Upgrade GPU for Studio XPS 435MT and indine power load max

Hi, I have a Studio XPS 435MT with a 360W power supply and an ati radeon HD4800 series GPUs (likely a 4850). I want to improve the gpu with a gpu from Gainward GeForce GTX 750 2 GB (one slot), GDDR5. It uses just 55W and there is no external power supply plug, the HD4800, but in the GTX card appears: minimum 300W or more system power supply (with a minimum of 12V current rating of 20A). And I do not know if this 20 a could be a problem, because my Delta DPS-360FB-1 diet doesn't seem to reach the rated current.

What do you suggest me?

Thank you

combined maximum 12V 12VA and 12VB output for this unit is 300W which is 25, but you can't have your cake and eat it too.

If you draw 20 amps on the 12v rail you used 240W leaving 60W for everything else that needs 12V.

And if you use 300W on the 12v rail that leaves 60W max for the 5v / 3.3V through less 10W to + 5VSB.

GTX 750 will be in this case either well, or it does not at all due to the lack of power on one or more tracks.

HD4850 certainly consumes MORE energy than a GTX750 so that only one point of view, it should be good.

Tags: Dell Desktop

Similar Questions

  • Studio XPS 435MT used to power on

    My 2 year old Dell Studio XPS 435MT does not illuminate.  This happened after a short break.  The PC is connected to a surge protector at the time of the failure.  When I try it on, the power button blinks orange and fans to contract.  The fans tremble twice when the power button is pressed - as it tries to start - but he'll nothinhg beyond that.  I have a green light solid on food and a solid amber light on the motherboard.  There is no change of material to this PC.

    Further investigation revealed that the food was good.  I have re-installed THE connections/cards and tried to turn on the unit by disconnecting the components (fans, disks, vid card, etc) one at a time to try to isolate the problem.  I also tried a known working video card.  No matter what I did, it will not turn on.  Same fan tics.  I bought a new computer, removed the hard drive and successfully files retrieved from it using a docking station.  I didn't belive the hard drive was the culprit here.  All the indications stated on the motherboard, so I bought a new (exact same manufacturer / plug).

    The new motherboard was going in and connections were verified tripple.  The PC then propelled straight up.  The computer normally acted through a series of restarts.  I thought that I had this figured out and I was very happy because I liked this computer - but not so fast!  When I stop the PC completely and tried to power on, I got exactly the same problem.  And exactly the same problem no matter what outlet, I used.

    Well, I thought that the food was maybe defective and I tried a new.  Nope - still no luck with that.  I heard that remove and then reinstall the CMOS/BIOS battery has worked for others, so I tried.  Of course - it worked.  The PC starts, but I have to restore the default BIOS settings.  After shutting down, it will still not be able to save, however, without resetting the battery.  As a last effort, I replaced the battery and, of course, who did nothing.

    Please help me because I really don't want to play with that battery every time there is a power failure or stop and I need to get the new card mother $150.00 returned as soon as POSSIBLE if the computer is off help.  Thank you!!!

    Thanks for the suggestion - just replaced the power supply with a 600W Corsair after that first try everything and now the system works very well once more.

    Before replacing, I tested the original power supply and found to work (short circuit green wire with the black) and also tried to isolate the component problem outside the MoBo, but couldn't find any cause.

    I have however noticed that power (at the back of the old PSU) light flickered weakly even if system was off - on the test PSU power LED blinking not.

  • The Studio XPS 435MT graphics card upgrade

    Hi all

    I have a Dell Studio XPS 435mt with these specs:

    Intel Core I7 2.67 ghz

    6 GB of RAM

    ATI Radeon HD 4570 512 MB graphics card (it's the original one)

    I got nothing so far, but now I want to change the graphics card because I want to play games that require higher performance, I play with a resolution of 1920 x 1080 (1080 p).

    So what do you suggest me? What is the best graphics card can I take, compatible with the studio 435mt?

    I don't want to change the other components (and I mean the PSU in particular) I don't want to change the graphics card.

    So what is the graphics card that pushes the limit of this computer?

    I have another question.

    I bought this computer in Italy and it's because I'm Italian xD.

    Now I'm in Boston for the summer holidays and I would buy the card here. There is a compatibility problem between Italian and American computers?

    I mean the GPU are all the same despite the country or there are a few differences to take into account?

    I'm sorry if I am repetitive, but I don't know if my questions are clear and understandable.

    Thanks for your help!

    I have no budget.

