Upgrade L-ASA-SSL-10 L-ASA-SSL-50

Similar Questions

• AIP - SSM upgrade for ASA active / active

  Hello world!

  I need help on improving the aip - ssm modules to E4 on two s asa who are active/active state. I'll be able to do this without downtime? What are the considerations?

  AIPs are independent of the resumption of the SAA, however, the SAA can consider the status of the AIP in passage of failover, which means it can failover

  If it detects a module AIP descending on the active device.

  The best method for upgrading in this situation will be the status of active failover Setup for all groups on the SAA primary, then upgrade the AIP of the ASA high school.

  Once the agreement in principle of the school is completely updated and functional, then set all groups to be active with the ASA failover secondary.

  Then the primary AIP.

  Once the primary AIP is completely level and working, you can then restore the status of the ASAs failover, by setting the active failover for the Group on the ASAs specific you want them to be active on...

  Kind regards

• Upgrade license ASA 5505

  Hi guys, currently I use basic ASA 5505-license and what I know are by default it supports only 10 VPN peer and plan to upgrade, so in this case, contact 2 of the seller, and they give me different about 10 peers, I 1 seller provide me ASA5505-SW-10-50 = and 2 seller provide me with L-ASA5505-SEC-PL =. so my question what part number, should I get if I want to spend 10 VPN peer? I thank in advance

  ASA5505-SW-10-50 = license only gives you more in-house bot users VPN-peers either. You need the update of the license more than VPN-peers SecPlus (L-ASA5505-SEC-PL =). But who will give more internal users if they are also too small. If you need increase these too, you need these two licenses.

• The upgrade of ASA 5520

  Has just received a new ASA 5520 and I'm trying to update the ASA s/w to 7.2 and the ASDM to 5.2. I copied the Flash files, but when I run "asdm image flash: / asdm521.bin ' I get an error that it is not an image file and I don't know where to start with the ASA. Any help would be appreciated. I can't find any info in my documentation.

  Try this,

  To update/install the ASDM follow the example of the procedure,

  ASA (config) # copy tftp flash

  Address or name of remote host [xxxx]?

  Source [pix704.bin] file name? ASDM - 504.bin

  Destination file name [asdm - 504.bin]?

  Access t... ftp://x.x.x.x/asdm-504.bin!

  !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

  Writing flash file: / asdm - 504.bin...

  !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

  !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

  5958324 bytes copied in 165,460 seconds (36111 bytes/s)

  ASA (config) #.

  ASA (config) # sh flash

  Directory of flash: /.

  7 rw-5437440 21:12:42 pix704.bin 24 November 2005

  5919340 - rw - 11 20:59:06 November 24, 2005 asdm - 504.bin

  -7017 rw-13 14:00:58 22 July 2005 admin.cfg

  ASDM - 504.bin is now copied into the flash. We should now set to use PIX

  This image to load ASDM.

  ASA (config) # asdm image flash: / asdm - 504.bin

  Final steps involve configuration running record in memory as we

  changes to boot files and reload the PIX.

  ASA (config) # write memory

  Building configuration...

  Cryptochecksum: d4f498de e877e418 2f9effa7 62ca0d6b

  4807 bytes copied in 3.20 seconds (1602 bytes/s)

  [OK]

  ASA (config) # reload

  Once the PIX comes back to the top, we can check that upgradation succeeded

  using the command 'show version '.

  Consult the ASDM upgrade procedure

  http://www.Cisco.com/en/us/customer/products/HW/vpndevc/ps2030/products_tech_note09186a00804708d8.shtml#T8

  I hope this helps... all the best... the rate of responses if deemed useful...

  REDA

• How to upgrade an ASA 5510/20

  I have several ASA 5510 and 5520 requiring an update and I tried to find a way to automate the process. Many of the features are running in active/active mode (primary is active and the secondary is in standby mode).

  I'm looking through the ADSM features and I found the automatic update. This looks like a good way to go because he downloaded the software for primary school and then transfers her back to the secondary device. It then performs the update device 1 both starting with the secondary device. But he said: I need a server was updated to contain the new software and I do not know how to create a. I have a machine that a FileZilla server is installed, but that uses FTP and the Automatic Updates settings are looking for an HTTPS address.

  The other option I havea Cisco first Infrastructure 2.0 is available. I can use this to manage the software, but there is nothing on how to use it with an ASA installation as an HA pair.

  I could use any help you may have.

  Cisco Security Manager is more generally used as a server update for large deployments ASA.

  PI 2.0 is a little rough around the edges on its support of ASA, and I would judge not quite ready for this task. (It is same with the package update of December 2013, which increase the support of the ASA).

  Depending on your version, most people are not comfortable with auto update of firewalls. Things have changed considerably with post-8, 2 and all migrations I've ever done that (TENs) involves a manual check of the new syntax and operations.

• Upgrade ASA5510 ASA/AMPS

  Does anyone have a detailed paper on how to improve ASA5510 of 7.2 to 8.0 in an active/passive configuration?

