VCA mode in settings of the cluster

Similar Questions

• Activation of VCA mode for cluster production

  Hello

  I have the following configuration:

  • Existing Cluster_A with ESX 3 hosts running on the processor Intel Xeon E5540 (Nahelem)
  • 30 VM runs in a production environment
  • 2 new ESX hosts running on the processor Intel Xeon E5649 (Westmere)

  2 new guests are not added in vCenter again, but the goal is to allow the addition of these 2 new hosts in Cluster_A.

  I understand that, in order to have all 5 hosts in the same cluster, EVC mode must be activated with the highest level being "Nahelem" (lowest common denominator).

  From a theoretical point of view, masking any CPU to apply will be identical to the current CPU presented the virtual running machines, settings allowing CVS using the same architecture CPU should not cause conflict or problem.

  Therefore, I would ask you confimation that activation VCA and Nahelem for Cluster_A upgrade will not cause downtime or impact (e.g. BSOD) to the virtual machines.

  Thank you

  Kenny

  Therefore, I would ask you confimation that activation VCA and Nahelem for Cluster_A upgrade will not cause downtime or impact (e.g. BSOD) to the virtual machines.
  Kenny

  Hello

  Is 100% safe operation (done many, many times the performance of clusters). No side effects :-)

  1. create a TEST VM
  2. Add the new server ESX to vCenter
  3. put in maintenace mode
  4. Add to the cluster
  5. allow to LCA
  6. exit maintenance ESX
  7. try to vMotion between the old and the new node in a cluster
  8. If vMotion won't work, says André, you should turn off the virtual machine and run it.
  See you soon
  Artur
  

  Please, do not forget the points of call of the "useful" or "correct" answers

• Problems with the VCA mode when moving to Vcentre 4.1

  Hi all

  I currently have three ESXi 4.0 update 3 host running in a cluster. Two servers are identical and the third a later generation of CPU. The cluster is running in mode VCA Intel i7 with success.

  Also, my server Vcentre is 4.0 update 3 running on a 32-bit Windows Server 2003 R2.

  I built a new server on Windows Server 2008 R2 Vcentre and I am running Vcentre 4.1 update 1.

  I did the exercise to my old server Vcentre guests to my new. No problem until I try and their cluster. My server with the latest CPU is not allowed admission to the cluster. The new cluster is running same EVC mode as the old cluster.

  Need to update 4.1 Vcentre 1 be backward compatible for EVC modes with respect to the material?

  The servers are all DELL R710, the old two servers running XEON X 5570 processors and the latest Intel XEON X 5670 processors host tracks

  Do I have to update all 3 hosts 4.1 before I can redefine the clusters in EVC mode?

  Hoping that someone has been through a similar experience and can advise you. Unfortunately, I do not have a test lab to run it on.

  See you soon. Mark

  I don' t think you need to upgrade to ESX host.

  I think try in the following order:

  (1) turn on VCA for cluster

  (2) add the latest processor, select baseline and then old processor server.

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=1003212

  -A

• Switch Cisco 2960/3560 = > recovery password and default settings with the button Mode

  Hi Experts,

  I have some confusion with the button Mode with cisco 2960/3560 switches.

  I read on many forums and articles, but where things are not clear.

  a place given 3 seconds and somewhere is given 7 or 10 seconds.

  Qus1), what is the exact time to press/hold Mode button to perform two following tasks:

  A. password recovery (according to my knowledge 3 sec) good or bad?

  Configuration of the switch (start + run) would be safe

  After the recovery of password? Yes or no

  B. factory default (according to my knowledge 10 dry) good or bad?

  I'm afraid, because if I press mode button more than 3 seconds, then

  It will delete any configuration of cisco switch. Yes or no

  Qus2) I want to recover the catalyst 2960/3560 switch password without

  Start/run configuration to lose. That is my main concern.

  Please tell me how to do this, what will be the time keeping Mode buttom

  in a few seconds?

  Qus3) which means this line

  "If the password recovery mechanism is disabled in switch

  then you will lose all the config.

  This sentence has been given on this forum url

  https://supportforums.Cisco.com/thread/140848

  KS

  Attach a terminal or PC with terminal emulation (for example, Hyper Terminal) port console switch.

  Use the following terminal settings:

  • Bits per second (baud): 9600

  • Data bits: 8

  • Parity: None

  • Stop bits: 1

  • Flow control: Xon/Xoff

  Note: For more information on the wiring and connection of a terminal to the console port, refer to connecting a Terminal to the Console Port of Catalyst switches.