    True, but even once, why would you spend $129 when the same one that costs only $89 HERE at Newegg.  Personally, I wouldn't put a high end as the HD 6970 card in your system, but it is up to you.  For me, just is not there, but I know that others have fact.   Cards more recent performance today they run cooler and are smaller than the last generation.  I know there are people who have put in the hot and power hungry GTX 295 in this system.  If you want a high end card without going overboard, take a look at the HD 6850 and HD 6870.  However, if you have money, you can do whatever you want if you use an i7 processor to go with it.  I'm just a little at low cost.

  • Graphics upgrade Dell Studio XPS 435MT

    Model: Studio XPS 435MT
    Processor: Intel Core i7
    Memory: 8 GB
    OS: Windows 64-bit
    Case: In Stock (never did a switch box but would be ready)

    Graphics card: ATI Radeon HD 4350 512 MB 2
    Power: 550w (honestly the first upgrade I did)

    I pulled a lot of games for this thing, and it has served me very well. I am looking to do an update of basic graphics card but want to stay under $ 300.00, I don't want to go too big or too hot for the system (or unnecessarily powerful but I'm okay with that, like if this happens).

    I am also ready to increase the ram, but once again to 8 GB I don't know if I'd get a vein off going up to 16 GB, but at the end of the day it's a learning experience and the installation is always fun.

    Also, I'm ready to tell is don't bother, if it would be better to buy a new system, so I can actually consider doing that but shaped why can't not ask like you people seem quite knowledgeable GD.

    EPS 12V 2.91 compliance means you should be able to use most of the maps, if the power supply is really high spec.

  • Dell Studio XPS 435MT disk hard clean install of Windows Vista

    My hard drive died on my Dell Studio XPS 435MT. I'm doing a clean install of Windows Vista 64 bit on my new HARD drive using DVD relocation provided by Dell with the PC.

    (1) I am not able to boot from the CD/DVD player, where is the DVD of resettlement. I have set the priorities of boot and disabled the boot from the HDD. Whenever I try to boot from the CD/DVD drive, I gives me a message saying "no Diagnostic Utility Partition identified; Press a key to reboot... »

    If I unplug the new HD, then, I am able to boot from the CD/DVD player and I can not for the Windows Setup screens. However, I can't then point nine hard disk installation.

    (2) as I said, I am able to start Windows Setup screens when the HD is initially disconnected during startup. After I get to the Windows Setup screen I plug HD on the motherboard. The new HD must be recognized if I do this? Currently it is not.

    (3) following the instructions here, I said I need to 'prepare a USB SATA key in advance.

    http://dellwindowsreinstallationguide.com/a-clean-install-of-Windows/Windows-Vista-installation/

    http://dellwindowsreinstallationguide.com/a-clean-install-of-Windows/downloading-preparing-and-loading-SATA-drivers/

    What drivers to I need? I tried the drivers at this link, but when I try to load them on the Windows installation screen I get a message saying that they can not be found.

    http://www.Dell.com/support/home/us/en/19/drivers/DriversDetails?driverId=DTT5X&FILEID=2731106696&osCode=WV64&ProductCode=Studio-XPS-435&LanguageCode=en&CategoryID=SA

    Thank you.

    I found this thread on the same subject. Unfortunately your BIOS update can be run from Windows, so that won't help. But down a suggestion to unplug and reconnect the hard drive. Looks like that might work for you.

  • Dell Studio XPS 435mt does not - light light orange card mother

    I had my Studio XPS 435mt for recent years and love it! Normally I leave my machine on almost every day all day so I can access it remotely. Well, today my power went out (the product is connected to a good surge protector) and now it won't turn back on.

    When I plug it in there is a green light to the rear of the machine and internally, there is a orange light, which lights up. When I press the power button nothing happens, not even try to power on. I read a few forums that suggest all of a new power supply, a new motherboard and even a job to 'put your motherboard in the oven' random.

    So my question is can I do anything to check what the problem is? Also, if it of a motherboard problem and needs to be replaced, where is the best place to get a motherboard? Reference Dell sells to them directly or I have to go to a 3rd party to track down?

    Thank you in advance for your help!

    A type of power surge Strip does nothing to protect the PC during a power failure.  You need a 'UPS' unit to protect the PC during short power outages (most).

    As he ran, anything could have happened to the power supply to the motherboard to a component on the motherboard.

