Server ezvpn 887 router for remote access

Similar Questions

• Routing and remote access - on three subnetworked, two subnet unable to reach to the internet!

  Hello

  Good evening everyone.

  I had a problem in Routing and remote access on windows 2003 server.  This server is already configured as a file server, domain server, and application server. Also configured as a router (thanks to access routing & remote) to connect the three different networks with each other. If this server has three NICs installed and each separate NIC network cards represent.

  three different networks are - 192.42.160.0/24, 192.42.161.0/24, 192.42.162.0/24

  Three cards of the NETWORK adapter installed on the server as with the IP - next

  NIC - 1 = 192.42.160.220, Sub - 255.255.255.0, gateway - No.

  NIC - 2 = 192.42.161.220, Sub - 255.255.255.0, gateway - 192.161.220.112 (this ip address for internet access then 4 g router IP)

  -3 = 192.42.162.220, NETWORK cards, Sub - 255.255.255.0, gateway - No.

  Now the question is I can get Internet & (also scathing in router ip 192.42.161.112) one network i.e. - 192.42.161.0/24, BUT when I try to access the internet from another two network (192.42.160.0/24 & 192.42.162.0/24) I can not access and in addition can not ping to internet router ip - 192.42.161.112...

  So, how do I access the internet to another two network also?

  I was already the configuration of static routing for all three network but I wasn't always successful. I don't really know what exactly static routing this should be done in access routing & remote area so that all three network can reach to the internet?

  Here is the result of the current track...

  D:\Documents and Settings\Administrateur > route print

  IPv4 routing table
  ===========================================================================
  List of the interface
  0x1 ........................... MS TCP Loopback interface
  0x2... 00 30 05 8f ad 5 c... Broadcom NetXtreme Gigabit Ethernet - Mi Teefer2
  niport
  0 x 3... 0E 00 c4 f8 a7 0c... Network Intel(r) PRO/1000 GT Desktop Adapter - Teefer2 M
  iniport
  0 x 4... 0E 00 0c a7 c5 85... Intel (r) PRO/1000 GT Desktop Adapter #2 - Teefer
  2 miniport
  ===========================================================================
  ===========================================================================
  Active routes:
  Network Destination gateway metric Interface subnet mask
  0.0.0.0 0.0.0.0 192.42.161.112 192.42.161.220 1
  127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
  192.42.160.0 255.255.255.0 192.42.160.220 192.42.160.220 20
  192.42.160.220 255.255.255.255 127.0.0.1 127.0.0.1 20
  192.42.160.255 255.255.255.255 192.42.160.220 192.42.160.220 20
  192.42.161.0 255.255.255.0 192.42.161.220 192.42.161.220 20
  192.42.161.220 255.255.255.255 127.0.0.1 127.0.0.1 20
  192.42.161.255 255.255.255.255 192.42.161.220 192.42.161.220 20
  192.42.162.0 255.255.255.0 192.42.162.220 192.42.162.220 20
  192.42.162.220 255.255.255.255 127.0.0.1 127.0.0.1 20
  192.42.162.255 255.255.255.255 192.42.162.220 192.42.162.220 20
  224.0.0.0 240.0.0.0 192.42.160.220 192.42.160.220 20
  224.0.0.0 240.0.0.0 192.42.161.220 192.42.161.220 20
  224.0.0.0 240.0.0.0 192.42.162.220 192.42.162.220 20
  255.255.255.255 255.255.255.255 192.42.160.220 192.42.160.220 1
  255.255.255.255 255.255.255.255 192.42.161.220 192.42.161.220 1
  255.255.255.255 255.255.255.255 192.42.162.220 192.42.162.220 1
  Default gateway: 192.42.161.112
  ===========================================================================
  Persistent routes:
  None

  Sorry if I'm not able to explain properly. Please let me know if you have to explain more about it...

  Thank you all.

  Mahesh

  Hello Manu,

  Please post this question in the forums TechNet for Windows Server 2003. They will be able to guide you further.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home

• The Routing and remote access could not start, error 214500037 (0x80004005)

  My windows server 2003 r2, failed to start the Routing and remote access services. And in the event an observer log, it has error code
  Event ID: 7024, with service specific error 2147500037 (0x80004005)
  I tried to reset tcp/ip and replace ias.mdb and dnary.mdb by a new, but it did not work.

  Thank you

  Hi budhihartono,

  Since you are facing problems with windows server 2003 r2, it would be better suited in the Technet Windows forum. Please post your question in the following TechNet Windows server forum to improve assistance:

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• How to use ACS 5.2 to create a static ip address user for remote access VPN

  Hi all

  I have the problem. Please help me.

  Initially, I use ACS 4.2 to create the static ip address for VPN remote access user, it's easy, configuration simply to the user defined > address assignment IP Client > assign the static IP address, but when I use ACS 5.2 I don't ' t know how to do.

