Use of the UC IPS

Similar Questions

• Can I use private as Source IPs from a remote network IP addresses while building the IPSec tunnel?

  Can I use private as Source IPs from a remote network IP addresses while building the IPSec tunnel? If not why? If so, how?

  Your explanation is much appreciated.

  Hi Deepak,

  In such a situation, you usually NAT traffic that goes to the internet, but exempt traffic that goes through the VPN, because it will be wrapped in packages with public IP (tunnel) addresses. You can use the same IP address on your interface in the face of internet for the NAT/PAT and source of IPSEC Tunnel.

• danger of the use of the Internet Routable IP space on network internal

  Hello

  We have a 16 IPv4 space which is recorded for us. For years we used these network on our internal network. We have layers of security separating the internal networks of the internet.

  Recently I was asked about best practices and security using the internet routable IP on my internal network. Can someone explain to me what threat posed by really?

  Thank you

  Dan

  Hi Dan,.

  One of the fundamental principles of the internet was to provide end-to-end connectivity. NAT killed this idea but with IPv6, we have 'enough' address space public to make it workable again.

  If you want security uses a firewall/ids/ips. Private addressing is not safer, anyone who tells you otherwise must have his head in the sand! :) Of course private address protects you from the outside
  recognition, but once one of these servers on private address that you have exposed to the internet through port forwarding or NLBs is compromised then the false confidence in security RFC1918 is eroded, as an attacker can start hopping around your internal network... and regarding your users emails offering £££ of unclaimed funds Bank Nigerian and hovering content compromise opening flash...

  Protect your network from the internet, your servers to your users and your servers to your servers!

  The University where I work also has a 16, and although we now go to addressing more private because we have exhausted our share (!) and moving private allowing for aggregation of the good path and one model simple address.

  see you soon,

  SEB.

• help with the new IPS file format

  I'm in IOS (1801-fixed) 12.4.9T that uses the sdf format. I'll probably not upgrade the IOS for awhile.

  Can someone advise if Cisco will continue to make available upadtes IPS to the sdf format?

  Thanks in advance for the forum entry.

  Cisco will continue to support the IOS IPS signature format 4.x based SDF files (for prior release IOS 12.4 (11) T) until June 2008.

  Thank you

  -Chris

• How to activate the two IPS on VCS starter pack express

  I have the Starter of Cisco Express works with a single IP address using a NAT. This only works inside the LAN. To enable this machine on the internet, I bought the key option to double network interface. I enabled both interfaces, but I don't know how I should configure the two IPS by access from the internet. I tried to activate the static NAT, but it did not work.

  There is only a single default gateway and this is where most of the traffic will be released and which should point to the internet router.

  If you have addresses of internall more than 'LAN', you can simply add additional routes via the administration console.

  As if LAN is connected to LAN2 192.168.150.0/24 and you 192.168.175.0/24 your home and where your laptops

  router for tha is 192.168.150.1 you would add that, on the road to xcommand, add the command:

  xcommand RouteAdd
  *h 'xCommand RouteAdd'
  "Adds and configures a new IP route (also known as a static route)."
  Address(r): "Specifies an IP address used in conjunction with the prefix length to determine the network to which this route applies."
  PrefixLength(r): <1..128> "Specifies the number of bits of the IP address which must match when determining the network to which this route applies. Default: 32"
  Gateway(r): "Specifies the IP address of the gateway for this route."
  Interface: "Specifies the LAN interface to use for this route. Auto: the VCS will select the most appropriate interface to use. Default: Auto"
  

  for the example given, it would be (user admin via ssh):

  xcommand road add an address: 192.168.175.0 LG: gateway interface 24 192.168.150.1: LAN2

  But to be honest I'm not sure jabbervideo it works well with the highway espress in

  a lan environment double anyway.

  As with a vcs - c / e deployment you have the model of the internal and external with vcs

  different hosts where he tries to get funding and then depending on who gets the data

  for the record. It may be that in any case only get you external IP of the vcs-e.

  I would therefore simply deploy a DMZ where the outside and inside can reach the starterpack with

  the same address or even external ip using a NAT that is hosted in LAN1 put directly on a public ip address in a dmz...

  

• How to monitor the use of the Internet (web) with installed PIX

  Hi all

  I hope that you could recommend an appropriate solution to the following situation:

  I have a client who would like to be able to occasionally monitor how his team uses the Internet - essentially the sites they visit and how much time they spend on these don't sites... no detailed report would be necessary, only occasional monitoring. Obviously, their PIX 501 must be the source of information... I guess that there is an app out there (commercial or freeware) which would collect & analyze the logs of PIX and translate them into a form that is easily understandable and advise the use of the Web.

  All recommendations / advice will be MUCH apprechiated!

  Thanks in advance,

  Sean

  It does not solve the DNS and it connects on the WHOIS database of reports to resolve outside IPs, you can set how long to keep the Cache DNS TTL (helpdful with internal clients of DHCP). If you access the web site, they show a sample report on request. You can customize reports to show a specific traffic/events. Also, you can analyze the traffic for individual IPs and each report has links to explain the Syslog events. You can have the report sent on an hourly basis.

• The use of the battery has increased since the update to ios 10. Also, why can not disable the voice command. It's the most boring on the new update.

  The use of the battery has increased since the update to ios 10. Also, why can not disable the voice command. It's the most boring on the new update.

