Updated NIC now I can't connect to vSphere
I have a system with ESXi installed 5.x, I made changes to NICs because for some reason they were only running in half duplex mode for some reason any. The card has been set to Auto and I forced it 100 Full and then I lost the connection to vSphere. I now can not connect to vSphere because it was networking... What can I do now? Im not too experienced with ESXi so Im at a loss.
TIA
Hi AmDD,
Great that you have access KVM! You can do the following to get management on your ESXi rogue server:
- Press
and then logon with 'Root' and password - Select Troubleshooting Options in the customization of the system screen
- Press
to enable the ESXi environment so that it displays ESXi Shell is selected in the right pane - Press
to the local shell - 'Root' login and password
At this point, you should have a shell with ~ # on the screen and a cursor blinking on ready for the entry. If this is the case then continue
- Run network vswitch standard list esxcli (assumes that you use a standard vSwitch and not a distributed vSwitch)
- Note uplink associated with this vSwitch (read the physical network adapters)
- Run network nic set-n vmnic5 - esxcli has
- Repeat for all the vmnic related delinquency vSwitch
Once you have confirmed you have taken over the management of the perpetrator, then you can store as follows:
- Press
to return to the DCUI - Follow steps 1-3 in the first section, but make sure that esxi Shell is disabled
- Press
can again to disconnect from the DCUI - Grab a cold beverage of your choice and sit back to relax
Note: This is not strictly necessary but does not remove the fingerprints
Let us know if it works!
Tags: VMware
Similar Questions
-
Omen 870-003na: updated HP installed updates and now I can't connect using Ethernet or wi - if
Update ran today and installed HP HP sure Connect, Realtek Audio Driver Realtek card reader
Now, I can't connect using Ethernet or Wi - if but my iPad will connect using the same wi - if network.
help, please
OK, well I have now established (by means of uninstalling all the software that has been updated to 12, one piece at a time) that the culprit was Cyberlink Power Media Player 14.
After removing that, all right (and Yes, I created a restore point).
-
Updated the operating system on the server for Windows 2012. Now I can not connect to vcenter.
What version of vCenter Server do you run? Only of vCenter Server 5.0 Update 2 is currently supported on Windows 2012.
André
-
- Question
Why can't I minimizes exceeding 2 Notepad in FF? I used to be able to minimize the notebooks as much as I wanted to. When I search on a topic I keep several notebook open until I finished. FF must have made an update and now I can't do that. Is there a setting I can change that will allow me to do it again?
Also at this time, the length of the sentence, I type has changed.
There is no limit for how far she can extend to the right.Help, please. I'm not very irritable and don't understand Computerese.
Please explain in English every day.
Thanks in advance,bouquet
Bouquet,
Great to hear that your problem is finally solved.
Regarding 2nd query you have raised, it is not possible to have the program running if you turn OFF the computer (it's like saying you want the bulb to keep bright despite off). When stop you the machine, you turn off the power... so there is no way that the current state maintained. When start the computer again the next time it starts on new.
But there are 2 options that can help you with your problem: -.
1 SAVE your changes before you close the program, and choose next time when you start the computer
File ->Open (This way your work is preserved and you need not start afresh next time onwards)
2. instead of turning off the computer, choose to Hibernate. When Hibernate you (and NOT CLOSE) the current state is preserved. This means that if you leave the notebook running he will remain in the same State when you next start your computer the next time.
PS: as this forum is for the FF to discuss related issues, I propose that for further assistance e-mail me at my personal mail ID [email protected]' rather than discuss it here on this forum
Now your problem is solved with kindness mark this as closed discussion (marking/choice of appropriate solution helped you)
-
I accepted the last update. Now, I can not display to the right of the main Itunes store, where top songs, etc would be. As the screen does not. Only on the HOMEPAGE of ITUNES STORE! Help! I've tried everything. Google it. Searched through itunes, etc. It MUST be a bug, because it started right after I accepted the 12.3.3 update on my laptop running Windows 7 32.
I count on the part of the main screen, which is not. Its strange. PLEASE HELP ME! In addition to the main page of the Itunes Store, everything else works fine as before. Music from my library work screens, etc.
I also have exactly the same problem since the last update. Tried to find a way to solve the problem but no luck. Someone please help!
-
I have updated and now I can't get on the internet
I finished the new update and now I can't get on the internet? How can I fix it?
What happens when you try?
-
am getting only a few wifi I do not receive my freewifi company, I was gettig 2 days before now I can't connect, but my roommate can connect
Hi Vijay,
1. have you made changes on the computer before this problem?
2. you receive an error message or error code?
This problem can occur because network settings, refer to the steps in the following Microsoft article and check.
How to troubleshoot wireless network connections in Windows XP Service Pack 2: http://support.microsoft.com/kb/870702
Manage your network connections: http://windows.microsoft.com/en-in/windows-xp/help/networking/manage-network-connections
To set up automatic wireless network configuration: http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/wlan_client_configure.mspx?mfr=true
Hope that the information provided is useful.
-
I installed a copy of XP - now I can't connect to the internet.
We have just received a new laptop, so we moved things around.
We had a desktop computer that was under Windows 2000. We also have a lptop that is provided with Windows XP. I just installed XP on the desktop - now I can't connect to any site on the internet. The 3 are connected using Network Magic to manage the network
The resolution of the screen on the desktop is also off now. I don't get the 4 colors of the Windows symbol & the background is distorted.
I can solve this mess?
Hi GinaQQ,
Follow the suggestions below for a possible solution:
Method 1: You can follow the steps in the article mentioned below.
Programs Internet in Windows XP cannot connect to the Internet via a connection to wide band
http://support.Microsoft.com/kb/307164
Method 2: Also, try to reset the TCP/IP Protocol and check the results.
