laptop unable to connect to a network it sees.

Similar Questions

• Laptop unable to connect to a network printer with WRT54GL Wireless

  Recently, I replaced an old router with a WRT54GL. Initially, I had the installation of the network without security and my PC and laptop had no problem connecting to the printer (Samsung CLP-600N). After that I enabled the security, the laptop can not send jobs to the printer. The discovery software that comes with the printer can find it; It can not all just print to it. My PC (wired LAN) allows to print, but not the laptop wireless.

  As you already know the IP address of the printer, then you need to manually add the printer on your computer port. What is the operating system installed on your computer?

  You can follow this link to add ports on your computer, its for windows 7.

  If its windows Vista, you can follow this link.

• Unable to connect to wireless networking

  My Toshiba laptop has been pre-installed with Windows 7 Home premium 64 - bit OS and it worked quite well with the BB wireless. However, the wireless internet was on and turned off in recent weeks, while other mobile devices, such as iphone, ipad, or laptop, in my household had no such problem. The wireless signal was so strong, but the error message always says "unable to connect to wireless networking. It seemed that there was something wrong with the wireless adapter.

  I got a new adapter properly installed TP-Link wireless. Fortunately, it worked; but unfortunately, it worked for less than 24 hours. It was really frustrating that I, like student full time, depended so much on the wireless network card.

  Help, please! Harry

  Hello

  You can enlighten us with:

  -What model do you use (eg..) L300-123)
  -What version of BIOS is installed?
  -WLAN driver do you use?

  All these questions are answered in PC Diagnostics are under Toshiba app folder in the start menu.

  BR

  Tom

• Unable to connect to the network because the parameters of the computer do not match the requirements of the network.

  The main computer in my house is connected to the web via a modem to our ISP (Cox).  We use a Cisco's Linksys wireless router.  We have configured a new laptop to connect through the router yesterday.  Now my laptop, which had been the connection very well, can't access the network.  When I go in the "network and sharing Center" and pull up nearby wireless networks, our network shows is even more bars, just a red X.  Reads the error message "unable to connect to this network because the settings of that computer to match the parameters required network.»

  I don't know what has changed on our network, but I was unable to understand what these "required parameters" are, so I was unable to change the settings of my laptop to match the requirements.  Pls help.

  Hi Sharpdale,

  Step 1

  I first suggest you to perform network troubleshooting in Windows 7 and check if it finds problems, and if he is able to fix it.

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Step 2

  Use Windows to configure wireless settings and check if it helps to solve the problem.

  a. click on Start menu and select run

  b. type ncpa.cpl, and then click OK to open the menu of the network connections.

  c. Select your Wi - Fi connection service and choose the option change settings of this connection.

  d. go to the wireless tab and select (tick) labeled use Windows to configure my wireless network

  I hope this helps. Let us know the results.

  Thank you and best regards,

   

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Unable to connect to this network

  I have a samsung series 7 chronos 2013 np780z5e the intel centrino n advanced wireless installed, running 64-bit windows 8 6235 card. I can connect to my home network with wpa2-personal encryption and the public WiFi at my University. However, I can not connect to wpa2-enterprise security connection. It finds the network credentials and then immediately provides the message 'Unable to connect to this network', without asking for credentials. This network works fine with other laptops, and I can even connect with my phone. I think it's a matter of windows 8.

  I tried the automatic network troubleshooting and updating to the latest drivers, but neither have worked.
  Update: after network oversight, update drivers and reboot, it works now. Either reboot or forget the add new network and fixed the problem

  Hello

  The majority of connection to Windows 8 breast problems have been resolved by installing the latest driver for the wireless card with obtained from the manufacturer.

  Thanks for sharing the information. In case, if you need help, you can always after your questions related to Windows and your valuable suggestions in the Windows forum.

• Unable to connect to a network printer

  I am unable to connect to my network printer, even if when I run the command 'Connect to the printer' and select 'network', while the program is able to see my network printer, it crashes when I select the printer.

  I was able to connect to the printer in the past, but for some reason any printing interrupted.  I deleted and reinstalled the printer (HP OfficeJet Pro 8600) with the CD that came with the printer and once again, while trying to connect it froze.

  Any suggestions would be greatly appreciated.

  Hi André,.

  Welcome to Microsoft Community where you can find all the answers related to Windows.

  According to the description provided, looks like you can not connect to the network printer.

  I have a couple of steps, which I think should help you with this problem.

  Method 1:

  Try the steps mentioned in this link and check:

  Solve printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Method 2:

  Visit this link to learn more about "Troubleshoot network printer."

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problems

  In addition, visit these links and check:

  What are printer permissions?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-printer-permissions

  Troubleshoot file and printer sharing

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-file-and-printer-sharing

  Hope this information helps. In case you have issues with Windows, post here to Microsoft Community.

