Vblock or not VBlock

Similar Questions

• Vblock 0

  I was going through the architecture of the Vblock0 and saw a network diagram where the storage (EMC Celera) is connected to the nexus 5 k instead of connect directly from the fabric of 6100 of interconnections.

  Is there a particular reason to do so and how storage traffic flows to the N5K I thought we cannot have multi hop with FCoe

  any ideas?

  Ambi

  Ambi

  UCS currently does not support the targets directly connected FC or FCoE.

  All UCS storage traffic goes on the CF uplinks and not 10 gig ports that are capable of FCoE.

  This will change in the near future (next version of the software of the UCS).

  So, for now, yes the link between UCS for the 5 k in architecture Vblock is CF. The 5 k could connect to a table FC or FCoE.

  Thank you

  -Matt

• VCE vblock, LSI_SCSI: Reset for device \Device\RaidPort0 ERROR in VM Windows Event logs

  Hello, I have been a problem for some time and I can't seem to understand this issue. Basically, the VM freezes but returns after 30 seconds.
  I found the problem was present on all data warehouses and even showed errors for for guests (san boot) boot sector. After changing the round robin at the fixed path on data warehouses to use a specific fiber channel switch LSI_SCSI errors were gone on all data warehouses, VM ect... everything worked normally.
  We have an installation program VCE vblock with UCS (blades), Nexus 5ks and VNX.

  So basically, we were troubleshooting paths FiberChannel beside the UCS to the VNX. We have changed ports on the VNX SP but side A was always bad / good B... Compared the configs of nexus for the two, identical configs/features beside the specificities as VSAN ect. Examined the configs for the UCS, but are fundamentally the same with Setup on the side B, but everything looked good. Nothing is defective.
  I noticed Tx errors on ports of module e/s and CRC errors on ports in the Nexus. Thought it might be a bad fiber so I replaced... The problem is always present. Any ideas? Thanks in advance!

  Data Center:
  UCS: 5108 Chassis, IO module 2104XP (2.2 (3g)), blades B200 M2, fabric 6120XP interconnections (5.2 (3) N2 (2.23 g))

  5.5 ESXi update 2

  2 nexus 5ks

  VNX 5500

  I found the culprit, SFP. The FPS that were used throughout the entire upward was incompatible and FUBAR would. Not match speeds, single mode when it should have been multi ect. Just all around the nightmare. It's on EVERYTHING from the VNX to IOM simply ridiculous. After completing the gutting of the SFP and the fiber, replacement and then delivered at the point of the chassis of the UCS everything was great. Honestly, I don't know how it worked at all with this configuration. Anyway, if you want something done you have to do it yourself.

• Backup VM with VBLOCK

  I'm new to vBlock but have a decent understanding of vSphere and pretty much thru ver4.1 (some in ver 5).  Here's my question:

  I'm with a company that uses vBlock and ESXi4 stand-alone servers.  No vCenter.   Inrteresting Setup.    They are not instant, and they do not have the VM backups.

  Now, I'm still green behind the ears to this company, so I don't think I can say much of their virtual infrastructure and virtual policies, but whenever they need to make changes to their system (even if they are virtual machines), they either do or build a new server and test it on the new server.   In regards to the side of the virtual machine, they told me that they are not instant is because their SAN (Fibre Channel of EMC) vBlock can VM backups.  That's why even serves as to why they have no VM used cover backup/restore applications.   Fortunately, they have never had a need to post this because they have never had to restore a virtual machine.

  I am skeptical.   From what I've read, vBlock and SAN interface device provides true VM backups.   If I'm not mistaken VBlock simply integrates 3 (vSphere, Cisco and EMC SAN routing).   I don't know that the SAN has the standard ability to backup files (IE.  The virtual computer files) but to be able to completely restore a computer virtual... I don't think so.  And, although it is possible to recreate a virtual machine files... it will take time to do so and if the configuration remains intact or not is questionable, in my opinion.   In any case, I wanted to see if someone knew more VBLOCK and could you tell me if what I said is true.    If this isn't the case, I'll have to chime so that they can take the appropriate decisions.

  A Vblock (Yes, that's how VCE spells it) is sold with Enterprise more than license for the hosts, they are required to be able to include Nexus 1000v and PowerPath VE, with vCenter Standard edition (which allows unlimited guests).

