vCenter 5.1 - Nessus scan results and remediation

Similar Questions

• My Photosmart 3210: when scanning slides 35 mm, the scan results in a single image

  Photosmart 3210 all-in-one

  Mac OS 10.6.8

  HP software: HP_Installer_Photosmart_Full_Group12_10.3.dmg

  This is my 1st attempt to digitize old 35mm color slides. At the first trial, the scanner produces four good images. On the next sweep attempts, it produces only a single image containing four slides and a message in the printer says "no scan options".

  I tried your troubleshooting ideas: unpluggng the printer, uninstall/reinstall the software HP & pilot.

  All other functions of the word OK printer. Any ideas?

  macintod

  Thank you, Sean.   Scanning is now the induvidual pictures production. But I had todo several other procedures.

  I have reset the printer according to your instructions, but it had the same negative results.

  I then unplugged the power from the printer and the signal cables, and then reconnected them and restarted the printer. I then reset the printer by you instructions.  I restarted my iMac's "HP Scan", selected slides in the HP scan profiles and pressed 'Scan '.  The result was four individual images.

  Thank you very much.   macintod

• You try to run the scan mode and mode interface fpga at the same time is causing errors

  I'm reading a 9236 9237 and a 9215 with the scanning engine and read from two 9211 modules with the fpga. It's because I need to acquire to 200 Hz with the 9236 9237 9215 but maximum rate of the scan engine is limited by the slower module in the system, which in this case is the max of 15 hz the 9211.

  So to use both interfaces (scan engine and fpga), I followed the percisely given in this article for instructions.

  1. the project has created and added the peripheral crio using the interface of the scan engine.

  2. Add the target fpga and drag and drop the 9211 inside modules

  3. has created the fpga in interface file with and compiled with no error.

  4. interfaced with the file fpga at almost exactly the way the sample project of "getting started with 9211' by using the engine of analysis in the interface with the other modules.

  5. after the errors to discover that I created a VI that tests for just the portion 9211 code (called "thermocouple FPGA method Test.vi")

  The data returned by the interface fpga was nothing else than zeros on all channels, even if thermocouples were hooked on some of them. (all zeros as entries in the convert temperature vi gives-410, 6160 degrees F, if you happen to have the material to try this.)

  I get the following error from the open fpga vi reference:

  code error-61141
  "Thermocouple method Test.vi FPGA.
  Activities FPGA:
  
  Open FPGA interface reference.
  Reserved outside LabVIEW FPGA:  turns The RIO Scan Interface.  You must set the mode Interface FPGA chassis in order to unlock the FPGA. »
  

  It's extremely frustrating, because as I explained, I've been very attentive not only follow the instructions for concurrent fpga and analysis but also to model my VI by the example of VI, even if only for the moment, just to try to work things out.

  Any help would be appreciated as I need to fix this for the further development and I am somehow in a lack of time. I opened a support ticket (reference #7256226), but the app engineer had no time to answer.

  My system:

  cRIO-9014 controller RT with crio-9104 bottom of basket.

  LabVIEW 2009

  Latest drivers and peripheral software pc and rio (RIO scan 3.2 engine support june2009)

  rex1030 wrote:

  I'm reading a 9236 9237 and a 9215 with the scanning engine and read from two 9211 modules with the fpga. It's because I need to acquire to 200 Hz with the 9236 9237 9215 but maximum rate of the scan engine is limited by the slower module in the system, which in this case is the max of 15 hz the 9211.

  This should not be the case.  9211 data will not update with each sweep, but you should be able to run the scan faster than 15 Hz without problem.  Do you have specific issues with this?

  So to use both interfaces (scan engine and fpga), I followed the percisely given in this article for instructions.

  1. the project has created and added the peripheral crio using the interface of the scan engine.

  2. Add the target fpga and drag and drop the 9211 inside modules

  3. has created the fpga in interface file with and compiled with no error.

  4. interfaced with the file fpga at almost exactly the way the sample project of "getting started with 9211' by using the engine of analysis in the interface with the other modules.

  5. after the errors to discover that I created a VI that tests for just the portion 9211 code (called "thermocouple FPGA method Test.vi")

  You can try making sure that the chassis is set to mode Interface FPGA and the setting is deployed.  I wrote that article that you referenced says will select the deploy option later and not explicitly speak to deploy the chassis later.  Run a VI with a reference open FPGA vi not automatically deploy chassis settings if you need to do it explicitly.  Try the following steps.

  1. right click on the frame element and select Properties.  Make sure that the Interface FPGA option button is selected. \

  2. right click on the frame element and select deploy.

  3. repeat your VI.

  The data returned by the interface fpga was nothing else than zeros on all channels, even if thermocouples were hooked on some of them. (all zeros as entries in the convert temperature vi gives-410, 6160 degrees F, if you happen to have the material to try this.)

