USB-6501 not seen by MAX

Similar Questions

• NEITHER USB-6501 not recognized by the system

  Hi all

  I wrote this simple application that writes and reads a SPI frame.

  My PC have Labview 8.5.1 and DAQmx 8.7.1 (the CD was provided with my unit NI USB-6501). Everything works fine.

  But now I need to distribute the application, and I need to run it from a computer that does not have LabVIEW.

  I installed the latest versions of the runtime of LV (8.6), and the 8.7.1, DAQmx software but the program crashes produce an error (code 200477).

  I tried to install a more recent DAQmx software (8.9 full, engine of execution of 8,9 only), but the situation has not changed.

  Also: I tried on two different PCs, and I launched MAX: one of them doesn't even recognize that a DAQ hardware is installed (even if Windows recognizes as a work device).

  Anyway, the two PCs return error 200477.

  Any help will be much appreciated.

  Best regards

  Is - this dev4 on the pc without LabVIEW? You can easily see the device name in MAX.

• Satellite U840-111 - Boot USB option not seen unless

  With the help of the Ultrabook I have prepared an "emergency" Ubuntu USB boot image (LinuxLive used to transfer a .iso downloaded to a USB device) on an SD card in a USB - SD adapter (the map is to a USB port, not the SD slot).

  It worked well.

  But when I restart the Ultrabook using F12 to see the Start Menu there is no text next to the USB option in the start menu (and if I select the boot option I see Windows start as usual).

  If I select the option in the Bios on the F12 boot menu to go to the Boot menu in the BIOS I still don't see any text on the USB line.

  If now, I re - feed and use F12 I now see "Mass Storage Device" (or something equivalent, can't remember) on the port USB line and the machine now boot Ubuntu on it (and I can see the file system on the hard drive).

  As far as I know, you need to enter the BIOS Setup, but do nothing) before using the F12 boot menu if you want to start on a USB (well this one at least).

  This seems to be a bug in the BIOS? BIOS version is 1.4

  Not quite sure if it s a bug or not.

  To my knowledge, the USB boot option to flinch F12 menu until a USB compatible and put up-to-date device should be plugged.
  This means that you must connect a bootable USB device to the laptop and then power the device and press F12 to get the menu.

  I also read that all the devices can be fully compatible so it would be really interesting to know if the same question is displayed using a bootable USB flash memory key you've tried a combination of USB SD adapter I could be possible that it is the problem here.

• USB devices not seen on Satellite Pro A60

  Hello

  I'm having a problem with my laptop Satellite Pro A60 running Windows XP Home: it is simply not to see all devices at all. Devices (USB, fan keys) are to be supplied with electricity, but I can find no trace of them on the computer anywhere. It is even not complain that they are not recognized - it's as if they were not there. I've uninstalled and reinstalled the drivers of hub USB root/controllers, but that has not helped.

  It is the latest in a string a glitches that can be helpful to know: a few weeks ago, the ATI Mobility Radeon 7000 IGP suddenly caused windows crash at boot time. I could just sort the problem by updating the bios and reinstall the ATI drivers (all toshiba). It is not of course the relevance, but after the bios update I also improved the 6 F-secure antivirus software. XX to 7.01.

  Usually, I try to get as much as I can by reading these forums but I'm not a guru of computing and on this one, I'm out of ideas - because Windows is not identify any fault, I don't even know what to look for on google... Someone has an idea?

  Thank you very much

  Philippe

  Hmm, you said that you have already reinstalled the drivers of USB controllers/root hub.

  But maybe you should try to make this again as a result of this procedure;
  -Disconnect all USB devices
  -go to the Device Manager and change the view to display hidden devices.
  -Open the tree of the USB controller and remove all controllers.
  -Restart the computer and wait until the OS has installed everything again.
  -Then plug the USB devices to the USB ports for laptop

  If this does not help, it would be desirable to recover the laptop with the Toshiba Recovery CD supplied.

  Good luck

• external USB drive not seen

  Hello

  I just bought a Readynas RN212 as a replacement for my Duo (v1). But the external USB drive (Toshiba 2.5 inch, ext3), that I used as backup for my Duo and always worked perfectly, is not recognized in the RN212.

  I have ssh - ed at the RN212 and did a manual mount: mount-t ext3/dev/sdb1/mnt which worked. The player ends up in/run/udev/data.

  Any idea what's going on?

  Kind regards

  Eric

  Hello espakman,

  This USB has data on the volume of your old Duo? If it is possible to format, use the NTFS system.

  If it contains all the data, it's that it may be preferable that you contact support for the RN212 so it can be verified from the backend.

  Kind regards

• USB-6501 on MAX

  Hello

  I have USB-6501. I would like to have simulated the device on MAX. However, MAX does not seem to offer a device that simulated for USB-6501. I guess that a device simulated for another device would be sufficient to simulate USB-6501. If this is the case, that would do the job?

