Unable to start first CS6

Similar Questions

• Unable to start bootcamp after partitioning El Capitan

  Lonely HI T,

  I recently partitioned the drive where is installed OSX El Capitan. Now, to press the Option key at startup to the top, I can't select my Bootcamp partition to boot.

  Here's the info re: my product:

  Here is some information about: my volumes:

  • I have OSX installed on a partition 'Macintosh SSD' a 500 GB SSD
  • The files are on a 'Macintosh HD' partition in a 1 TB HARD drive
  • I have Windows Bootcamp installed on a "SOLID" NTFS partition in the same 500GB SSD
  • and another NTFS partition for Windows files "LIQUID" in the same 1 TB HARD drive
  • I also have a new partition (which lead to my problem) "ScratchDisk' in the same 500GB SSD

  Also very "SOLID" and "LIQUID" NTFS partitions are currently read-only that is ' owners: disabled "in disk utility after creating a new partition"ScratchDisk"for Photoshop in the same 500GB SSD and SOLID will not show up to start up after pressing the button 'Option '.

  I already had Tuxera NTFS installed but uninstalled.

  Below you will find the following information:

  • diskutil list
  • Cs diskutil list
  • sudo TPG - vv - r see the/dev/disk0
  • sudo fdisk/dev/disk0

  Thank you for the patience and kindness in advance,

  CESCO

  Last login: Tuesday, February 2, 23:22:10 on ttys000

  Cescos-iMac: ~ list of the Cesco$ diskutil

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 500,1 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_HFS Macintosh 250,0 disk0s2 GB SSD

  3: disk0s3 Apple_Boot Recovery 650.0 MB HD

  4: disk0s4 Apple_HFS ScratchDisk 99.2 GB

  5: Microsoft data base SOLID 150,0 GB disk0s5

  / dev/disk1 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * 1.0 TB disk1

  1: EFI EFI 209.7 MB disk1s1

  2: Apple_HFS Macintosh HD 899,2 GB disk1s2

  3: Apple_HFS Recovery HD 650.0 MB disk1s3

  4: Microsoft data base LIQUID 100.0 GB disk1s4

  / dev/disk3 (external, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: FDisk_partition_scheme * GB 500,1 DIS3

  1: Windows_NTFS GB Seagate Expansion Drive 500.1 disk3s1

  Cescos-iMac: ~ Cesco$

  Cescos-iMac: ~ list of cs Cesco$ diskutil

  No logical volume group CoreStorage found

  Cescos-iMac: ~ Cesco$

  Cescos-iMac: ~ Cesco$ sudo TPG - vv - r show/dev/disk0

  Password:

  See the TPG: / dev/disk0: mediasize = 500107862016; SectorSize = 512; blocks = 976773168

  See the TPG: / dev/disk0: PMBR to sector 0

  See the TPG: / dev/disk0: Pri GPT to sector 1

  See the TPG: / dev/disk0: GPT Sec at sector 976773167

  start index size summary

  0 1 PMBR

  1 1 Pri GPT header

  2 32 table GPT Pri

  34 6

  40 409600 1 part TPG - C12A7328-F81F-11D2-BA4B-00A0C93EC93B

  409640 488188328 2 part TPG - 48465300-0000-11AA-AA11-00306543ECAC

  488597968 1269536 3 part TPG - 426F6F74-0000-11AA-AA11-00306543ECAC

  489867504 193675024 4 part TPG - 48465300-0000-11AA-AA11-00306543ECAC

  683542528 262144

  683804672 292968448 5 part TPG - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7

  976773120 15

  976773135 32 table dry GPT

  976773167 1 dry GPT header

  Cescos-iMac: ~ Cesco$

  Cescos-iMac: ~ Cesco$ sudo fdisk/dev/disk0

  Disk: geometry / dev/disk0: 60801/255/63 [976773168 sectors]

  Signature: 0xAA55

  From end

  #: cyl hd s - cyl hd s id [Start - size]

  ------------------------------------------------------------------------

  1: EA 1023 254 63 - 1023 254 63 [1-976773167]

  02:00 0 0 0-0 0 0 [0-0] unused

  03:00 0 0 0-0 0 0 [0-0] unused

  04:00 0 0 0-0 0 0 [0-0] unused

  Cescos-iMac: ~ Cesco$

  Re: Unable to start bootcamp after partitioning El Capitan

  Please after the release of

  sudo dd if = / dev/rdisk0s5 account = 1 2 >/dev/null | hexdump - C

  It will show you the first block of the SOLID wall.