    As you have the power to 'keep' alive on the card mother, indicated by orange LED, power supply works somewhat.  Unplug the power connector 24 pins on the motherboard.  Then the rider GREEN wire to a BLACK wire and see if the power turns on (fan running).  If it does, it does not say the PSU is good (only replace it with a known good power is the only true test for a power supply), but it does not say the rotation of the problem is not in the power.  If it does not start, food is the likely problem.

    If the power supply lights the other most likely problem is the motherboard.  Reinstall (unplug and plug back in) the prior panel connector on the motherboard and then give it a try. If it still does not respond, the motherboard is suspect.  The power switch, itself, would be a very remote problem.

    Dell is a source for a replacement motherboard.  There are sites that sell Dell used/given to nine motherboards and ends up with a google search.  Only another mother of exact replacement fit and work.

    Finally, regardless of the tests do or anything that seems as it isolates a certain part, unfortunately only to replace the part really tell you if it's bad.  To avoid buying something you don't need you can make to a PC repair center renamed to what is really wrong.

  • Studio XPS 435 t / 9000 power supply problem

    My diet giving me in my Studio XPS 435 t/9000. The fan is very noisy, but otherwise there is no obvious symptoms. Since the system is about 5 years, I was planning to change some parts.

    My questions are:

    (1) what could be the cause of the fan to be strong, and what are the potential problems with that?

    (2) a system of 435MT 475W PSU would be compatible, or would I need specifically a 435 t?

    The first thing I would do is keep the Office of your garage. Open the side cover. Use compressed air can and blow all the dust that has accumulated in the tower. Blowing from the rear of the PSU and the inside of it. Replace the cover and retest for the noise of the PSU. The power supply 360w on Studio XPS 435MT will not work. The only Dell validated PSU for the Studio XPS 435 t / 9000 has been F217J 475w. The best video cards, we validated our eating 475w were:
    2XTG4 AMD Radeon HD5870
    5X2CH Nvidia GeForce GTX260

    You might consider installing a power supply of higher power, but with a single card video, you need something bigger then a 650w. You could then spend the video card for sale retail Nvidia GTX660.

  • Upgrade GPU for XPS 8700

    As the title says, I have a question about the Dell XPS 8700. I wanted to update the graphics card and after browsing through the forum, I think I already know the answer, but would have an EVGA GeForce GTX 960 to adapt and be compatible.

    The dimensions of the GPU are 4.38 inches x 10.1 inches x 2 inches with a request for a power of 400 W.

    There is an entire thread dedicated to the XPS 8700 / nVidia GTX upgrade.

    http://en.community.Dell.com/support-forums/desktop/f/3515/t/19611037

    you don't need to upgrade the power supply for a GTX 960, and most will fit.

    Regarding the power supply, I went with Seasonic X - 650 s and they are a little longer than the original but adapt easily.

  • Studio XPS 1647 and Windows 8

    Hello

    I want to install Microsoft Windows 8 on my Dell Studio XPS 1647. It will work? I checked the download page for this computer and there is no drivers for this laptop Windows 8... Has anyone tried installing Windows 8 on Studio XPS?

    Thanks for the help.

    Hi Radpl,

    The Studio XPS 1647 has not been tested by Dell with Windows 8. However if you use Windows 7 on your system avoid compatibility problems.

    After the official launch of Windows 8, October 26, 2012, drivers may be available on the Dell support site. However, you can always check the site of the manufacturer for the appropriate drivers. You can also consult the following link for more information on the upgrade of Windows 8. http://Dell.to/SyrDsU You can also see the article: 575111 on www.support.dell.com for upgrade of Windows 8 help.

    Just reply to other questions.

    Thanks and greetings
    Abhishek B
    #iworkfordell

  • Upgrade of RAM Studio XPS 435 t

    I have a Studio XPS 435 t, 64 bit, Windows 7, with 8 MB of Ram. (4) 2 MB sticks in slots 0-3.

    I'll upgrade to Windows 10 and have been informed that I have the 8 MB is less realistic.

    Can I add 4 MB (2) sticks to the empty slots, 4 & 5, or do I put 2 MB sticks in them like the others?

    Or is there a better solution?

    Thanks in advance

    The 435 t is not on the list of Dell systems tested for their compatibility with Win 10. This means it will not work win 10, but you might have a few driver problems that Dell won't help you solve. So before you do anything, it would be a good idea to your Win 7 HDD on external image so that you can quickly return to Win 7 if Win 10 does not work right.  At a minimum, back up all your personal files to an external support.

    Check the RAM installation Manual in the 435 t (not MT). You need the corresponding modules in slots 1,3,5 (blue) and matched modules in 2,4,6 (Pink). If you cannot add 4 GB modules to empty slots 5 and 6 If the other passers-by have 2 GB modules.

