Unit's network communication problems

Similar Questions

• 7 Pro VM fusion for VM network communication problems

  I have a strange problem that I can't understand. My host system is a Macbook Pro with OSx 10.9.4. I have two machines 2012R2 comment server.

  Scenario 1: The two VMS are defined to use bridged network, both get good IP from my router and able to reach internet, etc. I can ping other physical computers on the network. It is cannot ping each other.

  Scenario 2: Two VMS are defined to use the host network only, both get IP on the same subnet and appropriate. The question is not one can ping each other.

  Scenario 3: Virtual machines are set to use NAT, both get appropriate IP and on the same subnet, both can access the internet. Neither one can ping each other.

  Basically, comments of host communication works very well with any network set up, but guest to guest does not. I tried to restart my Mac and reinstall Fusion 7 several times, no luck,

  Any suggestions where to look next? Thank you!

  Check if the ICMP traffic is allowed between the two guests, because the default configuration of Windows Server R2 2012 is to deny.

  You can easily make a test only to disable the Windows Firewall on both virtual machines.

• Home wireless network communication problems

  I can't connect with my other computer on my home wireless network. I don't see the other computer files, on my computer, I could before. I could see them before and I could save the files/folders from one computer to another, but suddnely stopped this from happening.

  I have Windows XP Home Edition

  Hello

  Maybe this can help.

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq#trusted

  Please note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Windows XP file sharing - http://support.microsoft.com/default.aspx?scid=kb;en-us;304040
  Sharing printer XP - http://www.microsoft.com/windowsxp/using/networking/expert/honeycutt_july2.mspx

  Setting Windows native firewall for sharing XP -http://support.microsoft.com/kb/875357

  In Win XP pro you can visually see the setting of authorization/security and configure them according to your preferences.

  http://www.Microsoft.com/windowsxp/using/security/learnmore/AccessControl.mspx#securityTab

  When you have finished the configuration of the system, it is recommended to restart everything the router and all computers involved.

  
  

• OGG-01033 there is a problem in communication networks, a problem of remote files

  Hi gurus,
  
  
  I implement simple one-way replication for a scheme and I am newer to GG.
  

  ERROR   OGG-01033  There is a problem in network communication, a remote file problem, encryption keys fo
  r target and source do not match (if using ENCRYPT) or an unknown error. (Remote file used is 

  Any suggestions?
  
  Best regards

  Hello

  1. where is your rmttrail add order?

  2. you must give the path name exact rmt trail in extracted parameter,.

  3. Add replicat must also be changed.

  for example, try this

  GGSCI > add extract urban tranlog start now
  Added EXTRACT.

  GGSCI > add exttrail/u01/app/oracle/acfsmounts/ogg_gold/TRAIL/lt, from urban 20 megabytes
  EXTTRAIL added.

  GGSCI > add/rmanbackup/gg/trail/lt extract urban rmttrail

  GGSCI > add replicat urban_r, exttrail/rmanbackup/gg/trail/lt, checkpointtable GGATE. CONTROL POINT
  REPLICAT added.

  also modify the extracted file rmttrail prm

  urban excerpt
  --
  --
  --
  remttrail/rmanbackup/gg/trail/lt

  --

  In any case better is worth to use datapump process.

• HP Network Communicator causes blocking IE

  Since the installation of an HP Envy D411c, an additional service, HP Network Communicator causes Internet Explorer to hang up, (i.e. does not connect to the Internet) after a period of inactivity.  The ony then plug on the Internet is to terminate the HP Network Communicator service via the Task Manager > processes tab which then interrupts envy of connectivity of the printer (or restarts the computer).

  An important note he shat funcionality everything all the other wireless capable wireless enabled deivices (i.e. smartphone, Tablet PC, laptop) as well as another printer (HP Photosmart D7460) is still intact (with or without network Communicator) as that seems to exclude router related issues.

  What could be the cause of the interruption and is there a resolution?

  OS: Windows XP SP3 32-bit

  IE: v8.0.6001.18702

  Other printers: HP LaserJet 1220se, HP Photosmart D7460

  Hi elcedar,

  This problem occurs on a computer running Windows XP with driver HP (23 to 24.6 version) installed. Here are the steps to resolve this problem:

  First step: change ink setting alerts

  1. double-click on the icon of the product HP on the desktop or click Start, click programs principally made, click HP and then click your HP product.
  2. in respect of Shopping resources, click estimated ink levels.
  3. click on the Advanced Settings tab.
  4. click on the box only show me ink alerts when I print, and then click Save near the change.
  5 restart the computer. It is important that you restart the computer to solve the problem.

