PIX: Cisco VPN Client connects but no routing

Similar Questions

• Cisco VPN Client connected, but no secure way.

  Hello

  I can connect to a VPN server smoothly, but once connected, I'm not able to reach all local resources. When I looked at the stats of customer VPN, it shows only a single route in 'Details of the route--> secure routes', 1.1.1.1 255.255.255.255. This is the reason why I can't access any resource. This could be the cause of this problem? How can I secure roads announcing cisco customer? I don't have access to the server, but I will ask the person who can make changes.

  Thank you.

  Kind regards

  Shivani

  Shivani,

  Split tunneling is what you're looking for, it will affect your secure routes.

  Marcin

• Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

  I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

  Thank you

  interface Ethernet0/0

  Speed 100

  full duplex

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.240

  !

  interface Ethernet0/1

  Speed 100

  full duplex

  nameif inside

  security-level 100

  IP 10.88.10.254 255.255.255.0

  !

  interface Management0/0

  Shutdown

  nameif management

  security-level 0

  no ip address

  !

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  network of the PAT_to_Outside_ClassA object

  10.88.0.0 subnet 255.255.0.0

  network of the PAT_to_Outside_ClassB object

  subnet 172.16.0.0 255.240.0.0

  network of the PAT_to_Outside_ClassC object

  Subnet 192.168.0.0 255.255.240.0

  network of the LocalNetwork object

  10.88.0.0 subnet 255.255.0.0

  network of the RemoteNetwork1 object

  Subnet 192.168.0.0 255.255.0.0

  network of the RemoteNetwork2 object

  172.16.10.0 subnet 255.255.255.0

  network of the RemoteNetwork3 object

  10.86.0.0 subnet 255.255.0.0

  network of the RemoteNetwork4 object

  10.250.1.0 subnet 255.255.255.0

  network of the NatExempt object

  10.88.10.0 subnet 255.255.255.0

  the Site_to_SiteVPN1 object-group network

  object-network 192.168.4.0 255.255.254.0

  object-network 172.16.10.0 255.255.255.0

  object-network 10.0.0.0 255.0.0.0

  outside_access_in deny ip extended access list a whole

  inside_access_in of access allowed any ip an extended list

  11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

  outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

  mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

  NAT static NatExempt NatExempt of the source (indoor, outdoor)

  NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

  NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

  !

  network of the PAT_to_Outside_ClassA object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassB object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassC object

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_access_in in interface outside

  inside_access_in access to the interface inside group

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  dynamic-access-policy-registration DfltAccessPolicy

  Sysopt connection timewait

  Service resetoutside

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto-map dynamic dynmap 10 set pfs

  Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

  life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

  Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

  Crypto-map dynamic dynmap 10 the value reverse-road

  card crypto mymap 1 match address outside_1_cryptomap

  card crypto mymap 1 set counterpart x.x.x.x

  card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

  card crypto mymap 86400 seconds, 1 lifetime of security association set

  map mymap 1 set security-association life crypto kilobytes 4608000

  map mymap 100-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  crypto isakmp identity address

  Crypto isakmp nat-traversal 30

  Crypto ikev1 allow outside

  IKEv1 crypto ipsec-over-tcp port 10000

  IKEv1 crypto policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 50

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  preshared authentication

  aes-256 encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  Console timeout 0

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal BACKDOORVPN group policy

  BACKDOORVPN group policy attributes

  value of VPN-filter 11

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelall

  BH.UK value by default-field

  type tunnel-group BACKDOORVPN remote access

  attributes global-tunnel-group BACKDOORVPN

  address pool Admin_Pool

  Group Policy - by default-BACKDOORVPN

  IPSec-attributes tunnel-group BACKDOORVPN

  IKEv1 pre-shared-key *.

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group ipsec-attributes x.x.x.x

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  Excellent.

  Evaluate the useful ticket.

  Thank you

  Rizwan James

• VPN client connected but no ping nor access to privat network

  Hello

  I have a 1802w installed, a VPN client that can connect to the router and L2L connection, which works very well.

  On the router, I see that the client is connected, but no traffic passes. In sh crypto ipsec, I see that traffic is decrypted, but no packtets are encypted.

  Can someone point me in the right direction? I have the confs and debugs attached. Thanks for the help in advance.

