Using VPN Client coming out behind a PIX

As I understand it, a PIX can operate as a VPN endpoint for IPsec tunnels, or allow IPsec traffic to pass to the other endpoints behind him; My PIX is an end point, but there are a few users who wish to use the VPN Client to connect to outside points beyond the firewall.

Is it possible to configure a PIX to two pass through IPsec traffic AND be an endpoint?

On a related note, two customer software VPN hosts can connect to each other?

Thank you

Marc

My pix company does exactly what you posted, there is lan - lan vpn, and we again establish vpn to other companies via a software vpn client.

concerning the transmission of described video, it should not need additional acl or configuration assuming that there is no acl on the pix. a question must be noticed is that the other end (i.e. the end point of the remote vpn client) needs to nat-traversal since the local pix usually perform nat/pat.

However, the vpn directly between two clients is not feasible as its name suggests (they are the two client).

Tags: Cisco Security

Similar Questions

VPN clients cannot access remote sites - PIX, routing problem?

I have a problem with routing to remote from our company websites when users connect via their VPN client remotely (i.e. for home workers)

Our headquarters contains a PIX 515E firewall. A number of remote sites to connect (via ADSL) to head office using IPSEC tunnels, ending the PIX.

Behind the PIX is a router 7206 with connections to the seat of LANs and connections to a number of ISDN connected remote sites. The default route on 7206 points to the PIX from traffic firewall which sits to ADSL connected remote sites through the PIX. Internal traffic for LAN and ISDN connected sites is done via the 7206.

Very good and works very well.

When a user connects remotely using their VPN client (connection is interrupted on the PIX) so that they get an IP address from the pool configured on the PIX and they can access resources located on local networks to the office with no problems.

However, the problem arises when a remote user wants access to a server located in one of the remote sites ADSL connected - it is impossible to access all these sites.

On the remote site routers, I configured the access lists to allow access from the pool of IP addresses used by the PIX. But it made no difference. I think that the problem may be the routes configured on the PIX itself, but I don't know what is necessary to solve this problem.

Does anyone have suggestions on what needs to be done to allow access to remote sites for users connected remotely via VPN?

(Note: I suggested a workaround, users can use a server on LAN headquarters as a "jump point" to connect to remote servers from there)

with pix v6, no traffic is allowed to redirect to the same interface.

for example, a remote user initiates an rdp session for one of the barns adsl. PIX decrypts the packet coming from the external interface and looks at the destination. because the destination is one of adsl sites, pix will have to return traffic to the external interface. Unfortunately, pix v6.x has a limitation that would force the pix to drop the packet.

with the v7, this restriction has been removed with the "same-security-traffic control intra-interface permits".

http://www.Cisco.com/en/us/partner/products/HW/vpndevc/ps2030/products_configuration_example09186a008046f307.shtml

SonicWALL NSA, using VPN client overall comments to reach network of internal resources

Hello

I have problems performing Global VPN client to work when you connect to our internal network of comments in order to reach our internal LAN Server in order to reach internal resources in a safe manner. I'm not sure what could the settings were necessary in the Sonicwall to achieve?

Our installation is based on the NSA 3600 and I installed a WLAN area in the sonicwall to enable clients to connect to the internet. Traffic in the WLAN area to our internal LAN Server is denied. However, some users would like to be able to use the wireless network in order to achieve internal resources and for that I want to use the Global VPN client. It is even possible to use of an internal network from the point of view Sonicwalls Global VPN client?

The use of the outside Global VPN client works very well

Any help is greatly appreciated and if more detailed configuration information are necessary, I'll happily give you that.

Thank you

Hi Ben,

No I didn't at first, but your answers have would lead me in the right direction, hopefully. I realized that I could create a custom GroupVPN by going to the settings of the interface to the interface that is the war in the Gulf to my wireless network.

return to results

Thank you

Cree

Number of VPN clients behind a PIX 501, restriction?

Is there a restriction in the number of VPN clients can be behind a PIX 501. Is is just limited by the number of hosts (10, 50, Unlimited)?

Hello

Behind a PIX VPN clients. Will you use NAT - T (must). It will be limited only to the number of users (normal users) through the PIX. So if you have a license to use 10 or 50 then the VPN connection is counted in this list.

Connection VPN Client through PIX is not IKE tunnel. They are normal UDP500 and UDP4500 peers.

Vikas

The VPN client VPN connection behind other PIX PIX

I have the following problem:

I wanted to establish the VPN connection the client VPN to PIX on GPRS / 3G, but I didn t have a bit of luck with PIX IOS version 6.2 (2).

So I upgraded PIX to 6.3 (4) to use NAT - T and VPN client to version 4.0.5

I have configured PIX with NAT-T(isakmp nat-traversal 20), but I still had a chance, he would not go through the 1st phase. As soon as I took nat-traversal isakmp off he started working, and we can connect to our servers.

Now, I want to connect to the VPN client behind PIX to our customer PIX network. VPN connection implements without problem, but we can not access the servers. If I configure NAT - T on the two PIX, or only on the customer PIX or only on our PIX, no VPN connection at all.

