Using the Codec C90 Tandberg T1 with CUCM

Similar Questions

• Daisy chaining for 2 PrecisionHDMC 720 p cammera with 1 PrecisionHDMC 1080 p, with the codec C90

  Hello

  Is it possible to daisy chaining for 3 cammeras having different resolutions, with the codec C90?

  2 PrecisionHDMC 720 p cammera with 1 PrecisionHDMC 1080 p, with the codec C90

  Thank you very much!!

  Hi Moreno,

  Control of the camera uses the visca Protocol, it is same in both cameras.

  I tested previously and she works in the laboratory.

  Kind regards

  Dharmmesh

• I have a psc 1350 HP which cannot me use the scanner, due to incompatibility with Internet Explorer 8.

  I have a psc 1350 HP which cannot me use the scanner, due to incompatibility with Internet Explorer 8.  When I use their "fix", it turns out that my screen blue and green. Aid others?

  Your support for the product is unfortunately - the manufacturer of the product.

  Suppose you tried everything here:
  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?lang=en&cc=us&TaskID=110&prodSeriesId=306884&prodTypeId=18972&ObjectID=c00802504

• I installed Vista in a Virtualbox VM and the product key does not work, how to fix this? I use the same product key supplied with the computer originally.

  I bought a Dell Precision T3400 of Dell Financial Services and it came with Vista Business installed.  I installed a new hard drive and installed Vista in a Virtualbox VM by using the recovery disk that came with the computer, and the product key does not work for activation.  I get a message that says I need to activate Windows, but he says that the product key is not valid.  How can I fix it?

  Thank you

  If you have reinstalled the OEM of Vista Business copy on the new hard drive, as Bill says you can't also use it in a virtual machine.

  You can only reuse your OEM of Vista professional copy if it is no longer used on the computer. Do you have what operating system installed on the new hard drive? It was an upgrade copy or complete the license?

  If you used a license to upgrade to another edition of Windows to replace your copy of company then Vista Business license is still in use (for upgrade) and you cannot reuse it in your virtual machine.

  However if you replaced Vista business with a copy of the full license of another edition then you are able to use the OEM copy in a virtual machine, but only on the same computer. You must use the product key from COA to the label on the computer. The product key is put in the copy OEM cannot find the SLIC table on the host motherboard. You must use the phone activation from within the virtual machine. Click on start in Vista Business and typing "slui 4. Do not meet the audio guests until it asks you if you want to speak to an agent. Explain that you have completely replaced the OEM copy with a copy of the full license of the new windows and now want to use the OEM copy in a virtual machine on the same computer. Agent will then give you the activation string. Remember that the virtual machine is not transferable to any other computer.

  This information is offered by Darin Smith (MSFT) and the team of Windows licenses, November 18, 2011.

• Can I use the library of creative cloud with Illustrator CS5

  Can I use the library of creative cloud with Illustrator CS5

  Hi Ilys Ravel,

  No, CC libraries function is available in version CC 20141 sur-quartiers.

  Sanjay...

• Can I use the Windows Vista I had with my Toshiba laptop on virtual machine?

  Hey all

  I have changed Microsoft for Macintosh, but installed on a virtual machine (oracle vm virtual machine) my Windows Vista I got with my Toshiba Satellite A350D Notebook previous. I installed Vista with the recovery disk. Now he asks me the Windows Vista product key. The sticker on the back of my laptop is more readable. I run the Belarc Advisor to get the product key in this way. But right now, he said: "it's the product key installed at the factory by the manufacturer rather than yours. You can change this to your product key here for Windows http://go.microsoft.com/fwlink/?LinkId=45668"

  My question: am I not allowed to use windows vista legally, I had with my computer toshiba laptop on other devices? I won't use the Thoshiba laptop. Do I have to delete the record from the Thoshiba laptop? Where can I get a new product key?

  Maybe someone can help me here. Thank you in advance for taking your time to read this.

  Betty

  Recovery disk or recovery image is designed for some cell phone only and is not a kind of universal image that can be used on other devices. It comes with the laptop.

  You can use the Microsoft Windows disk with valid license on each device. Recovery image is not only BONES. This is the package that contains the drivers and tools specific to Toshiba and utilities.
  As you also know recovery image when you install it on your laptop must be turned on not so the license code downstairs just proves you have purchased a valid license with your laptop.
  > Should I remove the record of the Toshiba laptop?
  Not why do this?
  > Where can I get a new product key?
  You cannot get it because you need when you use the recovery image on your Satellite A300D. I think even you will hear of Toshiba.

• Tecra M5: How to use the FN + F2 fast locking with external keyboard keys?