• Windows XP SP3: Unable to start, System Restore cannot drag and drop ALL the files/folders on the desktop and applications, many unable to start, services cannot search, cannot copy or transfer the any files folders...

  After a recent power outage, my system has restarted with a weird and very common Windows problems range. The system boots fine, all my personal files/folders/apps are intact, have suddenly stopped almost all functions of applications, but many crucial functions of the Windows kernel. Everything seems to point to several Windows Services are unable to start (administrative tools on the start menu). I am running Win XP SP3 and that he was going to upgrade to Windows 7, but I wanted to backup everything in advance. As I have 29 000 hours on my C: drive and a lot of time invested in my system, files, and applications, I am extremely reluctant to risk losing my files and applications by performing any type of reinstalling Windows. Strangely, begin to almost all my apps and all my files are accessible for the most part, but I've lost the ability to drag and drop files, folders or items in a list within the applications COMPLETELY. I can't copy or paste anything, can't move the desktop icons (although I can create new files and folders). So at the moment I can't save anything or even a single file transfer to a hard drive on another storage medium. Immediate reaction: try safe mode and try the system restore safe mode has the same problems (likely due to the large number of system services that inexplicably refuses to start) and the system restore says an error window saying "system restore is not able to protect your computer at this time. try restoring the system running and restart again", which of course NEVER changes. It's the equivalent of getting a tire on your car in the middle of nowhere to find the spare tire flat and the missing Jack. I have used to be fanatical about the definition of the regular restore points, but now can not access them. I have backups of most of my personal files, but over years have lost most of the original installation CD for many of my applications (there are over 100 applications on my system) and I don't want to lose the file associations and architecture of directory tree that it took my so long to implement. I started with Win XP media center edition of first (circa 2004 or almost) and have migrated twice more of 3 hard disks and 2 computers. All this time (5 years of daily use), I have NEVER known so many malfunctions for as many Windows basic and vital functions at the same time. I tried a lot of 3rd party "windows fix - it / registry repair" apps, all have no effect. Everything I can speculate is there was some serious damage to the registry and have no idea how/why so many Services refuse to start. In MMC, more than half of the services actually start and run, the rest all give the error message "the service or dependencies is not start (error 1068).» In addition, very oddly, no. APPS or windows appear in the toolbar AT ALL, but the Quick Launch toolbar works very well, just like the tray button and start tasks (?! )!). If I reduce a window, it "disappears" (Nothing on the task bar), but I can restore it using the alt - tab keyboard shortcut to switch apps, so all applications/windows appear on the list of the Task Manager. A few apps is paralyzed bad, as the player windows media, itunes, etc. (I guess because the service windows audio can not not start), some won't start at all, but 90% of them work fine, except to try to copy or back up all files. I can create new files, however. I'm desperate to find a solution to repair XP3 Win WITHOUT losing my installed applications and files, before I try and switch to WIndows 7. Any help/suggestions/links/advice would be much appreciated. I'm an experienced user, but I've never met so many malfunctions based on the OS at a time. I, however, very painfully learned (years before that my system so complex) it's been almost a re-installation of Windows guarantees to lose my installed apps and files, the directory tree architecture associations.

  Help, please!

  I'll be honest with you - your message is so difficult to read that I don't bother to go through all that. Next time consider using white space, ball or points numbered, etc. to make your message more readable. I stopped reading after your first sentence and only scanned the rest quickly. I do not mean to hurt your feelings; just trying to help you get targeted answers you need for the future.

  The blackout has corrupted your Windows installation. Back up your data now. Since you have problems so much, it would be probably best is to remove the hard drive, put it in a USB drive enclosure and attach it to another computer to copy the data OR start the target with Linux Livecd such as Knoppix system and copy the data to an external hard drive. IOW, do not use the damaged windows to try to get your data.

