Variable user with building block

Similar Questions

• All of a sudden, the emails I am dial are a building block in the middle of the screen.  I can't minimize or move the drive to refer to another email.  Must send to the project folder.  Boring!  Why is this happening?

  Hello!  All of a sudden, the emails I am dial are a building block in the middle of the screen.  I can't minimize or move them if I need to take a break to refer to another email.  I send email partially completed to the drafts folder.  It is extremely annoying.  How to do this?  Operating system is OS X Yosemite (10.10.5) on a MacBook Pro.   Thank you!

  You are using the full screen? Try the command - command - F.

  Try a reboot.

  Make a backup using Time Machine or a cloning program, to ensure that data files can be recovered. Two backups are better than one.

  Try to set up another admin user account to see if the same problem persists. If back to my Mac is enabled in system preferences, the guest account will not work. The intention is to see if it is specific to an account or a system wide problem. This account can be deleted later.

  Isolate a problem by using a different user account

  If the problem is still there, try to start safe mode using your usual account.  Disconnect all devices except those necessary for the test. Shut down the computer and then put it up after a 10 second wait. Immediately after hearing the startup chime, hold down the SHIFT key and continue to hold it until the gray Apple icon and a progress bar appear. Startup is considerably slower than normal. This will reset some caches, forces a check for directory and disables all start-up and connection, among other things. When you restart normally, the initial restart may be slower than normal. If the system is operating normally, there may be 3rd party applications that pose a problem. Try to delete/disable the third-party applications after a reboot using the UN-Installer. For each disable/remove, you need to restart if you do them all at once.

  Safe mode - subject

  Safe mode - Yosemite

• How to remove a user with & in the username

  Hi all

  3rd party supplier system application deployed some user accounts with & in it.

  Can I know how to delete a user with & in the username?

  ex.  ABC and xyz

  I tried with singlequote '

  and doublequotes.

  Drop user 'abc and xyz '.

  always welcome

  Enter the value for xyz:

  It is treat & xyz as separate input variable.

  I don't have a OEM license to use it.

  Thank you

  Riou

  together set off the coast.

• Create the user with privileges only data entry.

  Hello guys,.

  A very basic question. I created the request of APEX, well obviously the user with whom I created this application has developer access, now I want to create a user who is able to see the developed application, I tried to find the user options, but could not.  Someone can help me to find the option, I need to follow, so that the newly created user is only able to enter data into forms and run reports and should not be able to make changes in the application developed.

  Concerning

  Faisal Niazi says:

  A very basic question. I created the request of APEX, well obviously the user with whom I created this application has developer access, now I want to create a user who is able to see the developed application, I tried to find the user options, but could not.  Someone can help me to find the option, I need to follow, so that the newly created user is only able to enter data into forms and run reports and should not be able to make changes in the application developed.

  Create 'end users' by selecting No for the user is an administrator of the workspace and the user is a developer account privilege options create new user accounts. These users connect to the APEX Application Builder. It can be given direct access to a request by specifying the ID of the application or alias to the URL:

  apex.oracle.com/pls/apex/f?p=

  or

  apex.oracle.com/pls/apex/f?p=

  Using an alias for the application is recommended.

  To restrict user access to pages, components and specific applications, create authorisation schemes and the apply to the application level.

• OIM 11 g - automatically configure a user with AD

  Hello world
  
  I'm a newbie with IOM and, I want to start available to users with my announcement directly after that we create on OIM. So I created a strategy to access the resource user AD with the correct ad server and the correct Organization and I affect it for all users. When I create a new user and I give some additional information such as address, phone number, e-mail, for example, this user is well configured on my ad, but the only information that are provided are his login, his first name, family name and none of the others.
  
  I don't understand why. I need to put in place an adapter for it? I also checked backup auto and Auto pre-filled in the process definition, but I don't know if it's the right thing to do.
  
  If you can help me with this. (I know it's a really 'newbie' question, but it will help me a lot to understand the basis of OIM features)
  
  Thank you very much!
  
  Thibault

  I don't think that Oracle has used any kind of Java Code for it. You can simply create logical task to achieve the same.

  Anyway connector AD comes with two jar files, and you can get the jars connector Pack itself or database.

  Through the design guide for Console for more details.