  By the reference guide (page 9) architecture - https://community.emc.com/servlet/JiveServlet/previewBody/5665-102-2-20157/h6935-vblock-infra-packages-ref-arc.pdf

• IBM Notes 9 does not start after the update to Acrobat DC

  Hey people,

  in January 2016 we went from Lotus Notes 8.5.3 and Acrobat 9.5.5 to IBM Notes 9 and Acrobat DC. After the first installation, everything works fine.

  After update to Acrobat DC it always adds the following line to the notes.ini file:

  EXTMGR_ADDINS = AdobePDFMToolbarInst

  This causes IBM Notes to crash at startup. The following lines are written to the log file:

  [0c 58:0006 - 17BC] 11.05.2016 16:46:35, 75 terminate > of entered NNOTESWC

  [0c 58:0006 - 17BC] 11.05.2016 16:46:35, 75 Terminate > queue name decided to: MQWCTTHREAD6076_2562

  [0c 58:0006 - 17BC] 11.05.2016 16:46:35, 75 Terminate > sending notes, iRefCount WKSMSG_NOTESWC_CLOSE_NOTES: 0

  [14B 0:0002-14 to 8] 11.05.2016 16:46:35, 75 ProcessWksMsgExt > Message: receipt of WKSMSG_NOTESWC_CLOSE_NOTES

  [14B 0:0002-14 to 8] 11.05.2016 16:46:35, 75 Handle_CLOSE_NOTES > entry

  [14B 0:0002-14 to 8] 11.05.2016 16:46:35, 75 Handle_CLOSE_NOTES > NBP does not

  [14B 0:0002-14 to 8] 11.05.2016 16:46:35, 78 Handle_CLOSE_NOTES > message sending close to all child windows

  [14B 0:0002-14 to 8] 11.05.2016 16:46:35, 80 Handle_CLOSE_NOTES > message sending close to the main window

  [14B 0:0002-14 to 8] 11.05.2016 16:46:35, 81 Handle_CLOSE_NOTES > customer alert that it needs to wait for us to go down completely

  [14B 0:0002-14 to 8] 11.05.2016 16:46:35, 81 Handle_CLOSE_NOTES > stop complete, descending

  [6824:0002 - 08BC] 11.05.2016 16:47:50, 66 NEMCheckPreviousInstance > can't wait to treat [5296] as open process failed: error = 87! Continue the launch.

  [6824:0002 - 08BC] 11.05.2016 16:47:50, NEMCheckPreviousInstance 66 > treat [5296] out, continue to launch

  [6824:0002 - 08BC] 11.05.2016 16:47:51 Agent "PDFMLN_8_UNINST" - Fehler: error to the method of the product object / / PDFMLN_ * _UNINST:14

  [6824:0002 - 08BC] 11.05.2016 16:47:52 Agent "PDFMLN_8_UNINST" - Fehler: error to the method of the product object / / PDFMLN_ * _UNINST:14

  [6824:0002 - 08BC] 11.05.2016 16:47:52 Agent "PDFMLN_8_UNINST" - Fehler: error to the method of the product object / / PDFMLN_ * _UNINST:14

  [6824:0002 - 08BC] 11.05.2016 16:47:53 Agent "PDFMLN_8_UNINST" - Fehler: error to the method of the product object / / PDFMLN_ * _UNINST:14

  [6824:0002 - 08BC] Thread = [6824:0002 - 08BC]

  [6824:0002 - 08BC] stack base = 0x002E6A74, the stack size = 39648 bytes

  [6824:0002 - 08BC] PANIC: OSVBlockAddr: Bad VBlock handle (0\0)

  Manual removal of line «EXTMGR»... ' solved the problem. Unfortunately, I have to do once again, after Acrobat updates each time. Of course, this corresponds to each PC in our society.

  Please tell me if there is a solution to this problem. Maybe it's possible to prevent adding one line to the notes.ini Acrobat file?

  To make sure that: of course I also placed this question at IBM!

  Kind regards

  Florian Burger

  Just to close this band of working capital, IBM Notes 9 FixPack 6 solves the problem.

• Apple Watch activity is not in the cloud?