  I'm trying to add the IPv4 address attribute to the user to read "how to use 5.2 ACS", it says this:

  1Ajouter step to attribute a static IP address to the user attribute dictionary internal:

  Step 2select System Administration > Configuration > dictionaries > identity > internal users.

  Step 3click create.

  Static IP attribute by step 4Ajouter.

  5selectionnez users and identity of the stage stores > internal identity stores > users.

  6Click step create.

  Step 7Edit static IP attribute of the user.

  I just did, but this isn't a job. When I use EasyVPN client to connect to ASA 5520, user could the success of authentication but will not get the static IP I set up on internal users, so the tunnel put in place failed. I'm trying to configure a pool of IP on ASA for ACS users get the IP and customer EasyVPN allows you to connect with ASA, everything is OK, the user authenticates successed.but when I kill IP pool coufigurations and use the "add a static IP address to the user 'configurations, EzVPN are omitted.

  so, what should I do, if anyboby knows how to use ACS 5.2 to create a user for ip address static for remote access VPN, to say please.

  Wait for you answer, no question right or not, please answer, thank you.

  There are a few extra steps to ensure that the static address defined for the user is returned in the Access-Accept. See the instuctions in the two slides attached

• ASA 5510 VPN for remote access clients are asked to authenticate on box

  Don't know what's the matter, but my remote access users are invited to join the ASA before connecting to the tunnel. How can I disable this? Config is attached. Thank you all -

  For remote access connections, you can turn off the prompt xauth (user/pass) with the following:

  Tunnel ipsec-attributes group

  ISAKMP ikev1-user authentication no

  -heather

• AnyConnect 3.0 supports IPSec VPN for remote access?

  Hello world

  I've read about Cisco AnyConnect 3.0 issues that it supports IPSec VPN for remote access:

  http://www.Cisco.com/en/us/prod/collateral/vpndevc/ps6032/ps6094/ps6120/qa_c67-622477_ns1049_Networking_Solutions_Q_and_A.html

  I downloaded and installed the Client AnyConnect Secure Mobility Client 3.0.0629, but I'm not able to get the IPSec VPN works. Also, it has no option to use the previous of Cisco IPSec VPN client PCF files.

  Can someone point me in the right direction to get IPSec VPN AnyConnect 3.0 work?

  Thank you in advance!

  Hello

  Takes AnyConnect support IPSEC from version 3.0, but only in combination with IKEv2.

  There is no option to use a CPF file with it and the config should be pushed through a profile Anyconnect.

  More information on this:

  http://www.Cisco.com/en/us/docs/security/vpn_client/AnyConnect/anyconnect30/Administration/Guide/ac02asaconfig.html#wp1325361

  You should also change the ASA config so that it accepts negotiations IKE v2:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/vpn_ike.html#wp1144572

  Kind regards

  Nicolas

• Routing and remote access to the Server 2003

  I configured the remote access and routing service in my Server 2003 duly NAT enabled. All my clients are not in the field. All use internet and intranet connection using my proxy authentication provided by the administrator of the proxy server. I would like to restrict the clients except intranet connection. How to limit the customer?

  Post in the Windows Server Forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• The managed behind router switch remote access?

  What is the best way to access remotely to a switch behind a router?  I will use a switch SF300, and there is no server.

  For points of access (PA) behind a router, I give each a diffferent LAN address and port number.  In router I have forward TCP traffic with the single port/LAN IP.  Then using the port numbers with the address of the static router, the browser can remote access to the router or the attached AP.  But where do I put the managed switch LAN port number?  Assume default is port 80 and I would change to 8001 to switch #1; 8002 to switch #2; etc.  Could not find this info in the manual of configurtion.

  Hello

  At this point, I would recommend a call to the Cisco Small Business Centre at 1-866-606-1866 support so that action can be taken and your configuration can be reviewed.

  I have reproduced the concern here and I am able to remotely manage my switch SF300 with an RV082 as the router.

  My rule in the RV082 are as follows:

  Creating a custom topic UPnP service.  Create SF300 application name (it is a basic text field and can be any name), 8001 an external port and internal port 80.  I send to the address IP internal SF300 switch and click the check box.  From there on, I select Add to the list.  Once it appears in my list, I then click Save settings at the bottom of the page.

  Thank you!

  Dave

• alternatives to LogMeIn Pro for remote access?

  Greetings.  Currently, we have systems in the United States, Switzerland and the Mexico that I supported via remote access using LogMeIn Pro.  We paid for a subscription before free LMI Pro has been abandoned even to appreciate the characteristics of LMI Pro.  But as LMI has eliminated this free service, it seems their subscription rate more than doubled each year.  We currently need remote access to 3 Macs and 2 units of Windows (ew).

  Last year, we paid $174. for the annual subscription in support of these 5 systems.  I just checked on the price of renewal and it shows $349.00 for renewal.  This is getting too expensive!