How to reset the Protocol Internet (TCP/IP)
http://support.Microsoft.com/kb/299357
You can also view the article mentioned below for more information about the screen resolution:
To change your screen resolution
Let us know if that helps.
-
I deleted a virus from my computer this morning with security essentials, now I can't connect to the internet. The connection icon in the lower right corner of the screen says I am connected and the signal strength is 'very good', but I can't go online. The error message I receive when I right click and 'fix' the connection says: "failed to query TCP/IP connection parameters. Cannot continue. " For assistance, contact the person who manages your network. How can I fix it? The computer is a HP Pavilion dv2000.
original title: can't get onlineHello BurnBurn,
I suggest you to re-installing the driver for your network card. This may involve completely un-installing it and re - install: -
I deleted my dial-up access and now I can't connect to internet
I have removed my dial-up access
I deleted my dial-up access and now I can't connect to the internet, how can I get that back
Hello
1. how exactly did you remove the dial-up access?
Method 1:
If you have removed the dial from the network and sharing Center, then it should be detected automatically once you restart the computer.
You can also check the link provided below for more information on the implementation of an incoming VPN or dial-up connection
Set up an incoming VPN or dial-up connection
http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-an-incoming-VPN-or-dial-up-connectionMethod 2:
Perform the system restore. You can restore the computer to a date and time when there are no problems with dial-up access.
Click on the link provided below for more information on restoring the system.
What is system restore?
http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restoreSystem Restore: frequently asked questions
http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions -
original title: Wireless help network device
Help, please. I had to reinstall my windows OS and now I can't connect to my wireless device. When I try it tells me that it cannot detect any wireless network hardware. I am currently connected via my laptop air card. Please help me to find and correct the problem.
Have you installed all of the correct drivers?
-
Help, I've changed the root ESXi via powerCli password, now I can not connect with the web client or the console, but I can still connect to powerCli. The command I used was;
SE connect-VIServer esxihostname-user root - password newpasswd
This production network btw, I have connected to each host and run the above command, these ESXi hosts are not on a domain
y at - it something I have left out. I really appreciate any assistance that you people can provide.
Thank you, Joe
It is probably a longshot, but a lot of things in the land of windows is not sensitive to capital letters as Unix is. I wonder if your new password you put through powerCLI mixed uppercase in it and if the capitalization was abandoned by command windows powerCLI Analyzer, or he interpreted as all capitals or something. If you can still get through the powerCLI you could try to reset the password again to something simple without capitalization mixed case and if your password on ESXi strategy requires a special character, try something different than a "$", like a "_" (I find that a '_' is less likely than some other special characters (, as a '-' or a ' / ' to cause problems with analyzers.).
Edit:
Another thing, you can try before playing with the password once again, is to create a different username ESXi using powerCLI and see if the password ends up what you think, it should be, and if you can get with the client vsphere using it. In this way, you can find out if there are some problems with certain characters or Cap through command powerCLI Analyzer without losing your remaining root by powerCLI access. After some tests, you can understand what went wrong with your initial password change and may be able to fix it with less risk of losing access. I also assume that you can not create a new username on ESXi who is able to change the root password no matter what authority give you it, otherwise, you could create a new username with PowerCLI, then connect to the client vsphere with it and change the password to root from there.
-
My Adobe comes automatically updated and now I can't find many documents I had saved on my note 3. What is going on?
Hello
Your local files are not removed by Acrobat DC.
Please take a look at the following document to find the files the on your Android device.
How to open a PDF in Adobe Acrobat DC on Android
Sorry for the inconvenience.
-
My Adobe is automatically updated and now I can't find many documents I had saved on my iPad. What is going on?
Hello
Do you want to take a look at the "Choose a file location" section in the following document?
How to manage files Acrobat DC for iOS
I suspect that you look at the Recent section. Your can switch to the Local (for files & folders stored on your iPad/iPhone) or Cloud of Document (for files & folders stored in the cloud of Document Adobe, formerly Acrobat.com) to find your "lost" files
Please let us know if you have any additional questions. Thank you.
-
9.3.5 on my IPhone 6 updated and now I can't get wifi
9.3.5 on my Iphone 6 updated and now can't get wifi?
Hello
Follow the steps here:
If your iPhone, iPad or iPod touch connects to a Wi - Fi - Apple Support network
To connect to the Wi - Fi on your iPhone, iPad or iPod touch - Apple Support
Apple recommends the parameters of the Wi - Fi routers and access points are detailed here:
Recommended settings for the WiFi routers and access points - Apple supported
Maybe you are looking for
-
Qosmio F50 issues after update Bios 1.50
Hello I have updated Bios version 1.50.I work with audio software and I noticed the performance issue (about 15%-20% performance reduction!).Operational front is also strange. Now, I can not turn off the lights or start Media center or something else
-
HP Pavilion desktop computer: lack of accelerometerDLL.dll
After I've upgraded to window 10, I got this error message everytime I restart the computer: the program cannot start because accelerometrdll. DLL is missing from your computer... Is there anyway that I can fix this? -Paul
-
What I have to install MSN to receive help from Microsoft?
I don't want to use the e-mail program in MSN so I him have not installed on my system... do I have to download MSN to receive Microsoft servicces help... Is this OK to run Yahoo e-mail program instead of windows/msn e-mail products... If so, why?
-
Restore the Vista color scheme
original title: my Windows Vista window color to go and how do I restore it? My Windows Vista color scheme disappeared from my computer. To turn on my laptop this morning, I realized my taskbar has been a gray flat Strip and my previously round start
-
HP iiip: IIIP HP and windows 8.1 (or 10)
Can I use my printer on my computer windows 8.1 hp iiip? I read the notes on windows 7. Dell support said that it will not work with Windows 8.1 or on 10.