  You can try a repair that will leave your programs and facility data intact, but with this widespread bribery, it is unlikely to work. However, it takes only a few minutes and is so worth a try. If the repair facility does not work there is nothing to do, but a clean install. And Yes, it will mean that over again.

  Consider buying a UPS to help prevent future damage by power outages. For a single computer, you should look for one in the area of $60 to 80. A more expensive UPS is not necessary. Another good disaster recovery strategy is to buy an external hard drive and Acronis True Image. You can image your system (and can make an incremental backup image so that your image is still current). You can apply your image and be back running that you were in relatively few minutes after a hard drive or Windows to fail.

  http://www.michaelstevenstech.com/XPrepairinstall.htm - repair install how-to
  http://michaelstevenstech.com/cleanxpinstall.html - Clean install - how-to
  http://www.elephantboycomputers.com/page2.html#Reinstalling_Windows - you will need at hand MS - MVP - Elephant Boy computers - Don ' t Panic!

• Need help message' w/error Unable to start the s window media Interface. Make sure you have at least WMP10. »

  I downloaded WMP11 to download another program and I get this message ("unable to start the s window media Interface. Make sure you have at least WMP10. »).  This message appears when I click on the new program and it loads.  As soon as it loads the first program screen appears and displays this error message on WMP 10.  When I click ok it goes, but I can't get the new program to do anything.

  So before asking on the problem of new program, I would like to fix this so it keeps popping up.
  I'm not too calculates saavy so I need clarification.

  Thank you

  Where did you downloaded WMP 11?

  Uninstall WMP 11 and check again the issue. If it stops then reinstall WMP 11.

  http://Windows.Microsoft.com/en-us/Windows-XP/help/Windows-Media-Player/11

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=8163

• Unable to start up normally, or any feature of safe mode

  I am unable to start up normally, and I'm unable to boot in safe mode functions.

  When it does not start normally, I get on the desktop with ICONS No. nor START BUTTON.

  I am operating Windows XP SP2 on a Dell Latitude D610 (Laptop).  "Cannot open Volume for Direct access.

  I need advice on that.  Help, please!

  We got a lot of insight.

  First, you need to get your work desk in order to have room for manoeuvre, then you can solve your problem of potential malware.

  What you describe is a situation where the process explorer.exe does not work (probably due to malware).  Think the explorer.exe process IS your desktop... then you must start it manually for now.  If it does not, you will have only wallpaper.

  Of your background image, press CTRL-ALT-DEL and open Task Manager.

  Look at the processes tab and if the process explorer.exe is not running, start it as follows:

  In Task Manager, click file, new task, and in the Open box, enter:

  %windir%\explorer.exe

  Click OK and see if get you your office.

  So if you are able to get into the Internet, follow these steps:

  Download, install, update and do a full scan with these free malware detection programs:
  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
  They can be uninstalled later if you wish.

  Restart and see what things look like.

  That alone cannot resolve, but if all goes well with the deleted malware, then PaulAuckNZ can help to mop up any problems.

• Unable to start - blue screen STOP: 0X0000007E

  original title: STOP: 0X0000007E (0XC0000005, 0X89B16963, 0X8B76B87C, 0X8B76B578)

  I was working on my laptop Acer Aspire and suddenly my restarted windows and then leave her unable to start and just show a blue screen with the error code as STOP: 0X0000007E (0XC0000005, 0X89B16963, 0X8B76B87C, 0X8B76B578).

  I tried to run in safe mode, then even I tried all the options available in the Advanced menu to restart that we get after pressing F8 but just fails. Repair of the system showed the error Impossible to repair in the same way his unable to restore and unable to start with last successful boot setting.

  Kindly let me know what to do I have lots of important data in my hard drive that I don't want to lose.

  Hello

  Unless the drive itself is completely fried the data on disk can be recovered by putting the hard drive
  in another computer as 2nd or a case of external hard drive using a USB connection - then the data
  likely to be backed up or copied to other media.

  Of course, the major problem is that the system does not boot even in Safe Mode.

  Setup/settings (BIOS/CMOS) often F2 so screen shows that it boots CD/DVD on the 1st in the boot order-
  Start with a Windows 7 disc and try the Startup Repair tool. Also, try restoring the system from there. (Don't forget to)
  Set the boot order to when.)