  Thank you

  Hello

  Watch http://www.cisco.com/en/US/docs/security/asa/asa80/configuration/guide/mswlicfg.html#wp1057338

  I hope this helps.

  Best regards.

  Massimiliano.

• We are upgrading Cisco ASA VPN HA pair 9.5.1

  We will lose the sessions/connections VPN?

  This is what happens when you do not have state synchronization.  Maybe you would like to enable for your next update.

• ASA 5505 SSL VPN license update

  Hi all.

  Our ASA 5505 with DATABASE default license allowing only 10 simultaneous vpn sessions (including 2 Anyconnect + IPsec). attached a TXT file with the license information. This Firewall is's use only for vpn access, and we less vpn tunnel vpn IPSec-L2L, anyconnect client SSL and IPSec client access configurations vpn to the top and race walk,.

  We are in terms of upgrading vpn license to archive IPSec 10 and 10 Anyconnect and 1 anyconect mobile VPN sessions in time. so my questions are;

  1. can I buy "ASA5500-SSL-10 =" accounting and to upgrade our ASA 5505 without having to buy "L-ASA5505-SEC-PL =" license of pus of security.

  2. asa use to upgrade only Anyconnect SSL vpn license while keeping 10 vpn IPSec comes with the base license.

  Thank you & you expects value comment

  Thank you

  JCK

  1. Yes.

  2.Yes.

  If you want to keep Clientless SSL VPN you do not want to continue with the addition of the ASA5500-SSL-10 = part. If you can do without client (including the conversion the two existing ones), more economically, you can opt for Security Plus and AnyConnect Essentials licenses. (US$ 800 vs price $1250).

  In both cases, the Mobile requires the AnyConnect Mobile (ASA-AC-M-5505) license.

• Upgrade ASA 5510 7.0 (6) 8.2 (5)

  Hi, I want to upgrade my ASA 5510 version 7.0 (6) 8.2 (5).  Read the release notes for 8.2 (5) it is said that the requirement of DRAM is 256 MB unless you have high CPU utilization. He also says that I have to upgrade through the main version of 7.0 (x) to 7.1 (x) and 7.1 (x) to 7.2 (x) and 7.2 (x) to 8.2 (x).  The questions are:

  -My ASA has 256 MB of RAM and 68% of free memory, if you think it will run version 8.2 (5) without any problems?

  -When you make upgrades to major releases, are there considerations concerning the configuration file? Or the versions to use for versions 7.1 and 7.2?

  -Would you recommend doing all the updates in a single window of maintanance?  How long might take?

  -It should not be a problem with 256 MB when you run version 8.2.x unless the SAA is in the way of a high traffic load. However, if you have decided to upgrade to version 8.3 and above all in the future, it requires certainly 1 GB of DRAM on ASA 5510.

  -There are minor changes to configuration of version 7.0 to 8.2. However, if you are running SSL VPN on version 7.x, then the customer should be changed to AnyConnect SSL VPN. However, if you have decided to upgrade to version 8.3 and above, there are major code changes.

  -I do not see a problem of upgrade under a maintenance window. How long it might take is something that I could not answer. It really depends on your environment and as you know with any updates/changes, it can go smoothly or can go horribly wrong, so I can't estimate on your behalf. If all goes well, I can't be too long, basically, download the software at the ASA, change the boot image and reload. And you have to apply to all the release mentioned in the release notes. Normally, I would estimate over shorter time (to give you enough time to restore, just in case it won't).

  I hope this helps.

• After ASA 7.1 (2) upgrade 8.0 (4) remote VPN is not working properly.

  I just upgraded my ASA from 7 to 8 and now, my remote access VPN working properly. The tunnels connect and I can ping anything, but I can't browse network shares or connect to Exchange.

  No idea as to what I'm missing?

  Thank you

  Dan

  IPSec VPN packets are removed when compression is enabled, when you configure the enable command ip-comp under Group Policy, then large packages that are eligible for compression are deleted in silence by the security apparatus. VPN compression is only useful for very slow Internet connections, so we suggest you disable compression (ip-comp disable). Alternatively, you can move on to build interim 8.0 (4.16) or later. (CSCsu26649)

  Release notes for Cisco 8.0.4.

• Upgrade of the ASA

  I have to upgrade the ASA. Can anyone suggest me that it will be better or I have to go to 9.x or higher version of 8.x?

  I saw a lot of caveats resolved to 9.x, but a few caveats still there. I'm not able to differentiate these that you warnings are dangerous for our network performance. Can someone tell me about this what warnings are more harmful?

  Kind regards
  Mukesh Kumar
  Network engineer
  Spooster COMPUTER services

  Hi Mukesh,

  Go with any of suggested ciscoes OS which is recent. But once again bugs are specific to certain services, and it varies in impacting the case to another.

  9.1.2

  9.0.3

  8.6.1

  the 3 versions above are considered to be stable versions... you can use this...