  Unplug the power cable.

  The power switch and take it to the switch: command prompt:

  2900XL, 3500XL, 2940, 2950, 2960, 2970, 3550, 3560, and 3750 switches of the series, to do this:

  Press and hold the mode button located on the left side of the façade, while you reconnect the power cable from the switch.

  2960, 2970

  Release the Mode button when the SYSTEM LED flashes orange and then turns green. When you release the Mode button, the SYSTEM LED flashes green.

  3560, 3750

  Release the Mode button after about 15 seconds when the SYSTEM LED turns green. When you release the Mode button, the SYSTEM LED flashes green.

  The system was interrupted before the flash at the end file system initialization

  loading the operating system software:

  flash_init

  load_helper

  boot

  switch:

  Run the flash_init command.

  switch: flash_init Initializing Flash... flashfs[0]: 143 files, 4 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 3612672 flashfs[0]: Bytes used: 2729472 flashfs[0]: Bytes available: 883200 flashfs[0]: flashfs fsck took 86 seconds ....done Initializing Flash. Boot Sector Filesystem (bs:) installed, fsid: 3 Parameter Block Filesystem (pb:) installed, fsid: 4 switch: !--- This output is from a 2900XL switch. Output from !--- other switches will vary slightly.

  Run the load_helper command.

  switch: load_helper switch:

  Question the dir flash: command.

  Note: Be sure to type a colon ":" after the dir flash.

  Appears in the file system of the switch:

  switch: dir flash: Directory of flash:/ 2    -rwx  1803357                  c3500xl-c3h2s-mz.120-5.WC7.bin !--- This is the current version of software. 4    -rwx  1131                     config.text !--- This is the configuration file. 5    -rwx  109                      info 6    -rwx  389                      env_vars 7    drwx  640                      html 18   -rwx  109                      info.ver 403968 bytes available (3208704 bytes used) switch: !--- This output is from a 3500XL switch. Output from !--- other switches will vary slightly.

  Type rename flash: flash: config.old config.text to rename the configuration file.

  switch: rename flash:config.text flash:config.old switch: !--- The config.text file contains the password !--- definition.

  Issue the boot command to boot the system.

  switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC7.bin"...############################### ################################################################################ ###################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC7.bin" uncompressed and installed, entry po int: 0x3000 executing... !--- Output suppressed. !--- This output is from a 3500XL switch. Output from other switches !--- will vary slightly.

  Enter "n" at the prompt to abort the initial configuration dialog box.

  --- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Continue with configuration dialog? [yes/no]: n !--- Type "n" for no. Press RETURN to get started. !--- Press Return or Enter. Switch> !--- The Switch> prompt is displayed.

  At the switch prompt, type en to enter a mode.

  Switch>en Switch#

  Password recovery

  Type rename flash: config.old flash: config.text to rename the configuration file with its original name.

  Switch#rename flash:config.old flash:config.text Destination filename [config.text] !--- Press Return or Enter. Switch#

  Copy the configuration file in the memory.

  Switch#copy flash:config.text system:running-config Destination filename [running-config]? !--- Press Return or Enter. 1131 bytes copied in 0.760 secs Sw1#

  The configuration file is now reloaded.

  Replace the current passwords that you do not know. Choose a password with at least one capital letter, one number and one special character.

  Note: Replace passwords that are required. You must crush not all passwords listed.

  Sw1# conf t !--- To overwrite existing secret password Sw1(config)#enable secret !--- To overwrite existing enable password Sw1(config)#enable password !--- To overwrite existing vty password Sw1(config)#line vty 0 15 Sw1(config-line)#password Sw1(config-line)#login !--- To overwrite existing console password Sw1(config-line)#line con 0 Sw1(config-line)#password 

  Write the running configuration in the configuration file with the write memory command.

  Sw1#write memory Building configuration... [OK] Sw1#

  For factory reset:

  do not give under the control of factory reset

  Switch#copy flash:config.text system:running-config

  can I copy the running configuration to Flash

  Switch flash running-config #copy:

  Destination file name [running-config]?

  Building configuration...

  [OK]

  Switch #copy running-config startup-config

  Name of destination file [startup-config]?

  Building configuration...

  [OK]

  Review the link for more information below

  http://www.Cisco.com/en/us/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml

  Please note the useful messages.

