Unable to push on another network multicast streams

Similar Questions

• Unable to connect to another network

  Greetings,

  I had already installed my deskjet 3520 and used wireless with no problems. Since then, I had changed my ISP and I bought a new modem and router with new SSID and password. Currently, I am facing problems connecting to my network again. Have tried all suggested ways for hours without result. Already reinstalled the software using the CD provided and tried to use the usb to connect from the path of the WPS does not work. He urged that it is impossible to connect the printer to the network coz of 3 reasons:

  (1) firewall - since disabled norton

  (2) router MAC activated - already disabled

  (3) different network

  Please help and see if you could get my printer to work again wireless. Thanks in advance for your efforts!

  After having tried to establish a connection between the printer and network for hours, I was finally able to operate using the WPS configuration. I tried to connect by holding button for 3 seconds the router WPS, but it still doesn't work. I does not come across any suggestion of HP I might need to ACTIVATE the WPS on my router configuration web page. Now I can connect wirelessly. Hope this help anyone else with similar problems like me and I thank you for your help also, sabretooth.

• Unable to connect to the network. Tried to install another LAN adapter but received the error no. 31.

  NETWORK CONNECTION

  I have a windows xp operating system. I am unable to get the network connection. I called the person of the ISP. He informed that there is no problem with the network cable and I should check my LAN card. I tried to install another network card, but he could not settle. Error No. 31 was flashed on the screen. PL. advice me how to rectify the problem.

  Hello

  We can refer to the following items and try the steps and check.

  Code 31: This device does not work properly because Windows cannot load the drivers required for this device

  Explanation of error codes generated by Device Manager in Windows XP Professional

  I would also recommend to update the chipset drivers. You can contact the manufacturer of the computer on the updates on this.

• network data stream

  Good afternoon

  I need to send the data generated in the vi, by network data stream.

  The problem is that I found no example that does something similar, and this is my first time using Activex with Labview. Can someone explain me how to send Activex data via the network stream please and if possible help me find a solution to the attached vi.

  I think I need to convert the data somehow after control of the room before using the writing and reading items, I tried with strings and arrays unsucessfully, I really think I'm missing something.

  Thank you in advance!

  Erika

  Erika,

  What do you think?  You try to play an .avi file, a .mpg or what?  IMAQdx has functions that can play video and output files 'images', and you can deliver these images via TCP/IP on another computer using network flow.  Indeed, there are cameras that capture video and output via TCP/IP - IMAQdx is used to capture the image directly from the camera and can view or save a file from .avi (for example).

  You have the Vision Module installed on your system?  In your Palette of block diagram, it will appear under the Vision and movement and should include IMAQ (or IMAQdx) and utilities of Vision (which contains the Palette under files to make the reads and writes of video files).  See if you can use this to display your video...

  Bob Schor

• Unable to connect to a network or to the Internet on my Dell XPS1530.

  Unable to connect to a network or to the Internet on my Dell XPS1530. When I try to diagnose problem, I get a message that reads "Network Diagnostics cannot run because the Diagnostics Policy Service is not running." Having exhausted the patience all the phone with my IP and Dell, which tells me that it is a problem of Microsoft software. I have two other computers and a PS3, and I am able to connect to the Internet through one any of them. The XPS works under Vista with SP2. Can someone help, please? Thank you.

  Go to start / Control Panel / Administrative Tools / Services and go to diagnostic policy Service and set it to automatic and start it.  If it does not start, check the dependencies and make sure they're too automatic and rnning.  Then see if you can run Network Diagnostics.