If I have to connect VPN client behind PIX to the customer's network and you try to PING DNS server for example, on our PIX, I have following error:

305006: failed to create of portmap for domestic 50 CBC protocol translation: dst outside:194.x.x.x 10.10.1.x

194.x.x.x is our customer s address IP PIX

I understand that somewhere access list is missing, but I can not understand.

Of course, I can configure VPN site to site, but we have few customers and take us over their servers, so it'd just connect behind PIX VPN and client connection s server, instead of the first dial-in and then establish a VPN connection.

Can you please help me?

Thank you in advan

The following is extracted from ASK THE DISCUSSION FORUM of EXPERTS with Glenn Fullage of Cisco.

I've cut and pasted here for you to read, I think that the problem mentioned below:

Question:

Hi Glenn,.

Following is possible?

I have the vpn client on my PC, my LAN is protected by a pix. I can launch the vpn client to connect to remote pix. Authenticates the vpn client and the remote pix makes my PC with the assigned ip appropriate to its pool of ip address.

The problem that I am facing is that I can not anything across the pix remote ping from my PC which is behind my pix. Can you please guide me what I have to do to make this work, if it is possible?

My PC has a static ip address assigned with the default gateway appropriate pointing to my s pix inside interface.

Thank you very much for any help provided in advance.

Response from Glenn:

First of all, make sure that the VPN connection works correctly when the remote PC is NOT behind a PIX. If that works fine, but then breaks when put behind a PIX, it is probably that the PIX is PAT, which usually breaks IPSec. Add the following command on your PIX VPN client is behind:

fixup protocol esp-ike

See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/df.htm#wp1067379 for more details.

If it still has issues, you can turn on NAT - T on the remote PIX that ends the VPN, the client and the remote PIX must encapsulate then all IPSec in UDP packets that your PIX will be able to PA correctly. Add the following command on the remote PIX:

ISAKMP nat-traversal

See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/gl.htm#wp1027312 for more details.

NAT - T is a standard for the encapsulation of the UDP packets inot IETF IPSec packets.

ESP IPSec (Protocol that use your encrypted data packets) is an IP Protocol, it is located just above IP, rather than being a TCP or UDP protocol. For this reason, it has no TCP/UDP port number.

A lot of features that make the translation of address of Port (PAT) rely on a single to PAT TCP/UDP source port number ' ing. Because all traffic is PAT would be at the same source address, must be certain uniqueness to each of its sessions, and most devices use the port number TCP/UDP source for this. Because IPSec doesn't have one, many features PAT fail to PAT it properly or at all, and the data transfer fails.

NAT - T is enabled on both devices of the range, they will determine during the construction of the tunnel there is a PAT/NAT device between them, and if they detect that there is, they automatically encapsulate every IPSec packets in UDP packets with a port number of 4500. Because there is now a port number, PAT devices are able to PAT it correctly and the traffic goes normally.

Hope that helps.

termination of VPN client 4.0 on pix 515

I am trying to connect the cisco 4.0 vpn client to a worm of pix 515 6.1 and receive as a result of errors that I guess are the related hashing algorithm but am not sure. Only DES is not enabled 3DES. Config output Cisco post interprets but apparently no error in config.

Journal of VPN client:

Cisco Systems VPN Client Version 4.0 (Rel)

Copyright (C) 1998-2003 Cisco Systems, Inc. All rights reserved.

Customer type: Windows, Windows NT

Running: 5.0.2195

1 10:58:34.890 25/09/03 Sev = Info/4 CM / 0 x 63100002

Start the login process

2 10:58:34.906 25/09/03 Sev = Info/4 CVPND/0xE3400001

Microsoft's IPSec Policy Agent service stopped successfully

3 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100004

Establish a connection using Ethernet

4 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100024

Attempt to connect with the server "x.x.x.226".

5 10:58:35.953 25/09/03 Sev = Info/6 IKE/0x6300003B

Attempts to establish a connection with x.x.x.226.

6 10:58:36.000 25/09/03 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Nat - T), VID (Frag), VID (Unity)) at x.x.x.226

7 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700008

IPSec driver started successfully

8 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

9 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021

Retransmit the last package!

10 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226

11 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021

Retransmit the last package!

12 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226

13 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021

Retransmit the last package!

14 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226

15 10:58:56.093 25/09/03 Sev = Info/4 IKE / 0 x 63000017

Marking of IKE SA delete (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

16 10:58:56.593 25/09/03 Sev = Info/4 IKE/0x6300004A

IKE negotiation to throw HIS (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

17 10:58:56.593 25/09/03 Sev = Info/4 CM / 0 x 63100014

Could not establish the Phase 1 SA with the server 'x.x.x.226' due to the 'DEL_REASON_PEER_NOT_RESPONDING '.

18 10:58:56.593 25/09/03 Sev = Info/5 CM / 0 x 63100025

Initializing CVPNDrv

19 10:58:56.593 25/09/03 Sev = Info/4 IKE / 0 x 63000001

Signal received IKE to complete the VPN connection

20 10:58:56.625 25/09/03 Sev = critique/1 CVPND/0xE3400001

Service Microsoft's IPSec Policy Agent started successfully

21 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

22 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

23 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

24 10:58:57.093 25/09/03 Sev = Info/4 IPSEC/0x6370000A

IPSec driver successfully stopped

Journal of Pix:

crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226

Peer VPN: ISAKMP: approved new addition: ip:x.x.x.194 Total VPN peer: 1

Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 1 Total VPN EEP

RS: 1

Exchange OAK_AG

ISAKMP (0): treatment ITS payload. Message ID = 0

ISAKMP (0): audit ISAKMP transform 1 against the policy of priority 1

ISAKMP: encryption... What? 7?