• No network adapter driver is available after reinstalling Windows Vista installation disk... Unable to connect to the network

  No network adapter driver is available after reinstalling Windows Vista installation disk... Unable to connect to the network

  Hello

  Know what type of network card you have and download the drivers of its supplier.

  It doesn't matter what it is always a good idea before re-install/upgrade to log on to the computer support page, download independent drivers from there and put them on a flash drive.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Unable to connect to a network or to the Internet on my Dell XPS1530.

  Unable to connect to a network or to the Internet on my Dell XPS1530. When I try to diagnose problem, I get a message that reads "Network Diagnostics cannot run because the Diagnostics Policy Service is not running." Having exhausted the patience all the phone with my IP and Dell, which tells me that it is a problem of Microsoft software. I have two other computers and a PS3, and I am able to connect to the Internet through one any of them. The XPS works under Vista with SP2. Can someone help, please? Thank you.

  Go to start / Control Panel / Administrative Tools / Services and go to diagnostic policy Service and set it to automatic and start it.  If it does not start, check the dependencies and make sure they're too automatic and rnning.  Then see if you can run Network Diagnostics.

  You can get in trouble with your device drivers.  Go to Device Manager by going to start / find and type Device Manager and enter and then double-click on the program icon that appears.  Check each device to a red x, yellow! or white?  These identify devices with problems probably (drivers, but also of conflict or something else).  Click on each for more details and troubleshooting tips.  If you need to get drivers (and you should get those developed to date for the network card and regardless of the device you use to connect (such as a router wireless or such) and all you have time to do - they can help way beyond simply solve this problem), let the computer dealer or the manufacturer of the device (NOT of Microsoft Updates).  In fact, you must disable automatic updates in Windows Update driver as follows:http://www.addictivetips.com/windows-tips/how-to-disable-automatic-driver-installation-in-windows-vista/. Follow these steps to get the drivers: http://pcsupport.about.com/od/driverssupport/ht/driverdlmfgr.htm.  Once you have the drivers, you can install them via the Manager device as follows:http://www.vistax64.com/tutorials/193584-device-manager-install-driver.html.

  When I'm in a lke your situation, I usually start from scratch.  Create a new network connection by ensuring that all settings are correct.  Check all the cables (if there is).  You have already reinstalled the drivers - make sure that no firmware or software is also necessary.  Configure the network sharing settings and make sure that you are ready to discover the network and such.  Check other computers to see their settings to make sure you get yours right and essentially the same thing (the same exatly so is another Vista machine connected in the same way).  Go to start / Control Panel / Internet settings and make sure that it's too fixed properly.  To connect, then try again. If this is not the case, remove some time to cool down and then start again with another new connection.  It's almost certainly a parameter that is not correcct (something no doubt very simple).

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• on startup, I get the message, unable to connect to all network drives

  at startup I get message (unable to connect to all network drives) I use windows 7, intel i3, 64-bit and ie9.

  Hello

  Were there any changes (hardware or software) to the computer before the show?

  Method 1: Perform the steps from the link below and see if it helps.

  Programs may be unable to access some network locations after you turn on user account control in Windows Vista or in Windows 7

  Important:  This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  Method 2: Click on the link below and see if it solves the problem.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-Networking/cannot-reconnect-all-network-drives/5c5a4492-1634-4479-91f9-b4d2763b31d2

  Hope this information helps.

• Unable to connect to a network error - change wifi profile native default

  Unable to connect to my network. When I try to see my network it says wifi native default profile

  
  Original title: change the profile default native wifi

  Hello

  Thanks for posting your question on the Microsoft Community Forums!

  From the problem description, I understand that you can not connect to the wireless network.

  For a complete list of the steps to try, see the tutorial wired and wireless on this page.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/is-is/Windows/network-connection-problem-help#network-problems=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  It will be useful.

  Let us know if you encounter problems under windows in the future. We will be happy to help you.

• Unable to connect to the network "\\localmachine\sharedname" share

  I use VMware vCenter Converter Standalone client, v5.0.0 build-470252, running on a 64-bit Windows 7 computer, try to import a Windows 2008 computer virtual (hosted by VMWare infrastructure) on my local machine.

  At the start of the converter, I have "connecting to a local server.

  Specification of the source system is OK, even if I don't know the certificate error.  The conversion wizard installs his agent and it connects OK.

  To the Destination System, I said:

  
  Type of destination: VMware Workstation or other virtual machines to VMware
  Product VMware: VMware Workstation 8.0.x
  Information on the virtual machine:
  Name: same as the source system, such as detected by the converter
  Location for the virtual machine: \\localmachine\sharedfoldername
  Username and password: my Windows 7 credentials, with full control over \\localmachine\sharedfoldername, the action and the underlying folder.

