USB drives suddenly not recognized by Vista 64 SP2
2 USB drives that work on another machine to Vista (32-bit) are not recognized and do not appear in my computer, but appear in 'remove hardware safely '. These USB drives has worked in my computer up to a week or 2 ago.
When the disks are inserted a new item will appear in device ("storage volume") Manager who has a subelement ('generic volume') which has a yellow "!" which indicates a bad driver.
The readers appear in disk management, but any attempt to change the drive letter or view properties gives an error "operation has not completed.
Try to reinstall the drivers results in a message that the drivers are current, but the problem persists
Hello
Control controllers Control Panel - Device Manager - USB Serial - USB mass storage devices (you can have
more than one - If Yes check all) - double click on the driver tab - click Driver Details - the default is
C:\Windows\System32\drivers\USBSTOR. SYS (the C:\Windows is where you installed windows
If not C:\Windows\) you can't have one for your car if it not recognized - when it is recognized
and if doesn't work does not correctly return to this step.
Check again once you advance through them.
2nd check these:
Operating instructions: find 'lost' Windows Vista drivers when you add a new device
http://www.texxors.com/content/how-find-lost-Windows-Vista-drivers-when-adding-new-device
Tips for solving problems of USB devices - and a Mr Fixit
http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB
Hardware devices not detected or not working - Mr. Fixit
http://support.Microsoft.com/GP/hardware_device_problems
-------------------------------------------------------------
If no joy:
Make a Restore Point
Control Panel - Device Manager - click in the empty area - VIEW - show hidden devices
Now look everywhere EXCEPT the USB controllers for your device (cannot be found) and if you find
It RIGHT CLICK and UNINSTALL all. The device is your (s) or similar.
now go to the USB and UNINSTALL ALL controllers in the category, but the category itself.
APPLY/OK
RESET
This refresh battery USB and hopefully it will allow the unit to install.
Here is the similar procedure under XP, Vista is the same, except that we need to clear the specific device if present.
http://support.Microsoft.com/kb/310575
This is a utility to help you, but do 1 above.
USBDeview is a small utility that lists all USB devices currently connected to your computer, as well as all
USB devices that you previously used. Run Options and check the 1st three choices to see if one is there.
Try to remove all instances and restart then plug the drive.
http://www.NirSoft.NET/utils/usb_devices_view.html
--------------------------------------------------------------------
Check this box:
Start - type in the search box - Windows Disk - find Windows Disk Management on the list above.
Click - look RUN AS ADMIN to see if there is a letter assigned or a conflict of law or the
drive letter assigned is not the one you used to see. This may show of course not the
Road at all, it's just a check.
-------------------------------------------------------------------
http://www.Uwe-Sieber.de/usbdlm_e.html
Its complex however, the site has a lot of help.
And all this?
See also this thread and those it refers too.
http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/ff81438c-EAC5-4b38-8b89-d1a1dbe837f3
I hope this helps.
Rob - bicycle - Mark Twain said it is good.
Tags: Windows
Similar Questions
-
CD/DVD drive suddenly not recognized - under Vista Ultimate.
I have a HP Pavilion running Vista Ultimate. Recently it stopped recognizing my cd/dvd drive. The regedit procedure does not help, because I have no UpperFilter registry entry. Where should I go next? Is there a link that will take me to more useful information? I don't know how to get instructions for regedit go to "next steps". Thank you!
What is the link you are looking for?
-
PX1394E - 3 50 (500 GB HDD USB 2.0) not recognized by Win XP SP2
Hello. I just bought and traded because I thought the first was faulty, a PX1394E - 3 50 500 GB HDD USB 2.0 external hard drive that uses Fire Wire, USB. Now I ve tried all USB devices, to begin with it uninstailling everything on we / off on to just pluging it when we / off and it keeps saying be the devide was not recognized and it doesn't propperly (small box pop up bottem left of the screen)
Now Issve exchanged it once already, and he said that the unit was defective, but having exactly the same problem with two different cameras? This seems a little more bad luck for me.
If anyone can help, that´d be great.