  Thank you

  Daisuke Takeshita

  The PCI-6503 map will work for your needs as a simulated device? See:

  http://forums.NI.com/T5/LabVIEW/NI-DAQmx-simulated-devices-exception-USB-6501/m-p/554855#M260787

  -AK2DM

• Why USB-6501 does not install on Win7?

  We are in a process of migration of the old XP machine test system to the new system of Win7. All but got properly installed USB-6501. After you install LabView / DAQmx and connection USB-6501 windows could not find the drivers for this device (poster the exclamation sign on the icon of the device in devices and printers). MAX 4.7.4 detects either of the device. I looked for similar scenarios on the Forum OR and abroad and tried the solutions proposed. Nothing worked for me. I know the issue isn't with the USB-6501 material because it is functional on the old system. 4.7.4 MAXLE Win7 system detects a very well (GPIB-USB-HS) different USB device, but not for USB-6501.

  I hope someone can help us identify the problem that we have struggled with for some time. Here are the differences between shipments of software on two systems:

  Old system:

  OS - XP SP3

  LabView - 7.0

  DAQmx - 8.0

  VISA - 4.4.1

  MAX - 4.5 (detects the GPIB-USB-HS and USB-6501.) Status on 6501 LIGHT flashes continuously)

  New system:

  OS - Win 7 Enterprise

  LabView - 7.0

  DAQmx - 9.2.2

  VISA - 5.0.3

  MAX - 4.7.4 (detects only GPIB-USB-HS. Status on 6501 LIGHT flashes 3 times and then road)

  Germano,

  The device has been appear in Manager devices, but with the yellow exclamation mark for no drivers found/expenses. Update drivers on the property page does not help.

  So yesterday I spent most of the day removing all facilities OR according to the instructions, I found in this forum. Then I reinstalled the software OR in the order following, restarting after each installed:

  (1) LabView 7.0

  (2) DAQ 8.0.1

  (3) NEITHER-488. 2 (v2.30)

  (4) connected USB-6501 first. The installation of the device has gone well and is now detected to the MAX!

  (5) connected GPIB-USB-HS. Scanned for changes on the hardware, peripheral GPIB presents itself to the MAX, but with a weird name announcement its INF file on his behalf. See the screenshots below:

  GPIB device incorrectly installed:

  

  GPIB device properly installed:

  

  The strange thing is that this GPIB device was fully functional on my previous installation (see attachment max_report_3-23 - 11.pdf), now reinstall after its unusable (see attached max_report_3-24 - 11.pdf). Looking for GPIB instruments to help Max returns no result, but if I reconnect GPIB-USB-HS to the old system of PC all instruments are detected (for instrument scan error message see attached MAX after reinstall.jpg).

  That my new problem is not related to USB-6501, maybe I should open a new forum thread.

• I have the model of macbook air 2016 with i5 Professor and 8 GB ram... since it's the fastest ssd, but I have not seen all speeds up to now, I want to say is bcz I need to have usb 3.0 USB key or hard drive to see the speed of the ssd to usb 2.0 will work

  I have the model of macbook air 2016 with i5 Professor and 8 GB ram... since it's the fastest ssd, but I have not seen all speeds up to now, I want to say is bcz I need to have usb 3.0 USB key or hard drive to see the speed of the ssd to usb 2.0 will work

  What do you mean, your message is not clear.

• Error "device ID is not valid" USB-6501?

  Hello

  When I run the script "USB-6501 Control.llb Interactive", I have this error "device ID is not valid"?
  If you know another script that animates the "USB-6501" to check its lines, please help me?

  Best regards

  Right now, I don't have the time to look in the code example, you provided...!

  But why not use DAQmx functions OR DAQ Assistant to write code with whatever functionality you need...?

• To connect to the PC - tab 8W - not seen when connected via USB - Help!

  My new 8W tab is not seen by the PC connected via USB. Both are Windows 10. Help!

  Out of curiosity I will pick up an OTG cable and let you know the result!

• USB-6501 - impossible to find a basic example of Labview

  Hello

  I recently bought a USB-6501 card and I used it in my own succesfully end and C++ programs using the DAQmx drivers.

  Then I tried to move to Labview 2009 (I never used Labview) so I looked for a simple example.

  I tried to boot from the example 'interactive Control Panel' (http://digital.ni.com/public.nsf/allkb/AF0F31EE5D2AD23F862573140009D7C2?OpenDocument).

  I had to install the 'DAQmx Base' for him to start, as described in the previous link. now it begins (before Labview attempted to get a few missing .vi) but I get a message "error 200220 occurred at an unidentified locatio.

  Then I realized this example is 'old' (as explained here: http://forums.ni.com/ni/board/message?board.id=170&thread.id=209247), and it is suggested to look for a new one in example Finder ' entry-level equipment / output-> DAQmx-> Digital measurement (or generation)-> read Dig Port.VI.

