Updates auto, stuck in a reboot loop

Similar Questions

• Computer is stuck in a reboot loop, while security updats

  ORIGINAL TITLE: reboot problem

  Computer is stuck in a reboot loop, while security updats

  Hello

  1 were there any hardware or software changes made on the computer before this problem?

  2. do you get an error message or an error code? If Yes, what is the exact full error message?

  I would suggest trying the following methods and check if it helps.

  Method 1: Try to run the system in safe mode restore.

  Step 1:
  Try to start the computer in safe mode, here is the link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Step 2:
  Once you start the computer in safe mode, try to perform the system restore and check that if it helps, here is the link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  What are the system recovery options in Windows Vista?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

  If you were able to start your computer normally by using the system restore, then refer to the following method, and try to update your windows.

  Method 2: To help resolve the error and other messages, you can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  Note When you perform a clean boot, you may temporarily lose some functionality. When you start the computer as usual, the function returns. However, you may receive the error message, or you can experience the original behavior.

  Note: follow step 7 to reset the computer to start as usual after the boot process.

  http://support.Microsoft.com/kb/929135

  See the following help link.

  Problems with installing updates

  http://Windows.Microsoft.com/en-us/Windows7/troubleshoot-problems-with-installing-updates

  Hope this information helps.

• Reference Dell Vista stuck in a reboot loop must restore

  I have a dell desktop computer I bought from rent a Center about 2 years ago. It comes with Windows Vista. They don't did me not a recovery disk. I had a lot of questions and restore points were not helping, so I went through f8 and fact a reset. After that she completed successfully I clicked on finish, and it began to restart, which I expected.

  Now, however, he is stuck in a reboot loop. It gets to the screen that has Dell on this, with the f2, f12 options in the right corner, and then start again again and again. I tried to press f8 and hope go in safe mode and see what was up, but f8 does not open and f2 and f12 are not help at this point. they give me boot priority and so on but no real start until now kind of options. It is possible that windows doesn't have factory loaded, and now I have simply no operating system?  They say they have a reset disk can I come down and use, but im wondering if this will help because I can't really get anywhere or if im just done...

  No messages online that I was looking for really specific my situation...

  * original title - Dell Vista Start Up start up loop *.

  Hello

  ·         Did you follow the steps in this article to restore the computer to factory settings?

  If a factory restore full does not lead to a fully functional version of Windows then you have a hardware problem. I came in contact with Dell technical support.

  Diana

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• HP Windows 7 stuck in a reboot loop

  Hi all

  Recently, I accidentally upgraded my HP Envy 14 from Windows 7 to Windows 10 and let the month pass without switch back.  Due to one host of other problems that have arisen, I decided to Windows 7, so I took out my old Windows 7 recovery disc to re-install Windows 7.

  He successfully reformats the hard drive and everything seems to go well until the end of the installation, when all of a sudden it shuts off and restarts.  He will then get as far as the 'starting windows' screen before it restarts again, each time giving to the screen "Windows is not stopped successfully", is not just a part of the installation process.  He's stuck in this reboot loop.

  Any advice?

  Couple comments:

  I have created a startup repair disk and ran the Startup Repair, but he reported having found no problem.  Very well.

  When you try to start the computer in safe mode, I get to the screen "Windows is set up your computer for first use" and then informs me that Windows cannot complete the installation in safe mode.  He gets up to now in normal mode, however.

  The battery is thus burned - can install Windows on a computer that has failed the test of the battery?  I don't see how there would be a relationship, but I'm really running out of ideas.

  Thanks for any help/insight you have!

  Eventually the recovery disc files are corrupted, try the following:

  Download Windows 7:

  For 5 years, Microsoft made it fairly easy for users of the Windows 7 operating system to get reinstall media. If you have lost your support disc or installation retail collection; either it has been damaged or defective; You can download a copy of the edition that you have licensed from a membership site called Digital River. More recently, Microsoft ended the availability to reinstall media that you can download as a. File ISO in Digital River, which is a digital reproduction of an optical disc.

  It was particularly convenient for people who could not easily get the manufacturer's recovery media, did not want to pay the fees required to get or preferred a clean configuration without the software packaged manufacturers or even a recovery partition does not work. It's easy to use, all you had to do was reinstall and reactivate using the product key located on the certificate of authenticity and download all the drivers on the manufacturers website.