ISAKMP: hash SHA

ISAKMP: default group 2

ISAKMP: preshared extended auth

ISAKMP: type of life in seconds

ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

ISAKMP: attribute 3584

ISAKMP (0): atts are not acceptable. Next payload is 3

ISAKMP (0): audit ISAKMP transform against the policy of priority 1 2

ISAKMP: encryption... What? 7?

ISAKMP: MD5 hash

ISAKMP: default group 2

ISAKMP: preshared extended auth

ISAKMP: type of life in seconds

ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

ISAKMP: attribute 3584

ISAKMP (0): atts are not acceptable. Next payload is 3

ISAKMP (0): audit ISAKMP transform 3 against the policy of priority 1

ISAKMP: encryption... What? 7?

ISAKMP: hash SHA

ISAKMP: default group 2

ISAKMP: preshared auth

ISAKMP: type of life in seconds

ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

ISAKMP: attribute 3584

ISAKMP (0): atts are not acceptable. Next payload is 3

ISAKMP (0): audit ISAKMP transform 4 against the policy of priority 1

ISAKMP: encryption... What? 7?

ISAKMP: MD5 hash

ISAKMP: default group 2

ISAKMP: preshared auth

ISAKMP: type of life in seconds

ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

ISAKMP: attribute 3584

ISAKMP (0): atts are not acceptable. Next payload is 3

ISAKMP (0): audit ISAKMP transform 5 against the policy of priority 1

ISAKMP: encryption... What? 7?

ISAKMP: hash SHA

ISAKMP: default group 2

ISAKMP: preshared extended auth

ISAKMP: type of life in seconds

ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

ISAKMP: attribute 3584

ISAKMP (0): atts are not acceptable. Next payload is 3

ISAKMP (0): audit ISAKMP transform 6 against the policy of priority 1

ISAKMP: encryption... What? 7?

ISAKMP: MD5 hash

ISAKMP: default group 2

ISAKMP: preshared extended auth

ISAKMP: type of life in seconds

ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

ISAKMP: attribute 3584

ISAKMP (0): atts are not acceptable. Next payload is 3

ISAKMP (0): audit ISAKMP transform 7 against the policy of priority 1

ISAKMP: encryption... What? 7?

ISAKMP: hash SHA

ISAKMP: default group 2

ISAKMP: preshared auth

ISAKMP: type of life in seconds

ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

ISAKMP: attribute 3584

ISAKMP (0): atts are not acceptable. Next payload is 3

ISAKMP (0): audit ISAKMP transform 8 against the policy of priority 1

ISAKMP: encryption... What? 7?

ISAKMP: MD5 hash

ISAKMP: default group 2

ISAKMP: preshared auth

ISAKMP: type of life in seconds

ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

ISAKMP: attribute 3584

ISAKMP (0): atts are not acceptable. Next payload is 3

ISAKMP (0): audit ISAKMP transform 9 against the policy of priority 1

ISAKMP: 3DES-CBC encryption

ISAKMP: hash SHA

ISAKMP: default group 2

ISAKMP: preshared extended auth

ISAKMP: type of life in seconds

ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4

crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226

Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP

RS: 1

Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP

RS: 1

crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226

Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP

RS: 1

Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP

RS: 1

ISAKMP (0): retransmission of phase 1...

ISAKMP (0): retransmission of phase 1...

ISAKMP (0): delete SA: src x.x.x.194 dst x.x.x.226

ISADB: Reaper checking HIS 0x80db91c8, id_conn = 0 DELETE IT!

Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 0 Total of VPN EEP

RS: 1

Peer VPN: ISAKMP: deleted peer: ip:x.x.x.194 VPN peer Total: 0

ISAKMP: Remove the peer node for x.x.x.194

Thanks for any help

Hello

Pix isakmp policy should have DES, MD5, and group 2 for the 4.x to connect Cisco VPN client, these are proposals that the client sends to the server...

http://www.Cisco.com/univercd/CC/TD/doc/product/VPN/client/rel4_0/admin_gd/vcach6.htm#1157757

This link will show you IKE proposals be configured on the PIX (VPN server)

Arthur

Itineraries other nets will be lost when using the vpn client?

I have a very general question. I intend to implement a security solution for the extranet partners to connect to our intranet using VPN client. IPSec will close on the external interface of the Cisco PIX firewall v6.3.

Now, my consirn is, I downloaded the vpn client to test but I saw no advance settings to define what network traffic will pass through the IPSec tunnel and which will be routed normally. Is it by default all traffic passing through VPN? Is that what it means if there are other networks using their default route, they will not be able to achieve? (i.e. the Internet).

Thank you.

That would depend on how you set up the PIX. You can allow the VPN to your site and access to the Internet at the same time. This is called the split tunneling. It is configurable on the PIX, not the customer.