  And also for your use case steps:

  Go to the form Design
  Search UD_ADUSER
  Create new Version
  Save
  Go to prepopulate tab
  Click Add
  Select your attribute
  Adapter as ADCS complete first name, default, rule the command as integer value 7

  Save

  Make the user definition variable mapping > field name

• AutoNumber building blocks

  With the help of 9.0p230 FM, I see nothing in my AutoNumber building blocks scrolling list.  I've seen em before... did I have unintentionally disable them?  If so, how do I switch them back on?

  I've closed & reopened the application and even went to a new blank document.  No block construction.  What is happening with this?

  I'm sure that this has been fixed in 9.0p250, you should use. Really.

  Until then, you can get the valid building blocks in the back and enter them manually.

  -Michael

• Why is a user with the DBA privilege necessary side SQL Server to migrate?

  Greetings
  
  Project to migrate a SQL database to Oracle using SQL Developer.
  
  The docs say that a user with DBA privileges is required in the SQL Server database when you run the migration of the side Oracle.
  
  Why?
  
  Why a user with only READ access to SQL Server data would be necessary?
  
  Thank you very much!!
  
  -gary

  The DBA privilege at the source database is required because SQL Dev Migration is also collect information from SQL Server system tables, which a normal user is not always possible to query. It is mandatory that the migration is trying to build an Oracle schema which corresponds as much as possible the source database.
  But this requires having become DBA in the foreign database to avoid permission problems. If you SQL Server admin does not want the DBA privilege, you can also do a Migration offline - here the ADMINISTRATOR must run the generated scripts offline in-> Migration-> 3rd capture in the database offline party

• 5.1.7 server on El Capitan: create a user with a personalized folder location

  I've recently upgraded to El Capitan on my server once an apple advisor told me that 5.1.7 server had a bunch of bug fixes for Open Directory(which I plan on using down the road). Given that the Working Group Manager is not compatible with 10.11...

  Is there a way to create a user with a personalized folder location? When I create a user on the server, I can choose to create a home folder, with or without limitation in the disc or make the service of the user only. My problem is that I have no way (that I know) in the window of creating user to change the location of this folder.

  I tried to create a model of a user with a basic 'tailor-made' folder location (Volume/promised Pegasus/Home 2016 / etc...) but when I create the user, the home folder is not in the specified path.

  The "work around" I found for this batch of user is to create in the default location then move them on my raid Promise Pegasus, change the path to the advanced option to the each user and reassign the appropriate permissions.

  It is not so much a problem if I would deal with users 10. But I have to manage/create about 130-150 users every 5-6 months.

  I guess that there is an easier way to create a user with a custom home folder location. It would make sense that apple removes the Workgroup Manager and does not replace its characteristics.

  Best case scenario is that I do evil and do not hesitate to let me know if this is the case!

  Thank you

  Francis

  I may be wrong, but it seems that Workgroup Manager version 10.8 works under El Capitan: I can certainly start the application and query users / groups that are there.  I guess maybe it's on the machine as a rest to be updated periodically since days Lion... but it also shows that if you can find a copy, you may be able to run on your machine.

  HTH

• Yosemite: Why 'Shares and Permissions' displays 2 all users with different privileges?

  Some folders and files inside my user folder sharing and permissions like this:

  

  I can remove the user from "search...". "(a user who has been deleted and no longer exists) but I don't know what to do on both"all"users with different permissions. I can't delete the one with custom privileges. Help!

  Solved by Leroy Douglas. See What are these custom privileges?

• Functions defined by the user with several parameters

  I set features three following user using "Define."

  UF1 takes a single patameter;

  UF2 takes two parameters;

  and UFX takes two parameters - with the second is 'X' in the definition.

  

  Œuvres F1.  F2 is the EVAL of F1 version and it works too.  User functions only seem to work fine.

  F3, a function of two user settings, produces a graph of NaN.

  F4 is the EVAL of F3 version.  Note that 'B 'is not replaced by 1'.  Also produces a NaN chart.

  F5 produces a graph of NaN.

  F6 is EVAL of F5.  The 'X' is not replaced (even with the ' B' above), and even if it looks like 'X * X', it also produces a graph of NaN.

  

  Is it possible to get defined by the user, with several parameters, features work by tracing the curve?