  Given that this option is no longer available, what are your options? See the article for more details:

  How to: What are my options for Windows 7 reinstall media?

  Make sure you scroll down and read the section:

  What to do if you cannot get your manufacturer recovery media, refuse to use or to buy it or the Microsoft Software Recovery Website does not work?

• Pavilion dv6636 stuck in a reboot loop with no boot

  Hello

  I have a Pavilion dv6636 purchased on Oct / 2007 which saw a reboot loop with no boot. By pressing the Start button, I can see the hood leds on, power on (as well as the port for illuminated around blue AC adapter), HD led being turned on once and can hear the pilot DVD is powered and the fan turns, then, after about 10 seconds (while the screen is always black), he stops, remains off for 5 sec , then restarts, stuck in this loop. Experiences I've already done:
  -hard reset
  -reset of memory
  -stable memory locations
  -exchanged memories
  -started with memories (sounded a beep as expected)
  -had started with HD (continued with the same symptoms)
  -F8 or F2 keys pressed during startup (black screen and continued with the same symptoms)
  -F10 key during startup (by pressing F10, it does not shut down as usually does, but rest died, with black screen and rotation of the fan)
  -external monitor plugged in when you start (black screen and continued with the same symptoms)

  Same question occurred in about 4 months ago, but at that time, after break of a week I tried to start and has been a success. Not at the moment.

  Please, any thoughts of what could be the problem?

  Thank you

  Hello Emmanuelle,

  sounded pretty good!

  I got and my laptop is working normally after failed BIOS by following the steps you suggested.

  Now, I have updated the BIOS by the F32 (current release) version and is running successfully.

  Very well.  Thanks about.

• The update of Windows 10 1511 reboot loop Bootcamp BSOD ACPI. SYS

  It is a copy of my thread to http://answers.microsoft.com/en-us/windows/forum/windows_10-performance/windows-10-update-1511-reboot-loop-bootcamp/8653... as I was asked to post here by the Microsoft Support Engineer.

  Hello

  Friday night, I went to bed with a working machine. I had a late 2013 Mac Pro BootCamp running with a Windows 10 Pro installed, the Build version before 1511.

  On Saturday morning, I woke up to my PC restart itself over and over again. It seems that Windows Update has decided to put a new version of Windows 10 on my machine without my knowledge. I discovered this after restoring an acronis backup (which took a few hours because of the number of incremental backups)

  Occasionally (about 1 in 20 restarts) it would blue screen with an error:

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED (ACPI.sys)

  But the rest of the time he would just start, flash a window for a millisecond that says (I think) winlaunch.exe, then restart.

  I tried a lot of things to sort it, including:

  (1) restore from a backup, acronis to Friday morning, running sfc/scannow, and then runs the update

  (2) the creation of a recovery USB, enter the console, change the boot to legacy method, so I can F8, then goes into all security modes and mode of illegal product, but I can find where windows 10 now puts the boot log

  (3) restored from acronis, switched to mac, created a new bootcamp drivers usb, switched to windows and run the option 'fix drivers' before performing the update.

  Ntbtlog.txt is not anywhere on the partition. I ran a dir /s > a.txt then open this a.txt in Notepad and searched him.

  I don't know where to go from here. I can acronis restore of a windows 10 work machine the morning before installing mandatory 1511. I don't know how to delay the update no more, I noted during a restore I had delay on updates that are why it has arisen just now.

  I do not know how to find where this BSOD ACPI.sys will come (even if it happens so rarely) or this that its trying to load just before it crashes (so I can try to delete the driver etc. by the front restored windows to upgrade)

  I guess the widowed causes 10 to do a restore, then the restore fails.

  Overall, I get at the end of my wits with this, to go a completely Windows 10 installation work Friday to more than two wasted days, restore backups, try again, rinse and repeat. It's now Monday morning and I am posting this as a ditch last attempt to solve the problem, your help would be appreciated.

  If you need more information please let me know the location of the files, etc, or their names and I will do my best to have copies available for you.

  I will now restore the backup again, uninstall loading of drivers, and then try the update of windows for the 4th or 5th time.

  Thanks in advance,

  Julian

  Woo Hoo, I've solved the problem!

  I uninstalled the drivers of graphics from AMD (with AMD Driver Cleaner) and Arcronis True Image Home 2013 at the same time, then let Windows Update run its course. Now I have a machine with Windows Version 1511 10!

