updated level & disk failure hard hp spectrum xt

Similar Questions

• Dell xps 8100; Disk failure hard error 2000-0142 0 self test status 79

  Hi guys, I was wandering in the forums for a few hours, now looking for ana response to this question, and can't find anything clear. I have a XPS 8100 that I run a diagnostic and received a 2000-0142 error code that says MSG: error code 2000-0142 hard drive FAILURE 0 self-test status: 79 based on what I read in the forum is that there is a disk failure, and the only recourse is to solve the problem in my view is to replace the drive. Firstly, can someone please give me an absolute confirmation that it is indeed what I have to do, or is there something else I should do to fix this problem first? If a replacement drive is there someone could please tell me how can I do to get my OEM software off the coast of the partition recovery and on my new drive. I now office preinstalled and, of course, premium Windows 7 I would like to see on my new hard drive and I was not provided with one of the disks at the time of purchase. Thanks in advance to all those who respond

  Hi XPS8100kid,

  Welcome to the Dell Community Forum.

  The 200-0142 error is for hard drive failure and you need to replace the hard drive.

  Since the hard drive has not, you would not be able to access the partition recovery on it. Data would be lost and the software already installed on your computer will need to be reinstalled.

  Windows 7 will need to be installed on the new hard drive. Please click the link below to get the procedure of re - install Windows 7.

  http://Dell.to/15MYHsz

  If based in the United States, you can ask for the backup drives by clicking the link below:

  http://Dell.to/Zj7oHA

  I would like to know if additional assistance is needed.

  Thank you and best regards,
  Babita S
  #iworkforDell

  For easy access to the drivers, manuals and updates, please visit our Support Site .

• Pavilion 11-n010dx: disk failure hard error long dst Pavilion 11-n010dx

  I realize after searching for the error that my only solution is to replace my hard drive but I need some advice on what exactly, I need with respect to a new hard drive. Not very tech-saavy. Please notify.
  Failure id 9fnhbr-7b783q-xd7v6k-61ed03.
  Thanks for any help.

  Here is the Service Manual:

  Manual

  Replacement hard drive is shown on page 36 of the manual. Your laptop, plug, came with a disk 5400 RPM 500 GB. This model uses 7mm superslim hard drives is as well as what you buy. There are also options for a solid m2 or normal size state drive solid state SATA drive as a replacement for the mechanical drive slow 5400 RPM. In other words, it would be the perfect opportunity to speed it up a little.

  It would be a 7200 RPM mechanical drive of 500 concerts and would be a good replacement at low cost:

  http://www.Amazon.com/Seagate-laptop-7200rpm-cache-ST500LM021/DP/B00ISKS416/ref=sr_1_2?ie=UTF8&QID=1462017567&SR=8-2&keywords=7mm+laptop+hard+drive

  Solid state drive designed to replace the hard drive:

  http://www.Amazon.com/Samsung-2-5-inch-internal-MZ-75E250B-am/DP/B00OAJ412U/ref=sr_1_1?s=PC&ie=UTF8&QID=1462017682&SR=1-1&keywords=Samsung+850+Evo

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• disk failure hard id psl5vq-5m163t-mfkr5g-60dc03

  The laptop (product ID LW291UA #ABA) displays an error of hard disk, I ran a test that does not immediately and displays the error code [psl5vq-5m163t-mfkr5g-60dc03] during the test drive 1. Operating system is windows 7 starter edition, but the OS does not load consistently. He has previously, but usually moves to a SMART disk error screen and suggests a test drive.  More information about the specific error code are appreciated. Tell me whether or not I have to buy a new HARD drive is also appreciated. The computer is not mine, so I don't have much of an idea how the failure occurred.

  Hello

  The failure ID indicates that your hard drive has failed and you must be replace the part and reinstall the operating system on the unit to get it back if you work.

  If your laptop is still under warranty, contact HP and arrange for the disc replaced.

  If you are out of warranty and would like a guide to replacing the hard drive yourself, let me know.

• Disk failure HARD Tecra R950-104

  Hello

  I have a Toshiba Tecra R950-104 with almost a year.
  Everything works fine except the HARD drive.

  In this period (almost on the year), I got 2 hard drive failure (hdd 2 had to be replaced!).
  Fortunately the issues occurs within the warranty period.

  Y at - it problems with this machine, about the drive HARD (it's a 500 GB, 7200 RPM Toshiba HDD).