  Hi!, Fortin:

  If you download and install the ultimate Firmware with the version of the software: 2015 6 17 (8151), with the number of Version: 1.1.2 - 11, you can trace your examples of definition of the function, with curves and values, without NaN.

• buy an iphone 5s by amazon and I came with iCloud blocked an account... {I called the seller and does not that I do that I'm from Venezuela please need your help}

  buy an iphone 5s by amazon and I came with iCloud blocked an account... I called the seller and does not that I do that I'm from Venezuela please need your help

  No one here can help you. The device is locked activation. Since you have made the purchase by Amazon, you can check with them to see if they will stand behind it. No one on the forum, or Apple can help you remove the lock. Only the previous owner can do this. I suggest that you demand a refund, so let's start a claim with Amazon about this dealer.

• LabVIEW interface with multiple blocks of Festo module

  I am trying to connect with a block of Festo, but I can't. Here are the details:

  I'm under Labview 2012 SP1 with IndComm-DeviceNet 2.2 pilot on a 64-bit Windows OS. I installed a PCI 8532 card NOR. I see the map to the MAX.

  The block of Festo is built with the following Modules: CPX_FB11 (communications module), 4 analog input Modules, 1 Digital module, 2 digital modules followed by 32 Festo valves. (Image below)

  

  Using DeviceNet PXIPCI Basics.lvproj I did the following:

  In the project, right-click on desktop > New > targets and devices > existing target or device, discover an existing target or device...

  Expand the node of DeviceNet Master Interface, DeviceNet1 chosen and added to the project.

  A click on the newly added DeviceNet/device target > New > targets and devices...

  Expanded the Festo Block "CPX_FB11" selected DeviceNet slave device and added to the project.

  Initially, I received an error card technique 'EDS file no assigned' I solved this by following the direction listed here.

  However, I'm unable to "see" anything other than the CPX_FB11 LabView. The tree view of the devices lists not analog, Digital e / s or valves. I can't operate the Valves and IOs digital or analog. When I run the entire project VI they then expire.

  Any help would be appreciated.

  Thank you

  Tennessee Paul

  Hi Jesse,.

  I'm not entirely sure what the specific problem was. I kept getting strange behavior. Errors in LabView and on my camera from Festo. The EDS files change. So, I did as any natural born THERE would be worker, I rebooted.

  Here are the steps I used to get this project going. In doing so, I found that to set up a DeviceNet device in LV2012SP1, no need to manually enter the data in file EDS. There is a tool to load files EDS. It dealt with issues I had in the previous Forum posts: here about loading files EDS in LabView and here regarding setting up a DeviceNet network.

  Environment: Windows 7, 64-bit processor. IndComm 2.2 pilot. LabVIEW 2012 SP1

  Starting with the example LabView project: "Devicenet PXIPCI Basic.lvproj.

  Add a DeviceNet master to a LabView project

  1. The project: right-click on my computer
  
  
  1. Select new
  
  
  2. Select the targets and the device (s)
  
  
  2. Select the option "discover existing devices.
  
  
  3. Select the discovered device.
  
  
  4. Click 'OK' (Note: in this case, my master is a card PCI of NOR-8532)

  Add a DeviceNet slave device to a LabView project

  1. Right-click on the master device newly added in the project tree
  
  
  1. Select new
  
  
  2. Select the targets and the device (s)
  
  
  2. Select 'discover existing devices.
  
  
  3. Select the discovered device.
  
  
  4. Click OK. (Note: in this case my slave is a block of Festo CPX-FB11.)

  Load an EDS file to the slave device

  1. Right-click on the slave device
  
  
  2. Select "Sheet"... »
  
  
  3. Click on add files...
  
  
  4. Navigate to the location of the EDS file.
  
  
  5. Select the file.
  
  
  6. Click OK.
  
  
  7. In the left pane, expand the data sheet newly added up to reach the node displays the version.
  
  
  8. Select the version.
  
  
  9. Click OK.

  Check the device and file EDS

  1. Right-click on the slave device
  
  
  1. Select utilities
  
  
  2. Select the Panel of Test online
  
  
• Select the option 'Device status' in the field of category on the left.


• On the right, select the slave device, you want to check.


• Click on "check the device".


• Read the errors/warnings or lack thereof.

