Unidentified network problem

Similar Questions

• Vista unidentified network problem

  My HP G60 laptop under vista home premium got an "unidentified network" problem and not able to get on the internet. I even tried to reinstall vista to factory default, still the same problem with my wireless router.

  Spec:

  -HP G60 laptop computer, running vista Home premium 32-bit, with 3 GB of RAM

  -Belkin router

  -I am able to connect via a fine wired line but with a Wi - Fi, it shows constantly 'unidentified network', even if I changed the Private mode in network and sharing Center.

  -J' tried the following: listed an SSID different router, reset the router by default, to reinstall vista, tried other mechanisms, such as specified in the forum, with no difference

  -When you configure the router, I have clone MAC of the laptop to the router to get the connection with Comcast, has done that with network cable connected, internet connection worked well after cloning.

  -no virus SW installed.

  Any suggestions on what might be the solution here? Thank you.

  Hello

  It seems that something is blocking the wireless to connect to the wireless router and to obtain a valid IP address.

  Maybe this can help.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  ------------------

  The wireless card drivers much also install utility wireless of the seller.

  Make sure that if there are teas from Wireless Utility of seller does not work with the native Windows wireless utility (Service WLAN).

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  party like Hello and NetMagic 3rd network managers can block local traffic too.

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Vista "Local access only" and "Unidentified network" problem

  Hi recently my Windows Vista Home Premium - 32-bit has had problems with the internet.

  It was only said 'Local' next to the 'access' and said "Unidentified network" and used to connect me on the internet.

  This problem occurs when you try to connect through an Ethernet cable to the Modem and the router and also while wireless.

  I know that this is not the fault of my Modem/Router, because my laptop says this when I try to connect about internet anybodies.

  Ive spent a good 3 days on this problem, looking for every website I could find searching for answers. NONE of them have worked :(

  Ive done everything except Microsoft and their paying a call answer...

  So if someone can help me, please and id love for it :)

  Also I know people will ask ipconfig/all, but I'll wait for a response and download what the person asking. Thank you.

  I will not need now, I used a program called "Connectify" on my windows 7 laptop. (connectify is a program that acts as a hotspot access point)

  Somehow I was able to connect my Windows Vista computer to the internet via Connectify and I ran all the updates on my laptop with Windows Update, now I am able to connect to my router and modem without any problem.

  Hope that if anyone else has this problem, they can also use Connectify to Windows 7 computers and difficulty there problems internet as I :)

  DjKilla ICE

• Windows Vista gives me an unidentified network problem. I can't access the internet.

  Cannot access internet. what I do?

  Hello

  Did you change your computer?

  Method 1:

  I suggest you to see link and check.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  The problems of Internet connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  WARNING: Reset Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings

  Method 3:

  I also suggest you to reset TCP/IP

  To reset the stack TCP/IP go to this article and either click on "Fix it for me" or follow the instructions to fix it yourself: http://support.microsoft.com/kb/299357 .

  See also:

  How to troubleshoot network connectivity problems in Internet Explorer

  http://support.Microsoft.com/kb/936211

  Note: disable the Windows Firewall and antivirus may make your computer (and your network, if you have one) more vulnerable to damage caused by worms or hackers.

• Satellite L850 - unidentified network, try to use the LAN card

  I have the Satellite L850 and were using the wireless without any problem.

  Now I find that I can't get the network to work just by using my Ethernet cable.
  I tried to turn off the wifi and allowing the PCIe realtech family responsible of the treatment, which is the connection to the local network, but I get unidentified network.

  Y at - it a sort of conflict between wifi even if it is disabled and the connection to the local network.
  I'm pulling out my hair. The LAN worked very well until I decided to try the WIFI.

  Hello

  The unidentified network problem may be related to different causes, and therefore different workaround solutions may be possible.
  First of all I recommend you to uninstall the network adapter driver.
  This can be done in the Device Manager. After the driver has been removed, restart the laptop and install the network driver that you can download on the page of the Toshiba driver.

