Using NAT to access remote vCD 5.1

I'm trying to get a unique virtual machine that is on my internal VCC 192.168.9.X subnet to able RDP (use it as a box of management). Previously on vCD 1.5, I simply created a NAT mapped 192.168.9.1 (internal) to 10.254.254.1 rule (external) and IP Masquerade enabled, and then I was able to RDP inside. However with vCD 5.1, I created a SNAT and DNAT rule mapped both to each other and I am unable to RDP into the machine.

If someone got it works?

Hello

I added a third post that shows how to access a Web server inside a paralytic and an RDP connection to this

http://www.gabesvirtualworld.com/VMware-vCloud-5-1-networking-for-Dummies-part-3/

I hope that's what you're looking for.

Gabrié

Tags: VMware

Similar Questions

My camera iPhone 5s is accessed remotely? Whenever I use my phone torch ends up taking videos. Is it possible for a person to access my camera through the torch. We share the same Apple ID

My camera iPhone 5s is accessed remotely? Whenever I use my phone torch ends up taking videos. Is it possible for a person to access my camera through the torch. We share the same Apple ID

N °

but maybe you tap the camera icon (bottom-right) when you press the icon of the torch (with the other hand maybe?)

Help access remote in a 5505

Hi all. Need help with a remote in a 5505. I can vpn in fine, I can't pass any traffic. When I do a ' sho cryp ipsec her ", I see the traffic that is decrypted, but I see not all traffic is encrypted to me. I have attached to my config, I could get help from you guys to see where I have gone wrong? I appreciate as always.

Why it happens is because the ASA also has a L2L tunnel and you use same NAT 0 access-list to L2L tunnel as Crypto ACL also.

NAT (inside) 0-list of access tocw

card crypto outside_map 10 correspondence address tocw

If the traffic that you send from vpn client is actually back to L2L tunnel.

Follow these steps:

Create access list separate for tunnel L2L specifying only specific L2L tunnel traffic.

you need to check the remote side, but I think your crypto ACLs for l2l tunnel

Access extensive list ip 192.168.201.0 VPNACL allow 255.255.255.0 192.168.73.0 255.255.255.0

No crypto outside_map 10 correspondence card for tocw

outside_map card crypto 10 corresponds to the address VPNACL

Your L2L tunnel will descend when you make changes then make necessary arrangements.

Verify and validate results

HTH

Sangaré

Pls rate helpful messages

Split tunneling cannot access remote host

Hi guys,.

Having this problem by which I am able to connect the Anyconnect client but unable to ping / access of remote servers. See below for the config of the SAA;

Any ideas would be a great help, thank you!

ASA Version 9.1 (1)

!

ASA host name

enable the encrypted password xxxxxxx

xxxxxxxxxxxxx encrypted passwd

names of

mask of local pool AnyPool 10.0.0.1 - 10.0.0.10 IP 255.255.255.0

!

interface GigabitEthernet0/0

nameif outside

security-level 0

IP address 203.106.x.x 255.255.255.224

!

interface GigabitEthernet0/1

nameif inside

security-level 99

IP 172.19.88.254 255.255.255.0

!

interface Management0/0

management only

nameif management

security-level 100

IP 192.168.1.1 255.255.255.0

!

passive FTP mode

clock timezone 8 MYT

the SVR object network

Home 172.19.88.11

e-mail server in description

network of the NETWORK_OBJ_172.19.88.0_24 object

172.19.88.0 subnet 255.255.255.0

network of the VPN-POOL object

10.0.0.0 subnet 255.255.255.0

object-group Protocol TCPUDP

object-protocol udp

object-tcp protocol

object-group service DM_INLINE_SERVICE_0

ICMP service object

area of service-purpose tcp - udp destination eq

the destination hostname eq tcp service object

the purpose of the tcp destination eq https service

the purpose of the tcp destination eq imap4 service

the purpose of the tcp destination eq nntp service

the purpose of the tcp destination eq pop3 service

the purpose of the tcp destination eq smtp service

the purpose of the tcp destination eq telnet service

Outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_0 any object SVR

Outside_access_in list extended access allow TCPUDP of object-group a

Outside_access_in access-list extended ip any any idle state to allow

Internal_access_in list extended access allow TCPUDP of object-group a

Internal_access_in access-list extended ip any any idle state to allow

SPLIT_TUNNEL list standard access allowed 10.0.0.0 255.255.255.0

pager lines 24

Enable logging

timestamp of the record

exploitation forest-size of the buffer 16384

buffered logging critical

asdm of logging of information

Debugging trace record

exploitation forest flash-bufferwrap

record level of the rate-limit 1000 1 2

management of MTU 1500

MTU 1500 internal

Outside 1500 MTU

no failover

ICMP unreachable rate-limit 1 burst-size 1

ASDM image disk0: / asdm - 711.bin

don't allow no asdm history

ARP timeout 14400

no permit-nonconnected arp

!

