USB6008 as a VISA device

Similar Questions

• VISA devices with the same serial number and the vendor ID does not work (0xBFFF003A)

  Hi all

  I need to acquire the data of two meters of power YOKOGAWA with VISA driver (USB connection).

  They work very well if used alone, but they do not work when are used toghether. In particular, when I plug in and turn on the two of them, NOR MAX shows me the following error message:

  0XBFFF003A (VI_ERROR_INV_SETUP)

  viFindRsrc return 0xBFFF003A (cannot start the operation because the installer is not valid (because of attributes defined in an inconsistent state).)

  Please make sure that VISA is properly installed on this system.

  Possible causes of this error:
  1. more than one passport may be to attempt to claim the same resource.  You can try to disable passport to understand which Passport is the cause of the error.
  2 you have connected multiple no configured plug-and-play devices that have the same name of the resource. For example, the vendor ID and the serial number may be the same.

  In fact, according to MAX, both power meters have the same serial number and the same vendor ID; so, this seems to be the reason why they do not work together.

  Can someone help me?

  Thank you all

  
  

• NI-VISA takes a unique I.D. number for each USB device?

  Hi all

  I'm relatively new to LabVIEW and VISA Toolbox.

  When you communicate with LabVIEW and a USB via VISA, VISA shoots a D.I. unique number for the USB device for each connection established?

  I have reference: http://www.ni.com/white-paper/4713/en

  Kind regards

  Bryan

  Bryan,

  I don't understand what you're saying, so let me rephrase my answer and see that if this may help you - IF your device properly implements the USB standard and has a serial number, VISA uses this serial number.  If your device does not implement the USB standard correctly or if it does not have a serial number, VISA will do for you.

  If your device has a serial number, the VISA can be used to communicate with it.  There are routines that detect and identify VISA devices connected to your PC.

  JasonP

• Find resources VISA does not display my USB/GPIB device

  Hello

  I'm using LabView 8.0 with MAX 4.2.1.3001. I try to communicate with a former HP8563E Spectrum Analyzer with a GPIB to USB with VISA vi device nothing helps. When you try to find any valid VISA device with the vi 'VISA find resource' no device is returned. Can anyone offer any suggestions?

  -Chris

  Finally, I'll be back around him and the VISA drivers were not installed. This me baffled because in the latest versions of LabView, as 6.0, screws requiring some drivers (like writing serial port) were not available unless the associated drivers have been installed. Perhaps this philosophy has changed in more recent versions. In any case, thanks for your help

  -Chris

• Satellite A50-109: need drivers for Vista

  Abdoulaye all body...

  where can I find drivers for Vista...

  my PC is 'Satellite A50-109'

  Hi Alzaabi

  I wish that you check different threads here in the forum before opening a new topic of Vista drivers.
  Someone posted this link to the document from Toshiba:

  Windows Vista Driver Support for Toshiba laptops models
  http://support.toshiba-tro.de/KB0/TSB7201SK002HR01.htm

  As you can see the A50 is not listed ;(
  Therefore, you should check the various unique drivers of another series or visit device manufacturing sites to get the driver for vista
  Good luck

• serial port after the installed DSC module problem

  Hello..

  I want to GSM(with labVIEW) and PLC interface, My PLC will work in serial port only.

  In my PC, I have 3 serial ports. before installing the DSC module in my system, I can configure the ports series all the... but, when I finished installation of the DSC module, 2 ports is not between these 3 serial ports. Before PRECAUTIONS, I can work with PLC and I can use other ports. After installation, I can't configure the serial ports... Hereby, I have attached the error with this...  Please help me soon...

  The Solution is, no need to install the VISA device drivers separately. Installing the DSC module only.

• No material listed in Labview 2010 Linux DAQ

  Hello

  I have a problem with DAQmx Base 3.4.0 under Linux:

  mxbaseconfig shows my NOR-6009 device to the USB port. I can also create tasks corresponding to the nor-6009 in there. When I try to create a task in Labview 2010, one of the constant I/O are always empty. Dropdown menu arrow is grayed out. If I get the name of the device directly in the constant, he through me an error :-( Do not know Semms like Labview, which DAQmx Base instruments are connected...

