout pppoe
  VPDN group dataone localname bb4027654187_scdrid
  VPDN group dataone ppp authentication chap
  VPDN username bb4027654187_scdrid password * local store
  interface for identifying DHCP-client Internet customer
  dhcpd dns 218.248.255.141 218.248.245.1
  !
  dhcpd address 192.168.215.11 - 192.168.215.254 inside
  dhcpd allow inside
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  Des-sha1 encryption SSL
  WebVPN
  allow outside
  tunnel-group-list activate
  internal kun group policy
  kun group policy attributes
  VPN - connections 8
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value split tunnel
  kunchevrolet value by default-field
  test P4ttSyrm33SV8TYp encrypted password username
  username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
  username kunauto attributes
  Strategy Group-VPN-kun
  Protocol-tunnel-VPN IPSec
  tunnel-group vpngroup type remote access
  tunnel-group vpngroup General attributes
  address pool VPN_Users
  Group Policy - by default-kun
  tunnel-group vpngroup webvpn-attributes
  the vpngroup group alias activation
  vpngroup group tunnel ipsec-attributes
  pre-shared key *.
  type tunnel-group test remote access
  tunnel-group x.x.x.x type ipsec-l2l
  tunnel-group ipsec-attributes x.x.x.x
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  Review the ip options
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  call-home
  Profile of CiscoTAC-1
  no active account
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
  : end
  kunauto #.

  Hello

  Looking at the configuration, there is an access list this nat exemption: -.

  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0

  But it is not applied in the States of nat.

  Send the following command to the nat exemption to apply: -.

  NAT (inside) 0 access-list sheep

  Kind regards

  Dinesh Moudgil

  P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community

• I just installed DW 13.2.  Linked files (all CSS, scripts...) "are not on the local disk" - all works in CS6. Help..?

  I just installed DW 13.2.  Linked files (all CSS, scripts...) "are not on the local disk" - all works in CS6. Help...

  When I insert one of the page of the Web site, it shows in the design window.  But when I try to bring any document linked in the left window, code, it is empty and the message says: "whatever.css is not on the local drive.  Also, when I click on LIVE, the file looks like she does not see the file CSS, no images.

  The same site looks and works OK in the DW CS6.

  I'm on Maverick - 2012 Mac Pro - 2 x 2.66 12-core, 64 GB of RAM.

  I configured the same way as CS6 preferences.  Same location of the site, same links.

  Am I missing something?  What should I do?  I uninstalled the DW CC, cleaned pref and installed it again.  Same question.

  Help, please.

  I think, I solved the problem, but I still think that the Dreamweaver does not recognize the addresses.

  I then drive CC_A BB_A Web sites (these are the actual names of the readers).  It's always the disk 'data', apart from the OS, but with a different name.  everything works.  Opening files referred to in the script window, 'live' works as supposed.

  I can only speculate that readers 'CC_A' name has confused the program called CC.

  I can find no other explanation, since, in addition to the name of the drive - everything else is the same.

  Thanks for trying to help.

• VCenter 4.1 connect to iso image on the local disk

  Hello

  I have a question about certain permissions in vcenter 4.1 until now, we have used vcenter 4.0 and we had a few asigned security role with permisions them following: all privileges: Virtual Machine: Interaction: configure support CD; Configure floppy Media; Interaction of the console; Turn on; Power off; Reset.

  It is basically the minimum requirements for some of our clients to witch we sell vps servers.

  My problem is: given that I've updated vcenter 4.1 security to configure cd media does not seem work apropriately. The only option witch is not grayed out is connect to the host device. The possibility to connect to iso image on the local disk or connect to the physical drive D: (local client CD-ROM) are greyed out.

  Someone knows something about this security role change and what kind of extended privileges do I have to add in order to make it work?

  Hello

  I think you should also "connection device"...

  In addition, there may be one advanced virtual computer that denies this capability... Here are the parameters of the isolation and many guides say to turn it off.

  Best regards

  Edward L. Haletky

  Host communities, VMware vExpert,

  Author: VMware vSphere and Virtual Infrastructure Security,VMware ESX and ESXi in the 2nd business edition

  Podcast: the Podcast for security virtualization of resources: the virtual virtualization library

• Groups and permissions of the user is added to the local disk post-conversion?

  We currently have a security policy with our Windows servers requiring admins to remove unnecessary security groups and users on the local disks. Basically, the SYSTEM and administrators retain full control, but all other users and groups are deleted for security reasons. We find that during a P2V conversion/clone servers, security groups and users are added to the readers of these new virtual machines (see screenshots below):

  Security before and after conversion. Could this be a function of the sysprep post-conversion tasks that work?

  Until now, we thought that, apart from the usual physical changes inherent to a clone, security remains unchanged. We follow best practices for conversion of these machines (running this as a local administrator account, run this converter installed on the machine, by stopping services as much as possible and so on).

  You can compare it to a system where you don't resize volumes, but all other factors are the same?

  If you reduce the size of a hard disk volume during the conversion, it will make a copy of file by file from the source to the destination devices.  We may have to add permissions for the conversion process, but I don't know if it is real.

  If you maintain or increase the size of the hard drive, it is a clone of block level which should be a bit-by-bit copy the source system.

  Kind regards

  EvilOne

  VMware vExpert 2009

  NOTE: If your question or problem has been resolved, please mark this thread as answered and awarded points accordingly.

• Unable to create the virtual disk: fault. RestrictedVersion.summary

  Hello

  Im trying to create a virtual disk using the CLI on ESX4i.  The script is:

  vmkfstools.pl - Server 10.190.2.51 - c 20 g d eagerzeroedthick - a free /vmfs/volumes/Internal/test.vmdk

  When the script runs I get error: unable to create the virtual disk: fault. RestrictedVersion.summary

  Can someone tell me why please.  Im trying to create a disk of 20 GB with adapter free with eagerzeroedthick on my internal called storage, (no subdirectory).

  The file system is THAT VMFS 3.33 maximum file size is 256 GB.  The block size is 1 MB.  If it is the block size that is the problem how can I easily change?

  It's in a laboratory, not a production environment.  I need the flag eagerzeroedthick like Im trying to create a passive active cluster node MSCS 2 on a single physical node with 2 machines VMS.

  Thank you.

  Mike.

  If you use the free version of ESXi (U4 and later versions), access to tools like the VIMA API are read-only.

  -Matt

  VCP, vExpert, Unix Geek

• Edge code will not be installed, it keep asking to be installed on the local disk.

  I'm on Windows7 Home Premium, the Dungeon of the installer asks me to install on the local disk, which I am installing to the local drive C by default.

  

  Can anyone help? He comes to inspect the edge too

  Hi Nick,

  We had a few reports of this problem with the media as well.  You can try these workaround solutions and let us know how it goes?

  1. Make sure that you do not have other installers at the same time (see the "msiexec.exe" Task Manager)
  2. Make sure you have enough free hard disk space
  3. Restart your computer (installers are sometimes tricky if the installer from some other app ran earlier but is still saving a few tasks until the next reboot).
  4. Run the installer as admin, as follows:
     1. Click with the right button on the "Command Prompt" application and choose Run as administrator
     2. Use cd to navigate to the folder where you downloaded the .msi installation file
     3. Run the following: msiexec /i «2.msi Adobe Edge Code Preview»

  -Peter