the SVR object network

203.106.x.x static NAT (indoor, outdoor)

!

source of auto after the cessation of NAT (inside, outside) dynamic interface

Internal_access_in in interface internal access-group

Access-group Outside_access_in in interface outside

Route outside 0.0.0.0 0.0.0.0 203.106.23.97 1

Timeout xlate 03:00

Pat-xlate timeout 0:00:30

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

Floating conn timeout 0:00:00

dynamic-access-policy-registration DfltAccessPolicy

identity of the user by default-domain LOCAL

the ssh LOCAL console AAA authentication

LOCAL AAA authorization command

Enable http server

http 192.168.1.0 255.255.255.0 management

http authentication certificate management

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

No vpn sysopt connection permit

Crypto ipsec ikev2 ipsec-proposal OF

encryption protocol esp

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 proposal ipsec 3DES

Esp 3des encryption protocol

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 ipsec-proposal AES

Esp aes encryption protocol

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 ipsec-proposal AES192

Protocol esp encryption aes-192

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 AES256 ipsec-proposal

Protocol esp encryption aes-256

Esp integrity sha - 1, md5 Protocol

Crypto ipsec pmtu aging infinite - the security association

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF

card crypto Outside_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

Outside_map interface card crypto outside

Crypto ca trustpoint ASDM_TrustPoint0

Terminal registration

name of the object CN = ASA

Configure CRL

Crypto ca trustpoint Anyconnect_TrustPoint

registration auto

name of the object CN = ASA

anyconnect_rsa key pair

Configure CRL

Crypto ca trustpoint _SmartCallHome_ServerCA

Configure CRL

trustpool crypto ca policy

string encryption ca Anyconnect_TrustPoint certificates

IKEv2 crypto policy 1

aes-256 encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 10

aes-192 encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 20

aes encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 30

3des encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 40

the Encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

Crypto ikev2 activate out of service the customer port 443

Crypto ikev2 access remote trustpoint Anyconnect_TrustPoint

Telnet timeout 3

SSH 172.19.88.0 255.255.255.0 internal

SSH 0.0.0.0 0.0.0.0 outdoors

SSH timeout 15

Console timeout 0

management of 192.168.1.100 - 192.168.1.200 addresses dhcpd

enable dhcpd management

!

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

NTP server 119.110.97.148 prefer external source

SSL-trust outside Anyconnect_TrustPoint point

WebVPN

allow outside

AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

AnyConnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2

AnyConnect image disk0:/anyconnect-linux-2.5.2014-k9.pkg 3

AnyConnect profiles AnyConnect_client_profile disk0: / AnyConnect_client_profile.xml

AnyConnect enable

attributes of Group Policy DfltGrpPolicy

VPN-tunnel-Protocol ikev1, ikev2 ssl clientless ssl ipsec l2tp client

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list SPLIT_TUNNEL

Group Policy 'GroupPolicy AnyConnect' internal

Group Policy attributes "GroupPolicy AnyConnect"

value of server WINS 172.19.88.11

value of server DNS 172.19.88.11

SSL VPN-tunnel-Protocol ikev2 client ssl clientless

WebVPN

AnyConnect value AnyConnect_client_profile type user profiles

attributes global-tunnel-group DefaultWEBVPNGroup

address pool AnyPool

tunnel-group "AnyConnect" type remote access

attributes global-tunnel-group "AnyConnect".

address pool AnyPool

strategy-group-by default "GroupPolicy AnyConnect"

tunnel-group "AnyConnect" webvpn-attributes

Group-alias "AnyConnect" activate

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

Review the ip options

Hi Max,.

Please send me the output of 'see the anyconnect vpn-sessiondb' once connected with VPN.