  Thank you

  Hello

  HARD drive problems do not portable but depend on the use of HARD drive and use of portable.
  The HARD drive is a wearing part. Sooner or later every HARD drive was going to die.

  This problem can occur because the HARD drive is affected by shocks while moving the laptop. In addition, there a lot of different hard drives on the market. Some are less expensive because of the low quality and some HDD cost more because of good quality.

  If you keep the eyes on the quality of the HARD drive.
  But to be honest, I would never buy a laptop HARD drive. I replaced my HARD drive with an SSD. Its much faster and more sustainable as a HARD drive

• Disk failure hard satellite L650-12N - replaced with SSD - how to recover?

  My HARD drive has failed, so I bought a 256 GB SSD Crucial CT256MX100SSD1. I installed it in the laptop and went to use the recovery CD. It's the bit score correctly as far as I can tell, but to cut a long story short, I think that the recovery disk is missing a few vital pieces of information (read below - I may be wrong).

  So, how do for Satellite L650-12N new recovery discs?

  Thank you
  RQ

  After the partition, it then says "copy files of database recovery.
  some random jargon

  Then he said: «unpack the OS and system/WinRE»
  Set of RECO...
  It says "copy F:\ZZImg\11353XSP.swm to V:\HDDRecovery\SWImg 1/10
  1 file (s) copied.
  Copy of the CRC files
  1 file (s) copied.
  Copy F:\ZZImg\11353XSP2.swm to V:\HDDRecovery\SWImg 2/10
  1 file (s) copied.
  Copy of F:\ZZImg\11353XSP3.swm to V:\HDDRecovery\SWImg 3/10
  1 file (s) copied.
  Copy of F:\ZZImg\11353XSP4.swm to V:\HDDRecovery\SWImg 4/10
  1 file (s) copied.
  Copy of F:\ZZImg\11353XSP5.swm V:\HDDRecovery\SWImg 5/10
  1 file (s) copied. »

  at this stage it says ' insert the next recovery media (containing the F:\ZZImg\11353XSP6.swm file)!
  but the backup I did only has one drive.

  Hmm, for me, it seems that some image packages are missing.
  According to your message, the recovery image must contain 10 packs, but the first recovery disc provides only 5 packages.
  Should be so 2nd drive providing other packages to complete the recovery procedure.

  I m wondering if you already used the recovery disc (CD) in the past.
  Are you sure that this recovery disc has been done correctly 100%?

  From my point of few recovery disk is defective and to recover the laptop, you need a good way to return to work.
  Usually this can be ordered here:
  http://backupmedia.Toshiba.EU/landing.aspx

• HP 15-f023 wm Notebook: what disk failure hard Dothe codes mean?

  I was given a HP 15-f023 wm because it didn't work anymore. I bought a new power adapter, but it still wouldn't start.

  I finally managed to do run Diagnostics, who stumbled on the Hard Drive Smart Check.

  I had the following default ID: 94WKG0-7GX87L-MFPV6K-60ES03

  The product ID is J9M28UA #ABA

  Can someone tell me what means failure and how can I fix it?

  Thank you very much!

  Hello

  Unfortunately, this error indicates a hardware failure on the hard drive, it must be replaced by a new.

  Check the manual page, 44

  http://h10032.www1.HP.com/CTG/manual/c04763947

  750 GB, 5400 rpm 778190-001

  500 GB, 5400 rpm 669299-001

• Disk failure hard satellite L850 - claim under warranty in Sri Lanka

  My brother bought me a Satellite L850 of UAE UNITED a month ago.
  But I'm in sri lanka.

  The problem is now the hard drive does not start and it says to replace the hard drive.
  I have the card with me.

  My question is can I claim the warranty in Sri Lanka?

  Please help me soon as soon as possible.
  Thank you.

  Hello

  If you have not purchased the additional international interest, portable computer s hardware problems can be set only in the country where the phone was purchased.

  But AFAIK that parts such as HARD drive or memory are set at the user level.
  Maybe you n t need to send the laptop to UNITED Arab Emirates for a fix, but maybe the guys would be able to send you a HARD drive under warranty conditions.

  Here you can get all the details on the FSA available worldwide.
  http://www.Toshiba.EU/innovation/generic/ASP_SUPPORT/

  I recommend you to contact the ASP and ask for assistance

• Re: Disk failure hard on my Satellite A305-S6905 1 year

  My hard drive is defective on my laptop [a Satellite A305-S6905] so it was a year old Feb 11' th not guaranteed, now I have to pay someone to put in a new HD, will pay for HD and pay to put a new OS in there because they do not come with operating system disks more, a good I had already bought a Windows 7 disc , but wait... I can't use it, it is an upgrade, so now what am I going to do?