  Concerning
  Vesta
  "Everybody is genius." But if you judge a fish by its ability to climb on a tree, he will live his entire life, believing that this is stupid. "

• Activate the VCA Mode of VMware vCenter Server Appliance

  Hello

  I'm pretty new on vSphere.  I have two hosts running esxi 5.1 what one of these hosts running the "VMware vCenter Server Appliance' with vSphere version 5.5.  I currently have a single cluster containing all the VMS as well hosts and the SAN.

  I try to activate the EVC mode, but when I try it tells me that the host is not allowed because there are powered on virtual machines.  I can turn off all the virtual machines except the vCenter device and I still get the problem on the host that has the device on it.  If I turn off the unit, I can't use vSphere to activate CVS.

  How can I activate CVS when vSphere does not work?

  Thank you

  Jeff

  Hi Welcome to the communities,

  This one is a bit complicated

  You have:

  1. turn off all VMs on Host1 (while vCenter device is on Host2)

  2 bring Host1 on Cluster, select CVS clustered.

  3. put all the virtual machines on Host2 (also vCenter device)

  4. connect on Host2 directly to vSphere Client Windows

  5. remove the vCenter inventory unit

  6. connect on Host1 directly to vSphere Client Windows

  7. the data store when the appliance and add it to the inventory of research. Power on

  8. connect the device with Web client or vSphere vCenter

  9. move the second host in the cluster

  And you're done

  Concerning

  Tim

• Can join a Cluster of storage disk out of Maintenance DTS Mode to set up the profiles for a virtual machine storage policies?...

  Can join a Cluster of storage disk out of Maintenance DTS Mode to set up the profiles for a virtual machine storage policies?...

  
  IE can you define the rules of affinity DTS depending on how the rules of storage of profiles are configured for a virtual machine?

  In my mind it seems there is disconnect from the DTS and storage profiles.

  Thank you.

  = NOTE =.

  My lab at home, 2 organizes running ESXi 5.0

  Dv01 has

  Of startup vmfs 7200 RPM 160 G = dv01-BOOT

  Vmfs 1 TB 7200 RPM = VM02-VMFS

  VM02 has

  Of startup vmfs 7200 RPM 160 G = VM02-BOOT

  Vmfs 1 TB 7200 RPM = VM02-VMFS

  Vmfs 5900 RPM 2 TB = VM02-TV01

  I have (3) facility profiles of storage using 'User-defined storage Capablity' as shown below:

  (160 @ 7200 RPM SATA) boot > Boot

  Fast (160 7200 RPM SATA and 1 TB @ 7200 RPM SATA) > fast

  Slow (2 TB @ 5900 RPM SATA) > slow

  Then, I set up a storage Cluster with my local disks on dv01 (only to date)

  LocalVM disc dv01-BOOT and dv01-VMFS disk of the 'cluster of storage.

  I have a computer virtual called DC01 (HardDisk1) want to live on 'Boot' profile storage drive
  His "Non-compliant" poster according to the storage profile, it should run on drive 'boot' on dv01

  To get to this point, I put the StorageCluster in Mode of Maintenace 'DTS' and forced a sVmotion of all virtual machines off dv01-BOOT

  No disks are IO or claim of space.

  But once I take the 'DTS Maintenacne mode' STARTUP dv01 floppy is now get the DTS to return him to satisfy the storage profile (rule) I install... IE do the 'storage profile' VM complient (without doing a few externall API, the PS script or the 3rd party software calls)... ??

  Seems weird it is (or may be) such disconnection of a memory of the profiles and the StorageClusters and the DTS?

  Thank you...

  At this point, I think that storage DRS and storage profiles are two technologies to separate and work independently, but what you suggest is a great idea-

• Change the settings of the HA cluster does not?

  Hello. Strange behaviour in my configuration of HA.

  I got set up with a failover server HA. Now I have to change this configuration, I get an OK message on the paper, but I still see Configuring failover on the summary of the cluster tab.

  If I got to the cluster parameters, it of OK, but is always in the summary the old configuration tab.

  I also have a warning saying that do not have a network of redundant management host. OK, solve this problem, but the message is still there...

  Should I disable - enable the HA to apply these settings? Or it may be a problem of vcenter service?

  Thanks for your help.

  Best regards

  You can try disabling/enabling the AP on the cluster?

  If this does not resolve the problem, I recommend to restart the virtual center.

