Version hardware VM and the host versions

Similar Questions

• Virtual LAN with guests and the host only

  Hello

  I have a win server 2008 r2 host and a couple of virtual machines.

  I want to create a VLAN that contains the host and guest of the virtual machine. I intend to host the domain controller.

  I put the network connection from the guest to "host-only '.

  Then I tried ping between the guest and the host. Ping fails. "request time out" @host and "destination host unreachable'@guest.

  Firewall is turned off on both.

  What could be the problem? Is there another way to reach my goal?

  Kind regards

  Dembele.

  Did you stop the firewall service, or you have turned off the firewall? Stopping the service does not work.

  In any case, take a look at for example example 4 in the http://support.microsoft.com/kb/947709/en-us for how to configure ICMP (ping) settings.

  André

• Dedicated network adapter to the virtual machine and the host computer not let can visit his profile

  OK, here's my question, I know how to give themselves a phyiscal nic to a vmware, but I wanted to take it one step further and do not leave the host send or receive data from this network card, only the virtual machine can use this network/NIC...

  Here's my reasoning, I have to network conections, one is for my internal/field network and the second is a direct connection to the internet (Comcast) I don't want to use to separate the machines have for internet connection, I want to be on the same machine phyiscal and have just the vmware machine talking to comcast... is it possible?  I am running VMware workstation 7, last update.

  Thank you

  Cdrshm

  I assume you are using a Windows host?

  If Yes...

  -first set up networking networking with vmnetcfg.exe

  -assign vmnet0 to the network card for the internal network

  -assign vmnet2 to the network card used for direct access to the internet

  -Right-click on the map network-icon in the systray and access the properties of the network adapter for vmnet2

  -Disable all other protocols and the Protocol of vmware_bridge for this network adapter

  result: a virtual machine that uses vmnet2 can directly access the internet and the host has no IP address for this network adapter - and therefore cannot use it.

  _________________________

  VMX-settings- WS FAQ -[MOAcd | http://sanbarrow.com/moa241.html]- VMDK-manual

• Update VUM 5.1 to 5.5 with a base with host and the host upgrades patches

  We are currently running vCenter 5.5.0c with 5.1u1 on all hosts.  We have lines of base (2) attached to these hosts.  One of these baselines is dynamic with all the latest patches to be applied and the other baseline is the upgrade to 5.5.0a.  We have not restored over several months and I have a question.  If I leave two reference levels, AUVS will know to run the upgrade first and then patch the latest version?  I want to just make sure THAT VUM does not apply time to 5.1 before moving to 5.5 patches.  If there is not a good answer on that, the plan is to detach the dynamic baselines with all the patches and it reinstall manually after the upgrade to 5.5.  Management doesn't like going to the latest versions and the plan is to actually update it 5.5.0a, because it is later (update1) HP.  We go to patch after that, while the server is in maintenance mode, but I didn't at the margin of the baselines set if it can run 5.1 patches before moving to 5.5.  I excluded the cumulative 5.5 update1 for our dynamic patch database.

  Thank you

  When you click on clean up host you choose the database Type, then do not worry, just select upgrade basic :-)

  

• The hardware upgrade and the cabinet on a PC running genuine Win XP!

  Hello... I use Beanstalk (Bought in 2002) HCL with original Win XP and I want to change the old motherboard (microATX) and the processor and the ram for a breakthrough because I had more problems with the former. But because of my size the new motherboard (ATX), I have to change the furniture too. The firm HCL contains the thumbnail of Windows authentication. I'll change the furniture and equipment and sell the former. How to change the windows license from the old to the new configuration without having to purchase a new license?

  A sticker placed on the PC "case" tends to mean that it is an OEM version.  OEM versions, by the terms of license AGREEMENT, are "forever" related to the first PC that is installed on.  The 'sense' standard and accepted PC can also be interpreted as 'mother '.  Substitute her means that the motherboard you would have a new PC at the end of the "improvements".

• Need hardware Configuration of the host Machine

  Hello

  I want to install the 3Vm on me Desktop.

  Please suggest me the office/capacity hardware configuration: -.

  Purpose: -.

  • I need to run 3 VM's (VMWARE) parallel on Windows 8 (64-bit) host computer.
  • Each required VM, 4GB of RAM
  • I'll run Oracle Application/database and the application of the merger on the virtual machine.
  • I need more HD 1 TB.

  Please send me the details of hardware configuration.

  Thank you

  ANUP

  Hey extreme,

  Welcome to the VMware community.

  I suggest you go with a desktop computer with the following configuration

  Processor: Intel Core i7 or AMD equivalent

  RAM: 16 GB minimum (32 GB would be great)

  HD: Buy 2 X 2 to disks. everywhere where it allows it, use a provisioning so that you know if you actually use to the top of the storage.