  You can get in trouble with your device drivers.  Go to Device Manager by going to start / find and type Device Manager and enter and then double-click on the program icon that appears.  Check each device to a red x, yellow! or white?  These identify devices with problems probably (drivers, but also of conflict or something else).  Click on each for more details and troubleshooting tips.  If you need to get drivers (and you should get those developed to date for the network card and regardless of the device you use to connect (such as a router wireless or such) and all you have time to do - they can help way beyond simply solve this problem), let the computer dealer or the manufacturer of the device (NOT of Microsoft Updates).  In fact, you must disable automatic updates in Windows Update driver as follows:http://www.addictivetips.com/windows-tips/how-to-disable-automatic-driver-installation-in-windows-vista/. Follow these steps to get the drivers: http://pcsupport.about.com/od/driverssupport/ht/driverdlmfgr.htm.  Once you have the drivers, you can install them via the Manager device as follows:http://www.vistax64.com/tutorials/193584-device-manager-install-driver.html.

  When I'm in a lke your situation, I usually start from scratch.  Create a new network connection by ensuring that all settings are correct.  Check all the cables (if there is).  You have already reinstalled the drivers - make sure that no firmware or software is also necessary.  Configure the network sharing settings and make sure that you are ready to discover the network and such.  Check other computers to see their settings to make sure you get yours right and essentially the same thing (the same exatly so is another Vista machine connected in the same way).  Go to start / Control Panel / Internet settings and make sure that it's too fixed properly.  To connect, then try again. If this is not the case, remove some time to cool down and then start again with another new connection.  It's almost certainly a parameter that is not correcct (something no doubt very simple).

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• I used a time capsule in my house.  Now, I have another network put in place and would like to set my time for back ups and NOT as a WiFi capsule

  I used a time capsule in my house.  Now, I have another network put in place and would like to set my time for back ups and NOT as a WiFi capsule

  If it is possible to turn off the WiFi on the Time Capsule, which only leaves you with the option to back up your Mac (s) using a wired Ethernet cable connection between the Mac (s) and the Time Capsule.

  Are you OK with that?

• I have IE8 Favorites saved off as bookmark.htm in another network location. How can I get in firefox?

  I have IE8 Favorites saved off as bookmark.htm in another network location. How can I get in firefox?

  Bookmarks > organize bookmarks-> import and backup - import HTML... = HTML file

• Unable to connect to wireless networking

  My Toshiba laptop has been pre-installed with Windows 7 Home premium 64 - bit OS and it worked quite well with the BB wireless. However, the wireless internet was on and turned off in recent weeks, while other mobile devices, such as iphone, ipad, or laptop, in my household had no such problem. The wireless signal was so strong, but the error message always says "unable to connect to wireless networking. It seemed that there was something wrong with the wireless adapter.

  I got a new adapter properly installed TP-Link wireless. Fortunately, it worked; but unfortunately, it worked for less than 24 hours. It was really frustrating that I, like student full time, depended so much on the wireless network card.

  Help, please! Harry

  Hello

  You can enlighten us with:

  -What model do you use (eg..) L300-123)
  -What version of BIOS is installed?
  -WLAN driver do you use?

  All these questions are answered in PC Diagnostics are under Toshiba app folder in the start menu.

  BR

  Tom

• I'm trying to update my ipad (first edition) to the new version and after about an hour, I get a message that says unable to finish because the network has expired.

  I'm trying to update my ipad (first edition) to the new version and after about an hour, I get a message that says unable to finish because the network has expired.  How can I fix it?

  Original title: network programs network networking Internet Web site Site Web Web Site URL

  Hello

  You need to support iPad not Microsoft.

  iPad - media choices
  http://www.Apple.com/support/

  iPad - Support
  http://www.Apple.com/support/iPad/

  iPad - communities (Forums)
  https://discussions.Apple.com/index.jspa

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• another network with my Ip address?

  A message appeared saying: "another network has the same IP as this PC, I checked the network administrator and conducted an audit and found no problems.

  I also checked for antivirus updates and no problems were found. I recently signed up for Yahoo. This has something to do with the IP address?

  Hello Silvia,.