In my case I had errors in my EDS file. Basically the slave device was not defined for the correct number of bytes of input/output in the EDS, i.e. a wrong configuration file. To fix this I had to change the EDS file.

Edit the file EDS

To change the EDS file, I used EZ-EDS , which is a freeware, devicenet specific EDS editor of ODVA.

I did my corrections and saved my file EDS. (After having saved my original, of course).

Remove the installed Labview EDS file

1. Navigate to the following location: C:\ProgramData\National Instruments\NI-IndComm for DeviceNet\Datasheet


2. Remove the sheet (Note: there is more that one datasheet added manually.) Additional EDS files come with the IndComm driver. Find the EDS file for the specific device that you want to replace and delete).

I restarted LabView.

I went through the steps above again and loaded my new EDS file.

I saved the project and came out of LabView.

I rebooted the computer and the slave device.

I restarted the project and launched a VI.

I was able to communicate with the device. That is something that I had not been able to do before. And, in doing so, I discovered how the device speak and why were not each module. (I have a standard for my block devices EDS file, as it appears that LabVIEW is not capable of a modular system that requires an EDS file for each module. I could be wrong on that last part though, as there may be a setting on my real device. But it is unecssary in my project. So I do not consider this further.) Because I was using a standard file of the EDS, only a single slave device showed, and so the data for each module are in the stream of bytes returned to the DeviceNet network. Addressing each module is a question of analysis the bits and the bytes appropriate.

Thank you

Tennessee Paul

• problem with a block of memory in labview 2009

  Hi all

  I have "ERROR: MapLib:979 - LUT4 symbol" during the compilation process (lots of errors like this), and I discovered that the reason of my problem is block of MEMORY.

  To be sure that the problem is in this block, I did a very simple project in LabView 2009 (on FPGA Target PCI5640R) only with the use of this block you can see in the photo, as well as in file test_memory block.lvproj attached link: https://www.dropbox.com/sh/u87f1oihelmm4dq/Jo_6-bICSf

  

  I have a problem with compiling VI with this block, and I have so many errors like:

  ERROR: MapLib:979 - LUT4 symbol
  "window/Thatcher/n_00000036/nSCTL_00000013_00000014/n_000000A3/cOutLoc<0>1.
  (output = window/Thatcher/res000001ed_wi<2>) is the input signal
  "window/Thatcher/res0000020d_wo<1>" that will be deleted. See Section 5 of the
  Map a report file to find out why the input signal will become conveyors.

  or

  ERROR: MapLib:978 - LUT4 symbol
  "window/Thatcher/n_00000036/nSCTL_00000013_00000014/n_000000A3/cOutLoc<23>1.
  (output = window/Thatcher/res000001ed_wi<25>) is an equation that uses
  input pin I2, which no longer has a connected signal. Make sure that all the
  the pins used in the equation for this LUT are signals that are not cut
  (see Section 5 of the report file map for details on which signals were
  adjusted).

  Entire report, you can see in the file report.txt on the attached link.

  I would appreciate if someone could take a look at my problem with simple project and suggest me a solution.

  I'm really stuck with my biggest project which need to have this memory block.

  I'm looking forward to hear from you,

  King looks

  ING. Damir Hamidovic

  Hi all

  I find a sollution to my problem.

  In memory-properties-general-setting up, I changed the block to look up Table memory, and I compile memory.vi and run it successfully.

  I did change as you can see on the picture:

  

  Just, can you tell me is it all "bad properties" and limits the use of this type of memory (Look up Table) of the implementation?

  King looks

• You need permission to perform this action - field user with file rights. Please advice

  You need permission to perform this action - field user with file rights.

  I can't access folder on drive network even with domain administrator of error do 'you need permission to perform this action. "
  I would be very grateful if you could please advice, I can't change folder\files in this folder, even with admin rights.
  Thanks in advance
  Saad Ali

  Hello

  I suggest you post the same question in the Microsoft Technet forum for assistance. We have a team to help you with this guy's questions.

  http://social.technet.Microsoft.com/forums/en-us/categories/

• How to connect 2 PC with CPL blocks on windows?

  How to connect 2 PC with CPL blocks on windows?

  original title: CPL problem
  Hello
  Please select your language from the drop-down menu above to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find your language above, support for additional international sites options are by following the link below:
  http://support.Microsoft.com/common/international.aspx