  2nd solution: reset the reset TCP/IP protocol
  To do this, see the article Microsoft Knowledge base:
  http://support.Microsoft.com/kb/299357

  Check also if you tools of security (firewall, antivirus software, Mcafee) n does affect network connectivity.

• Unidentified network Local Access only on Vista Home Basic using Ethernet.

  Have 2 laptops not identified network Local Access only on Windows Vista Home Basic.  One is a Toshiba and the other is a Dell.  I can use the Ethernet on the Toshiba to one of the The Fire Dept. I work at. (From lastweek, haven't checked since.)  I can't go to the other Station.  Get Local access to the unidentified network only.  I get also home and when I checked the Dell, get the same message.  I can connect wirelessly.  How can I solve the unidentified network problem?

  Hello

  If your system is running Hello , Netmagic or any other party 3rd network try to uninstall.

  Try also.

  Type Cmd in the search text box.

  Press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type route delete 0.0.0.0 press ENTER.

  Type ipconfig/flushdns press enter

  Restart your computer.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Can someone help me with the problem of Vista Home Wireless (unidentified network)

  I recently replaced my wireless router and now I get "Unidentified network - Local access" when you try to connect to my network.

  This problem occurs only with this computer Vista Home.  (All other wireless devices have any problems (Win7 netbook, iPad, PS3, etc).)
  ipconfig/all shows me a valid ip address, subnet mask and gateway also seems to have a Mac address of zero.
  Norton Internet Security was installed, but I have removed and still have the same problem.

  Hello

  Position of your router would be suspicious here. How you are positioned in the router? Are there
  obstacles in the path?

  Actually try updating your driver and disabling the network logon.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.

• Unidentified with Wi - Fi network problem

  I have a small win7 32 bit netbook. I have two wireless sources, a router and an access point. After I saw you come back from vacation, the router wireless connection works fine, but the access point gives me no access to internet, indicating 'unidentified network '. On the network and sharing page, it says 'public network' under 'unidentified network' and I don't know how to change this back to the Home Network. I've deleted and rebuilt the connection of access without success point. Diagnosis cannot make a decision. Any suggestions? Thank you

  No Access Point new... no problem. Thank you.

  On a side note, even if the box is checked and my profile email is correct, I stopped getting notifications. Any suggestions?

  Thanks, Larry

• Windows Vista - unidentified network Local Access only tried everything please help

  Hello

  I have an Acer Aspire M1610 running Windows Vista Home Premium Service Pack 2 and 2 days ago when I turned it on the internet was not working and it says unidentified network Local access only. I use a wired Ethernet connection. I don't know how it happened as before I had used the computer as usual and the Internet worked very well. I did a lot of research and read a few forum posts about this problem and tried a few solutions but non of them worked. I tried the following:
  (1) disable my firewall and anti-virus who didn't work, I turned their back on immediately.

  2) press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type route delete 0.0.0.0 press ENTER.

  Type ipconfig/flushdns press enter

  Restart your computer.

  (3) the internet protocol version 6 clear, disable and enable the thing

  (4) if same Norton software removal tool I had uninstalled the when I got the computer I read that uninstall it by using uninstall windows is not entirely remove it.

  (5) another thing in the command prompt I don't remember exactly what it was, and I can't find the site Web is because I looked so much of.

  (6) I even reset my computer to factory settings and then uninstalled all unnecessary software and trials that come with and used the software again Norton removal tool.

  Does anyone know how to fix this? Any response will be greatly appreciated.

  Thank you

  Hi Alex,

  Have you tried to assign the IP addresses manually?

  I wish that refer you to this article-

  http://support.Microsoft.com/kb/928233/en-us

  Note: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  Back up the registry - http://windows.microsoft.com/en-US/windows-vista/Back-up-the-registry

  Thank you.

• "Receive the error message" number limited unidentified network access.