  Erich

  Erich,

  Looking at your configuration, two things:

  1 - is the current running configuration. I see your Tunnel L2L is configured with an address of correspondence of 101, but I don't see a 101 ACL set on the router.

  2. your Split Tunnel must be reconfigured. Which means, the source and destination must be exchanged.

  SplitList extended IP access list

  permit ip 192.168.2.0 0.0.0.255 192.168.111.0 0.0.0.255

  Split Tunneling

  http://www.Cisco.com/en/us/Tech/tk59/technologies_configuration_example09186a00800a393b.shtml#Con4

  Also, the IP address pool you assign to clients, ensure that they are not part of a LAN on your side. If so, you can then run in routing problems.

  Kind regards

  Arul

  * Please note all useful messages *.

• Linksys Cisco VPN Client connection drops

  I have a Linksys BEFVP41 V2. I have a PC running Windows XP SP2 with customer VPN Cisco 5.0.00.0340. I have a problem when I log in the VPN client with my employer network. It seems to be ok. No problem to do the job, hit their proxy server, etc.. All of a sudden, the connection drops. It seems to 'freeze' the network. No surfing, without PuTTY. Sometimes 5 minutes after the connection or 3 hours later. I have to disconnect the VPN connection, and then reconnect. What could be the problem? My MTU is set to 1432. The Windows Firewall has exceptions for ports 10000, 4500 and 62515. I have a network in place at 172.20.x.x... not the default or typical 10.x.x.x network. Firmware is 1.01.04 on the router.

  
  

• Cisco VPN Client anything cannot access through VPN on an ASA5505 8.4

  Hello

  Completely new to Cisco ASA and the need to get this working ASAP.

  8.4 (1) ASA 5505 is the secondary FW and I need to authorize all out and block everything coming, but for the VPN clients.  Since a jerk of Cisco, I used the ASDM and it's sorcerers to make this work, which may explain my situation.

  192.168.101.0/24 is the local network

  192.168.101.5 is the IP of ASA

  192.168.101.2 is the primary FW (and the default gateway for servers, I have to access through the VPN)

  10.10.101.0/24 is the VPN IP range (this can be what you want, I'm not married to it somehow)

  My Cisco VPN Client connects to the ASA and receives 10.10.101.1 IP address, but I get no connectivity to the ASA or any other 192.168.101.x or service server (tried RDP, telnet, ping, etc.)

  Configuration file is attached.

  Help pretty please!

  Thank you.

  Did you add a route for the VPN Pool on the main firewall to the ASA?

  Best regards

  Peer

  Sent by Cisco Support technique iPad App

• Allow Cisco VPN Client through the firewall?

  Hello

  How can I allow a cisco VPN client work from the inside of our network to an external IP address?

  We have customers who wish to make use of their Cisco VPN Client companies but our ASA blocks I think?

  Also (sorry to ask) a friend in South America is having the same problem but I am not hink they use Cisco, is there a default port used by the client to Cisco? then I can send this info?

  Thank you

  Generally, the ASA will allow the IPSEC from the inside to outside traffic. This is when you want it came outside and connect to you - this is where it gets creative. You restrict outgoing traffic at all? You deny all ip/tcp/udp outgoing?

  But may depend on if the remote end is compaitable NAT - T, and if they have configured. Another question would be how they allow VPN traffic go?

• Receive message "Validation of C:\WINDOWS\System32\VSINIT.dll failure" error message when trying to run Cisco VPN Client.

  windows\system32\vsinit.dll

  I try to run CISCO "VPN Client" connect from my PC at home for my work PC.

  Then, I get a message:

  Validation failed for C:\WINDOWS\System32\VSINIT.dll

  Any ideas?

  Martin

  Hello

  Run the checker system files on the computer. Link, we can see: Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe): http://support.microsoft.com/kb/310747

  Note that: if he asks you the service pack CD, follow these steps from the link: you are prompted to insert a Windows XP SP2 CD when you try to run the tool on a Windows XP SP2 computer system File Checker: http://support.microsoft.com/kb/900910 (valid for Service pack 3)

  If the steps above is not enough of it please post your request in the TechNet forum for assistance: http://social.technet.microsoft.com/Forums/en/category/windowsxpitpro

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• Cisco vpn client to connect but can not access to the internal network

  Hi all

  I have a VPN configured on cisco 5540. My vpn was working fine, but suddenly there is a question that the cisco vpn client to connect but can not access to the internal network

  Any help would be much appreciated.