  MCSE, VCP 310, VCP 410

• VCA Mode change

  Hello
  I'm downgrading to Westmere EVC mode to conform to the old generation of host we add to the cluster.

  To do this, I currently have two clusters created, in production and two hosts using sandybridge.

  the second group has a central server inside and westmere generation.

  I am aware of the procedure found here:VMware KB: VCA allowing on a cluster when vCenter Server is running in a virtual machine

  My question is, rather than quick vMotioning of all hosts another machines.  is it possible to close all virtual machines on a host, set mode now, disconnect the host, move it to the cluster Westmere allow it and then put on all virtual machines?

  I know that I'll still have to disconnect and reconnect my vcenter server, but I would like to avoid having a large amount of machines to vmotion if I can find some downtime to stop all.  and make them move with the host.

  This idea is possible?

  So if I understand what you really want is the future VMs with the host computer, then when you add the host to the new cluster and power them they will run under the new EVC Mode but you essentially in bulk installs what you wanted?

  If so, I did what you describe a bunch of times before (especially during migration between vCenters and want to go to the host and all virtual machines), what I would recommend however keeps the VMs powered on. Disconnect the host and then remove the vcenter. Once removed from the cluster and vCenter connect through thick client and put all virtual machines. Then add it to vCenter, in the cluster you want to and feed the VMS and you would be actually resigned these VMs in bulk.

  Conversely, you can turn off the virtual machines and keep track of those you want to migrate, put the host in maintenance mode and move it to the cluster that you want and then get out of maintenance mode, cold migrates virtual machines and then turn on. I think that this option will be a little easier.

  However, to disconnect a host and removing vcenter will make virtual machines with it, that looks like what you want to do...

• VCA mode disabled / vmotion work?

  We have 2 groups of ESXi at our facility for vSphere, vSphere is version build 5.5U1, currently most recent available.

  Group 1 has Intel Xeon E7540 UC.

  Group 2 is brand new and uses recently published processors Intel Xeon E7-4860 v2.

  VCA is currently disabled on the two groups.

  Athe's systems are listed in the VMware compatibility guide for our latest version of vSphere.

  I expect this Setup to be able to live vMotion of virtual machines from the old to the new cluster without the use of CVS on either, but I assumed that the migration back to group 1 would require cluster 2 to affect the level of reference Intel EVC appropriate (Nehalem in this case).

  It turns out that I am able to migrate VM direct in both directions with no apparent problems (so far), with EVC mode disabled on both groups.

  Is an expected behavior or if ESXi/vCenter is somehow misreading? CPU compatibility (perhaps because the E7-4860v2 are a very recent model) or some other issue that could lead to problems with these migrations?

  I expect this Setup to be able to live vMotion of virtual machines from the old to the new cluster without the use of CVS on either, but I assumed that the migration back to group 1 would require cluster 2 to affect the level of reference Intel EVC appropriate (Nehalem in this case).

  It turns out that I am able to migrate VM direct in both directions with no apparent problems (so far), with EVC mode disabled on both groups.

  Is an expected behavior or if ESXi/vCenter is somehow misreading? CPU compatibility (perhaps because the E7-4860v2 are a very recent model) or some other issue that could lead to problems with these migrations?

  This is normal unless you have turned to bike the VM on the new hosts.

  If a virtual machine has been powered - on on a former host and is migrated to the new cluster, it does not change the current features of the virtual machine CPU runlevel. He will continue to work with the old CPU features on the new host and is therefore able to migrate the old new host without problems, or additional AIDS such as CVS.

  However, if stop you now migrated virtual machine and power it on again on new hosts, the virtual material will apply the new host CPU capabilities (or the level of EVC of cluster, but you do not apply any) and you will not be able to migrate the computer virtual return to the armies of the former cluster.

• VCA mode

  I try to enable CVS mode on a cluster, but get the message "host is not allowed in the compatibility mode of the current cluster Enhanced vMotion.". Under voltage or suspension of the virtual machines on the host can use CPU features hidden by fashion. ».

  The Group had initially 2 servers Dell PowerEdge R810 with dual cpu Intel Xeon E7540. I am trying to add 2 older servers Dell PowerEdge R900 with quad cpu Intel Xeon E7320. I'm guessing it wont let me enable it because virtual machines under tension using the more recent servers (R810) and their cpu. My guess is correct? I need to power all of my virtual machine to enable CVS or y at - it another way to activate?