  Original title: Tp-link-router connects to windows vista Ultimate edition

  Hello

  I have an Acer aspire 5315 laptop with windows vista ultimate installed and I have a router TP-Link TL-WR841N my Wi - Fi. The problem I have is that the laptop does not connect to my router correctly. Limited saying unidentified network that the router works well because I have another pc downstairs which connects to the access router. Security I use is personal wpa2 and I entered my security key in law whom I did it connects then sometimes times out, but usually he must change the home network. And I have file sharing on now before this router I got router belkin 54 g has of worked but developed a fault, so I bought this one instead. Now the strange thing is the laptop connected with wep on the old router. And the laptop has settings to select wpa2 but nothing happens and the security settings for the wireless is set to automatic and is set on the edge b/n/g on the router. I tried everything but no joy I thought maybe my laptop wireless card might be to old for the tp-link router that I have attached a few photos of snip to show you.

  http://ImageShack.us/g/577/10032013357.jpg/

  Hi Fionn,

  Welcome to the Microsoft Community and thanks for posting the question.

  According to the description, you get limited access error.

  The problem may occur if the NIC (Network Interface Card) does not work.

  Click on the link below and see if it helps.

  http://social.technet.Microsoft.com/forums/en-us/itprovistanetworking/thread/70fcbc73-DECA-4ED4-A521-b1de0e0db271/

  Important: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/( )

  Hope this information helps.

  Answer to us if you are having problems with the network or any Windows problem, and we would be happy to help you.

  Good day!

• My internet rpet 'unidentified network' + "the default gateway is not available"...

  My internet was working fine before, but now repeat me 'unidentified network' and I know that's not my internet because I have another laptop that uses the internet itself very well. Then when I try to solve problems, he said "the default gateway is not available"... of the suggestions?

  Hello

  ·         Did you do last changes made on your computer before the show?

  ·         Using internet connection wired or wireless?

  Method 1:

  Follow the steps in troubleshooting from the link and check if that helps.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  Temporarily disable the firewall on your computer and check if it makes a difference.

  Reference:
  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  Note: Makes sure to turn Windows Firewall back, once you have done the troubleshooting.

  Method 3:

  Reset WINSOCK, TCP/IP IPv4 and IPv6 TCP/IP stack.
  a. Click Start and in the search box, type cmd.
  b. right click on command prompt, select "Run as Administrator" to open a command prompt.
  c. at the command prompt, type the following commands:
  netsh winsock reset catalog which resets the WINSOCK entries to the default installation.
  netsh int ipv4 reset reset.log that resets the stack TCP/IP IPv4 default installation.
  netsh int ipv6 reset reset.log resets the default install IPv6 TCP/IP stack.
  d. restart the computer.

  Also, see this KB article:

  How to reset the Protocol Internet (TCP/IP)
  http://support.Microsoft.com/kb/299357

  Kind regards

• free wifi but giving unidentified networks

  I have windows vista in my Dell Inspiron 1525.

  My laptop is connected with wifi but giving unidentified network.
  It works very well with LAN.
  Kindly help me to solve the problem.

  Hi Myriam.

  Thanks for posting the request in the Microsoft Community.

  Were there any changes made on the calculation before the show?

  Follow these steps to resolve the problem:

  Method 1:

  First of all, I suggest for the link and try to run the troubleshooter and check if it helps.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  Try to update the network drivers and check if it helps.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  If the problem is not resolved, please respond with more information, and we will be happy to help you.

  Thank you.

• How can I get unidentified network settings stick, private and change its name?

  I use Windows Internet Connection Sharing (ICS) on my computer at home, because my Internet is wireless usb (AT & T Quicksilver) device that can be plugged directly into my router (Linksys WRT110).  Given that the router accepts only as an internet connection ethernet cables, instead I use my desktop computer as the connection (ICS) and using the router only as a hub, essentially.

  Everything is working well at the moment.  The Office will connect to the internet and other computers and devices connected to the router (wired and wireless) are all works well and can share the internet connection.

  But whenever I restart the desktop computer, the default network is "unidentified network" and as a type of 'Public' without discovery service.  So every time I go to network settings and make it private.  It works fine until the next reboot.  In addition, I am not able to change the network name.  The field seems open for entry, but selecting and typing does nothing.