  I don't see how to sign up for Yahoo this would cause.  Although this is stated in the reference below, it is IMPOSSIBLE to have two identical IP addresses on the internet.  There are sometimes common sense as well as the technical reasons for this. You can read or skip to the next section you choose covering some basic concepts of networking that can help as I don't know where you are in terms of networking knowledge. This could be much too basic or even above your head.  The answer to your question follows this section with an article that will probably the thing and then a search for related sites that cover this problem if this article isn't enough.

  ******************************************************************

  It is a phenomenon of local network because all local networks use one of three ranges for the allocation of addresses TCP/IP based on the number of computers should be connected.  For home use, it is usually begins with 192.168. and two other numbers that are limited by a set of rules.  Most people use 192.168.000.001 (or which is written 192.168.0.1 as address of the router (or gateway) and the local DHCP server, Server DNS and WINS Server (often assigned and controlled by the router, but sometimes by a computer instead for various reasons).  Then network (DHCP server) Configuration is used to assign a range of acceptable numbers for computers that use this number.

  Most people allow these numbers are dymically assigned by the DHCP server to keep things simple - so that a specific computer may change from time to time.  Some devices need an assigned static address (which is reserved for this device which always uses and nothing else is never assigned it on this network because two that are the same on the same network would have caused a problem such that the communication would not have an idea that you choose if selected).  An example might be a stand-alone network printer where the configuration of the printer on any computer using it could be a nightmare if not to change the address of the printer and that nobody was able to connect to it - then it becomes static and then all computers use this address and since it never changes which avoids printer problems.  Another example is the above router other than the same problems occur whenever the computers tried to connect to the internet or connect to what be it through the router.

  Now, if you have two LANs linked together, a problem starts to appear as both may have been implemented with the same philosophy and therefore likely to use the same numbers.  This is often done using a network http://www.ehow.com/how_5329107_use-router-bridge-two-networks.html bridge or can be done through complex subnets creation of each network (more complicated).

  For the more (and perhaps even to understand that, you need to understand the basics of networks.)  Here's a search to find some one who can help you get started: http://www.bing.com/search?q=networking%20basics%20tutorial&PQ=Networking%20basics%20&SP=2&QS=AS&SK=AS1&sc=16-26&form=BSRTSS&pc=BBSR.

  *******************************************************************

  Please see http://answers.microsoft.com/en-us/windows/forum/windows_other-networking/another-computor-is-using-same-ip-adress-as-my/84f10eec-9ff4-4d40-8867-392422367026 which should help explain some things about it (and even if in a forum of Vista, most if not all of it applies to networks in general - so don't worry that).

  Learn more (a lot more, actually) on both computers with the same ip address, see the following Bing search which will give you plenty of resources for this, why and how it happens and what to do when it comes to solving things: http://www.bing.com/search?q=two%20computers%20with%20same%20ip%20address&PQ=two%20computes%20with%20&SP=1&QS=SC&SK=&sc=16-34&form=BSRTSS&pc=BBSR.

  I hope this helps.

  Good luck!

  Kosh

• Unable to read the security descriptors data stream

  Whenever I start my computer runs CHKDSK - it says checking file system on E: and then he said that it should be checked for consistency. It works until stage 3 when he says 'impossible to read the security descriptors data stream' how to fix this?

  I tried chkdsk e:/r and it runs before step 3 when I get the "unable to read the security descriptors data stream" and it goes no further.

  I also tried fsutil dirty query e:- but it says something about a parameter incorrect and not if the volume is dirty or clean.

  Then I tried chkdsk e:/f/x - that always gives me the same mistake about it being an incorrect setting.

  As far as I know there is absolutely nothing on E:, I didn't even know that there was an additional drive. Right now I have it turned off so that I can use my computer. It seems to work fine without it. I read an article that said that if I can't fix e: with chkdsk which I have to do a low-level format of the reader? What's my next step? And I can do without the XP disc?