-Dan
Hello
You have software of Regen with your HARD drive? I don't know if this can help, but check the Toshiba download page and you'll find a version for Windows XP Home edition. Maybe this will help.
-
USB drive is not recognized in windows vista
Title: drive letter assignment
I just bought a stick of memory of tdk, but my pc does not recognize it. Ive been in disk management and I tried to assign a drive letter (because there not), but when I right click and try to change it just gives an error to restart but I get the same error when I restart. How can I get around this. Device Manager only says: device not identified. Any ideas appreciated Ive been at this for a couple of hours now
Tony
Hello
Hello
I suggest to uninstall the controllers USB safe mode and then restart the computer in normal mode to see if it works.
Method 1: remove and reinstall all USB controllersTo remove and reinstall all USB controllers, follow these steps:
-Click Start, type devmgmt.msc in the start search box and press ENTER.
-Expand Bus USB controllers.
-Right click on each device under the Bus USB controllers node and then click on uninstall to remove them one at a time.
-Restart the computer and windows will install the rear USB drivers.
Check now if you continue to receive this pop-up.
Method 2: here's a Fixit tool. Run it to solve the problems with USB devices.Tips for solving problems of USB devices
http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devicesI hope this information helps you!
-
Art of STOR E external 1.5 TB hard drive is not recognized by Vista
I have a HARD drive that I brought in Europe, it was working fine and all of a sudden when I turn it on, is now telling me one of the devices USB has malfunctioned and windows does not recognize.
I can hear the HDD spining, and you can feel the playhead to move when you turn it on, would that be a driver or a firmware issue?
I have a lot of backup data about it as I can't afford to lose, then it would remove and put it directly into my computer to see if I can read it?
> I can hear the HDD spining, and you can feel the playhead to move when you turn it on, would that be a driver or a firmware issue?
You can try to connect to any other computer external HARD drive. If it would not then he s seems to be hardware problem.
Of course, it is s to connect the HARD drive directly to a HARD drive controller to see if the BIOS recognizes the HARD drive maybe it would be your last resort -
External hard drive WD not recognized by Vista
I have a WD 1 TB, external hard drive. It of, uh, was connected via my lynksys router. I recently had to start my laptop in an airport. During the startup, I got the standard message, of not being able to connect to all devices. I also had the standard dialog box for the connection in an airport, not safe, blah, blah. When I went home, my laptop does not recognize the WD drive. The other computers in the House to recognise that it is very good. If the signal between the router and the player is fine, but I can't connect to it. My laptop is about 18 inches from the router.
When you are connected, open center network and sharing, click Customize, then choose private, close.
-
Solution: The USB floppy drive is not recognized during installation of XP of RAID
Hello
This Solution is for notebooks Qosmio with RAID driver during (manual installation of windows)
I found the Solution to this problem,
[When you install Microsoft Windows XP by using a floppy drive USB on a player who]
requires a driver during the installation, the USB floppy drive is not recognized in all
installation. When Windows XP searches the driver of the second time, he will not be able to see
the floppy USB drive drive and prompts the user for the driver (RAID) again.
The installation will never reach this point. ]Solution:
This is a limitation of Microsoft, the Floppy Drive are do not appear in the file Windows 'txtsetup.sif.
Simply change the floppy drive in another brand and avoid Usb 2.0 external Usb floppy plus old 1 Try
Also note the back of drive sometimes they write (no bootable) avoid this alsoI personally Test this and it does not work it is "IBM Portable floppy drive" drive silver
P/N 27L 4226, FRU P/N 05K 9283 TEAC CORPORATION MODEL NO. FD-05PUBThe following USB floppy drives are listed in the file "txtsetup.sif" and are supported:
Device ID = VID: 057B and PID: 0000 for external floppy USB SONY drive, Sony 09K 9835 part number
Device ID = VID: 0644 and PID: 0000 for floppy drive to the external USB, TEAC, IBM replacement part number (FRU) 13N6752
USB\VID_03EE & PID_6901; Mitsumi USB floppy drive
USB\VID_057B & PID_0000; Floppy drive USB YEData, Sony part number 09K 9835
USB\VID_0644 & PID_0000; Floppy drive USB TEAC 27L 4226, FRU 05K 9283 IBM option part number
The following USB floppy drives are not listed in the txtsetup.sif file and are not supported:
USB\VID_03F0 & PID_2001; HP
USB\VID_054C & PID_002C; Sony
USB\VID_057B & PID_0001; YEData
USB\VID_0409 & PID_0040; NEC
USB\VID_0424 & PID_0FDC; SMSCIf you want manual of Installation of Windows Xp Media Center Edition 2005
then check out my discussion herehttp://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=16498
Thank you for the very interesting topic.