This link might help you get started, but I'm sure that there stronger links.

http://www.Cisco.com/en/us/customer/products/sw/secursw/ps2120/products_command_reference_chapter09186a00800ec9ec.html

PIX: Cisco VPN Client connects but no routing

Hello

We have a Cisco PIX 515 with software 7.1 (2). He accepts Cisco VPN Client connections with no problems, but no routing does to internal networks directly connected to the PIX. For example, my PC is affected by the IP 172.16.2.57 and then ping does not respond to internal Windows server 172.16.0.12 or trying to RDP. The most irritating thing is that these attempts are recorded in the system log, but always ended with "SYN timeout", as follows:

2009-01-06 23:23:01 Local4.Info 217.15.42.214% 302013-6-PIX: built 3315917 for incoming TCP connections (172.16.2.57/1283) outside:172.16.2.57/1283 inside: ALAI2 / 3389 (ALAI2/3389)

2009-01-06 23:23:31 Local4.Info 217.15.42.214% 302014-6-PIX: TCP connection disassembly 3315917 for outside:172.16.2.57/1283 inside: ALAI2 / 3389 duration 0:00:30 bytes 0 SYN Timeout

2009-01-06 23:23:31 Local4.Debug 217.15.42.214% 7-PIX-609002: duration of disassembly-outside local host: 172.16.2.57 0:00:30

We tried to activate and deactivate "nat-control", "permit same-security-traffic inter-interface" and "permit same-security-traffic intra-interface", but the results are the same: the VPN connection is successfully established, but remote clients cannot reach the internal servers.

I enclose the training concerned in order to understand the problem:

interface Ethernet0

Speed 100

full duplex

nameif outside

security-level 0

IP address xx.yy.zz.tt 255.255.255.240

!

interface Ethernet1

nameif inside

security-level 100

172.16.0.1 IP address 255.255.255.0

!

access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.255.0 172.16.2.56 255.255.255.248

!

access extensive list ip 172.16.0.0 outside_cryptomap_dyn_20 allow 255.255.255.0 172.16.2.56 255.255.255.248

!

VPN_client_group_splitTunnelAcl list standard access allowed 172.16.0.0 255.255.255.0

!

IP local pool pool_vpn_clientes 172.16.2.57 - 172.16.2.62 mask 255.255.255.248

!

NAT-control

Global xx.yy.zz.tt 12 (outside)

NAT (inside) 0-list of access inside_nat0_outbound

NAT (inside) 12 172.16.0.12 255.255.255.255

!

internal VPN_clientes group strategy

attributes of Group Policy VPN_clientes

xxyyzz.NET value by default-field

internal VPN_client_group group strategy

attributes of Group Policy VPN_client_group

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list VPN_client_group_splitTunnelAcl

xxyyzz.local value by default-field

!

I join all the details of the cryptographic algorithms because the VPN is successfully completed, as I said at the beginning. In addition, routing tables are irrelevant in my opinion, because the inaccessible hosts are directly connected to the internal LAN of the PIX 515.

Thank you very much.

can you confirm asa have NAT traversal allow otherwise, activate it in asa and vpn clients try again.

PIX / ASA 7.1 and earlier versions

PIX (config) #isakmp nat-traversal 20

PIX / ASA 7.2 (1) and later versions

PIX (config) #crypto isakmp nat-traversal 20

VPN Client connection terminated

I am new to Cisco PIX and I'm having a problem with the removal of the connections. We use a 515e on 6.2 and my laptops use VPN Client 4.0 and Radius to IAS on W2K3 Server. About 30 minutes, a window appears saying "secure VPN connection is completed by a peer. "Reason: (reason unspecified peer). I've combed through the configuration settings and the settings of the Cisco and my connection on the Radius Server and am unable to find anything to help. Any help would be appreciated.

Thank you

Warren

On if the PIX515 you do a 'show vpngroup' which is the ' time max "setting configured for? If it is not configured, you can do a max of vpngroup-time for the clients of the group. You can also set the idle max here too. In troubleshooting, maybe set to 3600 seconds (1 hour) to see if you are disconnected. Then adjust your idle down time (you can set it to 0 if ever you want clients idel time out) and see what happens.

Matt

VPN clients are unable to access sites that are above a link from site to site

could someone please give me some direction, I have a set of vpn clients set up on a pix and I'm trying to give them access to a network that is connected via a link from a site that is set up on the same pix. so, basically, that it receives information from VPN client on the same interface, it built the tunnel from site to site, I've heard that's not possible is that the case. Or it can be fixed, I can provide diagrams and if necessary conf files.

You are right. You need a minimum of 7.0 for the feature you're looking for.

Kind regards

Arul

* Please note all useful messages *.

Layman to ASA 5505 vpn of the native vpn client internet, tcp 1723

Hi all

I am setting up this asa for connect users at home to my network using vpn clients from microsoft to the native address with windows xp on the internet.

This asa have, on the outside interface an ip public Internet and inside Board have set up in the network of 192.168.0.x and I want to access this network of internet users using native vpn clients.

I tested with a pc connected directly to the external interface and works well, but when I connect this interface to the internet and tried to connect to the vpn user I can see it in the newspapers and unable to connect with error 800.

Request TCP and eliminated from "public_ip_client/61648" outdoors: publicip_outside_interface / 1723 "

Can help me please?, very thanks in advance!