  The syntax

  fsutil dirty query e:

  is correct (except, of course, you try to use from the Recovery Console, where the fsutil command is not available).  Are you logged on as a user with administrative rights when you use fsutil?

  Similarly, the switches /f and/x are not available for chkdsk in the Recovery Console.

  See Recovery Console controls.

  Click on desktop then right-click on E: drive icon and select Properties.  What is indicated for:

  • File system
  • Space used
  • Free space
  • Capacity

  Now double click the icon for E: are shown files?  If not, click Tools > Folder Options > view and select the radio button "Show hidden files and folders" and uncheck "Hide protected files (recommended) operating system.  Now that you see all the files?

  Everything you read 'low level of shaped' is nonsense.  Any modern PC drive cannot be low level formatted by end users.  You can read this, but there is really no necessary even to "zero fill" your drive E: http://seagate.custkb.com/seagate/crm/selfservice/search.jsp?DocId=203931 (I have not checked to see if the WD tools rescuer has similar characteristics to SeaTools for DOS).

  If you are convinced that there is nothing of value on E (for example, installation of backup or restore), you can either format by right-clicking on the drive icon in my computer and selecting "format" or you can start disk management as described previously and use either in electronic format or delete the partition completely.  If you delete the partition, space becomes "unallocated".

  Because I guess C is your system drive (where Windows is), you may be able to use the diskpart tool to extend the partition F to use the unallocated space left if you decide to remove E well it's much easier (and safer) to do with disk management third-party tools such as Easeus Partition Manager free : http://www.partition-tool.com/personal.htm

• Unable to connect to a network printer

  I am unable to connect to my network printer, even if when I run the command 'Connect to the printer' and select 'network', while the program is able to see my network printer, it crashes when I select the printer.

  I was able to connect to the printer in the past, but for some reason any printing interrupted.  I deleted and reinstalled the printer (HP OfficeJet Pro 8600) with the CD that came with the printer and once again, while trying to connect it froze.

  Any suggestions would be greatly appreciated.

  Hi André,.

  Welcome to Microsoft Community where you can find all the answers related to Windows.

  According to the description provided, looks like you can not connect to the network printer.

  I have a couple of steps, which I think should help you with this problem.

  Method 1:

  Try the steps mentioned in this link and check:

  Solve printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Method 2:

  Visit this link to learn more about "Troubleshoot network printer."

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problems

  In addition, visit these links and check:

  What are printer permissions?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-printer-permissions

  Troubleshoot file and printer sharing

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-file-and-printer-sharing

  Hope this information helps. In case you have issues with Windows, post here to Microsoft Community.

• laptop unable to connect to a network it sees.

  It says "Wireless association failed for an unknown reason."  Previously, it would connect then it was on a wired on another network and when off the coast of this configuration, I get the above error message.  When I "try again" ACTIVE Windows Network Diagnostics I get the screen to repair, then the same message again.

  IM happy that you helped... You are welcome :)

• No network adapter driver is available after reinstalling Windows Vista installation disk... Unable to connect to the network

  No network adapter driver is available after reinstalling Windows Vista installation disk... Unable to connect to the network

  Hello

  Know what type of network card you have and download the drivers of its supplier.

  It doesn't matter what it is always a good idea before re-install/upgrade to log on to the computer support page, download independent drivers from there and put them on a flash drive.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• on startup, I get the message, unable to connect to all network drives

  at startup I get message (unable to connect to all network drives) I use windows 7, intel i3, 64-bit and ie9.

  Hello

  Were there any changes (hardware or software) to the computer before the show?

  Method 1: Perform the steps from the link below and see if it helps.

  Programs may be unable to access some network locations after you turn on user account control in Windows Vista or in Windows 7

  Important:  This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  Method 2: Click on the link below and see if it solves the problem.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-Networking/cannot-reconnect-all-network-drives/5c5a4492-1634-4479-91f9-b4d2763b31d2

  Hope this information helps.