  With devices VISA, I don't have this problem. All VISA devices are displayed in the dropdown of the constant and work correctly.

  lsdaq gives me:

  --------------------------------
  Detect of National Instruments DAQ devices
  Find the following materials:
  NEITHER 6220: "Dev1" (PXI1::4:INSTR)
  OR USB-6009: "Dev2' (USB0::0x3923:0x717B:0119B3BD: RAW)
  --------------------------------

  I use

  RedHat Enterprise Linux 5.5

  NI - 488.2 - beta - 2.51 b 1

  NI-VISA - 5.0.0

  NOR-DAQmx Base 3.4.0

  LabVIEW 2010

  All installers worked well...

  No idea how to access my OR-6009?

  Felix1234 wrote:

  It the device port ID is connected by a string variable to the Vi DAQmx Base... also works perfectly for me. But I do not know why the variable I/O noit work...

  DAQmx Base does not have controls that LabVIEW as DAQmx done [1]. Because the driver does not use background services, it cannot be said LabVIEW what devices and channels are available on the system.

  [1] NEITHER-DAQmx Base tasks and physical channels are not listed in the task of LabVIEW and string constants and controls
  http://digital.NI.com/public.nsf/allkb/57393FEDF313E99B86256F0B0010AD2D

• Error with Visa and USB device

  Hello

  I am currently working on a VI to use visa to get information from a USB device. The device is a digital-line tachometer.

  I was able to get the drivers USB and everything set and the device appears in MAX, but now I get an error after the open block of visa, and I don't know why.

  Any ideas would be greatly appreciated, but I don't know that anyone will be able to do, because you probably don't have the same one.

  VI is attached

  
  

• Comm port not detected by VISA / MAX after the device power cycle connected

  I have a device communicating via USB virtual comm port. The device and labview program both work very well, most of the time. The program is designed for the automatic connection for the connected equipment. It works perfectly when I unplug and reconnect the USB cable.

  However, if the unit power cycled as the USB cable is connected and the program/vi is running of things go wrong. The device enters a phase of boot loader for a few seconds to the power upward, if labview tries to query the port comm during this phase the comm port is corrupted in some way and is no longer recognized by VISA / NI MAX. However, other programs, hyperterminal, etc device manager can see and communicate with the port when the boot loader is complete. For Labview / NI MAX to see the port I have to physically disconnect the USB cable. The program does not need to be restarted in order to detect the port comm again and, infact, labview is restarted or my compiled program does not solve the problem. Physically disconnect the USB port allows visa / MAX OR see the port is connected.

  It seems to me that there is a problem with VISA where somehow if a device is not correctly identified by VISA during the first attempt it just does not take into account the port until a physical intervention. Is there a way to force VISA to reassess completely all connected comm ports?

  Hello MJanus,

  As far as I know, most of the virtual com ports are not fully supported by VISA so some quirks in its operation are to be expected: http://digital.ni.com/public.nsf/allkb/6E1922B526572CB8862571AA00544057?OpenDocument

  Officially, we do not support the use of com virtual ports, if unfortunately, the feature you have now is probably as good you'll be able to get with this configuration. I know it's not the answer you were hoping to hear and I apologize for the inconvenience, but it is not really possible visa work well with all software virtual com port due to the wide variety of products available.

  Kind regards

• I use VISA 5.3 for reading my serial device... my standard equipment is WELL this device will send four messages for only one comand I need all four messages to display at the same time in VISA SERIES READ BUFFER

  I use VISA 5.3 for reading my serial device... my standard equipment is WELL this device will send four messages of single command given to this instrument... and I read messages through VISA series READ... during the race, the VI buffer displays the messages individually...  I need all four messages to display at the same time in VISA SERIES READ BUFFER, in order to find more than this block, I should add from the palette of function.

  Disable character of endpoint detection or make four readings where you concantanate simply the strings together.