  Hello

  Yes your proposal was correct. You can disable all your virtual machines to the VCA mode.

  More information about the activation of the CVS: VMware KB: VCA allowing on a cluster when vCenter runs in a virtual machine

  Kind regards

  Julien

• Satellite A300 1J1 - Recovery Mode "Expert" to change the size of the partition

  I'm trying to reconfigure the size of the partition of windows with the recovery partitions as I don't like the idea of having the poit drive 50-50.

  I would like therefore to reduce it so that only the data of recovery will be adapted on the D drive and my main partition will be much greater. IE C: = 240 GB + and the recovery drive (d) will be only 5 GB (large enough for recovering data only.)

  I posted this thread here a few days ago.

  [http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=132571𠗛]

  This and the search of these forums has gotten me to the point where I think I need to use the DVD of recovery in "EXPERT" mode This should allow me to set the partitions manually rather than automatically right in the Middle!

  I noticed that the screen asking me what to install has a SETTINGS option that is always grayed out.

  Does anyone know how to open the SETTINGS screen, or if there is another way to create the partitions manually?

  Thanks for any response.

  Hello

  I have already replied to the other thread (see the link in your message)

  The point is that you cannot resize partitions using the Vista Toshiba Recovery DVD.

  Mentioned Expert mode is not available in the Vista recovery DVDs.
  The expert mode is part of the Win XP Recovery CD.

  However, the fact is that the Vista recovery DVDs sets the laptop to factory settings and also the size of the partition.

  The sizes of the partitions can be modified in the Vista Disk Manager!

  Good bye

• My iPad detects inactivity while I'm listening to a story.  Then he slips into the mode "sleep" and interrupts the story.  Any suggestions on how to avoid this?

  My iPad detects inactivity while I'm listening to a story.  Then he slips into the mode "sleep" and interrupts the story.  Any suggestions on how to avoid this?

  Setting to never by using the auto-lock settings application.

  Settings > general > auto lock > never

• R6300 Bridge Mode Wifi settings

  I have the settings wireless on my main R6300 router to be awakened at midnight every night. I plan on setting up my second R6300 in Bridge mode in another room connected via Lan to Lan. These are the two routers in R6300 version 1.

  I'm sure I know the answer but want to make sure... I want the wireless signal to be awakened at midnight on my second router also.

  My question is, do I have to do it manually in the settings of the router second or second router just an extension of the first, so turn off the signal at midnight wireless also?

  HaHa. My bad.

  Yes, I will link two routers with an ethernet cable, which is a set up access point would be in Bridge Mode. Never realized that until you said it.

  I go ahead and close this thread and put the second router in AP mode and manually disable the signal wireless at the time wherever I choose.

  Another small issue however, Lan, Wan or Lan to Lan for installation in AP mode? I see pictures of Lan to Wan but have read where Lan to Lan is used.

  Thank you.

• move the cluster for sub vi

  Hello

  I want to spend a cluster that can change its content to one under VI. The cluster does not change by program, but during programming, that is, I could add or remove items in the / cluster. Using direct wire or local variables I would have to change each sub VI that uses the cluster updated the. I also tried the typedefs, but I met the same problem.

  At the same time the Subvi should be able to update the cluster I spent.

  In C++, I use classes like struct (equivalent to the cluster of LV) and pass a pointer to a class object to a function. Within the function, I choose the members of the class I want to use inside this function. If I change the class structure, the functions of the Word are not affected (of couse only as long that I remove irrelevant of class members of the called function).

  Example (from C++):

  settings * param;  'settings' is a class that I use to group variables

  doSomethingUseful (param);

  / * the doSomethingUseful function uses the pointer to parameter and accesses the members of

  Param-> variable1

  Param-> variable2

  ...

  Hereby, I can change the values of variables stored in the param object

  */

  Best,

  Max

  
  

• You try to run the scan mode and mode interface fpga at the same time is causing errors

  I'm reading a 9236 9237 and a 9215 with the scanning engine and read from two 9211 modules with the fpga. It's because I need to acquire to 200 Hz with the 9236 9237 9215 but maximum rate of the scan engine is limited by the slower module in the system, which in this case is the max of 15 hz the 9211.

  So to use both interfaces (scan engine and fpga), I followed the percisely given in this article for instructions.

  1. the project has created and added the peripheral crio using the interface of the scan engine.