  I tried, but along the way ' entry-level equipment / output-> DAQmx-> "only a folder named"Analog Measurement\Voltage"exists.

  Also in the search for 'Reading dig Port.VI' does not work.

  I've already spent many hours in this research and tent and the fact that I am not able to find not even a basic example, it is quite frustrating and it is making me give up the idea of using Labview.

  Please can anyone give me any suggestions where find/download an example simple and minimum to use my USB6501 in Labview 2009?

  Thank you

  Scipione.

  First, install DAQmx Base was a mistake. Uninstall it and then install the Driver-OR-DAQmx. The driver must be installed after the installation of LabVIEW. After installation, make sure that the device is listed in MAX under "DAQmx devices. If it is not, your installation is still not correct.

  To search for example LabVIEW, see help > find examples. Under Input and Output hardware > DAQmx, you will find the digital generation and numerical measures. You have to look at the simple, timed software examples such as read write dig Chan, writing Port to dig, dig chan, reading Dig Port. You also have the option to use the DAQ Assistant.

• Operation of USB-6501

  Hi all

  I have a brand new NI USB-6501, and I'm looking for more help with the operation.  I'm running OS X 10.11.1, LabVIEW 2013 SP 1, NI-VISA 15.0 and NOR-DAQmx Base 15.0.0.  I set up and plugged my module and get the flashing green light stable.  I ran NI MAX, found the module and renamed 'Motor_Module '.  Then, I went to my DAQmx Base of examples and found the Control.llb Interactive USB-6501 and ran the interactive VI control that is contained in this library.

  The first thing I tried was simply running the VI.  I got error-200220, device ID is not valid.  I changed the name of the device to "Motor_Module" and run the VI.  This time, I got error-200558, a task cannot contain multiple independent devices.  Create a task for each independent device.

  And here I am.  My ultimate goal is to have this output module signal collector type open to + 5 V.  Any help would be greatly appreciated.  Thank you.

  Hi Sullivnc,

  I would recommend you look at a few examples in the Finder for example of OR. Under input and output hardware, there is a folder for DAQmx who has a record for a digital output which has some useful examples. If you do continuous or left over, you can add more stuff to your code as a clear task DAQmx, vi DAQmx Timing, and/or vi DAQmx task is made.

• NI USB-6501 digital output problem

  Hello

  I use DASYLab v.11 and I'm working on an interface with the NI USB-6501 where I'm putting a digital high on four ports.

  With the module "NOR-DAQmx - digital input", I managed to read the digital inputs of the ' NI USB-6501 ".»

  It's only the "NOR-DAQmx - digital output" I can't go to work.

  Using 'NI MAX' of NOR I have easily can emmit my four LEDs in the way of my High/Low ports.

  But not with DASYLab. When you use DASYLab tension on the ports remains unchanged.

  Now, I have a switch module, generating 5/0, directly connected to the digital output module, which is assigned to my four output ports for my task.

  I also tried with a module of relay between the two without success. I also tried to use 1.5 above instead of 5 without success.

  I use the option 'Bus (0/5 supply) for the module "Digital output".

  "NI Max", I configured the ports as "active drive.

  Any suggestion of what I might be missing?

  Thank you

  Martin

  Hmm, four ports, or four lines?

  A port consists of eight lines. Each line can control an LED (ON / OFF ~ 0/5V).

  If you have created a task to dig-out to control a port, 5V to this port sending sets all lines of this port to 'high '.

  You need to 255 for each line one too high port (at the bit level: 128 + 64 + 32 + 16 + 8 + 4 + 2 + 1).<- eight="">

  Or, you can create a dig out tasks to control four lines of a specific port.

  Four lanes of the EEG DAQmx DigOut module.

  Each of the channels of the modul will feed a single line of the task/device.

  Four switches will then turn the lights, or turn off.

  Make sure, that the 'bitposition' is the number of correct line (see picture).

• Can I use a USB-6501 instead of a PCI-6503 map?

  I currently use a card PCI - 6503 DIO into a Windows XP system. We have an old (7.1) version of LabVIEW. We are looking for a Virtual Machine in Windows 7, but he will not be able to communicate with the PCI Bus. We currently use a PCI-6503. A USB 6501 will work to place it?

  We are looking for some intot wiring problems, but I think it will do the job.

  Thank you.

• USB-6501 Z (high impedance)

  I am using the IDW library to create a master by using the USB-6501. My problem is that the DAQmx write gives an error when it tries to use the 'Z' setting for high impedance. Are there workarounds for this?

  6501 does not support high impedance state... inexpensive compared to high-performance and you have a low cost DIO.

  Might be able to set the output to an entry, but there is still the internal pullup with that you will fight.