  I get the following error from the open fpga vi reference:

  code error-61141

  
  "Thermocouple method Test.vi FPGA.
  Activities FPGA:

  Open FPGA interface reference.
  Reserved for LabVIEW FPGA outside: The RIO Scan Interface is running. You must set the mode Interface FPGA chassis in order to unlock the FPGA. »

  The likely cause of this error is that the setting of the FPGA Interface on the chassis has not been deployed.  If the chassis is still Mode Scan fixed personality bitfile will be loaded on startup and the FPGA will be locked.

  It's extremely frustrating, because as I explained, I've been very attentive not only follow the instructions for concurrent fpga and analysis but also to model my VI by the example of VI, even if only for the moment, just to try to work things out.

  I'm sorry that you have had difficulties.  Assuming that I'm wrong about the source of your problem, it seems we have to update less than Ko to include the deployment step.

  Any help would be appreciated as I need to fix this for the further development and I am somehow in a lack of time. I opened a support ticket (reference #7256226), but the app engineer had no time to answer.

  My system:

  cRIO-9014 controller RT with crio-9104 bottom of basket.

  LabVIEW 2009

  Latest drivers and peripheral software pc and rio (RIO scan 3.2 engine support june2009)

• Could Scan mode and FPGA mode be used in a project?

  Hi all

  I need a project that the current NI9203 with mode of analysis samples and samples of the accelerometer of the NI 9237 with FPGA mode. It could be achieved? Could Scan mode and FPGA mode be used in a project?

  I use labview2009.

  Thank you very much.

  Yes, they can. This mode is called hybrid mode. To use the Mode of LabVIEW FPGA IO modules, simply slide the module to the target FPGA in the LabVIEW project, disconnected from scan mode. Then use LabVIEW FPGA to program the modules and use I/O variables for read and write I/O on the remaining modules. When you use a LabVIEW FPGA Mode on one or more modules, the logic of the scan Mode CompactRIO on the FPGA, known as the RIO Scan Interface, is compiled in a single application of FPGA with LabVIEW FPGA VI. If no module is configured to use the scan mode, the RIO Scan Interface is not included in the compilation.

• scanning voltage and current measurement for Keithley 2400

  Dear all

  Hello

  can someone help me?

  Despite days nearlly10 I am option to find any program LabVIEW 2010 for sweeping the voltage and measure current who works with RS-232, I have a end not have nothing exept examples read single and multiple data. I tried to SmartData labview and changed a few prorgram gpib to RS - 232, but I couldn't.

  In another attempt to find a good VI "votltage scanning and current measurement" that work with RS-232 in labview 5.1.1. I have converted in 2008, but it takes old driver (ke24xx.dll) and do not work in my labview 2010 and I could ' t find older driver.

  My thesis project was halted in those 10 days, and I couldn't do anything for our keithley.

  Please helpe...

  in the following, I have attached these files:

  1.-first, what voltage scan that works with GPIB

  2 - Vi that I change the gpib for visa (rs232) port that I don't know why it doesn't work.

  3. it is Vi related to the "sweeping and current measurement votltage" that works with the RS-232, but it takes old dirver so I can't use it.

  4-slot-VI necessary for the implementation of program 3 (but there is no driver for these subVIs) was attached to the reply message of this post

  If any body has this program ("scan votltage and current measurement" running rs - 232) please send to me

  Thanks in advance.

  None of you attached the screws are the driver OR you spoke. There is no conversion required for this driver.

• I need to scan documents and put it in a file how to do this

  I need to scan documents and then also add a file how to do this

  Hello

  1. what operating system is installed on your computer?

  2. which file you want to add the scanned data?

  What version of the operating system Windows am I running? :

  http://Windows.Microsoft.com/en-us/Windows7/help/which-version-of-the-Windows-operating-system-am-i-running

  You must have a device Scanner to scan a document.

  If you have a scanner device, please read the manual carefully to have a clear idea of it.

  Please provide us with more information to solve the problem as soon as possible.

  For reference:

  Scan a document or a file:

  http://Windows.Microsoft.com/en-us/Windows-Vista/scan-a-document-or-file

   

  I hope this helps.

• Scan photos and 600 dpi tiff and save them to a USB flash drive

  I want to scan pictures and 600 dpi tiff and save them to a USB flash drive, but won't my canon mg6220

  Let me bad format.  Any ideas or suggestions would be greatly appreciated.

  Thank you, Fred

  Hi fredno,

  If you scan directly on the USB key using the Control Panel, you are limited to the use of JPG or PDF format.  To analyze the TIFF, you will first need to analyze the images on your computer, then copy them to the USB key.