  So, I've been using a Apple Watch for a while and my number one problem is that 'Activity', I put together for the last year is not sync with the iCloud, so when I upgraded my iPhone 6 to iOS10 all my activity watch is gone. I tested this point last week and it seems that "Activity" app does not synchronize your data in the cloud, so if you lose your phone or your watch you will have to start all over again and latest data are lost. This seems to be a huge concern when I spend all this time my overall follow-up and progress. Everyone see what happens if you put to level or restart/reset your watch or your phone?

  Hello

  Health and historical activity data is stored on your iPhone. It is not recorded separately in iCloud.

  To guard against data loss, be sure to make regular backups of your iPhone.

  If the backup via iTunes, make sure to select the option to encrypt iPhone backup (unencrypted backup excludes the sensitive data, including health and activity). iCloud backups are encrypted as standard.

  More information:

  The backup of your iPhone, iPad and iPod touch - Apple Support

• iTunes will not regroup under the name of artist albums

  I noticed at the bar on the left with the artists, sometimes there are twice, the same artist, with each having only some of the albums and I can't group all albums under the name of an artist to the bar.for some artists can't do, but I did it because some others.anyone know what to do?

  If you see unexpected songs groups when you browse an album - https://support.apple.com/HT204538 - 'songs from the same album may not be grouped as expected when you view them in display Albums in iTunes."

  For most people this solution seems to be one that works: August 2008 post by turingtest2 temporarily change labels - https://discussions.apple.com/message/7904806#7904806 or http://www.samsoft.org.uk/iTunes/merge.asp - add a letter at the end of the name of the artist, close the read information, then open it again and remove the letter. This works often but I had cases where securities combined when a letter has been added but divorced when he was kidnapped again.

  The following sections provide additional solutions:

  Often a solution: select all the tracks on the album, file > info (or right-click > news > Details) and give them all a single "album artist", or check the indicator of "compilation" (as in https://discussions.apple.com/message/17670085#17670085).

  Steve MacGuire alias turingtest2 - iTunes and iPod tips and tricks - grouping beaches in Albums - http://www.samsoft.org.uk/iTunes/grouping.asp (old post on Apple Discussions http://discussions.apple.com/message/9910895#9910895)

  If they are several CD sets, you will also need to enter the appropriate information in the fields of number of disk.  If they are not a set of multiple CDs that you must always make sure any vacuum or disc number fields are properly defined.

  Another explanation of hhgttg27 August 2015 - https://discussions.apple.com/message/27784417#27784417

  If they are mp3 files are trying to change the version of the ID3 tag, which can cause iTunes to re - write the tags and clarify inconsistencies.  I use iTunes 7.5 (Yes, from 2007) so I can't tell you where it is in later versions.

  I had a case of grouping stubborn reality.  The tracks will be re-group in a way that has no meaning when I changed metadata.  Without going into details, I deleted tracks iTunes completely, then add the files and they are all grouped together correctly.

• Why my notes sync between my Mac and iPhone?

  I have my MacBook Pro with Mac OS X 10.9.5 Mavericks and my iPhone is running iOS 10.0.1 and used to synchronize my notes! Is it because of the huge gap in operating systems? I SHOULD update my Mac to Mac OS 10.10 + for this problem? Thank you!

  In order to synchronize Notes between your Mac and iPhone, you must configure iCloud > http://www.apple.com/icloud/setup/

  But this requires macOS Sierra 10.12, the latest available version and the last iOS available for your iPhone.

• iPhone 7 more buttons outside does not

  I've had my iPhone 7 + for about 2 weeks now. Every once in awhile all buttons outside to stop, volume up/down, power, home. The home button will still record and push and give the sensation of taptic and touchID works. The phone itself still works and I can answer texts and which do not use notifications.

  The couple spent time he did, he came upon her in about 4-5 minutes, however it was about half an hour and still nothing. I want to restart my phone, but the switch does not work.

  Has anyone seen this issue or know how to fix?

  Thanks in advance.

  I just experienced the same problem on my iPhone 7, I think it's a bug in iOS, but I am using iOS 10.0.2. Power + button low Volume allowed me to turn it off then turn it back on... Apple please fix this bug!

• Why video does not work in safari

  The video on all Web sites IN safari has stopped working. No idea why?