  2. Add the target fpga and drag and drop the 9211 inside modules

  3. has created the fpga in interface file with and compiled with no error.

  4. interfaced with the file fpga at almost exactly the way the sample project of "getting started with 9211' by using the engine of analysis in the interface with the other modules.

  5. after the errors to discover that I created a VI that tests for just the portion 9211 code (called "thermocouple FPGA method Test.vi")

  The data returned by the interface fpga was nothing else than zeros on all channels, even if thermocouples were hooked on some of them. (all zeros as entries in the convert temperature vi gives-410, 6160 degrees F, if you happen to have the material to try this.)

  I get the following error from the open fpga vi reference:

  code error-61141
  "Thermocouple method Test.vi FPGA.
  Activities FPGA:
  
  Open FPGA interface reference.
  Reserved outside LabVIEW FPGA:  turns The RIO Scan Interface.  You must set the mode Interface FPGA chassis in order to unlock the FPGA. »
  

  It's extremely frustrating, because as I explained, I've been very attentive not only follow the instructions for concurrent fpga and analysis but also to model my VI by the example of VI, even if only for the moment, just to try to work things out.

  Any help would be appreciated as I need to fix this for the further development and I am somehow in a lack of time. I opened a support ticket (reference #7256226), but the app engineer had no time to answer.

  My system:

  cRIO-9014 controller RT with crio-9104 bottom of basket.

  LabVIEW 2009

  Latest drivers and peripheral software pc and rio (RIO scan 3.2 engine support june2009)

  rex1030 wrote:

  I'm reading a 9236 9237 and a 9215 with the scanning engine and read from two 9211 modules with the fpga. It's because I need to acquire to 200 Hz with the 9236 9237 9215 but maximum rate of the scan engine is limited by the slower module in the system, which in this case is the max of 15 hz the 9211.

  This should not be the case.  9211 data will not update with each sweep, but you should be able to run the scan faster than 15 Hz without problem.  Do you have specific issues with this?

  So to use both interfaces (scan engine and fpga), I followed the percisely given in this article for instructions.

  1. the project has created and added the peripheral crio using the interface of the scan engine.

  2. Add the target fpga and drag and drop the 9211 inside modules

  3. has created the fpga in interface file with and compiled with no error.

  4. interfaced with the file fpga at almost exactly the way the sample project of "getting started with 9211' by using the engine of analysis in the interface with the other modules.

  5. after the errors to discover that I created a VI that tests for just the portion 9211 code (called "thermocouple FPGA method Test.vi")

  You can try making sure that the chassis is set to mode Interface FPGA and the setting is deployed.  I wrote that article that you referenced says will select the deploy option later and not explicitly speak to deploy the chassis later.  Run a VI with a reference open FPGA vi not automatically deploy chassis settings if you need to do it explicitly.  Try the following steps.

  1. right click on the frame element and select Properties.  Make sure that the Interface FPGA option button is selected. \

  2. right click on the frame element and select deploy.

  3. repeat your VI.

  The data returned by the interface fpga was nothing else than zeros on all channels, even if thermocouples were hooked on some of them. (all zeros as entries in the convert temperature vi gives-410, 6160 degrees F, if you happen to have the material to try this.)

  I get the following error from the open fpga vi reference:

  code error-61141

  
  "Thermocouple method Test.vi FPGA.
  Activities FPGA:

  Open FPGA interface reference.
  Reserved for LabVIEW FPGA outside: The RIO Scan Interface is running. You must set the mode Interface FPGA chassis in order to unlock the FPGA. »

  The likely cause of this error is that the setting of the FPGA Interface on the chassis has not been deployed.  If the chassis is still Mode Scan fixed personality bitfile will be loaded on startup and the FPGA will be locked.

  It's extremely frustrating, because as I explained, I've been very attentive not only follow the instructions for concurrent fpga and analysis but also to model my VI by the example of VI, even if only for the moment, just to try to work things out.

  I'm sorry that you have had difficulties.  Assuming that I'm wrong about the source of your problem, it seems we have to update less than Ko to include the deployment step.

  Any help would be appreciated as I need to fix this for the further development and I am somehow in a lack of time. I opened a support ticket (reference #7256226), but the app engineer had no time to answer.

  My system:

  cRIO-9014 controller RT with crio-9104 bottom of basket.

  LabVIEW 2009

  Latest drivers and peripheral software pc and rio (RIO scan 3.2 engine support june2009)