  Alternatively, you can also buy a motherboard of the server with xeon processor and install ESXi directly on it.

• A few questions regarding the hardware upgrade and the games on Satellite Pro 2100

  Hey,.

  I thought that posting this here because it's more about the lines for the games I could think on another topic.

  I'll get to the point... Basically, I bought a laptop from a guy that my friend knew. He barely used this laptop and didn't know anything about computers, and he tried to avoid as much as possible. So he got rid of this laptop for me for real cheap.

  Now I got it, I had expected either of two things with the laptop.

  (1) what I'll use it so I can sit in his bed and travel a little bit while having files, movies, music and internet access. (it wasn't my main idea)

  Or

  (2) it allows to play video games on it, or to update, so I have a better chance to do so.

  I was hoping to get for video games, mainly for my brother to use because his computer is lagging a lot while playing world of Warcraft. I was hoping that this notebook would give him a better experience for a while.

  But as I was installing the game on this, I noticed that the disk space is low, so I'm going to buy an external hard drive, so I can send files between the PC and the laptop, and I got an error message saying that the RAM was under "minimum requirements" for WoW.

  So I know that I got to level it with something big, but I know not what, so I'm not quite sure that this laptop will run the game at a decent rate. So I thought that I turn to a computer forum and ask.

  It's my laptop;
  [Satellite Pro 2100 PS210E | http://uk.computers.toshiba-europe.com/innovation/jsp/SUPPORTSECTION/discontinuedProductPage.do?service=UK&BV_UseBVCook = Yes & PRODUCT_ID = 45659 ie]

  This laptop will do the job don't you think?
  Or it will be better for simpler things, or less if I had the ram to 1gig?

  I don't know much on the laptop, and I'm not really willing to spend too much on fixing, if it's just a change of the ram, then it wouldn't cost much for than to upgrade around 1gig.

  Hello

  First of all, I must say that this notebook belongs to an older series laptop.
  It was equipped with the 1.8 Celeron CPU, 256 MB RAM, 20 GB or 30 GB HARD drive and a 16MB graphics card internal.

  What you can do is upgrade the RAM up to 1 GB (2 x 512 MB) and the HARD drive. But I think that the maximum size of HARD drive that would be recognized by the BIOS is 120 GB.
  I think that the laptop supports one IDE controller and it limited because of the 28-bit LBA HARD drive size.

  So finally, it is important to mention that you can not pass the graphics card because it s soldered onto the motherboard. Upgrading the CPU is not possible or very difficult.

  I come to the conclusion that you will not be able to play games of new generation on this machine. The hardware specs are maybe too low a few simple games would run on this laptop but I'm sure that other newer games will not run smoothly.

  Welcome them

• System Restore and the host file

  How do you keep restoring the system to unblock web sites in the hosts file?

  Hello

  System Restore is not designed to do what you want it to do.

  A system restore point contains the settings of the computer at that moment in time.

  It's the idea of system restore.

  http://Windows.Microsoft.com/en-pH/Windows-Vista/what-is-system-restore

  "System Restore helps you restore system files from your computer to an earlier point in time. Is a way to cancel the system changes to your computer without affecting your personal files.

  "These restore points contain information about registry settings and other system information that Windows uses."

  See you soon.

• Remote Desktop - conflict between the remote control and the host user?

  We set up Microsoft Remote Desktop on a Mac with a remote computer that is running Windows 7 Professional.

  What happens when:

  1. the remote user tries to connect to the Windows host computer while someone is working on it?

  2. a person is trying to work on the host computer, and the remote user is logged?

  Is the second locked user, is there a warning of the conflict, or is there another way that Remote Desktop manage such a conflict?

  DRM for any assistance you can provide.

  Stuart A. Forsyth

  E-mail address is removed from the privacy *.

  Hi Stuart,

  Thanks for posting your question on the forum of the Microsoft community.

  The question will be better suited to the audience of professionals on the TechNet forums.

  I would recommend posting your query in the TechNet forums.
   
  TechNet Forum
  http://social.technet.Microsoft.com/forums/en-us/home?category=w7itpro

  For reference:
  http://Windows.Microsoft.com/en-us/Windows/Remote-Desktop-connection-FAQ#1TC=Windows-7

  Thank you

• IKEv2 - xml file and the host name

  Hello world

  Ikev2 anyconnect works very well in the PC.

  Xml file in c\programs data\profile PC hostname say anyconnect_ikev2.

  Under the ASDM - anyconnect profile I changed the host name to say xyz.com.