  When to use a docking station and the keyboard of the UBS, the function key ("Fn + F2") on my tecra M5 as will not work. The USB keyboard has a Fn key, but when you press on with F2 nothing happens. Can I lock the screen another way?

  Usually, by default the FN keys work only on the internal keyboard.
  If you want to use the function key FN keyboard USB external, you must first activate this function FN.
  This function, you can enable in the Toshiba HWSetup located under the control panel.
  Here, you will need to select the keyboard tab and assign a function to the FN key on the external keyboard Fn key window.

  Hope this works

• Could someone use the iMac as a monitor with a new MacBook Pro?

  We bought a new 13 "MacBook Pro and still have our old iMac monitor. It would be great to use the large size of the old, almost dead iMac screen. Does anyone have this done successfully?

  Thank you!

  Only some models of iMac (latest) have the ability to be used as a screen for another Mac.  This function is called target Display Mode.  This document contains more information, including the models of iMac with the ability to target Display Mode.

  Use your iMac as a display with the target - Apple Support Display Mode

• Is it possible to use the software version of pages with the online version?

  I know that google docs has a feature where all those who have access to a document can edit it at the same time and everyone can see the changes as they are made. To me, it looks like the iCloud.com pages is the same too. I was wondering if a user of Microsoft could go online with his apple ID, login to iCloud.com, open a pages document that I shared with him with iCloud pages and work together with me, that has the version of the pages on my mac software. I want to be able to see the changes he makes on the request pages. If this is not possible, I have to go to iCloud.com as well?

  Thanks in advance!

  Hi TheExpolsiveCow,

  Welcome to the communities of Apple Support! If you use Pages for Mac, you should be able to share your document via iCloud to other users for collaboration or editing, even if they do not have an account iCloud.com. There is also an option for free iCloud only accounts on the Web for non-Apple users. For more information about these options and the sharing features you may find useful the following items:

  Use iWork with iCloud drive - Apple Support

  Pages for Mac 5.0: share a document on iCloud

  Only Web access to iCloud - Apple Support

  See you soon

• When should I use the IRIS PRO that came with my 8600 instead of the built-in OCR scan-to-text?

  I just bought the Premium Pro 8600.  I installed the HP software, that gives me an OCR option for scanning.  I also installed the second disc, IRIS PRO, which is OCR, too.  When should I use each?

  I would use the software OCR supplied with the printer during the formatting of the document to be scanned is simple and use the IRIS PRO when the formatting is more complex.  You should expect some distortion of the two programs well formatted.  Hope that helps.

• How to use the kit sensor Bioinstrumentation Vernier with NI ELVIS II and LABview on a CPU?

  So I have the NI ELVIS II + and a box full of Bioinstrumentation sensor, including Kit sensors: Analog Proto board connector (s), pressure sensor, hand dynamometer, hand grip monitor heart rate, EKG sensors, Surface temperature probe, among others.

  I can't seem to get all the sensor data to my PC that I use, I'm not too familiar with electrical circuits but I followed the manual directions for the specific sensor but it seems as if it doesn't have a difference. I'm with copper son crochet and so that they know the places appropriate (according to the manual) but nothing.

  Am I missing something? I have also the is open regardless of the specific LABview laboratory (Surface Temp lab for example), but when I press run it is as the sensors are not recognized or even be recognized. The sensors are plugged into the connectors on the analog Proto Board also. What I am doing wrong, and how can I get these sensors to work?

  Any help will be greatly appreciated.

  From what I see, it looks like a typing mistake in the manual.

  Try to connect GND AI0 - and NOT ALWAYS.

  It should look like this.

  Connect the following pins for wire connector:

  1. AI0 + SIG1 analog connector Proto Board

  2. + 5V power supply DC to 5V analog Proto card connector

  3. Power supply to the GROUND to GND of the analog Proto board connector

  4. AI0 - GND of the analog connector Proto Board

• How to use the sim card that comes with my thinkpad tablet 3G version?

  I got my tablet from newegg and my Tablet comes with a sim card AT & T, how to use this map? I have to go to the AT & T sign a contract and activate store? I'm in the United States
  Thank you!

  At & t will put you on a laptop data plan which is more expensive than a plan of "ipad." If you can, find an IMEI of an Ipad and use the sim card number and the IMEI number of the Ipad for you sign up for a plan of cost reduction. Call them to implement. Using an online form or walk into a store At & t will be very frustrating.

  PS: it is there no contract that your device is not supported by anyone - you own. It will be a month of service. If you don't sign up, free of charge.

  What, the bonus is a kick butt gps integrated 3G wwan card. Enjoy!

