Virtual ASAv using for remote access

Similar Questions

• How to use ACS 5.2 to create a static ip address user for remote access VPN

  Hi all

  I have the problem. Please help me.

  Initially, I use ACS 4.2 to create the static ip address for VPN remote access user, it's easy, configuration simply to the user defined > address assignment IP Client > assign the static IP address, but when I use ACS 5.2 I don't ' t know how to do.

  I'm trying to add the IPv4 address attribute to the user to read "how to use 5.2 ACS", it says this:

  1Ajouter step to attribute a static IP address to the user attribute dictionary internal:

  Step 2select System Administration > Configuration > dictionaries > identity > internal users.

  Step 3click create.

  Static IP attribute by step 4Ajouter.

  5selectionnez users and identity of the stage stores > internal identity stores > users.

  6Click step create.

  Step 7Edit static IP attribute of the user.

  I just did, but this isn't a job. When I use EasyVPN client to connect to ASA 5520, user could the success of authentication but will not get the static IP I set up on internal users, so the tunnel put in place failed. I'm trying to configure a pool of IP on ASA for ACS users get the IP and customer EasyVPN allows you to connect with ASA, everything is OK, the user authenticates successed.but when I kill IP pool coufigurations and use the "add a static IP address to the user 'configurations, EzVPN are omitted.

  so, what should I do, if anyboby knows how to use ACS 5.2 to create a user for ip address static for remote access VPN, to say please.

  Wait for you answer, no question right or not, please answer, thank you.

  There are a few extra steps to ensure that the static address defined for the user is returned in the Access-Accept. See the instuctions in the two slides attached

• AnyConnect 3.0 supports IPSec VPN for remote access?

  Hello world

  I've read about Cisco AnyConnect 3.0 issues that it supports IPSec VPN for remote access:

  http://www.Cisco.com/en/us/prod/collateral/vpndevc/ps6032/ps6094/ps6120/qa_c67-622477_ns1049_Networking_Solutions_Q_and_A.html

  I downloaded and installed the Client AnyConnect Secure Mobility Client 3.0.0629, but I'm not able to get the IPSec VPN works. Also, it has no option to use the previous of Cisco IPSec VPN client PCF files.

  Can someone point me in the right direction to get IPSec VPN AnyConnect 3.0 work?

  Thank you in advance!

  Hello

  Takes AnyConnect support IPSEC from version 3.0, but only in combination with IKEv2.

  There is no option to use a CPF file with it and the config should be pushed through a profile Anyconnect.

  More information on this:

  http://www.Cisco.com/en/us/docs/security/vpn_client/AnyConnect/anyconnect30/Administration/Guide/ac02asaconfig.html#wp1325361

  You should also change the ASA config so that it accepts negotiations IKE v2:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/vpn_ike.html#wp1144572

  Kind regards

  Nicolas

• Qosmio G40 - which driver can be used for remote control?

  Hello

  Which driver should I use for remote control?

  How to configure with the PC?

  Thank you very much.

  I assume that you need remote control manager.
  This tool is preinstalled on your Qosmio laptop?

• ASA 5510 VPN for remote access clients are asked to authenticate on box

  Don't know what's the matter, but my remote access users are invited to join the ASA before connecting to the tunnel. How can I disable this? Config is attached. Thank you all -

  For remote access connections, you can turn off the prompt xauth (user/pass) with the following:

  Tunnel ipsec-attributes group

  ISAKMP ikev1-user authentication no

  -heather

• alternatives to LogMeIn Pro for remote access?

  Greetings.  Currently, we have systems in the United States, Switzerland and the Mexico that I supported via remote access using LogMeIn Pro.  We paid for a subscription before free LMI Pro has been abandoned even to appreciate the characteristics of LMI Pro.  But as LMI has eliminated this free service, it seems their subscription rate more than doubled each year.  We currently need remote access to 3 Macs and 2 units of Windows (ew).

  Last year, we paid $174. for the annual subscription in support of these 5 systems.  I just checked on the price of renewal and it shows $349.00 for renewal.  This is getting too expensive!

  Last year, I invested in ARD to support my mother MacBook and the MacBook from an old friend, rather than pay LMI for a subscription in support of these systems.  ARD was a good alternative for these systems, but it is not a realistic alternative to remote systems for charity I help support.  Partly because of the PC, also because what it requires port forwarding in the router and finally because I have to be at my computer to use ARD to access those other systems.  LMI offers the possibility to access systems through an iOS app and can be used by other members of the team of charity, anywhere in the world everyone is physically located.  That's why we have maintained the LMI Pro subscriptions for a number of years.

  But with the perennial increase rate of LMI ridiculous (I think they can take their pricing of Obamacare), I'm on my eternal quest for an alternative to remote access.

  Can anyone offer advice?

  Thank you very much for your review,

  Dee Dee in Florida

  There are:

  -Apple Back to My Mac

  Set up and use Back to My Mac - Apple Support

  -Team Viewer free for non-commercial and paid for commercial use.