  Those who cannot not helped at all and will need you the help of a real computer store (no leeks and)
  Displays a BestBuy or other stores) or system manufacturer support.

  =================================================================

  Here are the usual methods to troubleshoot the bluescreens if you have access to some and still have a
  problem.

  Check this thread for more information on using BlueScreenView, MyEventViewer and other methods of
  Troubleshoot the BlueScreens - top 3 answers.

  http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

  -----------------------------------------------------------------------------------------------------------------

  The system has RAID? If so, it is very suspicious.

  This error is usually a driver problem and display adapter (video) driver is the most suspicious if she
  may be others. Antivirus/antispyware/security programs, equipment (heat) and major software problems
  can also cause the error. When you get to the section of the driver to use the Troubleshoot utility my generic
  methods in the next message and then return to the if necessary troubleshooting tool.

  Have you recently added hardware or drivers updated? Don't forget to look in Control Panel - Windows
  Updates to see if all drivers have been updated it. Other donor opportunities include the antivirus/anti-
  spyware/security programs.

  When you get to the pilot and sections of the memory of the troubleshooter check the following message to
  update drivers and memory test and then return to the troubleshooter if necessary.

  BCCode: 7F 0x0000007E which is also 0x1000007E

  Cause

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. TO
  interpret, you must identify which exception has been generated.

  Common exception codes are:

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.

  For a complete list of exception codes, see the Ntstatus.h file located in theinc directory
  the Microsoft Windows Driver Kit (WDK).

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques.

  • Make sure you have enough disk space.
  • If a driver is identified in the bug check message, disable the driver or check with the
  • Reference of the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2
  (the address of the exception) must identify the driver or function that caused the problem.

  If the exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system
  has been launched with the /nodebug. switch. This problem should occur infrequently. If it occurs repeatedly,
  Make sure that a kernel debugger is connected and the system is booted with the Switch/DEBUG .

  In case of exception code 0 x 80000002, the trap frame provides additional information.

  If you do not know the specific cause of the exception, consider the following questions:

  • Hardware incompatibility. Make sure all new hardware that is installed is listed in the
  • List of Microsoft Windows Marketplace tested products.
  • Service driver or defective peripheral system. A service driver or defective peripheral system can be
  • responsible for this error. Hardware problems, such as the incompatibilities of the BIOS, memory, conflicts
  • and IRQ conflicts can also generate this error.

  If a driver is listed by name in the bug check message, disable or remove that driver. Disable
  or remove drivers or services that have been recently added. If the error occurs during startup
  sequence and the system partition is formatted with the NTFS file system, you may be able to use safe
  Mode to rename or to delete the faulty driver. If the driver is used as part of the system startup procedure
  in Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third remote
  control program. If this software is installed, you can remove the boot of the computer service
  by using the Recovery Console, and then by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the
  device or the driver that generated the bug check 0x7E.

  You can also disable memory cache BIOS may try to resolve the error. You should also
  Run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system.
  For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or
  Once the installation is complete. A possible cause of the error is lack of disk space for installation and system
  BIOS incompatibilities. For problems during the installation of Windows that are associated with the absence of disc
  space, reduce the number of files on the disk drive hard target. Find and delete any temporary
  the files that you do not have to have files hidden Internet, backup application and.chkfiles files that
  contain fragments of file saved to disk scans. You can also use another hard drive with more drive
  free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.

  BCCode: 7F 0x00000007E who is also a 0x1000007E<-- read="">
  * 1141.html? order = votes http://www.faultwire.com/solutions-fatal_error/System-thread-exception-not-HANDLED-0x0000007E-
  -------------------------------------------------------------------------

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard event viewer
  Windows. TIP - Options - Advanced filter allows you to see a time rather
  of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during ' blue screen of the.
  death ' crashes and displays information about all accidents of a table.
  Free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by drivers of old or damaged, in particular the video drivers
  However, there are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
  program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Does not work
  tell all possible driver issues).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• After the system starts. I get the error message; "" Unable to start Bluetooth stack service "from BTTray.

  After the system starts. I get the error message; "" Unable to start Bluetooth stack service "from BTTray.

  Pls I need help to resolve this error message.

  Concerning

  Unfortunately, this model laptop has a Broadcom bluetooth device or a device of Atheros.