And try to add the following configuration and see if that helps:

NAT (inside, outside) 1 static source NETWORK_OBJ_172.19.88.0_24 NETWORK_OBJ_172.19.88.0_24 static destination VPN-VPN-POOL no-proxy-arp-route search

And one more qusetion do you use split tunnel? If yes then you must make the following changes, because your split tunnel is incorrect, in the split tunnel, you have configured the address pool of vpn. Please make the following change:

no access list SPLIT_TUNNEL standards not allowed 10.0.0.0 255.255.255.0

Standard access list SPLIT_TUNNEL allow 172.19.88.0 255.255.255.0

Group Policy attributes "GroupPolicy AnyConnect"

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list SPLIT_TUNNEL

Let me know if this can help, or if you have any questions, more about it.

Thank you

Jeet Kumar

Cannot access remote network by VPN Site to Site ASA

Hello everyone

First of all I must say that I have configured the VPN site-to site a million times before. Stuck with it. First of all I can't ping outside the interface of my ASA remote. Secondly, VPN is in place, but no connectivity between local networks

ASA local:
hostname gyd - asa
domain bct.az
activate the encrypted password of XeY1QWHKPK75Y48j
XeY1QWHKPK75Y48j encrypted passwd
names of
DNS-guard
!
interface GigabitEthernet0/0
Shutdown
nameif vpnswc
security-level 0
IP 10.254.17.41 255.255.255.248
!
interface GigabitEthernet0/1
Vpn-turan-Baku description
nameif outside Baku
security-level 0
IP 10.254.17.9 255.255.255.248
!
interface GigabitEthernet0/2
Vpn-ganja description
nameif outside-Ganja
security-level 0
IP 10.254.17.17 255.255.255.248
!
interface GigabitEthernet0/2.30
Description remote access
VLAN 30
nameif remote access
security-level 0
IP 85.*. *. * 255.255.255.0
!
interface GigabitEthernet0/3
Description BCT_Inside
nameif inside-Bct
security-level 100
IP 10.40.50.65 255.255.255.252
!
interface Management0/0
nameif management
security-level 100
IP 192.168.251.1 255.255.255.0
management only
!
boot system Disk0: / asa823 - k8.bin
passive FTP mode
DNS server-group DefaultDNS
name-server 192.168.1.3
domain bct.az
permit same-security-traffic intra-interface
object-group network obj - 192.168.121.0
object-group network obj - 10.40.60.0
object-group network obj - 10.40.50.0
object-group network obj - 192.168.0.0
object-group network obj - 172.26.0.0
object-group network obj - 10.254.17.0
object-group network obj - 192.168.122.0
object-group service obj-tcp-eq-22
object-group network obj - 10.254.17.18
object-group network obj - 10.254.17.10
object-group network obj - 10.254.17.26
access-list 110 scope ip allow a whole
NAT list extended access permit tcp any host 10.254.17.10 eq ssh
NAT list extended access permit tcp any host 10.254.17.26 eq ssh
access-list extended ip allowed any one sheep
icmp_inside list extended access permit icmp any one
icmp_inside of access allowed any ip an extended list
access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh
RDP list extended access permit tcp any host 192.168.45.3 eq 3389
rdp extended permitted any one ip access list
sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0
NAT-vpn-internet access-list extended ip 192.168.121.0 allow 255.255.255.0 any
NAT-vpn-internet access-list extended ip 172.26.0.0 allow 255.255.255.0 any
NAT-vpn-internet access-list extended ip 192.168.122.0 allow 255.255.255.0 any
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.60.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.50.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 192.168.0.0 255.255.0.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 172.26.0.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.254.17.0 255.255.255.0
GHC-ganja-internet access-list extended ip 192.168.45.0 allow 255.255.255.0 any
Standard access list Split_Tunnel_List allow 192.168.16.0 255.255.255.0
azans 192.168.69.0 ip extended access-list allow 255.255.255.0 any
permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.121.0 255.255.255.0
permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.80.0 255.255.255.0
pager lines 24
Enable logging
emblem of logging
recording of debug console
recording of debug trap
asdm of logging of information
Interior-Bct 192.168.1.27 host connection
flow-export destination inside-Bct 192.168.1.27 9996
vpnswc MTU 1500