  Second step: disable the computer analysis

  1. click on Actions of Scanner and then click on manage the scan to the computer.
  2. click the button disable.
  3. Click to remove the check mark next to automatically start the Scan of the computer when I connect to Windows.
  4. click on close to save the settings.

  NOTE: to scan from the HP software or from the control panel of the product, reverse the previous steps to temporarily activate the analysis to the setting of the computer. After scanning, clear the new parameter.

  http://goo.GL/fJ0u7

• Network Configuration problem

  Hello:

  Since last week, when I click on an icon, for example, the Page Home/Windows 7 does not come on the screen.  Instead, warning to appear at the top of the screen saying... Problem with Internet connection or Network Configuration problem.  After 5 minutes, or later, however, the screen came, but it is very slow to open web pages.

  This problem occurs most often during the night, however for the last two days, sometimes also during the day.

  Until this problem started out of blue, wireless connection with Comcast was very smooth-ride,... instantamously the homepage of popping up.

  Hints on this would be greatly appreciated.

  Thank you

  This sounds like a problem with your Comcast service. In the United Kingdom, I would suggest that you run a speed test on your connection speed. You can get no doubt do the same wherever you are. While it could be the quality of your line, the calendar offers it's the volume of traffic from when children arrive home from school until they go to bed.

  You could compare notes with other Comcast customers.

  http://forums.Comcast.NET/

  Hope this helps, Gerry Cornell

• If my software update of the Appstore stops to say 1.3 GB of 6.4 GB due to network etc problem it back once again to 1.3 GB rear or all the way from scratch

  If my software update of the Appstore stops to say 1.3 GB of 6.4 GB due to network etc problem it back once again to 1.3 GB rear or all the way from scratch.

  Hello Anshul230499,

  Thank you for using communities of Apple Support.

  If a download was interrupted in the Mac App Store, then whenever you have new Internet download should then restart.

  If a download application is interrupted

  Once an Internet connection is restored, your purchased downloads should restart automatically. The Mac App Store may warn you that there is a problem with the download and ask if you want to restart downloads. Confirming will restart all pending downloads.

  Download time may vary according to the size of the file and the speed of your Internet connection. See this article on purchases made on iTunes Store for more information on the time to download large files.

  Troubleshooting the Mac App Store

  Take care.

• Communication problem series

  Hello

  I want to order an instrument via a Labview serial port, but I am unable to communicate properly with him.  It works perfectly when I use Hyper Terminal, but as soon as I use the ' basic series write and Read.vi ", I have a timeout problem.  'Write' does not give me an error, but the "read" never works.  Unfortunately, no or the controls seem to work.  That seems to be a communication problem.

  Here are the parameters of communication for this instrument:

  Baud rate: 115200

  Data bits: 8

  Stop bits: 1

  Parity: None

  Flow control: no

  Charaters termination: \r\n

  By MAX, the communication port is OK and I am able to open the test Panel.  Howerver, I'm not able to access information when I ask a query, or there is no action to simple commands.

  Thanks for your help

  StarFiber wrote:

  I used the example of LV2009: Advanced Serial write and Read.vi.  Just to make sure that I don't have a mistake in coding. I just did the current value as a default value, so you can see what I actually sent to the instrument.

  I guess that you do not actually send * IDN? given that it is not even a command that is supported by the instrument.

  The Canadian standard requires that you cancel orders in writing with BOTH a \r and \n. Using the 'end writing with stop character?' only the \n is sent as it is what is on the stop character. It is unclear how the device responds, or not at all, if she did not see the \r and \n. So disable this option, the "string to write" play to display in '-' codes mode (right click and select in the context menu) and enter the command, followed by \r\n. otherwise, you could leave this option on, but you must make sure that you add \r to your order in the text box "string to write.

• HP 750 055xt: clean install / desire / network driver problem

  Want to 750-055xt. Bought as a refurb. SSD is small, so I put more in and did a clean install with Windows 7 Professional.

  Internet - network driver problem does not connect and I see that the drivers are missing. I tried searching the site, but I can't find the driver.

  It's not a hardware issue because I can put the other drive and it works fine.

  I am struck an impasse with the search tool. I need to copy the driver on another computer to move.

  All of the suggestions.

  Thank you.

  Hello:

  Page for your model motherboard plug indicates that there is a CG-RTL8151GH-Realtek gigabit ethernet card.

  See if the W7 directly from Realtek driver works - 3rd driver on the list.