  Try to install the Atheros driver first because it is more common.  If it isn't an Atheros card, Setup HP rejects the update indicating no match of material.

  If this isn't Atheros, install the Broadcom bluetooth driver.

  Here is the page of the driver for your laptop and Windows 7 64-bit.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063&LC=en&cc=us&DLC=en&sw_lang=&product=5218666#n311

  Bluetooth drivers are in the category network drivers.

  Let me know what happens.

• Unable to start the CD player Win2003 Server / removable on the virtual machine: VMware-8(Host: Win7)

  

  Hello

  I am unable to start Win 2003 Server CD disk / removable on a Virtual Machine (the two VMWare 6 and 8). The snap-snap-in error is attached. I have the right configuration of the BIOS to Boot priority, but is taking the PXE ROM option.

  Please help me.

  Thank you

  Remy

  Hello

  1. it doesn't matter that the 'connected' is checked which is normal. "Connect at power on" is important and must be checked that it is on the screenshot.

  2. now, change the "autodetect" option to point to your 'real' cdrom device (that this laptop has).

  3 If this does not convert your cdrom ISO image 2003 and load through the second option that says "use an iso image.

  4. If this still does not work there is only one possible "your 2003 cdrom is NOT bootable. The fact that it autoruns IN Win7 does not mean that is bootable. You should check by placing it in a different machine of cdrom, restart this computer, bios in order to boot from CDROM/DVD first and see if the change boots. If it does not start even from there then for sure this cd is NOT bootable. So, the important thing is to load the cd on time to start and not inside the operating system to work.

  5. try to download an iso of the trial of the internet windows Server 2003 and use that one to see what is happening.

  6. create a new virtual machine and try here or even better to try another machine with Workstation 8 and see what happens.

  7. it is no coincidence if the CD-ROM drive is not recognized within the virtual machine.

• Unable to choose Photoshop CS6 as default application for files JPEG, Win7

  Suddenly, I am unable to choose Photoshop CS6 as the 'Open with' default app in Win7 when I try to open JPEG files.

  I updated Adobe Application Manager and he said Photoshop CS6 is installed and I am able to open Photoshop CS6 without receiving the error 'trial version' more - even if it was a problem until I upgraded to AAM.

  Len Cook

  I was able to change the default value of Viewer Windows for Photoshop photo on my Win 7 machine successfully. The steps that I followed:

  1. Open the control panel in the start menu.
  2. Mine is located on the top ' view by ' category. I clicked on (green link) programs.
  3. Under default programs, I clicked on the blue link to "make a type of file always open in a specific program.
  4. Wait for "Loading."... ». at the end make sure that the list is sorted by name and scroll down to ".jpg". Select it and click the button "Change program...". ».
  5. Do not see that Photoshop listed in recommended programs, to do this, click the small triangle right of other programs. Choose Photoshop and click on the OK button.
  6. Wait for the list to reload and confirm the association has changed.

  Note that you probably need to change this for .jp2, .jpe and .jpeg too in addition to some .jpg.

  

• First CS6 plays is not the Cineform files

  I have a few problems in a project basis of cineform. I am using just stock first CS6 and Cineform Studio premium installed. I use a mac Pro, 24 GB of RAM, nvidia card 2008 cheaper stock (not compatible with the CUDA), with Lion installed. I think that my sequence settings are on DSLR quality corresponding to the resolution of the cineform files. There is a chance that they are sequences of office. I started this project later on CS5 and done my sequences here.

  The problem is that 2 of the 3 times I opened first, thumbnails of clip timeline attract and when I have the monitor of the reading program is in the black. Audio plays back ok, but clips of cineform on the timeline do not work. If I try to open an item in the source monitor, it will update the file in the project location to show "Media disconnected". The media is there and in the first are linking to. If I try to close the first time affected by the foregoing it does not close and I have to force close it. Only a reboot of the system will be first opens correctly after that.

  There are moments where the project opens very well however. I don't see a pattern. If it was a problem of Cineform so I don't expect first to be crashing as if it were. That's why I'm here reported.

  This was solved when we officially supported CS6 in the version v1.2, which was June 8.