    You can get 4 x 4 GB of RAM for this model ~ $100 + at crucial.com to replace what you have now. Or you could buy 3 x 4 GB to fill the blue slots and use the old 3 x 2 GB of RAM (assuming they are all matched) into the pink slots for a total of 18 GB.

    The crucial guarantees that RAM will work if they recommend the modules for a specific system, or they take it back.

    Only you can decide if the cost is worth it for an old (er) PC. And you might want to try upgrading to win 10 first before spending $ on new RAM.

  • Upgrade SSD for Dell XPS 15 9550

    Hello

    I have Dell XPS 9550 with configuration 32 GB SSD + 500 GB HARD disk. I want to upgrade SSD for more space avaliablity.

    But I don't know what type of SSD, I'll need to buy. Also, I read XPS 15 to repair. There are two chapter for the removal and replacement of the SSD in the maintenance manual. First chapter of half-length SSD, second chapter SSD full length.

    What type of SSD is mounted in my laptop? Half or full length?

    How can I identify necessary SSD for me in stores (dimensions, label, etc.)?

    What interface for SSD do I need?  PCIE or SATA?

    What is the map? M2.2280 or PCI-E AIC (-expansion card)?

    Thanks in advance!

    These are all numbers of Dell and descriptions.

    The system uses a PCIe (or is if you want a faster player), 2280 m2 or small size.  UNLESS you buy directly from Dell, it is best NOT to buy versions OEM of SSD (Samsung end pieces in a '1' vs '0' for details).

    OEM spare parts are usually not compatible to end-users by the manufacturer.

    Because you will probably install the operating system for the new SSD, don't forget to make a recovery media set, you need to load the operating system on the larger capacity disk - what you have now is just a cache for the main hard drive.

  • Update graphics card for Studio XPS 8100 with 600W PSU

    Hello

    I just joined the forums of Dell and I was wondering if I could get help for choosing a new graphics card for my studio xps 8100.

    I just bought a power SUPPLY Corsair 600w PSU and was looking for a good graphics card for games (something which runs the games current and near future at the top or above), preferably between 70 and 100 pounds. I took a look at the Geforce GTX 650, and I think that the power supply 600w she'll be fine, but I wasn't sure whether she would be fit in my office. Any advice on the appropriateness of the GTX 650 will fit / work, or any recommendation of something better, would be great.

    See you soon

    Hello Oni21,

    My apologies for the delay in response and if was not clear in my previous post. I wanted to say before you buy the GTX650, take the computer to a local store and check if the graphics card works on the system.

    Please write again if you have any additional questions.

  • upgrade my dell studio xps 1640 vista to windows 7, 8 or 10

    I hear that there is a free update to windows 10. I went to the microsoft site and read through the info and it sounded to me like I can't go from vista to 10. I've been inst I could go to 7 for the upgrade. I loaded the windows Upgrade Advisor 7 and he had to check for the ability. everything seemed fine, except for my driver ati mobility radeon hd 3670. can I load a different driver for my monitor. Talk to me, im not this experience of the computer. I am I get top of my head with upgrade 7 or 10.

    Thank you chris

    Hello

    There is no free upgrade Vista to 7, 8.1, or 10.

    There was this free offer of Vista > 7 years; long expired.

    How does the Windows 7 upgrade Option?

    The Windows 7 upgrade Option is available through participating PC manufacturers on some PC and Microsoft on any purchase of packaged product Windows Vista. The Windows 7 upgrade Option applies to Windows Vista Home Premium, Business and Ultimate editions. Your upgrade to Windows 7 will be the comparable version: so you will get either Windows 7 Home Premium, Windows 7 Professional (upgrade to Windows Vista Business) or Windows 7 Ultimate, respectively. The Windows 7 upgrade Option program works on June 26, 2009 through January 31, 2010. Some manufacturers may choose to shorten the time of upgrade Option.

    @@@@@@@@@@@@@@@@@@@@@@@@@@

    Follow these steps before you buy Windows 7.

    Microsoft sells more than 7; Try Amazon.com.

    Go to your computer / computer laptop manufacturer Web site and see if Windows 7 drivers are available for your make and model computer / laptop.

    Dell:

    http://www.Dell.com/support/drivers/us/en/19/ProductSelector

    If this is not available, Windows 7 will not properly work for you.