outside Baku MTU 1500
outside-Ganja MTU 1500
MTU 1500 remote access
Interior-Bct MTU 1500
management of MTU 1500
IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0
IP local pool ssl 192.168.121.130 - 192.168.121.200 mask 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any outside Baku
ICMP allow access remotely
ICMP allow any interior-Bct
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
global (outside-Baku) 1 interface
global (outside-Ganja) interface 2
3 overall (RAS) interface
azans access-list NAT 3 (outside-Ganja)
NAT (remote access) 0 access-list sheep-vpn-city
NAT 3 list nat-vpn-internet access (remote access)
NAT (inside-Bct) 0-list of access inside_nat0_outbound
NAT (inside-Bct) 2-nat-ganja access list
NAT (inside-Bct) 1 access list nat
Access-group rdp on interface outside-Ganja
!
Router eigrp 2008
No Auto-resume
neighbor 10.254.17.10 interface outside Baku
neighbor 10.40.50.66 Interior-Bct interface
Network 10.40.50.64 255.255.255.252
Network 10.250.25.0 255.255.255.0
Network 10.254.17.8 255.255.255.248
Network 10.254.17.16 255.255.255.248
redistribute static
!
Access remote 0.0.0.0 0.0.0.0 85.*. *. * 1
Outside-Baku route 10.0.11.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.33.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.150.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.170.0 255.255.255.0 10.254.17.10 1
Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1
Route outside Baku 10.254.17.32 255.255.255.248 10.254.17.10 1
Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 192.168.27.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1
Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.66.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1
Outside-Baku route 192.168.80.0 255.255.255.0 10.254.17.11 1
Access remote 192.168.121.0 255.255.255.0 85.132.43.1 1
Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1
Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1
Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1
Route inside-Bct 192.168.254.0 255.255.255.0 10.40.50.66 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol Ganymede GANYMEDE +.
AAA-server GANYMEDE (Interior-Bct) 192.168.1.8
key *.
AAA-server GANYMEDE (Interior-Bct) 192.168.22.46
key *.
RADIUS protocol AAA-server TACACS1
AAA-server TACACS1 (Interior-Bct) host 192.168.1.8
key *.
AAA-server TACACS1 (Interior-Bct) host 192.168.22.46
key *.
authentication AAA ssh console LOCAL GANYMEDE
Console to enable AAA authentication RADIUS LOCAL
Console Telnet AAA authentication RADIUS LOCAL
AAA accounting ssh console GANYMEDE
Console Telnet accounting AAA GANYMEDE
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.1.0 255.255.255.0 Interior-Bct
http 192.168.139.0 255.255.255.0 Interior-Bct
http 192.168.0.0 255.255.255.0 Interior-Bct
Survey community SNMP-server host inside-Bct 192.168.1.27
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto ipsec transform-set newset aes - esp esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac myset2
Crypto ipsec transform-set esp-3des esp-md5-hmac raccess
Crypto ipsec transform-set esp-3des esp-sha-hmac vpnclienttrans
Crypto ipsec transform-set vpnclienttrans transport mode
life crypto ipsec security association seconds 2147483646
Crypto ipsec kilobytes of life security-association 2147483646
raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map
correspondence address card crypto mymap 10 110
card crypto mymap 10 peers set 10.254.17.10
card crypto mymap 10 transform-set RIGHT
correspondence address card crypto mymap 20 110
card crypto mymap 20 peers set 10.254.17.11
mymap 20 transform-set myset2 crypto card
card crypto mymap interface outside Baku
correspondence address card crypto ganja 10 110
10 ganja crypto map peer set 10.254.17.18
card crypto ganja 10 transform-set RIGHT
card crypto interface outside-Ganja ganja
correspondence address card crypto vpntest 20 110
peer set card crypto vpntest 20 10.250.25.1
newset vpntest 20 transform-set card crypto
card crypto vpntest interface vpnswc
vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1
card crypto interface for remote access vpnclientmap
Crypto ca trustpoint ASDM_TrustPoint0
registration auto
name of the object CN = gyd - asa .az .bct
sslvpnkeypair key pair
Configure CRL
map of crypto DefaultCertificateMap 10 ca certificate