(running configuration)

: Saved

:

ASA Version 8.4 (3)

!

ciscoasa hostname

activate the password * encrypted

passwd * encrypted

names of

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

interface Vlan1

nameif inside

security-level 100

the IP 192.168.0.1 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP address publicinternetaddress 255.255.255.0

!

passive FTP mode

permit same-security-traffic inter-interface

permit same-security-traffic intra-interface

network obj_any object

subnet 0.0.0.0 0.0.0.0

network gatewayono object

Home gatewayofinternetprovideraccess

Description salida gateway ono

service remotointerno object

service destination tcp 3389 eq

Remote description

network pb_clienteing_2 object

host 192.168.0.15

Description Pebble client food bowl 2

service remotoexternopebble object

Service tcp destination eq 5353

Description remotoexterno

network actusmon object

Home 192.168.0.174

Description web news monitor

the Web object service

Service tcp destination eq www

Description 80

irdeto network object

Home 192.168.0.31

Irdeto description

network nmx_mc_p object

host 192.168.0.60

Main description of NMX multichannel

network nmx_mc_r object

Home 192.168.0.61

Description NMX multichannel reserva

network tarsys object

host 192.168.0.10

Tarsys description

network nmx_teuve object

host 192.168.0.30

Nmx cabecera teuve description

tektronix network object

host 192.168.0.20

Tektronix vnc description

vnc service object

destination eq 5900 tcp service

Description access vnc

service exvncnmxmcr object

Service tcp destination EQ. 5757

Access vnc external nmx mc figurative description

service exvncirdeto object

Service tcp destination eq 6531

Description access vnc external irdeto

service exvncnmxmcp object

Service tcp destination eq 5656

service exvnctektronix object

Service tcp destination eq 6565

service exvncnmxteuve object

Service tcp destination eq 6530

ssh service object

tcp destination eq ssh service

service sshtedialexterno object

Service tcp destination eq 5454

puertosabiertos tcp service object-group

Remotedesktop description

EQ port 3389 object

object-group Protocol TCPUDP

object-protocol udp

object-tcp protocol

the DM_INLINE_NETWORK_1 object-group network

network-object object irdeto

network-object object nmx_mc_p

network-object object nmx_mc_r

network-object object nmx_teuve

tektronix network-object

object-group service udp vpn

EQ port 1723 object

DM_INLINE_TCP_1 tcp service object-group

EQ object of the https port

EQ pptp Port object

the DM_INLINE_NETWORK_2 object-group network

network-object object actusmon

network-object object tarsys

inside_access_in remotointerno permitted object extended access list a whole

inside_access_in list extended access allowed object ssh a whole

inside_access_in list extended access allowed object-group TCPUDP any any eq www

inside_access_in list extended access permit icmp any one

inside_access_in list extended access allowed object vnc a whole

inside_access_in of access allowed any ip an extended list

outside_access_in list extended access allowed object remotointerno any object pb_clienteing_2

outside_access_in list extended access allowed object-group TCPUDP any object actusmon eq www

access-list outside_access_in note Acceso tedial ssh

outside_access_in list extended access permit tcp any object tarsys eq ssh

outside_access_in list extended access allowed object vnc any object-group DM_INLINE_NETWORK_1

outside_access_in list extended access permit tcp any any DM_INLINE_TCP_1 object-group

outside_access_in list extended access deny icmp a whole

access-list standard corporate allowed 192.168.0.0 255.255.255.0

Split-Tunnel-ACL access-list allowed standard 192.168.0.0 255.255.255.0

pager lines 24

Enable logging

monitor debug logging

logging of debug asdm

Debugging trace record

Within 1500 MTU

Outside 1500 MTU

IP local pool 192.168.0.100 - 192.168.0.110 mask 255.255.255.0 clientesvpn

IP local pool clientesvpn2 192.168.1.120 - 192.168.1.130 mask 255.255.255.0

ICMP unreachable rate-limit 1 burst-size 1

ICMP allow any inside

ICMP allow all outside

don't allow no asdm history

ARP timeout 14400

NAT (exterior, Interior) static source any service of actusmon of interface static destination Web one-way Web interface

NAT (exterior, Interior) static source to any destination interface interface static tarsys one-way sshtedialexterno ssh service

NAT (exterior, Interior) static source any destination interface interface static one-way pb_clienteing_2 service remotoexternopebble remotointerno

NAT (exterior, Interior) static source any destination interface interface static irdeto one-way exvncirdeto vnc service

NAT (exterior, Interior) static source any destination interface interface static one-way vnc exvncnmxmcp service nmx_mc_p

NAT (exterior, Interior) static source any destination interface interface static one-way vnc exvncnmxmcr service nmx_mc_r

NAT (exterior, Interior) static source any destination interface interface static one-way vnc exvncnmxteuve service nmx_teuve

NAT (exterior, Interior) static source any destination interface interface static tektronix one-way exvnctektronix vnc service

NAT (all, outside) interface dynamic source DM_INLINE_NETWORK_2

inside_access_in access to the interface inside group

Access-group outside_access_in in interface out by-user-override

Route outside 0.0.0.0 0.0.0.0 gatewayinternetprovideracces 1

dynamic-access-policy-registration DfltAccessPolicy

identity of the user by default-domain LOCAL

EOU allow none

local AAA authentication attempts 10 max in case of failure

Enable http server

http 192.168.0.0 255.255.255.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