  Hi Samir,

  I suggest that you go to the ASA and check the configuration to make sure that it complies with the requirements according to the reference below link:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  (The link above includes split tunneling, but this is just an option.

  Please paste the output of "sh cry ipsec his" here so that we can check if phase 2 is properly trained. I would say as you go to IPSEC vpn client on your PC and check increment in packets sent and received in the window 'status '.

  Let me know if this can help,

  See you soon,.

  Christian V

• Cisco VPN client, PIX, and proxy

  Hi.I have problem in my company. We have users that go through a proxy server located in the DMZ of a PIX to the internet (allowed through the ACL of the DMZ on the outside, etc.). Which works very well.

  The problem arises when they use a Cisco VPN client to connect to another company, and they can no longer access the Internet, but may work via VPN to a remote site (client has been authorized by the Cisco PIX). Everything returns to normal when they no longer use the VPN client.

  Any ideas why this would happen?

  Without the proxy, browsing the internet via the vpn connection, or split tunnel is configured and you are leaving locally. If split tunnel is configured, the ip address of proxy server can overlap with the remote protected network.

  Fortunately, it is easy for you to know how the vpn is configured, just check the route details of vpn client statistics tab.

  Verify that the routing table local pc will also help you to solve this problem.

• Routing issue of Cisco VPN Client ASA

  Hi, I use a Barracuda NG for firewalls and I would use a Cisco ASA 5505 for VPN Client connections. But I have the problem that I can't get a connection to the VPN PC connected to the internal network. But I can reach the VPN connected PC from the inside. Here is a diagram of my network:

  cisco_asa_prob.jpg

  

  Here the IP Configuration and the routing of the Barracuda firewall table:

  screen_shot_2014-08 - 12_at_16.01.42.png

  

  I have a route on the Barracuda NG to the 10.10.10.0/24 network VPN Client on eth0.

  The 192.168.1.0/24 LAN I ping the Client comes with Client VPN 10.10.10.11 as it should. But I can't ping or access network resources in the local network for AnyConnected customer's PC that connected through the VPN.

  Here is the config Cisco ASA:

   : Saved : : Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz : ASA Version 9.2(2) ! hostname leela names ip local pool VPN-Pool 10.10.10.10-10.10.10.200 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 switchport access vlan 5 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp ! interface Vlan5 nameif dmz security-level 50 ip address 172.16.0.250 255.255.255.0 ! ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server 192.168.1.10 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network obj_any subnet 0.0.0.0 0.0.0.0 object network VPN-Pool subnet 10.10.10.0 255.255.255.0 description VPN-Pool object network NETWORK_OBJ_10.10.10.0_24 subnet 10.10.10.0 255.255.255.0 access-list inside_access_in extended permit ip any any access-list inside_access_in extended permit ip object VPN-Pool any access-list dmz_access_in extended permit ip any any access-list global_access extended permit ip any any access-list outside_access_in extended permit ip any any pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected nat (inside,dmz) source static any any destination static NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.10.0_24 no-proxy-arp route-lookup inactive access-group inside_access_in in interface inside access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz access-group global_access global route dmz 0.0.0.0 0.0.0.0 172.16.0.254 1 route inside 0.0.0.0 0.0.0.0 192.168.1.254 tunneled timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy server-type microsoft user-identity default-domain LOCAL aaa authentication enable console LDAP_SRV_GRP LOCAL aaa authentication http console LDAP_SRV_GRP LOCAL aaa authentication ssh console LDAP_SRV_GRP LOCAL aaa authentication serial console LOCAL http server enable 444 http 192.168.1.0 255.255.255.0 inside snmp-server location Vienna crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto map dmz_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map dmz_map interface dmz crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=leela proxy-ldc-issuer crl configure crypto ca trustpoint ASDM_TrustPoint1 enrollment terminal crl configure crypto ca trustpool policy crypto ca certificate chain ASDM_TrustPoint0 quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable dmz client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 no ssh stricthostkeycheck ssh 192.168.1.0 255.255.255.0 inside ssh timeout 30 ssh key-exchange group dh-group1-sha1 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.254-192.168.1.254 inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept dynamic-filter updater-client enable dynamic-filter use-database ntp server 192.168.1.10 source inside ssl trust-point ASDM_TrustPoint0 dmz ssl trust-point ASDM_TrustPoint0 inside webvpn enable dmz no anyconnect-essentials anyconnect image disk0:/anyconnect-macosx-i386-3.1.05170-k9.pkg 1 anyconnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 2 anyconnect image disk0:/anyconnect-linux-3.1.05170-k9.pkg 3 anyconnect image disk0:/anyconnect-linux-64-3.1.05170-k9.pkg 4 anyconnect profiles AnyConnect_client_profile disk0:/AnyConnect_client_profile.xml anyconnect enable tunnel-group-list enable group-policy DfltGrpPolicy attributes default-domain value group-policy GroupPolicy_AnyConnect internal group-policy GroupPolicy_AnyConnect attributes wins-server none dns-server value 192.168.1.10 vpn-tunnel-protocol ikev2 ssl-client webvpn anyconnect profiles value AnyConnect_client_profile type user group-policy portal internal group-policy portal attributes vpn-tunnel-protocol ssl-clientless webvpn url-list none username tunnel-group AnyConnect type remote-access tunnel-group AnyConnect general-attributes address-pool VPN-Pool authentication-server-group LDAP_SRV_GRP default-group-policy GroupPolicy_AnyConnect tunnel-group AnyConnect webvpn-attributes group-alias AnyConnect enable tunnel-group Portal type remote-access tunnel-group Portal general-attributes authentication-server-group LDAP_SRV_GRP default-group-policy portal tunnel-group Portal webvpn-attributes group-alias portal enable! ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 ! prompt hostname context no call-home reporting anonymous hpm topN enable : end no asdm history enable

  Can someone please help me solve this problem?

  When I tried to solve this I didn't choose which interface the Packet Tracer?

  The interface inside or DMZ interface?  Inside, he says it will not work with the dmz but the error did not help me

  Anyone here knows why it does not work?

  screen_shot_2014-08 - 12_at_16.34.57.png

  

  screen_shot_2014-08 - 12_at_16.33.06.png

  

  Hello

  Inside LAN is directly connected to the right firewall VPN... then I don't think you have to have the itinerary tunnele... can you try to remove the road tunnel mode and check.

  entrance to the road that is static to achieve 10.10.10.11 as its display is correct...

  Route by tunnel watch also with 255 administrative distance.  I've never used that in my scenarios... lets see...

  Concerning

  Knockaert

• Cisco VPN Client 2801 router

  Hello

  I installed a router cisco 2801 to accept vpn connections, I use the cisco vpn client and the tunnel is created and is being created of the its.

  However, I cannot ping my vlan (only those who have a nat inside the ACL, those who have not said I can ping), so I have a NAT problem, just don't know where.

  Heres part of my setup on the ACL,

  IP local pool ippool 192.168.100.10 192.168.100.100

  by default-gateway IP X.X.X.X (ISP GATEWAY)

  IP forward-Protocol ND

  IP http server

  no ip http secure server

  IP http flash path:

  !

  !

  IP nat inside source list 1 interface FastEthernet0/1 overload

  IP nat inside source list 2 interface FastEthernet0/1 overload

  IP nat inside source list 3 interface FastEthernet0/1 overload

  IP nat inside source list 6 interface FastEthernet0/1 overload

  overload of IP nat inside source list 20 interface FastEthernet0/1

  IP nat inside source map route SHEEP interface FastEthernet0/1 overload

  IP route 0.0.0.0 0.0.0.0 X.X.X.X (external IP)

  Route IP 192.168.10.0 255.255.255.0 192.168.90.2

  IP route 192.168.20.0 255.255.255.0 192.168.90.2

  IP route 192.168.30.0 255.255.255.0 192.168.90.2

  IP route 192.168.40.0 255.255.255.0 192.168.90.2

  IP route 192.168.50.0 255.255.255.0 192.168.90.2

  IP route 192.168.60.0 255.255.255.0 192.168.90.2

  IP route 192.168.200.0 255.255.255.0 192.168.90.2

  !