crypto isakmp identity address
ISAKMP crypto enable vpnswc
ISAKMP crypto enable outside-Baku
ISAKMP crypto enable outside-Ganja
crypto ISAKMP enable remote access
ISAKMP crypto enable Interior-Bct
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 20
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 40
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Crypto isakmp nat-traversal 30
No vpn-addr-assign aaa
Telnet timeout 5
SSH 192.168.0.0 255.255.255.0 Interior-Bct
SSH timeout 35
Console timeout 0
priority queue outside Baku
queue-limit 2046
TX-ring-limit 254
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Server NTP 192.168.1.3
SSL encryption, 3des-sha1 rc4 - md5 aes128-sha1 sha1-aes256
SSL-trust point ASDM_TrustPoint0 to vpnlb-ip remote access
SSL-trust ASDM_TrustPoint0 remote access point
WebVPN
turn on remote access
SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image
enable SVC
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
internal group ssl policy
attributes of group ssl policy
banner welcome to SW value
value of DNS-server 192.168.1.3
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
group-lock value SSL
WebVPN
value of the SPS URL-list
internal vpn group policy
attributes of vpn group policy
value of DNS-server 192.168.1.3
Protocol-tunnel-VPN IPSec l2tp ipsec
disable the PFS
BCT.AZ value by default-field
ssl VPN-group-strategy
WebVPN
value of the SPS URL-list
IPSec-attributes tunnel-group DefaultL2LGroup
ISAKMP retry threshold 20 keepalive 5
attributes global-tunnel-group DefaultRAGroup
raccess address pool
Group-RADIUS authentication server
Group Policy - by default-vpn
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
IPSec-attributes tunnel-group DefaultWEBVPNGroup
ISAKMP retry threshold 20 keepalive 5
tunnel-group 10.254.17.10 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.10
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
type SSL tunnel-group remote access
attributes global-group-tunnel SSL
ssl address pool
Authentication (remote access) LOCAL servers group
Group Policy - by default-ssl
certificate-use-set-name username
Group-tunnel SSL webvpn-attributes
enable SSL group-alias
Group-url https://85. *. *. * / activate
tunnel-group 10.254.17.18 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.18
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
tunnel-group 10.254.17.11 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.11
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
type tunnel-group DefaultSWITGroup remote access
attributes global-tunnel-group DefaultSWITGroup
raccess address pool
Group-RADIUS authentication server
Group Policy - by default-vpn
IPSec-attributes tunnel-group DefaultSWITGroup
pre-shared key *.
!
type of policy-card inspect dns migrated_dns_map_1
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect sunrpc
inspect xdmcp
inspect the netbios
Review the ip options
class flow_export_cl
flow-export-type of event all the destination 192.168.1.27
class class by default
flow-export-type of event all the destination 192.168.1.27
Policy-map Voicepolicy
class voice
priority
The class data
police release 80000000
!
global service-policy global_policy
service-policy interface outside Baku Voicepolicy
context of prompt hostname

Cryptochecksum:4f35f975ba7a0c11f7f46dfd541d266f
: end
GYD - asa #.

ASA remote:
ASA Version 8.2 (3)
!
ciscoasa hostname
activate the encrypted password of XeY1QWHKPK75Y48j
2KFQnbNIdI.2KYOU encrypted passwd
names of
DNS-guard
!
interface Ethernet0/0
nameif inside
security-level 100
IP 192.168.80.14 255.255.255.0
!
interface Ethernet0/1
nameif outside
security-level 0
IP 10.254.17.11 255.255.255.248
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
nameif management
security-level 100
no ip address
management only
!
boot system Disk0: / asa823 - k8.bin
passive FTP mode
access-list 110 scope ip allow a whole
192.168.80.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.0.0 255.255.0.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
management of MTU 1500
Within 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow all outside
ICMP allow any inside
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside) 0 access-list sheep
Route outside 0.0.0.0 0.0.0.0 10.254.17.9 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.80.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto ipsec transform-set newset aes - esp esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac myset2
life crypto ipsec security association seconds 2147483646
Crypto ipsec kilobytes of life security-association 2147483646
correspondence address card crypto mymap 10 110
card crypto mymap 10 peers set 10.254.17.9
mymap 10 transform-set myset2 crypto card
mymap outside crypto map interface
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 20
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 40
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN

tunnel-group 10.254.17.9 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.9
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns migrated_dns_map_1
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname

Cryptochecksum:1c1ac60e2fb84f65269d15d53f27c21b
: end
ciscoasa # $

Still, I can't ping ASA remote outside from outside of the Local interface. And there is no connectivity between the 192.168.80.0 distance and local don't say 192.168.1.0. I have run out of ideas

Would appreciate any help. Thank you in advance...