  Then PC I tried to connect again and found that the connection has been established and the hostname under xml view profile: PC go to xyz.com.

  Need to know how the PC has managed to connect even if the host name has changed?

  Concerning

  MAhesh

  Mahesh,

  The client connects to the base on the HostAddress profile field.

  Host name, is what is used to populate the drop-down list and identifies the connection in "plain language." Although it is often the COMPLETE domain name, it doesn't have to be.

  When a user makes the connection, one of the things that happens is that any changes in profile on the ASA is pushed to the locally stored user profile.

• vCenter shows all virtual machines and the host is disconnected

  Hello

  I have a two nodes in the cluster ESXi6 U2 (recently updated to 5.5) running on hp dl380p gen8. For some reason all the virtual machines are running on host A (HA and DRS are enabled).  vCenter shows all virtual machines and host A is disconnected. Cannot connect to A host using vSphere client or web client. Cannot vMotion the VMs. Impossible to activate SSH. Connection DCUI works very well. Cannot perform any action VM

  All virtual machines are in place are running at this point. I don't want to restart the virtual machines. Can you help me please?

  Thank you

  AJ

  Frozen screen DCUI came back to life. The active SSH access, killed the running process. The host of running backs.

  See you soon,.

  AJ

• Question of HDD of VM and the host.

  OK, so my new set upward is a box of esxi with a virtual machine of win2k3. I have 2x1To hard drives and a 40 GB running the esxi and virtual machine of win2k3 data store.

  How could I make the win2k3 connect to the host's hard drive? can I do straight out or what? It will change the format?

  If you do not have a VMFS partition on them you can show them as RDM devices at the prompt:

  http://pubs.VMware.com/vsp40u1_i/server_config/c_about_raw_device_mapping.html

  http://pubs.VMware.com/vsp40u1_i/server_config/c_managing_mapped_luns.html

  AWo

  VCP 3 & 4

  \[:o]===\[o:]

  = You want to have this ad as a ringtone on your mobile phone? =

  = Send 'Assignment' to 911 for only $999999,99! =

• Relationship between memory of comments and the host memory usage

  Hello

  I noticed today that the memory usage of my cluster rose close to 90% in all of the blades. I checked and found that a number of virtual machines is everyone using over 3 GB of memory host. When I went in the performance monitor for each of these virtual machines, they used only a maximum of 400 MB.

  How the memory usage of comments relate to the host memory usage, and how I can reduce the amount of memory used host so I do not have a performance hit through the cluster?

  Running ESX 3.0.2, VC 2.0.2 Dell Poweredge servers with 2 processors 1.86 GHz quad core and 24 GB of RAM.

  See you soon

  Graeme

  You can learn more about memory usage http://www.vmware.com/pdf/esx3_memory.pdf and resource management guide http://www.vmware.com/pdf/vi3_35/esx_3/r35u2/vi3_35_25_u2_resource_mgmt.pdf

  If you found this information useful, please consider awarding points to 'Correct' or 'useful '. Thank you!!!

  Kind regards

  Stefan Nguyen

  VMware vExpert 2009

  iGeek Systems Inc.

  VMware, Citrix, Microsoft Consultant

• Script to list all the warehouses of data in a cluster, the virtual machines on the data store and the host of the virtual machine is on

  We have warehouses of data which are seen by more than one cluster. I need a script that will display:

  all stores of data seen by a cluster

  the virtual machines on the data store

  the host of the virtual machine is on

  the cluster the host is in

  The output I want is

  name of the store of data, the VM name, host name, the name of the Cluster

  any help would be appreciated

  Pretty sure this will do what you need:

  $report = @()
  Foreach($cluster in Get-Cluster){
      $datastores = $cluster | Get-VMHost | Get-Datastore
      foreach($datastore in $datastores){
      $vms = $datastore | Get-VM
      If ($vms.count -ge 1){
          foreach($VM in $vms){
          $object = New-Object -TypeName PSObject -Property @{
                Datastore = $datastore.Name
                VM = $VM.Name
                HostName = $VM.VMhost
                Cluster = $cluster
              }
          $report += $object
          }
  
      }
      }
  }
  $report | Export-Csv C:\Temp\VMs.csv -NoTypeInformation -UseCulture
  

  If you only want to shared data warehouses you can then use

  $datastores = $cluster | Get-VMHost | Get-Datastore | Where {$_.Extensiondata.Summary.MultipleHostAccess -eq $True}
  

  Hope this helps

• Is it possible for the participants to see only the host and the host to see all participants (webcam)?

  I want to be able to see the webcams of all participants in the room, if they have active, but all participants must only be able to see the host from the host. Is this possible?

  No, the view is the same for everyone in the room, regardless of the role within the room.