  Concerning

  Knockaert

  Concerning

  Knockaert

• ASA Anyconnect with PBR

  Hello

  We have a customer who upgraded his ASA to version 9.5.1 and now wants to use ACB for users connected by Anyconnect.
  Today, ASA is configured with an ACL filter which local networks is only allowed in the Tunnel.
  We tried to use the ACB in order to put all traffic through the Tunnel and the next another device on the side break LAN.

  AnyConnect Network: 172.18.18.0/24
  LAN network: 172.18.16.0/24
  Default to use for the anyconnect customer gateway: 172.18.16.202

  It was created an ACL standard for traffic of correspondence 172.18.18.0, a road map which next-hop is 172.18.16.202 and applied to the external interface.

  Gateway 172.18.16.202 knows that net 172.18.18.0/24 is on ASA (static route)

  It is my understanding no? I have configured as indicated above, but did not work.

  Kind regards

  Regis

  Hi Regis,

  If you want to send all Anyconnect traffic to a specific host on the LAN site (next hop), you can use the 'tunnel route' function instead of the ACB.

  Check more information below:

  http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-next-generation-firewalls/112182-SSL-TDG-config-example-00.html

  It may be useful

  -Randy-

• ASA-SSM-10 improvement no license or signatures

  I successfully upgraded our ASA-5510 with the latest version of the software.

  Our IPS module however ASA-SSM-10 seems to be the settings to factory default with only an IP address that is configured without any permission or certificates. The ASA-SSM-10 module can be improved with the lack of licenses or certificates? In addition, by using PuTTY I am able to connect to the ASA-SSM-10 module and ping the module and my laptop that I have connected via the management port. I am unable to ping from the laptop to the module of ASA-SSM-10 well.

  Continuing the investigation in addition to the configuration of the management port IP address there is no VLAN, GW, image url or ip address of the configured port. Is there a simple way to upgrade the software on the ASA-SSM-10 without affecting our two ASA - 5510 that are configured for failover?

  I suppose I can do up to a VLAN, GW and port address to get my cell phone to ping to the ASA-SSM-10 module to upgrade without affecting our ASA-5510 that are configured for failover. ***

  You can attach more licenses for the legacy IPS until April 26. But the question is whether it is worth spending time and money in the present. The IPS legacy is dead and you should focus on firepower for IPS. But who does not work on your hardware.

• LICENSE of BOTNET in ASA

  One of MY customer wants to upgrade their 5 qnty of ASA-5000 X series firwall with firepower.

  and they also wants to license BOTNET.

  My question is, is it mandatory (BOTNET) when you upgrade to ASA - fire power?

  Coz, we also take AMP, STROKE.

  and I was informed that the BOTNET is included in AMP power lic of fire.

  My question is, is it mandatory (BOTNET) when you upgrade to ASA - fire power?

  The subscription of BOTNET is separate and is not required for the upgrade of firepower. In addition, if the customer will get subscription fire power amp, then I would say that the subscription of inherited BOTNET would be unnecessary.

  I hope this helps!

  Thank you for evaluating useful messages!

• Filtering in Cisco ASA using module sfr Web

  Hello

  I have Cisco ASA 5515-x version 9.2 (2) and I use ASDM version 7.2 (2). I module 5.3.1 LICO of ASA. I want to activate the ASA web filtering feature. Previously, I used the method of expression regex in the SAA to perform url filtering, but it was not effective. Since then, I have the license for the management of firesight I want to use it.

  But I am confused as some cisco docs say to set the firesight management in vmware while others offer to run the boot image in the SAA itself. What is the right way to do it?

  The show module command, I see that my module of sfr is in place so that means the sfr module is pre-installed, and I can't do a lot of configurations?

  It would be better for me to run ASA itself, but if it does not work like that then I will configure in VM. So please me clearify that concerns my options and my best chance.

  If it should be installed on a virtual machine or ASA itself, then please give me the link to download the boot images and other files on cisco.com. I have the user name and password, but did not find the correct software.

  Thank you in advance.

  Your ASA 5515-x performs the minimum version required to support the fire power module (sfr). The module also runs the initial version of the software of the firepower for ASA-based module firepower.

  With this combination of Software ASA and firepower on your device, you will need to use an external administrator of firepower to manage module (create strategies, apply licenses, monitor events etc.).

  From ASA 9.5 (1) and firepower 6.0, you have the opportunity to make the most of the same functions via ASDM. You must upgrade the ASA (both ASDM) and firepower to achieve module.

  In both cases, you should Protect licenses and URL filtering for the module of firepower.

  The Quick Start Guide is here: http://www.cisco.com/c/en/us/td/docs/security/asa/quick_start/sfr/firepo...

  See also the excellent vidoe Lab Minutes guides for firepower: http://labminutes.com/video/sec/ASA%20FirePower

  The ASA and ASDM software is here:

  https://software.Cisco.com/download/type.html?mdfid=284143128&flowid=31442

  Software module of firepower is here:

  https://software.Cisco.com/download/release.html?mdfid=286271171&flowid=...

  To run the power of fire management center VM, the software is here:

  https://software.Cisco.com/download/release.html?mdfid=286259687&flowid=...

  All the links above require a username cisco.com entitled (support agreement) to download the software.