  It took me 4 days of downtime...

  I hope this helps someone else.

• PC crashed and got stuck in a reboot loop

  Hello, we have a Dell Inspiron 531, and this morning, he had a big crash and then got stuck in a boot loop, blue screen and trying to fix the system. My OH stop it manually. The only change made to the computer of yesterday has been an update to iTunes.

  I just tried to start safe mode and he just tried to restart again and showed a blue screen with a stop error message - I think as a 000000008.  I tried startup repair and he attempted repairs for a few minutes and has now arrived to the top with a message "Startup Repair cannot repair this computer automatically. Here are the details:
  Signature of the problem:
  Problem event name: StartupRepairV2
  Signature of the problem 01: AutoFailover
  02: 6.0.6000.16386.6.0.6001.18000
  03: 6
  04: 131074
  05: 0x8e
  06: 0x8e
  07: 0
  08: 2
  09: WrpRepair
  10: 0
  OS version: 6.0.6000.2.0.0.256.1
  Locale ID: 1033
  Then, there was a message saying remove all devices that have been recently joined. But it is not all delete.
  Some background info-

  There was a problem with the graphics card driver, causing a blue screen (code 116) shortly after the start to the top. In summer, we opened the folder and emptied all the dust, and he stopped the problem. However, he's back. I bought another graphics card, but have not had the opportunity to install again.

  There is also a problem with Windows Update. He has mysteriously stopped working in mid-October.  He attempted to verify updates and then gives an error code 80070005. I started to try to solve this problem a few weeks ago looking for malware. A scan with Kaspersky Internet Security found nothing, but when I run the Microsoft Safety Scanner it finds three feats of Java. He eliminated two and partially removed the other. I always try to get rid completely of partially removed but did not have a lot of time this week to look at it, and the computer seems to be working ok otherwise.

  I also had problems trying to update Adobe Reader recently (' error writing to the file C:\Config...) Make sure you have access to this directory").  I don't know if these things are connected. But thought it would be better to talk about.

  Thank you very much in advance for your help.

  Hello

  The error code indicates that the drive is defective and must be replaced.

  You will be able to connect the drive to another computer or you may use a live cd to backup their data on an external drive.

  Hope this information helps.

• I have installed winxp sp3 on the Intel computer, at first that my computer is stuck in a reboot loop

  At first my computer intel was blocked in a reboot loop, then just the black screen with cursor.

  I could never establish safe mode! I don't have a recovery partition.

  Hello

  Step 1: You can try using disable automatic restart on system failure option and check if you get the error message. If you get one, then return the exact error message.

  a. restart the computer.

  (b) that the computer restarts, press the F8 key repeatedly until you see the Windows Advanced Options screen.

  c. use the arrow keys to select disable automatic system error rebootand press ENTER.

  Step 2: Reinstall Windows XP.

• Laptop stuck in a reboot loop

  Original title: locked cpu

  my computer laptop gateway is in a continuous reboot loop at startup.vista family premium is the operating system, automatic restore or restore to an earlier point in time not working, what a Dick I do?

  Hi Ohmer,

  1 did you recent hardware or changes to the software of the system?

  2. you receive messages or error codes?

  You can try to disable restart of the automactic on the failure of the system and look for the error.

  For more information, you can consult the following article:

  Startup options (including safe mode)

  You can also try the following steps and check if it helps.

  Method 1:

  You can try to perform a test of the last good known Configuration and check if helps solve the problem.

  Using the last good known Configuration

  Method 2:

  You can also check if the problem occurs in safe mode.

  Start your computer in safe mode

  Method 3:

  If the problem occurs in safe mode, and then try to perform a startup repair and check if it helps.

  What are the system recovery options in Windows Vista?

• Windows Update problem! Now it is stuck in a reboot loop!

  I have Windows Vista on a Dell Latitude D620. Today I did a
  Download of updates and it went through the shutdown procedure and restart the computer. Now it is stuck on "Configuring Updates - part 3 of 3 0 0% complete.". There is disk activity, then it restarts, only to return to the exact same page.

  I tried every safe mode, last known good config, etc., but as soon as it starts it goes to this screen. I can't get to a prompt... nada... It comes
  driving me crazy. Even the guy I talked to at Dell do not know which increased or how to fix it.

  Help, please?