  Do you get any error messages? If this is not the case, see if by double clicking the home button and drag to the top safari help. -AJ

• Reminders do not display or stick to the lock screen in iOS10

  IOS10 (10.0.1 and 10.0.2), on an iPhone (I use an iPhone 6), reminders are no longer reliable. I had several cases where the callback doesn't show even on the screen lock and many more times when the recall won't 'glue' to screen lock for more than a short period. Before iOS10, when you said to remind you at a certain time or place, the recall would display on the reliable lock screen until she has been marked as "completed".

  It is a major issue for people who depend on the application for the important tasks and calendar. There is a thread of any discussion on this point, for some reason, has been marked as "solved" even if a large number of people continues to post telling him that there is a problem for them too (as the thread located here). I wanted to start this new discussion which we hope will remain open until it is effectively resolved.

  Thank you!!! This is a HUGE problem!

  Since the update I had to reboot my phone EVERY day.

  Is the stick of reminders... or they do not. Lately they don't yet show upward. Then other things stick to the lock screen can't get rid of.

  Currently this feature on the phone is USELESS

• I need to change my security issues and said we do not have enough information to reset your

  I need to change my security but said Questions we have insufficient information to reset security of your apple ID questions.my is [email protected] I want to slove this problem please help me

  You should contact the account of Apple security team. To join, click here and choose a method; If this page does not list one for your country or if you are unable to call, complete and submit this form.

  (145174)

• iPod not recognized by iTunes?

  I have iTunes installed on a computer running Windows 10. iTunes is updated to the latest version since this morning.

  My iPod is a 7th generation Nano

  Here's what I've tried so far:

  • Update to iTunes (the problem began before the update and persisted thereafter)
  • Reset the iPod (by pressing the menu and sleep buttons, or whatever they are called, until the screen goes black and then displays the apple logo)
  • Reinstall iTunes
  • Removal/installation/update driver iPod (my iPod appears under portable devices and tells the pilot because it is the latest version, attempts to manually install the driver in the iTunes folder indicates which is the driver already installed). I tried this before and after reinstalling iTunes.

  However, I don't have an Apple Mobile Device driver. I couldn't find two solutions to do this, which has been updated the driver on the iPod, which did nothing. Another option involved to restart the Apple Mobile Device Service. Who also did nothing.

  I also read that reformat the iPod through disk management has worked as well, but my iPod does not appear as a disk. In fact, it is not at all. iTunes opens when it is connected and says it cannot recognize it, but it does not appear under devices and readers.

  On a strange note, I have an unknown USB device under USB controllers in device management. Out of curiosity, I unplugged my iPod, uninstalled and plugged my iPod back, time in which the unknown device is returned. So I guess it's my iPod (in the unrecognized State). You know not so relevant.

  I am at one loss as to what else to do. The iPod still works, I can still listen to all music that has been synchronized to him before, but that's all.

  This just started today. Every other time I connected the iPod, it was immediately recognized by iTunes and worked well. Seems that the problem is the absence of the Apple Mobile Device driver, if I was not able to fix this.

  I have not tried to plug the iPod on another computer yet. The only other computer I have is an old laptop that takes forever to initialize. I will try that, after work and see if my iPod works on that one.

  If you have already tried to reinstall iTunes and manually delete specific things like the drivers, you can completely remove iTunes and related software components

  Remove and reinstall iTunes and software for Windows 7 and later versions - Apple Support components

  Don't forget to uninstall the components all the listed in the described order.  Then, download and install the latest version of iTunes from here

  https://www.Apple.com/iTunes/

• I resized the Partition Mac to make more space for BootCamp and now Windows will not boot

  On a collague MacBook Air running 10.11.4, we used disk utility to reduce the Mac Partition so that we could then use a Windows tool to extend the BootCamp partition. However, upon restart, we got a BACK screen with the error that Windows cannot start because it cannot find the boot device.

  Help, please?

  This is not a mechanism supported by Apple to change the size of the Windows partition. Apple supports the remove/reinstall only.

  We try to remedy. Please after the release of the following OSX Terminal commands.

  diskutil list

  Cs diskutil list

  sudo TPG - vv - r see the/dev/disk0

  sudo fdisk/dev/disk0

  What is the model/year of the MBA? Please, do not post the serial number of your Mac. Orders 'sudo' will ask for your password.

• Why do I get a message saying that my computer is not registered for me

  I show the icon of the application that will not download because I get a message that says my computer it is not mine or is not saved for me.  WHY!

  What is the EXACT message you get?