Unpluging printer creates Virtual Port Mismatch

Similar Questions

• HP Envy X 2 cannot create com port error virtual 577

  Hi all

  Reinstalled Windows 8 32-bit HP ENVY X 2 and updated all drivers (again).

  Try to create the virtual com port with two different Xport and FransonGPSGate programs.

  These programs normally create a virtual Com Port that can be used by e.g. two different programs of maritime navigation at the same time.

  Xport responds: error code error Windows Xport pilot 577 from

  Franson GPSgate responds: unable to create virtual serial ports

  What is the solution for this problem?

  Thanks in advance for your answer!

  Learned a lot the last few weeks on Windows 8.

  I will guide you to acquire the same knowledge for Xport and fully operational Maxsea

  First read: http://www.pcworld.com/article/2027593/windows-8-put-its-hidden-security-features-to-work-.html

  You probably missed it but read what follows:

  "Included in the UEFI is a feature called Secure Boot, which avoids unauthorized operating systems and malicious software from running at startup."

  "Windows, you can type msinfo32 in the start menu search box or invites him to run it to find out the version of the BIOS.

  Within windows 8, I saw:

  -A start secure ACER (old machine): unsupported

  -To a HP Envy X 2 (new machine) Secure Boot: enabled.

  Secure boot disabled in Envy of HP X 2 and

  Xport and my older prog navigation are fully operational new.

  Good wind,

  -No.

• How to set up a "dummy" or "virtual" port

  Hi, I'm relatively new to Labview programming.  I work with the NI USB-6212.  I was wondering if it is possible to create a "dummy" or "virtual" port, so I can finally create a port for example line output. port0/line16.  Basically I want some bits to go to this line and the "status quo".

  Any suggestion would be appreciated.

  Thank you

  VK

  There are several ways to address the issue and how you will use this 'virtual' Port is one of the choice between the methods.

  The easiest way is to create a USB-6212 simulation:

  Interfaces and select Max devices

  Right click > create new > DAQmx simulated device or modular instrument

  Expand + M series: DAQ and select NI USB 6212.

  You'll be able to create scales channels etc. that are appropriate for a tasks OR USB 6212 assistant DAQmx will treat it as if it was true, and you can try the task and, LabVIEW code call a task on a simulated device will work just fine.

  The down side is when you actually get material its often difficult to retarget the tasks for using the real device (no option to send the task... no option to replace the device with...) Do not hesitate at the idea of Kudos. If you need to change the task or swap device names and which is not infallible.

  Another option that I use for my development (and, I code by intention... very rarely have any material or simulated in my cube)

  must care not the configuration of the task until I integrate with hardware.  Allows to set the example that I have in my current project:

  

  With the exception of the name of the task that this exact code is part of the project I opened today.  This AE wraps completely all I want to do with this task.  Now, I have the code to fall in my application and can create the easilly task on the target computer.  Notice of Here.vi? I'll just go through the hierarchy of the project and find all instances. Create the task and TEST IT on the live system.  When all instances of here.vi went my code is error free and integrated with the hardware running.

  [edit] it is what happens with a break in three hours while you answer.  Tim beats you to it

• Windows 7 64 bit cannot create local port through registry

  Hi all

  I write a vbs to create a local port to connect to our server to printer (ie the local port for \\PrintServer\PrintQueue1). I can create the succesfully local port by editing the registry HKLM\Software\Microsoft\Windows NT\CurrentVersion\Ports and restart the spooler service in Windows 7 32 bit. However, the same script can not create the port in Windows 7 64 bit. The registry has also been changed, but cannot create the local port after you restart the spooler service. Does anyone know what is difference between 32 and 64-bit Windows when creating the local port?

  Turns out in my case is a subtly incorrect registry key in [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports].  Specifically, the (default) entry has existed as white.  Must read (value not set).  A solution is to export the key to a file... and are looking for online reading: @= "", open the file and delete this line, port of registry and Rename Ports.bad (for backup), and then import the file. "  That's what I did and it worked fine after restarting the spooler.  Another solution might be easier to remove the (default) entry, and then restart the spooler... In any case, I have now all my ports which survive a reboot.

• USB 0001 virtual port for UsB not found

  When inatalling a Xerox Phaser 8560DN to my laptop HP Win 7 professinal it does not find the virtual USB 0001 port for UsB. I installed the printer even to other laptops and no prblem. When you come to select the port the virtual prot is tehre but not so much in this laptop and HP peole say it is not their problem. Any suggestions on what to do?

  Hello

  You don't see any other virtual ports except USB 0001?

  Follow these steps and check if that helps:

  1. go in Control Panel.
  2 Select all Control Panel items.
  3. open devices and printers.
  4. at the top of the window, select Add a printer.
  5. Select Add a local printer.
  6. If you want to choose a Printer Port, select use an existing port.
  7. in the drop-down list, select USB001 or USB0002 (virtual printer to USB Port).
  8. Select the next button.
  9. in the manufacturers section, select HP.
  10. in the printers section, search for your printer model and select it.

  Note: If your printer does not appear in the list of HP, select nearest LaserJet series model number.