  -GoToMyPC, it also works with Mac

• NAR restriction for remote access clients

  Hello

  just a question how to limit access to users for some NAS servers remotely.

  We have an AAA ACS2.6 servers and several 3640 based NAS server for remote user access. Users are gathered in a group to the ACS.

  We have another group, called ISP. The user in this group can use the internet anywhere in the world, they must dial the local number of the given ISP NAS and all the NAS-you pass the authentication request to our CSA. So we can centrally manage direct RAS users and Internet users.

  The problem is that a user to a certain group can use the other dialin facility since all dialin appemps will be authenticated on the same server.

  How can I limit that an ISP group cannot use the SNS outside the company and that he can not numbering at our dedicated RAS server? And RAD regulars cannot use the internet (which is given to the users of the ISP)

  I applied filters in the ACS on the group settings, but could find no ducuments how configure it exactly. Any help appreciated,

  Kind regards

  Balázs

  Balázs,

  Thanks for sharing your experience. I'm sure that it would be useful for others. Yes, browser is a problem for any management software ;-)

  Thanks again,

  Renault

• Server ezvpn 887 router for remote access

  Hello.

  I'm having a problem with the implementation of remote access using easyvpn server on a router 887.  I followed the tutorials and also used Assistant cisco configuration professional easyvpn server to the configuration but still having a problem.

  I see, but Phase 1 finished, Phase 2 will fail with the following error...

  09:43:26.515 Oct 10: ISAKMP: (2003): check IPSec proposal 8

  09:43:26.515 Oct 10: ISAKMP: turn 1, ESP_AES

  09:43:26.515 Oct 10: ISAKMP: attributes of transformation:

  09:43:26.515 Oct 10: ISAKMP: authenticator is HMAC-SHA

  09:43:26.515 Oct 10: ISAKMP: key length is 128

  09:43:26.515 Oct 10: ISAKMP: program is 1 (Tunnel)

  09:43:26.515 Oct 10: ISAKMP: type of life in seconds

  09:43:26.515 Oct 10: ISAKMP: service life of SA (IPV) 0x0 0 x 20 0xC4 0x9B

  09:43:26.515 Oct 10: ISAKMP: (2003): atts are acceptable.

  09:43:26.515 Oct 10: IPSEC (validate_proposal_request): part #1 the proposal

  09:43:26.515 Oct 10: IPSEC (validate_proposal_request): part #1 of the proposal

  (Eng. msg key.) Local INCOMING = 88.xx.xxx.174:0, distance = 80.177.185.185:0,.

  local_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4),

  remote_proxy = 192.168.21.12/255.255.255.255/0/0 (type = 1),

  Protocol = ESP, transform = NONE (Tunnel),

  lifedur = 0 and 0kb in

  SPI = 0 x 0 (0), id_conn = 0, keysize = 128, flags = 0 x 0

  09:43:26.515 Oct 10: map_db_find_best found no corresponding card

  09:43:26.515 Oct 10: IPSEC (ipsec_process_proposal): proxy unsupported identities

  09:43:26.515 Oct 10: ISAKMP: (2003): IPSec policy invalidated proposal with error 32

  'Proxy unsupported identities' research indicates a NAT problem maybe, but I don't see where this would be.  In my view, the problem is elsewhere.

  I use the VPN Client 5.0.07.0440 and using transparent tunneling IPSec (on TCP/10000) that the client is located behind a firewall/NAT device.

  Does anyone know what may be the issue?  Attached full config.

  Hello Mick

  Before that, one more try. .

  Remote control the pfs as follows

  Profile of crypto ipsec RemoteAccess

  no set pfs group2

  Remove and add the virtual model crypto back

  type of interface virtual-Template1 tunnel

  No ipsec protection RemoteAccess tunnel profile

  Profile of tunnel RemoteAccess ipsec protection

  I hope this will solve your problem

  Henin,

• authentication 802. 1 x on cisco VPN for remote access

  I'm on dial-up VPN (mobile VPN) on cisco ASA5510, now, I want to authenticate remote users via Microsoft IAS (Radius Standard) service. However, I couldn't get through the via protocol PEAP authentication process, and it seems that it only supports PAP that isn't safe.

  Any suggestion on how to implement PEAP over VPN remote access?

  Thank you

  Hello

  Glance atv http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00806de37e.shtml

  It may be useful.

  Best regards.

  Massimiliano.

• How to configure VPN 3000 Concentrator for remote access

  I have inherited a VPN concentrator and want to configure it to provide remote access to my internal laboratory network when I'm traveling.  Private interface is configured as 192.168.1.240/24.  Public interface is configured as one of my public IP addresses.  I have a public IP pool on the back side of a cable modem Roadrunner.  I created a pool of addresses for clients such as 192.168.1.200 by 192.168.1.205.  I created all group configurations, group and user base.

  In the IP Routing tab, I see a default route pointing to my IP address of public gateway - the IP address of my box of roadrunner cable modem gateway.