  I don't know if it's relevant, but other devices to connect to the network are laptops (of various working groups, need to be since they are mainly used to work) and a DirecTV DVR, using Mediashare (via Windows Media Server).  Yet once, they all work, after doing the private network, but this is lost at every restart of the desktop computer.

  I wish I could have it be a private network that is identified by a name and keep these parameters at each reboot.  But I have yet to find an online solution that worked for me.

  Matt,

  Thank you very much.  It worked like a charm.  I was pulling my hair out on this one for a few months.  Once again, a big thank you!

  For anyone else trying to solve the same problem, here is the summary of the solution.

  I have already had no default gateway specified.  As advised by Matt, I right click on the Local network connection (in network and sharing Center / manage network connections) and went in the IPV4 properties and put in the address of a default gateway (equal to the IP address of my router/hub).  I left the ICS settings and all the way IP addresses which I had them before (with zero in the third byte of the IP address of all and ICS turned on).  I have no registry changes.  The only change is the default gateway.  After this change, a wizard appears to allow me to set up the network properly.  And I could rename and define the private network.  And the changes were intact after several reboots.  Perfect.

  -Andrew

• Second laptop unable to connect; When trying to connect wirelessly, says connection is successful, but the Public unidentified network, no Internet.

  Hi all.

  I'm really sorry to post this question, I must have read 100 other threads on this topic, but none of the solutions seem to work for me.

  I have a home set wireless network in place, which may not have a lot of problems with it that I have a laptop W7 which has a perfect wireless connection, and also our TV connect when you want, as do our phones and Xbox.

  We bought a second hand Acer aspire laptop for our daughter. It is running Vista Edition family Basic. Even if she had the factory reset done on this, because we can connect to the router with an ethernet cable and it works very well, we managed to ensure that all updates of Windows etc are all complete.

  When trying to connect wirelessly, it says connection successful, but it is to a Public unidentified network, and there is no Internet. Also, even if it says Local access, we cannot connect to the router settings page is.

  I have uninstalled and reinstalled the built-in wireless adapter and updated the driver to do this, he says that he is as up-to-date as possible.

  I checked that DHCP is enabled, we tried dynamic and static IP addresses, we have disabled and re ipv6 enabled, we used the command prompt to reset winsock and stack ip, I looked into msconfig services for service # Id_String1.6844f930_1628_4223_b5cc_5bb94b879762 # Apple off but it isn't here.

  I have a real dislike for Norton / products McAfee and there is none of these on the laptop. We will install Comodo Internet Security, Eusing Registry Cleaner, Spybot S & D and Spyware Blaster as soon as the wireless is configured and that the Windows Firewall is disabled.

  We also have many turns of the spin off the coast and laptops, etc. and deactivation and activation of the adapter.

  It seems that all the usual solutions for the lack of connection are not the culprits this time.

  IPconfig for W7 laptop that works well is:

  Microsoft Windows [Version 6.1.7601]
  Copyright (c) 2009 Microsoft Corporation. All rights reserved.

  C:\Users\Adrian>ipconfig/all

  Windows IP configuration

  Name of the host...: Adrian-laptop
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless Network Connection 2 wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft Virtual WiFi Miniport adapt
  Physical address.... : 78-E4-00-D1-5F-6A
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Broadcom 4313 802.11b/g/n
  Physical address.... : 78-E4-00-D1-5F-6A
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::30fd:c01f:ab28:fbf9% 13 (Preferred)
  IPv4 address: 192.168.1.3 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: 13 August 2012 09:16:54
  End of the lease...: August 14, 2012 09:56:23
  ... Default gateway. : 192.168.1.1.
  DHCP server...: 192.168.1.1.
  DHCPv6 IOOKING...: 360244224
  DHCPv6 DUID customer...: 00-01-00-01-13-B2-5C-FD-90-FB-A6-A5-8F-73