• I'm unable to start Firefox. To get the message that it is already running. Cannot find my profile using '% APPDATA%\Mozilla\Firefox\Profiles| '. What should I do

  I'm unable to start Firefox. To get the message that it is already running. Cannot find my profile using '% APPDATA%\Mozilla\Firefox\Profiles| '. Restarting my computer did not help. Because I had this problem I also noticed that all my favorites that I had copied in Windows Internet Explorer also disappeared. I use Firefox as my main search engine and usually do not use Internet Explorer. I am running Windows 7 on my machine.

  Try this add on the profile folder

• Unable to start after you run the product recovery disc

  Hello

  My laptop was a dual boot with windows XP SP3 and ubuntu

  1. He was infected by the virus and when I tried to clean it I removed the wrong file "services.exe", whereas windows does not work good there

  2. when I tried to uninstall the windows update, I get the error following error: 1068: the dependency service or group could not start

  3. so today, I found the toshiba recovery disks, I run and it commpleted, but now am not able to start my laptop.

  4. when I try to re - install windiws xp I got the error below "couln can't find NTLDR.

  Guys, your help will be much appreciated

  Hello

  > I run and it filled, but now am unable to start my laptop

  Are you sure that installation completed successfully? Looks like the damaged MBR or cannot be attributed

• Satellite P15-S420: unable to start Windows XP

  I hope that all makes sense... I'm unable to start after the start page of Windows XP. I think I have assumed that the computer turn off when there is no. The battery may have exhausted and when I plugged it back in and tried to start it would not.

  When the Windows start page is in place, it seems that HD works for awhile, but stops and goes no further. I am able to boot in safe mode and have tried to restore with no effect. When I click on Toshiba Manager of power supply in the control panel I get "Policy of NoteBook Load Fail" this could be a problem.

  What do you think???
  Oh, I have a Satellite P15-S420.

  Hello

  In my opinion, this power saver error message occurs because you started the laptop in safe mode. In this case, the OS doesn't use the Toshiba drivers that are required for the use of additional applications.
  You write about the restore procedure. Have you tried to install the laptop with the supplied restore CD? If this isn't the case, then try it.

• ERROR: Unable to start Bluetooth stack service

  I seldome use features wireless to my pc before, but now that I have the wireless router I frequelty use it. Usually, I turn on the wireless switch and turned off to save the battery. I noticed every time I turn on the radio, after a few minutes, that an error message is displayed:

  BTTray

  ERROR: Unable to start Bluetooth stack service

  I don't know if what is wrong with my laptop. Please if anyone can tell me if what is wrong with this thing. Thank you very much!

  HP pavilion dv6820ee

  OS: Windows Vista editions Home premium.

  Message edited by xXxonins on 12/22/2008 05:27

  Access your product download page and reinstall the software for bluetooth under networks:

  http://h10025.www1.HP.com/ewfrf/wc/softwareList?OS=2093 & LC = on & DLC = in & CC = US & Product = 3716846 & lang = in

  then, under network connections in the network and sharing window - see if you have a bluetooth adapter that is listed.  If you do not use bluetooth, you can turn it off or you should be able to set it up properly.

  If fails it then in Control Panel, under administrative tools, Services - locate service BTtray and disable it.

  HTH

• Satellite P200HD-1DV: the error event to the startup-unable to start a DCOM Server

  Whenever I restart it is extremely slow and in my opinion, caused by the following 2 errors that appear in the system as event ID 10000 event log:

  Unable to start a DCOM Server: {7160A13D-73DA-4CEA-95B9-37356478588A}. Error: '2 '.
  Happened at the start of this command:
  C:\windows\system32\igfxext.exe-integration

  Unable to start a DCOM Server: {078AEF33-C48A-49F7-AFF3-A0EE810BFE7C}. Error: '2 '.
  Happened at the start of this command:
  C:\windows\system32\igfxsrvc.exe-integration

  I think they are Intel drivers, but have failed to find a cure for this problem.
  Other than a real slow start it seems no problem.
  Am that I the only one having this problem and everyone know the cure?

  So, you understand where the problem is but why didn t you have installed graphic drivers intel one another? I mean, you know where is the problem and you can correct it.

  Otherwise, if a reinstallation does not help, it would be better to completely recover your system to eliminate the problem.

  Greetings