  Click the Windows Update button. WU get the database driver for all HP printers.

  Note: the search may take a while.

  When the search is complete, go back to the HP section and your printer should now appear there. Select it and click the next button.

  Your printer appears in the printer name box, click Next again and the printer will be installed.

  Kind regards
  Amal-Microsoft Support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• UCSM VM - FEX create when port-profile name cannot be used. (dot)

  UCSM q with 6120XP 2.01

  I can create using port-profile. (dot) for example "VLAN30 - 192.168.1", but it causes a warning message (pictured below)

  so I try to change the name of VLAN30-192-168-1 it can work very well

  My question is can I use. (point) in my profile of the port name?

  PS. I checked the manual of cisco

  This name can be between 1 and 31 ASCII alphanumeric. You can not

  Use spaces or other special characters as - (dash) _

  (underscore character). (period), and: (colon), and you cannot change this name

  Once the object has been saved.

  Thank you

  We have logged a bug for this CSCtw50228 - thanks to Yasmin!

  Our developers have confirmed that while other objects have name validation, virtual computer Port profiles are not, who raises the error you see because NXOS cannot process ".» (periods).  The names of service profiles are another matter that NXOS has no knowledge of these objects.

  The solution is to avoid using periods in the VM profile names.  Use a dashboard.

  Kind regards

  Robert

• WWPN-derivation-virtualized-port

  So I'm digging the Cisco C210 boxes.  I have several held so far.

  Just got a B series.    I feel like I'm back to Catholic school being scolded!   Hate me this thing! :-)

  I went through a laboratory firefly book to familiarize yourself with the configuration.    I "think" I have everything set up properly...

  I created a service profile, so I could in a few clicks apply to all four of my servers.  When I apply I get

  descr = "Service configuration profile Server1 failed for wwpn-derivation-virtualized-port"

  Good old google wasn't able to help me with this one.  I'm old-school Call Manager and person of Contact Center.  This virtualization stuff is very recent.  No experience with SAN.

  Is anyone able to tell me that I may have missed the error?

  Thanks in advance!

  Del

  Del,

  What WWPN pool is configured for the HBAs in your service profile?

  We can if expected this error message when we use the option 'Default material' and that the blade is installed with Cisco M81KR adapter (it does not have burnt in address WWPN)

  If this is the case, then try to create a WWPN pool and configure the service profile / HBAs to use WWPN from the pool.

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/SW/GUI/config/Guide/2.0/b_UCSM_GUI_Configuration_Guide_2_0_chapter_011111.html#task_106F15198C034D1BA1923DCCE2897F9F

  HTH

  Padma

• NPIV Virtual Port and WWN VM

  Hi guys,.

  Looking at doc NPIV for VCAP-DCA. Little confusion of Virtual Port, NPIV and VM WWN.

  Some study guide talks on up to 4 virtual port by virtual computer. I understand the virtual port pair is WWN assigned to the virtual machine that can be used as vHBA to the FC fabric. In my lab 5.5, I can assign up to 16 pairs WWN on a virtual machine (8 HW).

  I can see the limit of 4 virtual port in the v4.1 document, but couldn't find it in v5 and v5.5. This limit removed from v5 and later?

  Thank you.

  VMware vSphere 4 - ESX and vCenter Server

  Each virtual machine can have up to 4 virtual ports. Active NPIV VMS are assigned exactly 4 WWN NPIV related, which is used to communicate with the physical host bus adapters through virtual ports. As a result, virtual machines can use up to 4 physical HBA to purposes are NPIV.

  Documentation Centre of vSphere 5.5

  In fact, it is given in the documentation of 5.5. You might have missed it. Here is the link for it

  Documentation Centre of vSphere 5.5

  You can have up to 16 WWN. "The documentation States" ""you can create 1 to 16 pairs WWN, which may be mapped to the first from 1 to 16 physical FC HBA on the host. "

• Adding a virtual ports GRPE distributed and obtaining his object reference managed

  I added a group of virtual ports to the DVS using the AddDVPortgroup_Task (...) method.

  Now, I want to recover the object managed this group to port reference.

  Is it possible to get the task itself or what I need to do another discovery of the dvs for this?

  Thank you

  VSphere API documents - AddDVPortgroup_Task, the task does not return the reference to the newly created DVPortgroup. I know that some functions participated once, it's 'info.result' contains the object that has been created, but in the case of DVPortgroup, you will need to ask for it.

  =========================================================================

  William Lam

  VMware vExpert 2009

  Scripts for VMware ESX/ESXi and resources at: http://engineering.ucsb.edu/~duonglt/vmware/

  Twitter: @lamw

  repository scripts vGhetto

  Introduction to the vMA (tips/tricks)

  Getting started with vSphere SDK for Perl

  VMware Code Central - Scripts/code samples for developers and administrators

  VMware developer community

  If you find this information useful, please give points to "correct" or "useful".