  DNS servers...: 192.168.1.1.
  192.168.1.1
  NetBIOS over TCP/IP...: enabled

  Tunnel adapter isatap. {09285A7E-7837-4D7B-994D-C70130D43958}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft ISATAP adapter
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card adapt 6TO4 tunnel:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 card
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 15:

  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2001:0:5ef5:73 b 8: 8ed:720:a3fa:1e53 (Prefer
  Red)
  Address IPv6 local link...: fe80::8ed:720:a3fa:1e53% 24 (Preferred)
  ... Default gateway. : ::
  NetBIOS over TCP/IP...: disabled

  Reusable Microsoft 6To4 tunnel map:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 adapt #2
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 adapt #3
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  IPconfig for the Vista laptop that works wired but not when it's wireless is:

  Microsoft Windows [Version 6.0.6000]
  Copyright (c) 2006 Microsoft Corporation. All rights reserved.

  C:\Users\Adin>ipconfig/all

  Windows IP configuration

  Name of the host...: Georges-PC
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Atheros AR5007EG Wireless Network adapt

  Physical address.... : 00-1D-D9-1B-71-69
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::78c1:cedd:291c:e44b % 11 (Preferred)
  IPv4 address: 192.168.1.2 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: August 13, 2012 11:28:16
  End of the lease...: August 14, 2012 11:28:16
  ... Default gateway. : 192.168.1.1.
  DHCP server...: 192.168.1.1.
  DHCPv6 IOOKING...: 151002585
  DNS servers...: 192.168.1.1.
  192.168.1.1
  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Broadcom NetLink (TM) fast Ethernet
  Physical address.... : 00-1B-38-5C-28-24
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 6:

  The connection-specific DNS suffix. :
  ... Description: isatap. {E409704E-A039 - 41A 8 - BEB9 - 614B6A018}
  493}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::5efe:192.168.1.2%12(Preferred)
  ... Default gateway. :
  DNS servers...: 192.168.1.1.
  192.168.1.1
  NetBIOS over TCP/IP...: disabled

  Card tunnel Local Area Connection * 7:

  The connection-specific DNS suffix. :
  ... Description: isatap. {CC1DD067-8D6C-4BDE-BCC8 - 13921 941
  532}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  ... Default gateway. :
  NetBIOS over TCP/IP...: disabled

  Card tunnel Local Area Connection * 9:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Any help or advice will be most appreciated thanks

  Norton or McAfee pre-mstalled of recovery of the manufacturer media?

  If so, did you uninstall it AND run the tool to remove the appropriate product manufacturer?

  Download the Norton removal by https://www-secure.symantec.com/norton-support/jsp/help-solutions.jsp?lg=english&ct=united+states&docid=20080710133834EN&product=home&version=1&pvid=f-home

  Close all other programs, and then run the tool. When it is complete, reboot the machine if she wants it or not.

  Download the removal of McAfee Development tool from:

  http://download.McAfee.com/Products/Licensed/cust_support_patches/MCPR.exe

  Click on save and save the file to a folder on your computer.

  Navigate to the folder where you saved the file.

  Right-click MCPR.exe and select "Run as Administrator" to run the removal tool.

  When you're finished, restart.

• I tried to connect wifi with my laptop, including wireless I use for a month now, but shows only 2 blue screens without the world down on the right, and he said "unidentified network".

  "Unidentified network".

  Hello, today I tried to connect to my friends wifi with my laptop, including wireless I use it for a month now and its impossible! Down right it shows only 2 blue screens without the World Cup, and he said "unidentified network"! I tried several solutions, I found online as 'install the protocols Internet 4 and 6', make sure that I have the ip auto get same restore point system and safe mode with network! Nothing works... my friend connects with his laptop and I can connect with my smartphone, except my laptop! I have windows vista... Please help me thanks

  Go to: Control Panel, Manager of Devic, adapters to extend your network, click with the right button on your wireless network and click on uninstall.

  Do not put a check in the box: remove the software driver for this device.

  Restart your computer and Windows will install your wireless network.

  If the problem persists, see if your computer manufacturer has an updated driver.

  These articles may help:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  http://support.Microsoft.com/kb/313242