No vpn sysopt connection permit

Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

Crypto ipsec transform-set esp-3des esp-md5-hmac ikev1 clientewindowsxp

IKEv1 crypto ipsec transform-set clientewindowsxp transport mode

Crypto ipsec transform-set ikev1 L2TP-IKE1-Transform-Set esp - aes esp-sha-hmac

Crypto ipsec ikev1 transit mode L2TP-IKE1-Transform-Set transform-set

Crypto ipsec ikev2 ipsec-proposal OF

encryption protocol esp

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 proposal ipsec 3DES

Esp 3des encryption protocol

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 ipsec-proposal AES

Esp aes encryption protocol

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 ipsec-proposal AES192

Protocol esp encryption aes-192

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 AES256 ipsec-proposal

Protocol esp encryption aes-256

Esp integrity sha - 1, md5 Protocol

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 1 set transform-set clientewindowsxp ikev1

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 1jeu ikev2 AES256 AES192 AES 3DES ipsec-proposal OF

Crypto-map dynamic L2TP - map 10 set transform-set L2TP-IKE1-Transform-Set ikev1

inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

inside crypto map inside_map interface

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

Crypto map L2TP - VPN - dynamic 20-isakmp ipsec L2TP-map map

L2TP-VPN-card interface card crypto outside

Crypto ca trustpoint _SmartCallHome_ServerCA

Configure CRL

IKEv2 crypto policy 1

aes-256 encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 10

aes-192 encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 20

aes encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 30

3des encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 40

the Encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

Crypto ikev2 activate out of service the customer port 443

trustpoint to ikev2 crypto Ingeniería remote access

Crypto ikev1 allow inside

Crypto ikev1 allow outside

IKEv1 crypto policy 5

preshared authentication

3des encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 10

authentication crack

aes-256 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 20

authentication rsa - sig

aes-256 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 30

preshared authentication

aes-256 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 40

authentication crack

aes-192 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 50

authentication rsa - sig

aes-192 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 60

preshared authentication

aes-192 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 70

authentication crack

aes encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 80

authentication rsa - sig

aes encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 90

preshared authentication

aes encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 100

authentication crack

3des encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 110

authentication rsa - sig

3des encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 130

authentication crack

the Encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 140

authentication rsa - sig

the Encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 150

preshared authentication

the Encryption

sha hash

Group 2

life 86400

Telnet 192.168.0.0 255.255.255.0 inside

Telnet timeout 5

SSH timeout 5

Console timeout 0

dhcpd dns 8.8.8.8

dhcpd outside auto_config

!

dhcpd address 192.168.0.5 - 192.168.0.36 inside

dhcpd dns 8.8.8.8 8.8.4.4 interface inside

dhcpd auto_config outside interface inside

dhcpd allow inside

!

no basic threat threat detection

no statistical access list - a threat detection

no statistical threat detection tcp-interception

SSL-trust Ingeniería out point

WebVPN

tunnel-group-list activate

internal DefaultRAGroup group strategy

attributes of Group Policy DefaultRAGroup

WINS server no

Server 192.168.0.1 DNS value

Protocol-tunnel-VPN l2tp ipsec

by default no

attributes of Group Policy DfltGrpPolicy

value of server DNS 8.8.8.8

L2TP ipsec VPN-tunnel-Protocol ikev1, ikev2

internal engineering group policy

attributes of Ingeniería group policy

Protocol-tunnel-VPN l2tp ipsec

by default no

L2TP-policy group policy interns

attributes of L2TP-policy-group policy

value of server DNS 8.8.8.8

Protocol-tunnel-VPN l2tp ipsec

Split-tunnel-policy tunnelspecified

Split-tunnel-network-list value Split-Tunnel-ACL

Intercept-dhcp enable

username, password Ingeniería 4fD/5xY/6BwlkjGqMZbnKw is encrypted nt privilege 0

Ingeniería username attributes

VPN-group-policy Ingeniería

password rjuve SjBNOLNgSkUi5KWk/TUsTQ user name is nt encrypted

attributes global-tunnel-group DefaultRAGroup

address clientesvpn pool

address clientesvpn2 pool

authentication-server-group (outside LOCAL)

LOCAL authority-server-group

Group Policy - by default-L2TP-policy

authorization required

IPSec-attributes tunnel-group DefaultRAGroup

IKEv1 pre-shared-key *.

tunnel-group DefaultRAGroup ppp-attributes

No chap authentication

ms-chap-v2 authentication

!

class-map inspection_default

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

!

context of prompt hostname

anonymous reporting remote call

Cryptochecksum:59b54f1d10fe829aeb47bafee57ba95e

: end

don't allow no asdm history

I ramon I guess that service policy is not applied in the firewall. So it does not not trust other than the same audience segment.

Apply like this.

global_policy global service policy.

because according to the configs old, I see that the policy has not been applied. Please let me know the results.

Please rate if the given info can help.