If the tunnel is up (phase 1), but no traffic passing the best test is the following:

Add order management-access to the Interior , and then try to PING the intellectual property inside ASA counterpart.

inside x.x.x.x ping --> x.x.x.x is the IP of the ASA peer inside

The test above shows if the traffic passes through the tunnel (check encrypted/decrypted packets of sh cry ips its).

Test on both directions.

Please post the results.

Federico.

Our computer was accessed remotely this afternoon, how can we prevent this?

We have a Mac Mini, with OS X 10.6.8 using NetZero DSL as our internet provider and Firefox as your browser. Our computer was accessed remotely through LogMeIn (rescue), but it seems that the person or the group failed to hack into our computer. Are there settings in Firefox that could prevent this from happening in the future? Thank you...

Firefox is a web browser not a firewall.

I agree that it's more to do with your operating system and the LogMeIn software on ensuring that only you have access when you need to.

I need 32-bit to run access remotely for the work but have Windows 7 (64)

I have a new Dell with Windows 7 laptop. To work from home, I use a program of remote access that will not work with 64 bit but needs 32. I have been informed that I need to buy Windows Vista. Is this really necessary?

Thank you.

Hello Lyndaware,

Thank you for your message. 64-bit operating systems will be run 32-bit applications, however, you might have been told that your application is compatible with Windows 7. I would advise that you check with your IT support to get better clarification of why you need Windows Vista. For now, Microsoft sold more Vista, but you may be able to find a copy online or through your local dealer.

See you soon

Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

How can I use VPN to access my work files?

Original title: VPN connection... then what?

Our IT consultant gave me a procedure to set up a VPN between home and work. I can establish a VPN connection now. I can see the handshake of communication by the illustration. All this is well and good, but how use VPN to access my work files? In Logmein, I get a screen that remotes me to my work PC. With VPN I get nothing.

Hello

Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Technet Forum.

http://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itprogeneral

I hope this helps.

1920 router access remote vpn LDAP living

Hello

What is required for a router in 1920 use AnyConnect and/or also integrate with AD LDAP?

Currently, this router supports legacy clients and has these licenses:

Technology for the Module package license information: "c1900".

-----------------------------------------------------------------
Technology-technology-package technology
Course Type next reboot
------------------------------------------------------------------
IPBase ipbasek9 ipbasek9 Permanent
Security securityk9 Permanent securityk9
given none none none

The vpn to access remote client inherited integrate with AD LDAP?

Thank you.

As long as you are on IOS 15.3.3M3 or better, you have all the licenses you need for 3.1 AnyConnect run on your 1921.

The guide to directly connect your router to LDAP can be found here:

http://www.Cisco.com/c/en/us/TD/docs/iOS-XML/iOS/sec_usr_ldap/configuration/15-Mt/sec-usr-LDAP-15-Mt-book/sec_conf_ldap.html

Personally, I would avoid directly interfacing with LDAP, because it can be a complex arrangement. While it can be done, it's easier to have your router to connect to the NPS Microsoft via RADIUS server for your authentication.

Should I static if I'm not using nat on pix 6.2?

I have pix 6.2 and not nat address translation, I use everything I have nat from the East:

NAT (inside) - 0 200 access list

NAT (inside) 0 0.0.0.0 0.0.0.0 0 0

NAT (dmz:2) 0 0.0.0.0 0.0.0.0 0 0

and then I have the configured static next:

static (inside, outside) LotusSrv LotusSrv netmask 255.255.255.255 0 0

static (inside, outside) 81-mail mail-81 netmask 255.255.255.255 0 0

static (inside, outside) Bookstore Bookstore netmask 255.255.255.255 0 0

static (inside, dmz:2) 204.142.81.0 204.142.81.0 netmask 255.255.255.0 0 0

static (dmz:2, outside) Venus Venus netmask 255.255.255.255 0 0

and much more... but not for guests...

Lie, I have no overall control.

I just want to know what are these static commands, I can delete them and how to decide who hosts that I have to configure static?