  Depending on what you mean by "voice command", either:

  Settings / general / accessibility / VoiceOver / OFF, or

  Settings / Siri / OFF

  As for your use of the battery, you can check what app pulls most of its use in the settings / battery.  A new version of the app is sometimes problematic, not necessarily iOS or iPhone.  If you see a unusual % of use of a particular application, or force-to leave it removal/reinstalling it or remove it until an update comes.  If anything seems unusual, it might be a problematic installation of iOS, in which case, you could backup your iPhone and restore it:

  Restore your iPhone, iPad or iPod touch from a backup - Apple Support

• "No cell coverage" not listed in the use of the battery

  During the audit of the use of the battery parameters, on an iPad 2 Air, WiFi and cellular, upgrade 10.0.2, 'No cell coverage' is listed and uses a lot of battery percentage. This never happened since the purchase of the iPad two years ago. I've recently updated to iOS 10.0.2 and T-Mobile as the cellular carrier. This occurs when the two Wi - Fi AND cellular data are turned off. I barely use the cell service as it is, first of all just use wifi, and I never leave the cellular data connection on when you do not. I noticed a few days ago a T-Mobile "Carrier Update" has been pushed to the iPad. Someone else with the same situation?

  Hi there, stumped127! Thank you for using communities of support from Apple!

  Use of your iPad 2 Air indicates that it is looking for service even if you have data Wi - Fi and cell phone turned off after update to iOS 10.0.2. Given that mobile data is off, it shouldn't have an impact on the battery and I will be happy to help you with this. Be sure to test after each numbered step.

  How to back up your iPhone, iPad and iPod touch --before troubleshooting a device, I always recommend a fresh backup. It is preferable "to have" one to the 'need' to a backup.

  1. forcing a nearby app on your iPhone, iPad or iPod touch - first, quit all running applications, and then restart your iPhone, iPad or iPod touch - never underestimate the power of a good restart.

  2. reset the iPad settings - do not forget to write your networks, Wi-Fi/passwords before you start. On your iPad, go to settings > general > reset > reset all settings. This step returns your iPad to factory default settings. Test and if that solves the problem, use your backup to restore your settings.

  Take care!

• Sierra Messages App is forcing the use of the discrete GPU

  Since the update of my mid 2015 15 "MacBook Pro to Sierra, Messages.app requires the use of the discrete GPU and kill my battery time.

  All the world fell on this and if so, have you found a solution?

  Here, even with a MacBook Pro in early 2011... problem seems to be based on the new 'features messages"that you can use in iOS 10.

  From messages app, the internal GPU is used until I get a message with one of these new features to messages. Then the GPU will switch to the discrete GPU AMD and continues to work with him until I left messages app.

• iPhone7 +: what type of glass is used in the display

  I tried to find in the description of apple for the new iPhone7 tech + but see no mention of the type of glass used in the display. Where can I find info on it?

  Type of glass

  Notation for the scratch resistance

  Rating for break resistance

  Hoping it's the sapphire glass, but if it is not mentioned, probably same glass as previous iphone6s +.

  Thank you

  Speculation is prohibited by the Apple Support communities terms of use.

  If it is not in the specifications, we have no way of answering this question.

• How to make a refund on an app that I bought by mistake I can not use in the United States

  I have Down loaded and bought an antenna app companion that can not be used in the United States for $2.99.  How can I get a refund

  Purchases are considered final, but you can try the page 'report a problem' to contact iTunes Support and see if they will refund or credit you: http://reportaproblem.apple.com

  Or you can try to contact iTunes support via this page: https://support.apple.com/contact or https://www.apple.com/emea/support/itunes/contact.html

• Any possibility using only the built-in GPU?

  Mac OS X 10.11.6

  MacBook Pro(Retina,15 ",2015 mid)

  With graphics cards AMD one dedicated

  I wonder if it is possible to use only the GPU integrated while playing games. Cause I discovered that some games are no need to use the AMD GPU, but it is automatically switched to the dedicated GPU and drains the battery.

  Hope there is a solution for this problem. Thank you!

  It is somehow a conditional scenario suggested in this article

  on how to make some graphics settings may remain in service, here:

  • Set performance on MacBook Pro - Apple Support chart

  • MacBook Pro: how determine what GPU is in use - Apple Support

  {These links seem to show older versions of material your model}.

  Don't know if there is a way hidden within the system to change the default to

  stay on the one you want to be the first choice; Maybe in the command 'terminal '?

  In any case...

  Good luck in this case!

• Touch digital can be used on the iPhone 6?

  Touch digital can be used on the iPhone 6?

  Hello

  Touch digital can only be sent and received on Apple Watch (any model).

  Apple Watch requires iPhone 5 or later.

  More information:

  Use the touch-Apple Support

  Set up your Apple Watch - Apple Support

• A Mac mini, purchased in the UNITED Arab Emirates can be used in the USA with only change the power cord?

  A Mac mini, purchased in the UNITED Arab Emirates can be used in the USA with only change the power cord?

  Yes.

  http://www.Apple.com/Mac-mini/specs/

  the voltage may vary from 100-240 V AC.

• Use of the battery by app is no longer visible

  When my iPhone was brand new I used to see the use of the battery by app, but the small blue clock next to the "use of the battery" icon in settings/battery disappeared after a week or two. How do I get it back?

  How many minutes he normally brings to see app use? It looks like half an hour is not enough.

  I have the latest version of the system 9.3.4.

  The first thing to try, if you have not already, is a reboot or a forced reboot:

  Restart your iPhone, iPad or iPod touch - Apple Support

  If this does not help, then a backup/restore may be in order:

  The backup of your iPhone, iPad and iPod touch - Apple Support

  Restore your iPhone, iPad or iPod touch from a backup - Apple Support

  If this does not help, you may need to reset as a new device (which will lose your settings current, data, etc.):

  How to clear your iOS device and then set up as a new device or restore from backups - Apple Support