Authentication failure - 5505 8.3 configuration to windows server RAIDUS vpn client

Hello

I'm trying to put up a 5505 (8.3 running) so that I can use vpn client through the RADIUS authentication

I set up a new local RAIDUS windows box and used the ASDM Assistant and a few other installation guides the 5505.

I get the following error:

INFO: Attempt to <10.0.0.92>IP address authentication test (timeout: 12 seconds)

ERROR: Authentication rejected: failure of the AAA

any help would be greatly appreciated

Here is my config sanitized:

lit5505-02 # sh run

: Saved

:

ASA Version 8.3 (1)

!

hostname lit5505-02

no names

!

interface Vlan1

nameif inside

security-level 100

10.0.0.100 IP address 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP address

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

banner motd ****************************************

Banner motd No. unauthorized access is allowed

banner motd ****************************************

passive FTP mode

DNS server-group DefaultDNS

domain name

network obj_any object

subnet 0.0.0.0 0.0.0.0

object network lotus_notes

host 10.0.0.3

network sonicwall_ssl_2000 object

Home 10.0.0.12

network of the NETWORK_OBJ_10.0.0.0_24 object

10.0.0.0 subnet 255.255.255.0

network of the ABD_LAN object

10.7.0.0 subnet 255.255.0.0

network of the LIT_LAN object

10.0.0.0 subnet 255.255.0.0

network of the LIT_LAN_vlan101 object

subnet 10.0.1.0 255.255.255.0

network of the LIT_LAN_vlan102 object

10.0.2.0 subnet 255.255.255.0

network of the LIT_LAN_vlan103 object

subnet 10.0.3.0 255.255.255.0

network of the LIT_LAN_vlan104 object

10.0.4.0 subnet 255.255.255.0

network of the LIT_LAN_vlan105 object

10.0.5.0 subnet 255.255.255.0

network of the LIT_LAN_vlan106 object

10.0.6.0 subnet 255.255.255.0

network of the LIT_LAN_vlan109 object

10.0.9.0 subnet 255.255.255.0

network of the LIT_LAN_vlan112 object

10.0.112.0 subnet 255.255.255.0

network of the LIT_LAN_vlan114 object

10.0.114.0 subnet 255.255.255.0

network of the LIT_LAN_vlan120 object

10.0.20.0 subnet 255.255.255.0

network of the LIT_LAN_vlan121 object

10.0.21.0 subnet 255.255.255.0

network of the LIT_LAN_vlan100 object

10.0.0.0 subnet 255.255.255.0

network of the LIT_LAN_vlan107 object

10.0.7.0 subnet 255.255.255.0

network of the LIT_LAN_vlan108 object

10.0.8.0 subnet 255.255.255.0

network of the BER_vlan1 object

subnet 10.8.0.0 255.255.255.0

the LIT_VLANS object-group network

network-object, object LIT_LAN_vlan100

network-object, object LIT_LAN_vlan101

network-object, object LIT_LAN_vlan102

network-object, object LIT_LAN_vlan103

network-object, object LIT_LAN_vlan104

network-object, object LIT_LAN_vlan105

network-object, object LIT_LAN_vlan106

network-object, object LIT_LAN_vlan107

network-object, object LIT_LAN_vlan108

network-object, object LIT_LAN_vlan109

network-object, object LIT_LAN_vlan112

network-object, object LIT_LAN_vlan114

network-object, object LIT_LAN_vlan120

network-object, object LIT_LAN_vlan121

the BER_VLANS object-group network

network-object, object BER_vlan1

access list off - in extended permit icmp any one

out-in access-list extended permit tcp any object sonicwall_ssl_2000 eq https

access-list out-in extended permit tcp any eq smtp lotus_notes object

access list-based ip allowed any one

outside_1_cryptomap list extended access permitted ip LIT_VLANS object ABD_LAN object-group

outside_2_cryptomap list extended access permitted ip object-group LIT_VLANS-group of objects BER_VLANS

pager lines 24

asdm of logging of information

Within 1500 MTU

Outside 1500 MTU

ICMP unreachable rate-limit 1 burst-size 1

don't allow no asdm history

ARP timeout 14400

NAT static LIT_VLANS LIT_VLANS destination (indoor, outdoor) static source ABD_LAN ABD_LAN

NAT static LIT_VLANS LIT_VLANS destination (indoor, outdoor) static source BER_VLANS BER_VLANS

!

network obj_any object

NAT dynamic interface (indoor, outdoor)

object network lotus_notes

Static NAT (indoor, outdoor)

network sonicwall_ssl_2000 object

Static NAT (indoor, outdoor)

Access-group all-out in the interface inside

out-in access-group in external interface

Route outside 0.0.0.0 0.0.0.0

Route inside 10.0.1.0 255.255.255.0 10.0.0.254 1

Route inside 10.0.2.0 255.255.255.0 10.0.0.254 1

Route inside between 10.0.3.0 255.255.255.0 10.0.0.254 1

Route inside 10.0.4.0 255.255.255.0 10.0.0.254 1

Route inside 10.0.5.0 255.255.255.0 10.0.0.254 1

Route inside 10.0.6.0 255.255.255.0 10.0.0.254 1

Route inside 10.0.7.0 255.255.255.0 10.0.0.254 1

Route inside 10.0.8.0 255.255.255.0 10.0.0.254 1

Route inside 10.0.9.0 255.255.255.0 10.0.0.254 1

Route inside 10.0.20.0 255.255.255.0 10.0.0.254 1

Route inside 10.0.21.0 255.255.255.0 10.0.0.254 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

dynamic-access-policy-registration DfltAccessPolicy

RADIUS protocol AAA-server litvms03

litvms03 AAA-server (inside) host 10.0.0.92

key *.