Statix expose ip addresses of interfaces of high security to low security ints. Once created, you can then use pipes or access lists to allow access of ints low to high s ints. Then Yes, you need to keep all those who, if they provide services to the outside world.

Matt

2 VPN SITE to SITE with ACCESS REMOTE VPN

Hello

I have a 870 router c and I would like to put 2 different VPN SITE to SITE and access remote VPN (VPN CLIENTS) so is it possible to put 3 VPN in the router even if yes can u give me the steps or the sample configuration

Concerning

Thus, on the routers will be:

Cisco 2611:

LAN: 10.10.10.0/24

access-list 100 permit ip 10.10.10.0 0.0.0.255 10.10.20.0 0.0.0.255

access-list 100 permit ip 14.1.1.0 0.0.0.255 10.10.20.0 0.0.0.255--> VPNPOOL

!

10 ipsec-isakmp crypto map clientmap

defined by peer 172.18.124.199

match address 100

!

IP local pool ippool 14.1.1.1 14.1.1.254

!

access-list 120 allow ip 10.10.10.0 0.0.0.255 14.1.1.0 0.0.0.255

access-list 120 allow ip 10.10.20.0 0.0.0.255 14.1.1.0 0.0.0.255 --> NETWORK REMOTE

!

crypto ISAKMP client configuration group ra-customer

pool ippool

ACL 120

!

Please note that the configuration is incomplete, I added that relevant changes, you should bring to the allow clients of RA through the LAN-to-LAN tunnel, of course, the LAN-to-LAN settings should match to the other side of the tunnel that is mirror of ACL, NAT and so on.

HTH,

Portu.

Please help: NAT (inside) 0 0 0 and NAT (inside) - access list 0

I have a problem with my PIX firewall.

I don't want any NAT to the origin of traffic inside the interface.

When I give

NAT (inside) - 0 80 access list

access ip-list 80 allow a whole

It works very well

But when I tried

NAT (inside) 0 0 0

ITZ not working is not for my IPsec clients

According to my knowledge PIX requires input NAT to allow traffic from security interface higher to lower security interface. Can I use NAT 0 by which I can get around the NAT.

Help, please?

Hello

identity nat works with access-list... IE nat 0 statement with an ACL... or you can specify the network... don't know if you can put 0 0... I have not seen that someone put this...

refer to the documentation of nat for this command:

http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_sw/v_63/cmdref/Mr.htm#wp1161298

to the first config... That's right... who has a list of acess 80!

REDA

Newbie question: in what configuration file < flex: access remote destination > tags go?

I seem to have read the document integration spring/Blaze about 10 times, but I don't know where to put all my < flex: access remote-Ref destination = "yaddayaddaService" / > tags. I don't want annotation allows you to set these remote destinations.
Should it go in the spring configuration file that I use for the servlet of AMF endpoint (as specified by the contextConfigLocation parameter). Or they go to a high-level cross-servlet configuration file?
What is the usual way to deal with these?

Hello

The convention is to declare:

1 declare the Spring beans (for example yaddayaddaService) in the files specified by the parameter contextConfigLocation.

2. Add the Spring - Flex specific configuration (configure message agent, declare destinations) in WEB-INF\flex- servlet.xml, assuming that you have configured the model of Message Broker URL as follows in the web.xml file:


        Flex
        org.springframework.web.servlet.DispatcherServlet
        1



        Flex
        messagebroker / *.


The repository SVN BlazeDS/distribution contains the spring sample webapp (spring - samples.war) that you can watch as well.

Hope that helps.

Rohit

Can I use Siri new Apple remote with my Apple TV 3rd generation?

Can I use Siri new Apple remote with my Apple TV 3rd generation?

No. not compatible.

I want to use Outlook Web Access for Mac, I don't want to use the light version, I want the full version, but you can't push off the mark. I have firefox 3.6.10

I want to use Outlook Web Access for Mac (snow leopard 10.6.8), I don't want to use the light version, I want the full version but I can't push off the mark on the light version. I have firefox 3.6.10

(1) you must update at least Firefox 3.6.24 because there are questions of SECURITY of KNOWN MANY with the version you are using.

(2) the light version is required on non - IE browsers, except if you are running Exchange Server 2010. With Exchange 2010 they added support for multiple browsers run in the version "no light".

Using NAT to access remote vCD 5.1

Similar Questions

Maybe you are looking for