  "When the converter checks the destination settings, it is reported: unable to connect to the network"\\localmachine\sharedfoldername"share

  So far the measures of investigation:
  -Connection to the share through Windows Explorer works fine; It is possible to write to the share

  -J' tried specifying the share as '\\localhost\sharedfoldername', but get "the share specified network 'localhost\sharedfoldername' does not exist."  It was a bit of a long shot, I guess, but the form does not work in Windows Explorer.

  -Have you tried with the file and print sharing both power - on and off seemed worth a try after looking at other posts on this forum

  The help says 'If you are connected to a local Converter Standalone Server, providing a network path or a local path to the destination directory'.  I tried the local path "C:\Virtual Machines\sharedfoldername", but got the message "error: specified as a (local) drive Destination.»  "Please specify a UNC path such as: \\machine\sharename.

  Aid also States "You have not to provide user credentials if the location is on the local storage of the machine where Converter Standalone server running."  However, the next button is always disabled until credentials are provided.

  Can anyone help please?

  You must be able to access the \\localmachine\sharedname of the * SOURCE * machine. The job of conversions P2V of Windows is to install an agent on the source, then the agent connects to the target (this is why it must be on a network share) and transfers the data. You can browse \\localmachine\sharedname of the source (but not where the converter is installed)?

• Computer laptop 13-c004TU unable to connect to the network

  I just bought a HP 13-c004TU laptop (I think - too small to read). It is to see my home Wi-Fi and available networks. I typed my security key, but it is still saying that it cannot connect to this network. I've been on the phone with my ISP and they do not see why it does not connect. Usually, in these cases, I would be hard-cable router, but the laptop doesn't have a suitable connection port. Can someone help me with this? Of course, being new, it is Win8.1. Thanks in advance.

  Hi @meandu ,

  The only way to connect it is wireless via the router or access point.

  Thank you.

• Re: Satellite L300D - unable to connect via WiFi network

  Any help please? -I just L300D with Vista professional.
  Crossed troubleshooting but still unable to connect via the wireless network - no probs with other laptops.

  When going through "Toshiba assist" message arrives "this wireless network device is disabled.

  Please activate the device"- button wireless is activated with light yellow?

  any ideas?

  Are you sure that the laptop wireless switch is on?
  Look in the Device Manager. Maybe it's the wireless network card disabled. So activate it.

  Also try an update of the WLAN driver. You can find it on the Toshiba site:
  http://forums.computers.Toshiba-Europe.com

• Unable to connect to wireless networks

  I was unable to connect to my wireless network. My network connection on my laptop is enabled and under properties, it says that it's maintenance correctly. However, under the command prompt it says that my ethernet adapter network connection is disconnected. I've alerted to check my connection because my wireless network list went from about 10 ads to 1. 1 on the list is a network installation of HP. I had not seen it. Any suggestions or tips to solve this problem?

  better to go to your vendor manufacturer's site and download the driver from there, if possible, otherwise will do you the needfull Sohail who was Khan network hardware professional VOTE A S HELP FULL IF this REALLY ŒUVRES HELP the OTHER FIND ANSWER FASTER

• Error message: "unable to connect to a windows service windows could not connect to the system event." Unable to connect to the network, Windows Vista Home Edition

  Hello

  When I start my laptop there is a long pause between the home screen and the cover page of my office where the message "unable to connect to a windows service windows has no can connect to the system event. I am unable to connect to networks as says "the dependecy service or group could start. I checked some of the solutions to this problem, including the execution of the 'netsh reset winstock' program that did not work. Any advice would be very helpful. Thank you.

  Hello

  It would be a good idea to run the System File Checker tool to see if you have corrupted files

  "How to use the System File Checker tool to fix the files on system missing or corrupted on Windows Vista or Windows 7"

  http://support.Microsoft.com/kb/929833

  Use the (SFC.exe) System File Checker tool to determine which file is causing the problem and then replace the file. To do this, follow these steps:

  1. Open an elevated command prompt. To do this, click Start, click principally made programs, Accessories, right-click guest, and then click run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click allow.
  2. Type the following command and press ENTER:
     sfc/scannow

     The sfc/scannow command analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.

  ___________________________________________________

  And Malware scan:

  Search for malware, if necessary using the safe mode with networking.

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap the F8 key repeatedly until you are presented with the Boot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  Then, download, install, update and scan your system with the free version of Malwarebytes AntiMalware in Mode safe mode with networking:

  http://www.Malwarebytes.org/products/malwarebytes_free

  See you soon.