• relocation of adobe acrobat 7 prof after upgrading OS but almost creates pdf port

  Download Manager used to reinstall adobe acrobat 7 Professional after the operating system upgrade to windows 7. Installation ends but fails with the error "attention 20225. "Adobe Acrobat 7.0.5 implemented could not create a new point Adobe PDF Port / printer. Adobe is installed but I can no longer print to PDF or use Adobe directly to create the pdf file of the file. This feature was available before reinstallation.

  How can I fix it?

  What you can do, it is installing a PS like the HP 4800PS printer and rename as the Adobe PDF printer. The port should be defined as a FILE:. When you print to the printer, you will save the file somewhere. By default, it is a PS file, usually with a PRN, unless you used something else. Simply open this file in Distiller to complete the creation of the PDF file. It is also possible to configure a control record in Distiller, to automate the process somewhat.

• DAQmx create virtual channel (VI) error-229771 reports

  Hello

  When in a project that I am working to get error-229771 code whenever I try to run 'DAQmx create Virtual Channel (VI)' this does not happen when I create a vi not in a project.  The problem is that this project is very large and it if poster impossible to recreate. It's several hundred vi. Y at - it something that I missed in the forums and support that could explain this. I created the VI below in the project and outside the project. In the project, the error occurs outside the project, it runs without any problems.

  Message:

  229771 error occurred at .vi:1780003 DAQmx create channel (I-voltage-Basic)

  Possible reasons:

  Internal software error has occurred in the MIG software. Please contact the support of National Instruments.

  Task name: _unnamedTask

  Any help would be appreciated.  Thank you, Matt.

  LabVIEW version: 15.052(32bit)

  OR Max Version: 15.0.f0

  NEITHER DAQmx Verson: 15

  OS: windows 7 service pack 1

  PC: Intel Core i7-2600, 8 GB of ram

  Data Aquistion: NEITHER DAQ USB-6289 calibrated June 2015

  This code snippet returns the name of the first channel of analog input on the device first, and then tries to create a task for her. The bed of the canal, then close the task.

  

  Error message

  

  Hi Matthew,

  Thank you for following up after you fix your problem.  I'm glad to hear that you do not encounter this problem more.

  Here is an article that lists the reasons for this error (although unfortunately, I cannot pin down which is the exact cause in this case).

  http://digital.NI.com/public.nsf/allkb/03123D0E8A36C48E862577A4005B6BAA

  NOTE: This article specifies that the error occurs at startup task VI DAQmx.  You do not use the start task VI, so the task starts automatically in the DAQmx Read function.  The error will occur instead in the DAQmx virtual channel create, that you encounter in your error.

  I hope this gives you an idea about what could have gone wrong, and I'm sorry he is no more details.

  Good programming!

• Problem creating virtual disk MD3600i

  I add a MD3600i (with extension MD1200) to a Cluster of servers Windows 2012 new file.  I have connected and configured to the point table to create virtual disks.  When I try to create a disc, the 'Work' spinner appears, then disappears almost instantly.  The wizard never loads.

  -J' tried MDSM from versions of resource disc, 4, 5 and 6 - no change.

  -J' removed and added the table several times.

  -J' updated the firmware newest controller.

  -J' tried both In-Band and Out-of-Band management connections.

  -J' tried with two pools and groups.

  -Out-of-band management stations have been Windows 7 and 8.1

  When running create it a Wizard of the pool, I can create virtual disks even size at the end of the process, but I can't create the readers in the free space remaining (more than enough available for a player)...  I need to be able to create readers as needed, please help!

  I spoke with Dell Support, and the solution was to delete and re-create the host in MDSM.

• want to create virtual hot spot WiFi

  Original title:

  virtual hotspot

  Hi, I have windows 7 home basic.i want to create virtual hot point for wifi but the program is not there.it is to windows 8. until he's I do? Please answer my question

  In fact, Windows 7 includes Microsoft virtual wifi miniport map - which can be used to create a "virtual hotspot.

  First of all, make sure that you have the current driver for your wireless card.  If you have a computer of 'brand', go to the computer manufacturer's web site, enter the information requested on your model and find the correct driver.  Download and install the driver if it is newer than the one currently installed.

  Then follow the directions here--> http://www.wikihow.com/Enable-a-Virtual-WiFi-in-Windows

• Virtual Port Mini adapter from Microsoft has a driver problem - not fixed \vwifimp___ {5d624f94-8850-40c3-a3fa-a4fd2080baf3}

  
  

  {5d624f94-8850-40c3-a3fa-a4fd2080baf3} \vwifimp

  Hello

  Update the WiFi driver - if built-in check with the site of the manufacturer of the system. Then check with the real
  site of the manufacturer of the device if possible. Of course, if a separate device then check with its creator. If not most recent
  driver, then re - install the original.

  The virtual Port is used to allow other WiFi devices to connect to the internet via your computer
  WiFi. If you do not use this function, you can then disable the virtual card. Device Manager-
  Network - Virtual WiFi double click on it - the pilot - Disable tab.

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• I try to print to a port usb of a program back in windows 7 32 bit profitional

  I try to print to a port usb of a program back in windows 7 32 bit profitional

  Hey

  Try the procedure described on the site provided
  http://geekswithblogs.NET/dtotzke/articles/26204.aspx

  See you soon!