  Hello

  I agree with the user above. Replacing the HARD drive is easy and can be done in a few minutes. On the underside, remove the cover of the HARD drive which is fixed by screws, and then you can exchange the HARD drive.

  Reinstalling Windows, to the disk recovery Toshiba or a disk of Microsoft. All drivers and tools can be downloaded from the Toshiba site.

• disk failure hard compaq presario cq62-231nr

  My compaq presario cq62-231nr (product # XC434UA #aba) stopped working last week and I took it into the store of the computer it is diagnosed. They said that the hard drive has failed and they were unable to get all the files out of it. They wanted about $200 to fix so I just brought home. I bought a hard drive to it (500 GB hitachi) and when I install it myself. I have 4 dvd recovery disks that I made for her when I bought it there are 1 1/2 years. Never done this before so I am a little worried about smooth how it will go. My questions are:

  1-will the recovery discs works

  2 - 500 GB hard drive will I put actually no difference from the old hard drive was a 320 GB

  3 - What steps should I take after I put my hard drive in and start it (insofar as the use of the recovery discs)?

  4 - I need a key at any time in this process? I don't have one that I know of.

  Any help is appreciated!

  Hey, Dan:

  You are the very welcome.

  You have almost...

  When you turn on your PC for the first time after installing the new hard drive, you must press the F9 key to the HP welcome screen.

  This will give you a few startup options.  Your DVD player should appear as one of these options.

  Don't do anything about the selection who again. First, open the DVD drawer and insert the diskette 1 of your set of recovery disks. Close the door and wait a moment – just a few seconds.

  Then select the DVD - ROM drive in the list of the bootable devices in the list of startup options.

  Follow the instructions on the screen.

  You never know how long will last the electrical components.  This is why it is always advisable to keep the backup files.

  There's an old saying... "It is not a question of if a hard drive will fail, but a matter of time."

  Paul

• What to do after a disk failure hard when the latest version was an "Upgrade".

  I recently had a hard drive failure and had to buy a new desktop PC Summit. I have the most recent version is the upgraded version of LR 6 (bought for download). My question is, can I just download this version on the new PC? Or do I have to go back and download the first 'full' version, I bought (LR 3) and then download the upgrade to LR6?

  Hi twoedmunds,

  Just download Lightroom 6 on the new system and enter the serial number upgrade, once you enter the serial number upgrade, it will ask you to select the base product (Lightroom 3) and then apply the serial number for it, that's all you need to do.

  See the download link for Lightroom 6:Install Photoshop Lightroom

  Let us know if that helps.

  Kind regards

  ~ Mohit

• Catalyst Control Centre: host application has stopped working disk failure / hard

  recently started to receive some ' catalyst control centre: host application has stopped working "or messages, usually, I get this message twice. When I started to get this message that I also had another saying of warning that there was an error with my drive hard as it had been corrupted, I think he said something as a "write-back" error message appeared, and I have since then lost most of my desktop icons, pictures, all my music files that I have composed and written , any word docs, etc.

  I tried a virus scan first, defragged my hard drive and tried some system restore points and was able to recover some, not all, desktop icons and my experience, but that's all. all my files are gone, I don't know if it's two separate issues or both part of the same issue, but I would like any info or suggestions on how to get my files back. I've saved over 2 years worth of music that I wrote that I really need to come back! Thanks for all comments and advice

  I just had the same thing happen. lost a lot of files. most is saved but we just moved and my backup HD are still packed. seems that there is a major conflict. check the file sizes in the main files, they are big like my files are there, but when I go down the root more that they are not and the file sizes in these folders don't add to the main folder above? I hope they are just invisible but recoverable. anyone with recommendations. I installed the mechanic system and my machine is stable again, but I get the error messages for the catalyst Center control and the dell support center. There may be a conflict between the 2 programs

• Windows does not start (possible disk failure HARD?) - Windows 7 64 bit.

  Hello. My computer won't start. It leads to the 'Starting Windows' screen, then briefly (VERY briefly) flashes a BSOD and reboot to the Startup Repair.