• Visa resource unavailable, device to use my other program

  Hey guys,.
  I bought a Usb to parallel Port adapter and created a pilot nor Visa for him and then launch labview and I ran some programs on the card and everything worked, I was able to send data to the usb port and able to light a led and turn off... then later, I have restarted my laptop and when I run the application again labview to communicate with the usb it keeps giving me error timeout... I have change the same still d usb port error... I opened MAX to check on the device... It was as if the appliance is used my another program that does not allow for my labview program to contact him, I try to disabled my antivirus is giving the error of time-out, the device is used my request a new one and when I try to remove the device with windows I get this windows d device error is always used my request another... Later, I unplug the usb and plug it into a different pc labview only for the same problem from happening again... someone knows how I can recommunicate with my USB and say stop error timeout... Thank you

  
  

• VISA: (Hex 0xBFFF0011) insufficient location information or the device or resource is not present in the system.

  See the other post on this subject, but my situation appeared a bit different (http://forums.ni.com/t5/LabVIEW/VISA-Hex-0xBFFF0011-Insufficient-location-information-or-the/td-p/69...

  My device manager says that the device is functioning correctly, MAX also tells me that the device is working properly, but I still get this error when I try to open a panel of test VISA in MAX or log VISA in labview.  When I click on validate in MAX under port settings that she even says that he opened a successful session of VISA.  But it does not connect in the Panel test VISA or in labview.  See the screenshots below.

  No device manager said that all was well with COM1, see the pictures attached.  I was able to get this working to uninstall the device and the removal of all the drivers and reinstalling.  Don't know what the problem was, but from the entire apparatus of zero was able to fix it.

• NI-VISA 5.3 driver Wizard does not support USB 3.0 devices

  Hi all

  It seems that NI-VISA 5.3 does not support USB 3.0 devices. When I try to use the driver Wizard to create a driver for a USB 3.0 device, I get the error "ERROR-1073807178: device descriptor error - value not valid bMaxPacketSize0 (must be set to 8, 16, 32, or 64 bytes). I noticed that the unit has been giving wMaxPacketSize0 of 512 (2 ^ 9). But the driver Wizard treats the value 9. So I think that Assistant driver does not support USB 3.0 devices. If someone could confirm this?

  Thank you very much in advance!

  Jackie

  Hello Jackie,.

  Unfortunately, USB 3.0 is not officially supported in VISA 5.3 when you use VISA Driver Wizard.

  A non-official solution is to work around the "information in the descriptor' by selecting 'Other' in the list of devices. You will need to manually enter the 'USB manufacturer ID (vendor ID)' and 'type USB (Product ID) Code. You will then need to find your driver in Windows Device Manager, right click and select "update driver software". This, however, is not a workaround solution guaranteed as NI-VISA 5.3 is not officially compatible USB 3.0.

• VISA, GPIB read all device settings values

  Hello

  Y at - it a specific order of VISA or GPIB to read the current state of a device? I don't know the status byte.

  What I'd like to see is the present value of all parameters of the device, in order to be able to reproduce the same situation, other times.

  Is this possible with a standard command? Or is it related to a specific order of devices?

  Thank you

  This is something that is totally dependent on the device.

• LabVIEW - device COM of VISA - how to use the Hex Protocol to receive data

  Hey everybody!

  I am fairly new to LabVIEW and data collection, so maybe it's a pretty easy question.

  I want to read the data from a device Extech Instruments HD755, it is connected via USB to a COM Port.

  I can see the device at MAX and I am able to open the Panel to test VISA.

  I simply do not know what command I send now, either, I know how to do a Google search for this (I tried several commands, but they did not work).

  I have attached the Protocol of Communication of Extech and my first try of a VI.

  Thank you very much in advance.

  Tobias

  Cannot open your vi, I lv2011

  Communication protocol does not say what commands to send. If no other information is either trial and error, or ask manufacturer for example in any language of the text, it's easy to order if that is the problem.

  I try something as attached as a first test, maybe you would need to send several commands (0x04 then 0x01) before it starts the transmission