I think that it s an enemy of information all of you who have the same problem.Thanks ;)
-
Vista - usb ports are not recognized unknown device
Vista - usb ports are not recognized unknown device. any usb device it appears unknown. all worked a few days hardly, but after that I connected my Kodak camera - which does not, now, nothing works. Any help would be appreciated.
Hello
Thank you for using the Microsoft Windows Vista Forums.
Follow the instructions below that may help you resolve the issue.
Method 1:
Try to connect USB devices to a different USB port and check if you are able to access.
Method 2:
Click on the link below to run Fix it which will help you to solve the problem.
Tips for solving problems of USB devices
http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx
Click on the link below and install the update.
Rollup cumulative update for USB in Windows Vista Basic components
http://support.Microsoft.com/kb/941600
Try to connect the camcorder to the other USB port and on the other computer and see if the problem is resolved.
Method 3:
Let us try to disable the Antivirus security software and check the number.
Re-enable the security software after checking the issue.
You can also try disabling the firewall and check the issue.
Re-enable the firewall after checking the issue.
Method 4:
A clean boot helps eliminate software conflicts. Let us check if software is causing the problem by following the clean boot procedure.
To perform the clean boot procedure, follow the instructions in the link below.
Step 1: Perform a clean boot
Step 2: Enable half the services
Step 3: Determine whether the problem returns
Step 4: Enable half of the startup items
Step 5: Determine whether the problem returnsStep 6: Resolve the problem
Step 7: Reset the computer to start as usual
How to troubleshoot a problem by performing a clean boot in Windows Vista
http://support.Microsoft.com/kb/929135
After checking the problem, turn the computer back to the Normal mode.
Uninstall or update the program that is causing the problem.
Check whether the problem is resolved.
You can also check out the link below.
Please post back and let us know if it helped to solve your problem.
Kind regards
KarthiK TP
-
Satellite L10 - battery not recognized by Vista MS
Hello
I use MS Vista on my Satellite L10 and everything works great except my battery which is not recognized by Vista. There is just an unknown device in my equipment manager. In the section on the homepage Toshiba drivers I couldn't find a driver or other instructions. The MS Hotline told me this isn't their but question Toshibas.
I hope that this forum is someone who can help me solve the problem. I just want to know if my battery has enough power for 20 minutes or 2 hours and I really hate it if my laptop is suddenly out of power.
Thanks in advance.
ChristophHello
You have installed Vista on the L10?
Wow I know Satellite L10 is not Vista capable and you should be happy that this OS works without big worries on this Satellite phone.However, I recommend the Vista update to the last State, to install the compatible chipset from Intel page.
But I assume that the BIOS on this laptop is not fully Vista capable that this question therefore appears on the L10.
-
I'm on a computer laptop gateway and my cd player does not work all of a sudden. I can eject and put CD in there and it will hum for awhile, but nothing will happen. I went to Device Manager and it is not yet listed. I read the other topics and the problem is still not resolved, please help. Also, my HKEY_LOCAL_MACHINE folder has not all folders in there, so I can't go to system/etc to delete anything because there is nothing to remove. Thank you for your time
Hello
Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
This will refresh the default driver stack. Even if the reader does not appear to continue below.
Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
slight corrosion on the contacts (usually for a laptop) and other issues.Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr FixitThe CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
http://support.Microsoft.com/kb/929461When you insert a CD or a DVD, Windows Vista may not recognize the disc
http://support.Microsoft.com/kb/939052Your CD or DVD drive cannot read or write media - A Mr Fixit
http://support.Microsoft.com/GP/cd_dvd_drive_problemsCD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
http://support.Microsoft.com/kb/952951
Drive CD - R or CD - RW Drive is not recognized as a recordable device
http://support.Microsoft.com/kb/316529/Hardware devices not detected or not working - A Mr Fixit
http://support.Microsoft.com/GP/hardware_device_problemsAnother possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.Some DVD players do not use the Windows default drivers to check with the system manufacturer to see if there is a firmware or drivers for your if necessary.
Hope these helps.
Rob - bicycle - Mark Twain said it is good. -
I am trying to connect to Simple external storage drive and once I followed all the steps (only 2) Windows XP gave me a message that the USB device is not recognized or it malfunctioned. I disconnected everything and tried again in another USB port and still had the same error. I know that is not the usb port of my computer because I have it plugged into a port that just worked. I have Windowx XP SP2. Any help on this would be appreciated.
XP forums:
http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP
Link above is for XP Forums.
There is a list of the different Forums XP to the link above to help you.
You get the help you need there.
Here is the Vista Forums.
See you soon
Mick Murphy - Microsoft partner
-
AFTER reconecting LG; Sata CD/DVD drive is not recognized
Remember - this is a public forum so never post private information such as numbers of mail or telephone!
Ideas:
- You have problems with programs
- Error messages
- Recent changes to your computer
- What you have already tried to solve the problem
Hello
You mean an external USB drive or you've hooked internally? SATA is of course
normally internal unless you have it in an external enclosure. If internal why it did you
disconnected could lead to why it doesn't work now.If internal (are you sure that the disc is good - double check the wiring).
Follow these steps to remove corruption and missing/damaged file system repair or replacement.
Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN
sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlThen run checkdisk (chkdsk).
How to run check disk in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html==========================================================
After the foregoing:
References to Vista also apply to Windows 7.
Step 1: Please do all the same underneath if you did some before as is often total
a process that solves the problem.Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
below.
Then, work your way through these - don't forget the drive might be bad, could be a coward
cable or slight corrosion on the contacts (usually for a laptop) and other issues.Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr FixitTry this fix manually if the Fixit 314060 does not work
http://www.pchell.com/hardware/cd_drive_error_code_39.shtmlYour CD or DVD drive is missing or is not recognized by Windows or other programs-
a Mr Fixit
http://support.Microsoft.com/kb/982116The DVD player does not work after installing Windows 7
http://support.Microsoft.com/kb/975270/The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
Windows Vista
http://support.Microsoft.com/kb/929461When you insert a CD or a DVD, Windows Vista may not recognize the disc
http://support.Microsoft.com/kb/939052Your CD or DVD drive cannot read or write media - A Mr Fixit
http://support.Microsoft.com/GP/cd_dvd_drive_problemsCD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
Setup after booting from the DVD (AHCI)
http://support.Microsoft.com/kb/952951
Drive CD - R or CD - RW Drive is not recognized as a recordable device
http://support.Microsoft.com/kb/316529/Hardware devices not detected or not working - A Mr Fixit
http://support.Microsoft.com/GP/hardware_device_problemsAnother possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
manufacturer of device to see if there is a firmware or drivers for your drive if necessary.===============================
Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
do it right.Did you follow the Troubleshooting Guide for the reader who still does not work? There are
the entries in registry that the troubleshooter does not solve and those who "might" be the cause.Check with your Maker system and a device for the two possible firmware updates and the
correct registry entries for your car.Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
the parameters.HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
-----------------------------------------------------------------------
You can probably find more info here and maybe even the exact registry settings for your
CD/DVD drive someone with the same model.Forums - a lot of expert real help
http://Club.myce.com/CD/DVD units
http://www.myce.com/storage/Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
nothing change) - find the DevManView device and then make a right click on it free in RegEdit.DevManView - free - an alternative to the standard Windows Device Manager, which displays
all devices and their properties in flat table, instead of the tree viewer
http://www.NirSoft.NET/utils/device_manager_view.htmlI hope this helps.
Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.
-
Satellite A200 PSAF6A - HARD drive is not recognized. No recovery of product
The drive HARD in my Toshiba Satellite A200 PSAF6A-0US01N is not recognized in the machine or any other computer, so I can't run any windows/toshiba repair.
I know that readers have a factory reset hidden on the disc and press 0 to the power upward, but with the unreadable disk, how can I repair my installation of Windows Vista?
Hello
If the HARD drive is not recognized by the BIOS or other laptops, then I would say that your HARD drive is defective.
In this case, you need to replace the HARD drive.
In this case, you will not be able to start the recovery procedure from the HARD drive because it works badly as he has already saidAre you from the Australia? If you need a recovery disk, I recommend contacting the local Toshiba ASP to get this drive
-
Re: CD/DVD drive is not recognized correctly on my Equium P200
I recently bought a laptop P200D and now, I found that the CD/DVD drive is not recognized.
In Device Manager the drive icon has a yellow on exclamation and in the wealthy area it says "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) »
I tried uninstalling the drive and then to restart the laptop but it is has not been successful. I recently downloaded and installed the Service Pack 1 for Vista and I have read that there have been problems with device drivers and wonder if there is such a body?
Are there updated drivers available for this device?
Thanks for any help you can give.
Lester Mortimore
Hello
Check this thread http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=113742 please
I hope this will help you.
-
Was not aware there is a problem until I tried some recently audio and data CDs. Have you tried different Web sites to help you, however some of the directions come with a warning that by following certain procedures I can create other problems. The FixIt tool was not able to install the player.
Hello
Please ALL these even if you've done it before as it's often the total process that
solves the problem. You should also check with the system manufacturer as some readers do not use windows
by default the drivers and need their own, use the bottom and if no joy check on the site of the manufacturer of the system.Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
This will refresh the default driver stack. Even if the reader does not appear to continue below.
Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
slight corrosion on the contacts (usually for a laptop) and other issues.Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr FixitThe CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
http://support.Microsoft.com/kb/929461When you insert a CD or a DVD, Windows Vista may not recognize the disc
http://support.Microsoft.com/kb/939052Your CD or DVD drive cannot read or write media - A Mr Fixit
http://support.Microsoft.com/GP/cd_dvd_drive_problemsCD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
http://support.Microsoft.com/kb/952951
Drive CD - R or CD - RW Drive is not recognized as a recordable device
http://support.Microsoft.com/kb/316529/Hardware devices not detected or not working - A Mr Fixit
http://support.Microsoft.com/GP/hardware_device_problemsAnother possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.Hope these helps.
Rob - bicycle - Mark Twain said it is good.
Maybe you are looking for
-
Migration assistant will consolidate iPhoto and photo libraries
I just bought an iMac "towards the end of 2015" to replace my iMac 2011. I'm a Mac (MacBook Pro and iMac) user since 2005 and I am aware of the installation of the Migration Wizard when you first install a new Mac. However, for some reason, I have an
-
Primary control loop and loop DIO
Hello I use an X-series with Veristand 2011 card. I need to acquire some AI and DI whole. It seems that the AI will be supported by the main loop, which is very good for our goal for now. But what of the DI. Looks like the DIO loop works like a rate
-
There is no available on HP pavillion s3707c network adapter
I am trying to solve a problem with a HP slimline s3707c desktop PC. It worked a few days previously. NOW, I can not access the internet. Error messages stated that there is NO network adapter installed. I also States that a driver or drivers may
-
Hello I belong to a forum and requested notifications by e-mail. He managed for centuries. She didn't a month ago and I finally reset my computer. Now, it happened again. What I have to do the same thing? Anyone know why this is happening please? I c
-
Problems after the automatic update from Microsoft Outlook
A about having Microsoft automatic update, Outlook on Vista has stopped working properly. I can open the program, write an e-mail or two and may be able to send a mail, then the program freezes. It happened just after a update to day to day. How can