  I had several errors on my laptop which has eventually lead me to the current situation. I'll start from the beginning just after the specifications of the system, maybe they are connected somehow, or they can help you in some way:

  Plug my computer is the following:

  ACER aspire 5738ZG
  -Pentium Dual-Core 2.4 Ghz
  -4 GB of RAM
  -AMD Radeon 5xxx mobility, 512 VRAM
  -Drive Hitachi 500 GB SATA 5400 RPM
  -Windows 7 Home Premium 64-bit

  The first problem I had was a random BSOD who would leap upward with a certain frequency. I solved by going into safe mode, Device Manager and disable a card Microsoft Virtual Wifi Miniport that I don't remember being there before, and that makes not sense to me (I guess some program like a VM can be installed).

  Second problem were random camera that has begun to occur just after I got rid of the BSOD. I experienced the almost all the time (just after awakening upward, while surfing the internet, games, etc.), but I noticed that it was more frequently when using a game with a kind of communication (like Skype) running program and active on the background, or loading videos. I ran a chkdsk and a memtest, and both gave me good results. These problems I was not able to solve, but I went from more games (like WoW) system-oriented to the less demanding (the binding of Isaac, Dwarf Fortress), which blocks exactly 0 produced despite being a bit much CPU.

  I thought that it would be a heat problem, last week I went instead of a boyfriend and it opens. There was neither significant accumulation of dust, and no missed connections between the motherboard and the rest of the components, and I played for a week without a bump. Something of note, however, there was a brown spot on the label on the drive and under the keyboard, which my friend called "have you you spill coffee on the thing?", but I guess it's a day he just got hot. Don't know if it's of any help.

  Finally, I woke up this morning to find out it was going really, very, very slow, and that my HDD light was on almost all the time. I booted safe mode - it seemed to have locked up on the start when starting on normal screen. And after a while of loading and showing me a light permanently on HDD, it gave me an i/o error (could not take the screenshot before it restarts). I also noticed the icon on the status bar would not connect when I woke up, I won't be too paranoid, but in my opinion, could help the network connections.

  Memtest was clean. I did a chkdsk and it started to detect errors in index (something like "Error Index $021 program xxxx", don't remember the exact number), but had to go to work before it's over. When I got home, it comes to the start of repair screen telling me that Windows was not able to automatically fix errors. The next thing I know, I can't start my computer. I tried Chkdsk from Startup Repair tool CMD prompt, and it will immediately (as in, right this second) display the contents of the drive hard (with no "bad sectors"), but will not fix anything. Moreover, when I switch on the C:\ drive, it just shows empty. Memcheck to the boot and Memtest show RAM is clean.

  So in short, the cause could be a faulty HARD drive? I'm pretty sure it must be something related to her or to the connector block, or, worse, my motherboard is upward (which I really, REALLY whish is not).

  Any help will be less appreciated.

  SATA drives have always seemed to generate more heat than the old ones IDE and your CPU can become quite hot when he's busy too.  You do not have permanent damage normally until you get to about 70, so I would be fairly optimistic about the replacement of the HD unless conditions were very extreme.  Don't forget that if you rebuild your system with a retail DVD of Windows 7, you will probably need download drivers at Acer for things like chipset, video and sound.

  Good luck.

• RAID1 disk failure hard x3650M2

  Hello

  Wasn't sure where to post this!

  I have a server esx 4.0 installed on a x3650M2.

  There are two 73 GB 15 k SAS drives in a mirrored RAID that contains the installation of ESX. One of the disks have failed. IBM kindly send me a replacement drive.

  Can I remove the dead drive and put the new with ESX guests always running and the RAID controller will rebuild the RAID on the new disk?

  OR

  I have to migrate to the other ESX Server guests (temporarily) while I stopped and take the dead drive, put the new, start the server in RAID Manager, rebuild the RAID, reboot esx server and then move the disks back guests?

  Of course, though I do evil to do out of office hours to minimize the risks!

  See you soon

  David

  NP, I would say that this task would be not otherwise than with your base operating system loaded on the server...   If you have the possibility of vmotion guests more... and its your job on the line... take the road in any safe

  -

• Disk failure hard ESXi 3.5 host installed on.

  The hard drive installed on my ESXi 3.5 U3 host failed. When the replacement drive can I install ESXi 3.4 U4 on her plan. All my guest VM installed on a second separate hard drive. The new ESXi installation will see the former guest VM or do I have to rebuild like new?

  Todd L.

  You should be able to import them.

  Browse the store data to the .vmx file, right click and add to the inventory