    Run the "Windows 7 Upgrade Advisor.

    http://www.Microsoft.com/en-US/Download/details.aspx?ID=20

    Check if your specifications are compatible for Windows 7:

    "Windows 7 system requirements"

    http://Windows.Microsoft.com/en-us/Windows7/products/system-requirements

    "Windows 7 Compatibility Center" for software and hardware:

    http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

    Windows 7 upgrade paths:

    http://TechNet.Microsoft.com/en-us/library/dd772579 (v = ws.10) .aspx

    «Installation and reinstallation of Windows 7»

    http://Windows.Microsoft.com/en-us/Windows7/installing-and-reinstalling-Windows-7

    @@@@@@@@@@@@@@@@@@@@@@@@

    Follow these steps before buy you and upgrade (new installation) of Windows 8.1.

    Check if the manufacturer of your computer/laptop has Windows 8.1 drivers available for your model.

    If this is not available, Windows 8.1 not install and work properly for you.

    There is a lot of information in this first link from Microsoft:

    Download and run the Windows Upgrade Assistant 8.1 of to see if your machine is compatible Windows 8.1 and read the update for Windows 8.1: FAQ here

    "Update to Windows 8.1: FAQ".

    http://Windows.Microsoft.com/en-us/Windows-8/upgrade-to-Windows-8

    "8.1 for Windows system requirements.

    http://Windows.Microsoft.com/en-us/Windows-8/system-requirements

    @@@@@@@@@@@@@@@@@@@@@@@

    How to buy Windows 10:

    http://www.microsoftstore.com/store/msusa/en_US/cat/Windows/CategoryID.70036700

    But first make sure that you have the correct configuration and your computer manufacturer provides the right drivers for 10.

    https://www.Microsoft.com/en-us/Windows/Windows-10-specifications#sysreqs

    " System requirements Windows 10"

    https://www.Thurrott.com/Windows/Windows-10/3884/Windows-10-system-requirements

    Microsoft deploys Windows 10 available as free upgrade to Windows 7 features, Windows and Windows Phone 8.1 8.1 qualified. It will be available from July 29, 2015

    "FAQ Windows 10.

    http://www.Microsoft.com/en-us/Windows/Windows-10-FAQ

    See you soon.

  • I need ITE8708 device for studio xps 13 pleasssseeeee

    I need instul ITE8708 to my studio xps 13

    I am looking for the reader but I can't

    Please help me

    http://www.Dell.com/support/drivers/us/en/19/DriverDetails/DriverFileFormats?DriverID=CJ8FK&FILEID=2731109826&ProductCode=Studio-XPS-13&urlProductCode=false

    Works for me

  • Upgrade GPU for X51R2 options

    Here is my current setup:

    System model: Alienware X 51 R2
    BIOS: A07
    Processor: Intel Core i7 - 4790K CPU @ 4.00 GHz (8 CPUs), ~4.0GHz
    Card name: NVIDIA GeForce GTX 960
    Manufacturer: NVIDIA
    Track type: GeForce GTX 960

    The power of 330 watts supplied with my computer. Are there options for a GPU upgrade? I'm crossing this threshold GTX 970 so that I can use an Oculus Rift with this computer.

    Thank you!

    The GTX 970 will work, and to be honest, it would be the best option without having to make any changes.

Maybe you are looking for

  • Mid 2012 MacBook pro test equipment

    I got the error 4BAT/1/40000000: 0x8984fb90 while doing the test hardware. Can anyone advise if this is a question of logic board or battery? I checked in the coconut battery test and battery seems fine. I had this problem all of a sudden as I was ge

  • model of my laptop and HP Bios Update UEFI

    Hello, I have two questions (1) I can't find what model number, my laptop is so I can understand that downloads to download off the hp drivers and software update and I tried this auto finder without any results. It is a Pavilion dv6, I was sure the

  • Qosimo G20: Settings Wlan WEP is not possible running Config free?

    Hello!I have a G20 Qosimo running XP media center operating system.Default Toshiba ConfigFree is installed.Tried to find out how to set the WEP key, but try to do it in the configuration/network settings task was abandoned with a message.This message

  • How to turn off the lights under speaker on Satellite P100?

    I need to know if it is possible to TURN OFF the blue led underlight. (under the harman/kardon repro)laptop SATELLITE P100-387I dod not find it in Control Panel. Help, please

  • Error in the simulation: not enough nodes found

    Hello I'm trying to simulate a ckt simple active filter using MAX9618. However, I get the error message as not enough knots in my schema I join the scheme of reference. Can someone please help me understand why I get this error? If I remove U2B compo