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work, try to make a Bootable ERD to do a Startup Repair:

  As is the case with most computers/laptops these days, they do not come with good Vista disc to repair only the recovery disks.

  As your falls into the above category: download the ISO on the provided link and do a repair of the disc.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  You can make a tool to restart system, System Restore, etc. with it.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista repair disc.

  You can do a system restart tool, system, etc it restore.

  There is not a disk of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• After installation of updates, received the critical error, then stuck in a reboot loop, Windows Defender now firewall and Security Center are all off

  I recently downloaded updates from microsoft. One of them was Security Essentials. Well, when I did caused a critical error. My laptop shut down and restarted. then gave me the same error message and rebooted again. He kept in a continuous loop. I tried the system recovery, but that did not work. I managed to get him to stop, but now my firewall is disabled and the Security Center and Windows Defender. If I try to turn it on, it does the same thing again. I don't know what to do to solve this problem. I need help!

  Original title: critical error

  Hello

  1. you have any multiple security software installed in the computer?
   
  2. What is the exact error message?
   
  Please follow the links below to solve the problem.
   
  Method 1
   
  Step 1
   
  Disable all third-party antivirus programs
  
  To disable a firewall, antispyware or antivirus program, right click on the appropriate icon for the firewall, anti-spyware or anti-virus program in the notification area in the taskbar. Then, click exit or click disable.
   

  a. in Windows Vista, click on start toreduce this includes this image, type appwiz.cpl in the Start Search box and press ENTER.

  b. in the list of installed programs, search for and then click on the program in question, and then click Remove.

  c. restart the computer.

  Note After you uninstall a third-party antivirus software, contact the manufacturer of the program or visit the company's Web site to see if a cleaning tool is available to help you remove any remaining files.

  Step 2

  See services

  a. click on start

  b. type services.msc

  c. navigate to the Windows event controller (right click on and select properties)

  d. set the startup type to automatic, start the service, click on apply and OK

  e to navigate to the Base filtering engine (right click on and select properties).

  f. set the startup type to automatic, start the service, click on apply and OK

  g. navigate to 'Windows Firewall' and select Properties (right click on and select properties)

  h. set the startup type to automatic, start the service, click on apply and OK

  Method 2

  Start your computer in a clean boot to avoid conflicts with third-party software.
  
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135
  
  Note: follow step 7 of the article mentioned above to start the computer in normal startup, once you have completed the necessary troubleshooting.

  Method 3
   
  Look for errors in the event viewer.
   
  Please check the Event Viewer logs to find errors in application logs.
  
  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Event-Viewer
  
  Please post the results for a better understanding of the problem causing the reboot.
   
  Hope this helps

• HP Compaq 2510p Bios update failure (stuck in an eternal loop))

  Hello

  I wonder if anyone can advise me please?

  I have a HP Compaq 2510p laptop that starts, displays this error message:

  "Your Bios did not complete the update"

  A few seconds later late in goes to the HP Invent screen. and then again the previous error message. These two screens cycle constantly and there is not only one key that I can use to access the bios settings.

  Presseing F9, F10, F12 or F-everything works. No key command does not work. Can I not boot from the internal drive, CD, USB etc.

  How can I regain access to this faulty machine to restore or repair the bios please?

  Here is a link to the images of the two alternating screens that I'm stuck:

  http://postimg.org/Gallery/2oa73dj8q/

  P.S. This thread has been moved from Windows Vista laptop - Envy, Pavilion, Presario. -Hp moderator of the Forum

  Hello:

  It seems that you have a problem similar to this model (which is basically the same model as yours, except with a 14.1 "display).

  /T5/notebook-HP-ProBook-ZBook/issue-with-BIOS-update-on-Compaq-6910p/m-p/2361103#M165620

  Your situation sounds a little more serious as mine was, because I (another one on this thread) could not get into windows, and flash back to F.17.

• Vista updates step 3 of 3 reboot loop, cannot fix

  I SOLVED THE PROBLEM.  WHAT I DID TO SOLVE IT, IT IS AT THE BOTTOM.

  Someone gave me a laptop to fix, a laptop trying constantly to finsih step 3 in the process of updated, and which never ends and keeps restarting and doing a program over and over again.

  The laptop is a Dell Inspiron 1501 with Vista (no 64 - bit).