• upggrading a windows xp pro service pack 3 with the new card mother and pure install using the original disk of xp with service pack 2

  I have an auto build Windows XP pro with service pack 3 that is upwards and I feel the need to upgrade to a new motherboard and processor causes memory and I know that when I do a clean install with my original disk, I lose service pack 3 that will then lose me the Microsoft support is anyway that I can backup service pack 3 for use with what will be considered a brand new computer

  See you soon

  The site is authentic.  You have two options when you do your relocation:

  Method 1

  1. Download SP3 form the Microsoft site and burn it to a cd or copy it to a flash drive.
  2. Reinstall Windows with your original Windows XP CD.
  3. Use the copy of SP3 that you burned on the CD or copied to the flash drive and update the machine to SP3.  Note that if you have an original CD of 'gold' of Windows XP without service pack that you install SP1a or SP2 before you install SP3, SP2 is available here , download and save it with SP3 before making your relocation.

  Method 2

  1. Download SP3 from the Microsoft site and it wake to your Windows XP CD.
  2. Install Windows XP with your slipstreamed CD and your installation will be in SP3, when installation is complete you will not need to install service packs, you'll just have to do some other updates that have been released after SP3.

  The http://lifehacker.com/386526/slipstream-service-pack-3-into-your-windows-xp-installation-cd is legitimate, it only gives you instructions on how to create and burn a CD of SP3 slipstreamed Windows XP.  If this seems too daunting then use method 1 to install Windows.

  Both methods are very good but method 2 allows a nicer cleaner installation, everything is installed to SP3 level and there are no remnants of previous service packs.  While creating the slipstreamed CD may appear to be a time consuming task, in the end, it will be a time saver and afterwards if you ever have problems with the installation of Windows you may need this cd SP3 slipstreamed to all repairs on the installation.  You can create the SP3 cd now and do it ready and at hand for future needs.

  John

• Cannot use the numeric keypad codes alt with usb keyboard.

  I just bought a bow of Microsoft keyboard for use with my Vista system. As I am a programmer and the keyboard is missing a number pad (which I use frequently for the entry of characters alt-code), I bought a USB keyboard separated (from Targus - model AKP10CA) mainly to enter alt character codes

  To my dismay, the alt codes don't work! I checked the keycodes that sends the keyboard with a keylogger, and they are the correct numeric keypad keys. So my question is why these don't work with my Microsoft Arc keyboard alt key, and what I can do about it?

  Thank you.

  Well, at least we have excluded the keyboard as the problem - I don't really think it was but it was worth checking out.

  I don't know (I don't use keyboard shortcuts), but have you tried turning on the number lock on your keyboard and using the numbers on the different keys on the keyboard that are used instead of a numeric keypad when you don't have available?  I don't mean the numbers at the top (I know that they do not work) but if you set the keyboard for some keys work as a numeric keypad, and then perhaps shortcuts using these buttons by activating the NunLock will work as expected.  Always turning on one off the NumLock sort of defeats, the goal to make shorter (but it can work entirely from the keyboard that was your question).

  I do not think it is possible to get this work because the keyboard and the numeric keypad USB are separate devices and do not speak to one another - can 'see' what is happening on the other device and there is therefore no way to make them work in oncert.  The system does not recognize that the two entries are supposed to actually a single action and I don't know any way to tell the system how to do if it is possible at all (even with a registry change).  I have no idea where to start comiing even upward with a workaround.  I think you just need to live with the fact that you can not use the devices together to issue commands.  Maybe you can change some of the most frequently used shortcuts involving the keypad for a different shortcut, not requiring that the keyboard - shortcuts can be re-scheduled (and if you can not re - schedule a current shortccut you ccan still create a new shortcut using only the keyboard, which performs the same function).

  I'm sorry, there is no real solution to your problem, but it's the way Vista works and we just have to live with it, the better we can.

  Good luck and best wishes!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• try to use the webcam on my dell with movie maker and I can't. It is built in.

  My laptop has a webcam.  I need to make a video for my HR class.  Movie Maker can't it?  What should I do?

  Hello
   
  Movie maker cannot capture or record a video, it will edit only video. As long as the video is already saved on your computer, you should be able to open or edit with Movie maker.
   
  Windows Movie Maker no longer supports importing video from a webcam or an analog video source such as a VCR. To use video from your web camera, use the software provided with the camera to record the video to your computer, and then import the video file in Windows Movie Maker.
   
  If you encounter problems with importing files into a movie maker, you can consult the following link for more information:
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-importing-files-into-Windows-Movie-Maker
   
  I hope this helps.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.