RADIUS-common-pw *.

the ssh LOCAL console AAA authentication

Enable http server

http 10.0.0.0 255.255.0.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

card crypto outside_map 1 match address outside_1_cryptomap

card crypto outside_map 1 set pfs Group1

map 1 set outside_map crypto peer

card crypto outside_map 1 set of transformation-ESP-3DES-SHA

card crypto outside_map 2 match address outside_2_cryptomap

card crypto outside_map 2 pfs Group1 set

card crypto outside_map 2 defined peer

card crypto outside_map 2 game of transformation-ESP-3DES-SHA

outside_map interface card crypto outside

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 86400

No encryption isakmp nat-traversal

Telnet timeout 5

SSH 10.0.0.0 255.255.0.0 inside

SSH 10.7.0.0 255.255.0.0 inside

SSH timeout 5

SSH version 2

Console timeout 0

management-access inside

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

NTP server 216.14.98.234 prefer external source

NTP server 204.15.208.61 prefer external source

WebVPN

internal jdr_littleport_employee_vpn group policy

attributes of the strategy of group jdr_littleport_employee_vpn

banner value

value of 10.0.0.8 WINS server 10.100.1.141

value of 10.0.0.8 DNS server 10.100.1.141

Split-tunnel-policy tunnelall

jdrcables.com value by default-field

Split-dns value jdrcables.com

IPv6 address pools no

type of tunnel-group ipsec-l2l

Tunnel ipsec-attributes group

pre-shared key *.

type of tunnel-group ipsec-l2l

Tunnel ipsec-attributes group

pre-shared key *.

!

!

context of prompt hostname

Cryptochecksum:6d1868630c83f17fe0c7de41006a1526

: end

Rich

I have checked the road conditions but missed the VIRTUAL LAN address. Sorry about that.

I'm glad to see that you solved the problem and am not surprised that the question seems to have been some incompatible in the serttings server. I think you should be able to close the thread based on your response. Give it a try.

HTH

Rick

VPN - PC (vpn client) problem-> router-> (site to site vpn)-> local network

Hello

is it possible to install?

I have a pc and I want to connect to the Remote LAN.

PC (using vpn client) - vpn (internet)---> ROUTER1 - a vpn (MPLS network)---> ROUTER2---> SERVER site

How can I connect to a remote server? Is there an easy way?

I did the configuration of the vpn client (I can connect ROUTER1 and access a LAN via vpn with 192.168.1.x), but I can't connect to the server, even if I set the subnet (192.168.1.x) under the access list of site to site vpn (access list for traffic that must pass between ROUTER1 and ROUTER2).

Please advise! Thanks in advance.

Looks like I've not well explained.

On ROUTER1

===================

1 ACL VNC_acl is used to split tunnel, so you should include IP server_NET it NOT vpn IP pool.

2 ACL najavorbel is used to set the lan lan traffic between ROUTER1 and ROUTER2, 2 you should inlcude

IP 192.168.133.0 allow 0.0.0.255 0.0.0.255

You must change the crypto ROUTER2 ACL of the minor or the najavorbel of the ACL

The other way to is to the client VPN NAT IP to a local area network lan IP ROUTER1, in this way, you don't need any changes on ROUTER2. But I have to take a look at your configuration to make the suggestion.

Cisco VPN Client behind PIX 515E,-> VPN concentrator

I'm trying to configure a client as follows:

The user is running Cisco VPN Client 4.0. They are behind a 6.1 PIX 515E (4), and I need to connect to a VPN concentrator located outside of our network. We use PAT for address translation. As far as I know, to allow ipsec through Firewall 1 tunnel, I need to upgrade the pix to 6.3 and activate "fixup protocol esp-ike.

Is there another way to do this? I am also curious to know how much more easy/better this will work if we were dealing with pptp.

You don't necessarily need to fixup protocol esp-ike active. The remote Hub there encapsulation NAT - T enabled so that clients behind the NAT can run?

VPN client behind ok asa pix but no asa

Hi all

I was faced with a newly installed asa5505 couple. We can use the vpnclient in devices, but not behind another asa. Behind the asa same we can vpn for previous installations of pix. But when we go to other asa installs, we get the regular creation of translation failed for protocol 50.

We have activated, isakmp, nat-traversal, udp 4500 and udp 10000. If the fault is at the other end, even if the error shows in this end?

Anyone who is willing to help me with this?

see you soon / Peter

You do not allow protocol 50 - ESP through the firewall. The remote end VPN are trying to create a VPN in mode 'Hand' is not "Aggressive" mode as VPN clients.

Add the below and test again: -.

permit for outside_access_in to access extensive list of 6 esp a whole line

HTH.

Using VPN Client coming out behind a PIX

Similar Questions

Maybe you are looking for