  Last year, I invested in ARD to support my mother MacBook and the MacBook from an old friend, rather than pay LMI for a subscription in support of these systems.  ARD was a good alternative for these systems, but it is not a realistic alternative to remote systems for charity I help support.  Partly because of the PC, also because what it requires port forwarding in the router and finally because I have to be at my computer to use ARD to access those other systems.  LMI offers the possibility to access systems through an iOS app and can be used by other members of the team of charity, anywhere in the world everyone is physically located.  That's why we have maintained the LMI Pro subscriptions for a number of years.

  But with the perennial increase rate of LMI ridiculous (I think they can take their pricing of Obamacare), I'm on my eternal quest for an alternative to remote access.

  Can anyone offer advice?

  Thank you very much for your review,

  Dee Dee in Florida

  There are:

  -Apple Back to My Mac

  Set up and use Back to My Mac - Apple Support

  -Team Viewer free for non-commercial and paid for commercial use.

  -GoToMyPC, it also works with Mac

• NAR restriction for remote access clients

  Hello

  just a question how to limit access to users for some NAS servers remotely.

  We have an AAA ACS2.6 servers and several 3640 based NAS server for remote user access. Users are gathered in a group to the ACS.

  We have another group, called ISP. The user in this group can use the internet anywhere in the world, they must dial the local number of the given ISP NAS and all the NAS-you pass the authentication request to our CSA. So we can centrally manage direct RAS users and Internet users.

  The problem is that a user to a certain group can use the other dialin facility since all dialin appemps will be authenticated on the same server.

  How can I limit that an ISP group cannot use the SNS outside the company and that he can not numbering at our dedicated RAS server? And RAD regulars cannot use the internet (which is given to the users of the ISP)

  I applied filters in the ACS on the group settings, but could find no ducuments how configure it exactly. Any help appreciated,

  Kind regards

  Balázs

  Balázs,

  Thanks for sharing your experience. I'm sure that it would be useful for others. Yes, browser is a problem for any management software ;-)

  Thanks again,

  Renault

• How to configure VPN 3000 Concentrator for remote access

  I have inherited a VPN concentrator and want to configure it to provide remote access to my internal laboratory network when I'm traveling.  Private interface is configured as 192.168.1.240/24.  Public interface is configured as one of my public IP addresses.  I have a public IP pool on the back side of a cable modem Roadrunner.  I created a pool of addresses for clients such as 192.168.1.200 by 192.168.1.205.  I created all group configurations, group and user base.

  In the IP Routing tab, I see a default route pointing to my IP address of public gateway - the IP address of my box of roadrunner cable modem gateway.

  Since my VPN client, I am able to connect to the VPN concentrator.  I get an address from the pool and check the details of the tunnel under the statistics section shows IP address correct pool for the customer and the correct public IP address of my VPN reorga

  Jeff,

  According to statistics, it seems that the client sends traffic to the hub, but his answer not get back.

  We need check the hub settings itself.

  I need check the hub settings and that it is a GUI based device so I can't even ask to see the technology and the only option available is to WebEx.

  You're ok with webex, pls lemme session comfortable time id and e-mail to send the invitation, it takes no more time and we will carry it out

  Thank you

  Ankur

• Hyperion Financial Reporting of ports for remote access

  Hello
  Can I know what are the ports should I open to allow remote access to the server Hyperion Financial Reporting for reporting via Hyperion Financial Reporting Studio home pc?
  
  
  Thank you

  You could also have a read of http://john-goodwin.blogspot.co.uk/2013/02/financial-reporting-studio-firewall-fun.html

  See you soon

  John
  http://John-Goodwin.blogspot.com/

• How many group Supportepar ASA 5520 vpn for remote access

  Hello

  Howmany vpn group is supported on asa 5520 with configuraion vpn remote access.

  Concerning

  1 if nat-control is disabled and you do not have any other order NAT in your config file, you do not have it. Try to remove the existing "NAT 0" command and "clear xlate."

  2. you must ensure that your network inside know they can go by ASA to access remote vpn client IP. You have any device layer 3 behind the ASA that does the routing. If so, please verify that this is the routing table.

• authentication 802. 1 x on cisco VPN for remote access

  I'm on dial-up VPN (mobile VPN) on cisco ASA5510, now, I want to authenticate remote users via Microsoft IAS (Radius Standard) service. However, I couldn't get through the via protocol PEAP authentication process, and it seems that it only supports PAP that isn't safe.

  Any suggestion on how to implement PEAP over VPN remote access?

  Thank you

  Hello

  Glance atv http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00806de37e.shtml

  It may be useful.

  Best regards.

  Massimiliano.

• How can I assign the static fixed IP for remote access VPN users

  Hi team,

  I have a requirement to assign a fixed static IP users VPN remote access in ASA, please help how I can achice this

  Thanks in advance
  Mikael

  username user1 attributes

  VPN-framed-ip-address 10.200.115.78 255.255.0.0