  NAT extended IP access list

  deny ip 192.168.10.0 0.0.0.255 192.168.100.0 0.0.0.255

  deny ip 192.168.20.0 0.0.0.255 192.168.100.0 0.0.0.255

  deny ip 192.168.30.0 0.0.0.255 192.168.100.0 0.0.0.255

  deny ip 192.168.60.0 0.0.0.255 192.168.100.0 0.0.0.255

  deny ip 192.168.90.0 0.0.0.255 192.168.100.0 0.0.0.255

  permit ip 192.168.10.0 0.0.0.255 any

  ip licensing 192.168.20.0 0.0.0.255 any

  IP 192.168.30.0 allow 0.0.0.255 any

  IP 192.168.60.0 allow 0.0.0.255 any

  IP 192.168.90.0 allow 0.0.0.255 any

  !

  access-list 1 permit 192.168.90.0 0.0.0.255

  access-list 2 allow to 192.168.10.0 0.0.0.255

  access-list 3 allow 192.168.30.0 0.0.0.255

  access-list 6 permit 192.168.60.0 0.0.0.255

  access-list 20 allow 192.168.200.0 0.0.0.255

  !

  SHEEP allowed 10 route map

  corresponds to the IP NAT

  !

  The 192.168.90.2 address is my switch L3 (Cisco 3750)

  Any pointer is more than welcome,

  Concerning

  Miranda,

  Have you tried to remove the following lines:

  IP nat inside source list 1 interface FastEthernet0/1 overload

  IP nat inside source list 2 interface FastEthernet0/1 overload

  IP nat inside source list 3 interface FastEthernet0/1 overload

  IP nat inside source list 6 interface FastEthernet0/1 overload

  overload of IP nat inside source list 20 interface FastEthernet0/1

  And simply let this one:

  IP nat inside source map route SHEEP interface FastEthernet0/1 overload

  ?

  I have all the neceary allowed in the ACL of NAT, so you do not have individual lines for each network.

  Also, I noticed that your ACL 20 reads

  access-list 20 allow 192.168.200.0 0.0.0.255

  But your NAT ACL bed

  ip licensing 192.168.20.0 0.0.0.255 any

  I think you have a typo in there, you have a 200 on 20 and on the other.

  Check it out and let me know how it goes. Don't forget to clear the NAT table after deleting these lines:

  clear the ip nat trans *.

  I hope this helps!

  Raga

• Cisco vpn client is supported on the analogue ppp connection

  can someone pls tell me if we can use the client vpn cisco on a ppp connection analog and put a pix that is not PPPs running. If it works, then why do we need to VPN L2tp/ipsec. can someone pls tell me something abt it. It is very urgent.

  concerning

  Assane

  Assane,

  If I understand your question, you speak with PPP initially to get an IP address from your service provider, then use the Client VPN VPN in your Pix Firewall. If so, yes it is possible.

  To name a few reasons why PPTP or L2TP/IPSEC is used instead of Cisco VPN Client are:

  1. because companies have used a PPTP or L2TP/IPSEC solution for some time and are migrating to Cisco VPN

  2. do not install vpn on the PC client software

  3. won't pay for the VPN Client software licenses

  Let me know if it helps.

  Kind regards

  Arul

• Unable to connect via the Cisco VPN Client

  Hello

  I have configured remote access VPN to ASA and tries to connect via the Cisco VPN Client 5.0

  I am not able to connect and watch the journal on the SAA

  ASA-3-713902: Group = xxxxx, IP = x.x.x.x, withdrawal homologous peer table is placed, no match!

  ASA-4-713903: Group = xxxxx, IP x.x.x.x, error: impossible to rmeove PeerTblEntry

  ASA does not support the K9 i.e. VPN - DES is enabled and VPN-3DES-AES is disabled.

  What could be the reason.

  Concerning

  Hi, I had this same problem, here is the solution:

  When you perform a debug crypto isakmp 255, so you see that the cisco vpn client does not support SHA +, you must use MD5 + AN or sha with 3DES/AES.

  Be careful, this debugging is very talkative, but that's the only way I found to get ITS proposal on debugging.

  Well, change your strategy using MD5 isakmp / OF would do the trick.