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=13&pfid=5&level=5&Conn=4&DownTypeID=3&GETDOWN=false

• Communication problem series with USB serial Hub

  Hi, I have a communications problem when I use an NI USB - 232 (778472 - 01) adapter to control a pressure sensor. There are a lot of posts about it in the forum, but I calmly something a little different. I can't use MAX to control the instrument with the VISA test Panel. So I guess that the USB-232 driver is correctly installed. However, in labivew, even if I choose the instrument source of visa name, it always returns an error (-1073807339) when I run the program. The screenshot of the labview program is attached. Could someone kindly help me with this problem. Thank you very much.

  The system is XP SP 3 Pro.

  The version of Labview is 8.6.

  The MAX version is 4.5.0f0.

  If port by default windows settings exactly match the settings you need for communication, you can get lucky and it will work.  If only one parameter is different, it won't work.

  It is always better to define the parameters in your code.

  Shane.

• Can't get my printer to work error message says: communication problem

  printer error message want to work: communication problem

  Contact the manufacturer of the printer.

• Router C4780 wireless network belkin problem

  I have a C4780 which worked well for several years with at least 2 previous routers. I have a Belkin AC1800DB have changed recently and now unable to connect to the router (laptops are connected wirelessly to Belkin WPA2 network without problem).

  When I run a network of C4780 test report it says local networks are detected (including Belkin WPA2) but shoes FAIL against network name SSID found. Similarly the wireless Assistant from the installation disc, the list of available SSIDS for the connection is empty. C4780 both Belkin have WPS, but this does not work in mode button or Pin.

  Because the problem is to find the SSID for all networks I do not think that his associate Belkin (just strange that the problem occurs at the moment I change the router).  But as the C4780 connected perfectly to my previous router, that I do not understand why I now this problem of wireless network connection.

  Any advice much appreciated.

  Try this.   Configure the router to a wireless channel fixed as 1, 6 or 11, never 'auto '.   'Mixed' mode, try now.

• Network connection problems, forcing APIPA to be always active

  Original title: APIPA
  According to the manual of microsoft
  IPAutoconfigEnabled = 0
  is defined in each group of interface parameters in the registry
  but ipconfig/all says:
  Automatic configuration: Yes
  and tcpip sometimes gets the 169.254.x.x address
  The DHCP service stops
  Network driver has been reset, reinstalled, updated...
  Automatic configuration (APIPA) is still on
  How to solve this problem?
  (Vista x 64)

  Hello

  
  1. is this a wired or wireless?
  2. don't you make changes on the computer before the show?
  3. What is the accurate and complete error message that appears on the computer?
  
  Method 1:
  You can perform network troubleshooting steps from the link:
  Network connection problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems
  Also, try the steps from the link:
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
  
  Method 2:
  You can also reset the stack TCP/IP go to this article and either click on "Fix it for me" or follow the instructions to fix it yourself:
  How to reset the Protocol Internet (TCP/IP)
  http://support.Microsoft.com/kb/299357
  
  Method 3:
  You can try to release and renew the address IP address and check if that helps. To release and renew your IP address follow these steps:
  a. open windows command prompt
  b. click Start - run type cmd and press enter
  c. to release your ip address ipconfig/release , press Enter
  d. to renew your ipconfig/renew IP address
  
  Method 4:
  You can also consult the knowledge base article and check if it helps:
  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233
  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base. How to back up and restore the registry in Windows:
  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

• There was a problem with the Windows Live Hotmail service (a network connectivity problem temporary has nothing to do with your computer).

  There was a problem with the Hotmail service (a network connectivity problem temporary has nothing to do with your computer). Please try again

  . I really need to fix this! Help!
  original title: no answer not before!

  track every step!

  no change!

  I am getting really worried about it!

  Please ask in the forum Hotmail. We do not use it. We cannot answer your question.

  Windows Live Solution Center Hotmail Forum
  http://windowslivehelp.com/forums.aspx?ProductID=1

• Home wireless network connection problems

  What should I do if I normally connect to the wireless network does not appear?  It is not a network card problem, because I can connect to other wireless and school and other places.  I tried to reset the router, ping and by unplugging and seeing what I could understand on the computer at home, but nothing does.  Any ideas or suggestions would be greatly appreciated.

  Thank you.

  Hello

  Have you tried other computers to connect to your router? You use both wire and wireless
  connection?

  Unplug the modem and Router 3 + minutes. And then reconnect the modem - when it is running
  Plug in the router - when it is running - restart the computer. This is known as a hard reset.

  Check with your router manufacturer support.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.