• Scanned images and documents seized by my HP Officejet 4500 are spread

  The first time that we put in place our Officejet 4500 All in one it failed the test of alignment, where you print a test page, and then the scanner.  The printer would be message has failed this test and it would be back to the default settings.  This doesn't seem to be a problem initially becaue the printer works great, but recently I needed to scan documents and all my scans come out slightly offset, as the type turns a little diagonally across the entire page instead of 90 degrees as the original document.  I found a few times, if the document feeder this problem was less pronounced in the first pages of one or two.  Tonight no luck.  All the scans have been distorted.   I look at the scanner through the glass, it looks like the scan head is twisted.  The printer will shake in a straight position, but when you close the lid, the printer is a kind of mechanical movement alignment and when I lift the lid it addressed again.   What type of aligning the procedure I do get good analyses straight and copies?   HELP is appreciated.

  Thank you, image scanned on the glass, you can clearly see distortion (not just tilt), probably due to an irregular movement of the scan bar. When you see distortions like this, it's generally the hardware problem and scanner must be repaired.

• I have microsoft scan software and a jet hp6500 office printer, scanner etc. How can I scan to a PDF file?

  I have microsoft scan software and a jet hp6500 office printer, scanner etc.  How can I scan to a PDF file?

  Hello Jim,

  I will suggest 2 things. First, go to hp.com site and select your device from the five listed here (http://www8.hp.com/us/en/support-drivers.html).

  Second suggestion is that you use the HP software to scan your document, where the native format is PDF.

  Let me know if this helps you.

  Kind regards

  BearPup

• I am a beginner using Muse. Google shows all pages menu in the search results and all texts on these pages. How to just display the home page?

  I am a beginner using Muse. Google shows all pages menu in the search results and all texts on these pages. How to just display the home page?

  Thank you. I thought I created my Muse wrong site.

• Trying to send a scanned document and I get an error of missing file: api-ms-win-crt-string-11-1.0.dll never had a problem before and I've recently updated to the office of 2016 and that's when I got this message.

  Trying to send a scanned document and I get an error of missing file: api-ms-win-crt-string-11-1.0.dll never had a problem before and I've recently updated to the office of 2016 and that's when I got this message.   Anyone know if it's related to Adobe or Outlook?  I am able to send emails on Outlook.

  Thank you

  Hi lorid74531323,

  Latest version of MS office will not work with your Acrobat 9.

  May be a compatibility issue, please check the web browsers and applications of PDFMaker

  Kind regards
  Nicos

• When I installed the web client vsphere using vcenter server iso, encounted an error that the vcenter server signon administrateu use name and password is invalid

  VCenter server is version 5.1 and this server is a member of the working group.

  It comes to my administrator:

  

  So, I used ISO server vcenter and installed web client pulg-in vsphere, it prompted:

  I've used many ways, but failed.

  usernme:admin@system-domain,

  so, I do not know how to solve, and I only know this administrator password.

  I'm not vCenter sign the only to have another admin, please help.

  

  and another question: how install and configure the data via the vsphere 5.1 customer protection, vsphere isn't vsphere web client.

  You must provide credentials for the user admin@system-domain.

• Service server vmware vcenter orchestrator on local computer started and then stopped

  Hello

  I'm unable to start the Server service of vco on Windows 2008 R2 machine. If I try to restart the service it displays the following error;

  "Service server vmware vcenter orchestrator on local computer started and then stopped. "Some services stop automatically when not in use by other services or programs.

  Can someone give me the solution for this?

  Thank you

  Radhika

  First check the configuration of the vCO application and that all green lights. If this isn't the case difficulty what the problem is.

  If everything is green, see the server.log file and look for FATAL / ERROR.

• After the merger of 7 shots in panorama, it took about 5-6 minutes to get the end result and the result had only something above 1000 pixels.

  After the merger of 7 shots in panorama he tooks nearly 5-6 minutes to get the final result and this result have only something above 1000 pixels edge long photo resolution? Why is this happening? I've been fusion 7 24Mpix of Nikon D750 RAW files. I saw a promo video where he introduced and there the panorama was above 10 000 pixel wide, so it is not a limit of lightroom, but something is not. Maybe some strange décor? Thank you.

  Well, the good news is... This isn't your files.

  I produced a pano 17310 x 6039 in less than 3 minutes. With or without adjustment.

  The only differences that we have so far is the platform. Mac/Pc

  Wrong guess you managed to repeat the question. Maybe a reinstall?

  I hope that someone else (on PC) may be able to provide alternative suggestions. Let us know if you yourself are able to find a solution.

• Can message 'No result' and filters to OBIEE - we change this?

  Hello Experts,

  OBIEE default behavior when no data is returned for a given query should display the message "No Results" and a list of used filters (if any) for the criteria.

  Image: http://tinypic.com/m/hv2q9c/4

  Is it possible to edit this message and remove the display filters?

  Thanks in advance.

  Check this https://forums.oracle.com/forums/thread.jspa?threadID=2502202&tstart=0