  I'll try to explain what I tried, and what has not:

  1. I can't start this laptop mode safe, or find a way to do it. F8 doesn't do nothing, F2 brings BIOS, F12 made up a menu of boot command.

  2. use an Installation of Vista disc, selected "repair your computer [or]" to try to fix the system, there is no.

  3 opportunity disc Installation of Vista to try 'system restore', there is no.

  I then used the steps of the other solutions to this problem which have been posted on this site. Specifically, it is known as the "method 3" and comes from this page: http://support.microsoft.com/kb/949358.

  The strange thing is that when you go to this page, it mentions "Method 3" as the more complex solution, but "method 3" seems to have been cleaned from this page.  Very strange.

  Anyway, I tried the steps that I found in other solutions listed on this site, as follows:

  4 4 navigue sailed to C:\windows\winsxs, renamed the file "pending.xml" to "pending.old" and was able to do it without problem.

  5 open guest entered in regedit, go to HKLM, load the hive, sailed to C:\Windows\System32\config, clicked on it, typed in "Offline_Components", you press on enter, and this window closed and back window of the Registry Editor interface.

  6 tried to delete the registry key 'HLKM\Offline Components\AdvancedInstallersNeedResolving', but it does not exist.

  7 tried to delete the registry key 'HKLM\Offline Components\PendingXmlIdentifier', but it did not exist.  A search in the registry found a subkey named 'PendingXmlIdentifier' in the 'HKLM\Components\' section, but NOT in the section "components of the HKLM\Offline."

  I'm at the stage of ideas. I fixed one of these problems a few months ago on a Vista 64 bit, without too much difficulty.

  Thanks for any help you can offer in this area.

  RESOLVED: I did the following in which the issues listed in step 6 & 7, above.

  1. I created the key that does not exist in step 6: "HLKM\Offline Components\AdvancedInstallersNeedResolving".

  2. I've renamed "PendingXmlIdentifier' as 'PendingXmlIdentifierOLD' key in the location 'HKLM\Components\' (supposed to be the key that should have been at"HKLM\Offline Windows\".

  3. I rebooted on the Windows Setup disc, open a command, went to regedit and delete the key that I created in step 1 above.

  4. I rebooted again, this time without the installation disk and update screen "stage 3 of 3 0%" came, but disappeared in a minute or two, and the computer started normally.

  5. I would HAVE followed the instructions on how to stop this ridiculous problem don't breed, by following the instructions in 'How to avoid this problem' in the 'Further information' section of this page: http://support.microsoft.com/kb/949358.  However, when I downloaded and tried to run the program, he said: "the update does not apply to your system."  Even if he says that it applies to all versions of Vista...

  Hello

  I suggest you to follow these steps and check if that helps:

  Method 1:

  If you have installed a security software on the computer, then I suggest you try to disable temporary and check to see if the same problem happens. Make sure that you enable security software back once the diagnosis is made to prevent the computer from virus attacks.
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Method 2:

  Try to perform the clean boot and check if it helps:

  http://support.Microsoft.com/kb/929135
  NOTE: When you are finished troubleshooting, make sure that restore you the computer mode normal startup such as suggested in step 7 of the above article.

  For more information, see this link:

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-installing-updates

  It will be useful.

• XP is stuck in a reboot loop, cannot use the option to repair with the XP installation CD

  have you tried disturbances on xp installation cd gives just exit and restart option

  * original title - xp keeps rebooting after screen with xp color logo *.

  I had not so long ago.  You can start your PC in safe mode using the F8 key on startup?  So then start in safe mode go to your add/remove software in the control panel and delete all of your drivers.  Mine was a the driver conflict.  Once I removed all my drivers, the system starts fine and then reinstalled the appropriate drivers based on DLLs installed previously.

• Stuck in a reboot loop trying to upgrade to windows 10

  I think I downloaded the free update to windows 10 of my windows 7 ultimate. Windows update, it says my windows 10 upgrade is ready, and I have to restart my pc to start installation. I click the icon of the computer to restart, it restarts my computer, then the message again the same. I shut down the computer and restarted with the same result. Help?

  Download Windows 10:

  How to download official Windows 10 ISO files

  Boot from the bootable copy then do a custom installation:

  How to: perform a customized Windows installation

  then

  Recover personal files from the Windows.old folder, such as pictures of Documents and Windows Live Mail emails in Windows 10