  Since my VPN client, I am able to connect to the VPN concentrator.  I get an address from the pool and check the details of the tunnel under the statistics section shows IP address correct pool for the customer and the correct public IP address of my VPN reorga

  Jeff,

  According to statistics, it seems that the client sends traffic to the hub, but his answer not get back.

  We need check the hub settings itself.

  I need check the hub settings and that it is a GUI based device so I can't even ask to see the technology and the only option available is to WebEx.

  You're ok with webex, pls lemme session comfortable time id and e-mail to send the invitation, it takes no more time and we will carry it out

  Thank you

  Ankur

• Hyperion Financial Reporting of ports for remote access

  Hello
  Can I know what are the ports should I open to allow remote access to the server Hyperion Financial Reporting for reporting via Hyperion Financial Reporting Studio home pc?
  
  
  Thank you

  You could also have a read of http://john-goodwin.blogspot.co.uk/2013/02/financial-reporting-studio-firewall-fun.html

  See you soon

  John
  http://John-Goodwin.blogspot.com/

• How many group Supportepar ASA 5520 vpn for remote access

  Hello

  Howmany vpn group is supported on asa 5520 with configuraion vpn remote access.

  Concerning

  1 if nat-control is disabled and you do not have any other order NAT in your config file, you do not have it. Try to remove the existing "NAT 0" command and "clear xlate."

  2. you must ensure that your network inside know they can go by ASA to access remote vpn client IP. You have any device layer 3 behind the ASA that does the routing. If so, please verify that this is the routing table.

• How can I assign the static fixed IP for remote access VPN users

  Hi team,

  I have a requirement to assign a fixed static IP users VPN remote access in ASA, please help how I can achice this

  Thanks in advance
  Mikael

  username user1 attributes

  VPN-framed-ip-address 10.200.115.78 255.255.0.0

• The use of Teamviewer for remote access to another PC from a PC

  Hello

  I have TWO PC, but unfortunately two PC has the same IP I checked ipconfig.

  I called ISP regarding on the same IP between two PCs.

  Is it possible that a PC can access second tool PC remotely using the Teamviewer software, even if TWO PC IP addresses are the same now?

  Your comments will be appreciated.

  Thank you

  Hi Altman,

  TeamViewer is a third party software. For support on the use of this product go to TeamViewer Support Center.

  Note:   software use of third parties, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

• Can I use calls for remote access SOAP works on a SOAP server?

  Hello

  I used JavaScript and SOAP with "Acrobat ordinary' (e.g. Acroforms) to connect to a SOAP server, followed by Acrobat automatically set-up of functions I can call some JavaScript which, with the permission of SOAP, are relayed to the SOAP server for execution.  For example, a SOAP server that implements a function of temperature.  After doing the Net.SOAP.connect, my JavaScript magically accesses the Temperature() function, which is then executed remotely on the SOAP server with the SOAP protocol.

  My question is: with Livecycle Designer XFA forms and it is, I don't have the same ability to connect programmatically to a SOAP server and have configured automatically JavaScript functions I can call on the server?  What I've read, there are LC submit and Execute operations that interact (for example exchange data) with a SOAP server specified, but it is not clear that LC offers the possibility to end up with a set of functions that I can call from my JavaScript which are then performed on the SOAP server.

  
  In simpler terms: LiveCycle Designer has the ability to connect to a SOAP server and automatically configured the JavaScript functions I can call (which then get relayed to the SOAP server for execution, followed by the return of my program XFA data)?

  Thank you.

  
  Dave

  I used the same scenario in most of my forms... passing XML as file WSDL input and response using SOAP... Here is an example that might come to our rescue.

  function saveToDocumentum (wfname) {}

  SOAP.wireDump = false;

  var cWSURL = 'http://servername..» "com:" + "/services/" + wfname + "? wsdl"; //use this inspires wisely WSDLURL

  try {}
  var service = SOAP.connect (cWSURL);
  } catch (e)
  {
  App.Alert ("" + e);
  Returns a null value.
  }
  If (typeof service! = "object")
  {
  App.Alert ("could not connect on backwards to" + cWSURL);
  Returns a null value.
  }
  if(service.synchronousInvoke == undefined)
  {
  App.Alert ("could not obtain signature of operation synchronousInvoke");
  Returns a null value.
  }

  var sendXML = null;

  sendXML = xfa.data.saveXML ();
  startAt var = sendXML.indexOf (')<>
  endAt var = sendXML.indexOf (')
  sendXML = '"+ sendXML.substring (startAt, endAt + 13).
  sendXML = replaceAllSpecialChars (sendXML,"&","&");)
  xfa.host.messageBox(""+sendXML);

  var result = service.synchronousInvoke ({inxml: sendXML}); InXml is an input to the end WSDL variable

  Return resultthistime;

  App.Alert(""+result);
  var varma1 = result ['outxml'] //outxml is the name of the variable to the end WSDL and it is in XML format
  App.Alert(""+varma1);

  xfa.host.messageBox ("this request is stored in Documentum with success.", "Status", 3, 0);
  Return "success"; submitResult;

  }

  Good luck