ASA 5510 VPN for remote access clients are asked to authenticate on box

Similar Questions

• How many group Supportepar ASA 5520 vpn for remote access

  Hello

  Howmany vpn group is supported on asa 5520 with configuraion vpn remote access.

  Concerning

  1 if nat-control is disabled and you do not have any other order NAT in your config file, you do not have it. Try to remove the existing "NAT 0" command and "clear xlate."

  2. you must ensure that your network inside know they can go by ASA to access remote vpn client IP. You have any device layer 3 behind the ASA that does the routing. If so, please verify that this is the routing table.

• AnyConnect 3.0 supports IPSec VPN for remote access?

  Hello world

  I've read about Cisco AnyConnect 3.0 issues that it supports IPSec VPN for remote access:

  http://www.Cisco.com/en/us/prod/collateral/vpndevc/ps6032/ps6094/ps6120/qa_c67-622477_ns1049_Networking_Solutions_Q_and_A.html

  I downloaded and installed the Client AnyConnect Secure Mobility Client 3.0.0629, but I'm not able to get the IPSec VPN works. Also, it has no option to use the previous of Cisco IPSec VPN client PCF files.

  Can someone point me in the right direction to get IPSec VPN AnyConnect 3.0 work?

  Thank you in advance!

  Hello

  Takes AnyConnect support IPSEC from version 3.0, but only in combination with IKEv2.

  There is no option to use a CPF file with it and the config should be pushed through a profile Anyconnect.

  More information on this:

  http://www.Cisco.com/en/us/docs/security/vpn_client/AnyConnect/anyconnect30/Administration/Guide/ac02asaconfig.html#wp1325361

  You should also change the ASA config so that it accepts negotiations IKE v2:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/vpn_ike.html#wp1144572

  Kind regards

  Nicolas

• NAR restriction for remote access clients

  Hello

  just a question how to limit access to users for some NAS servers remotely.

  We have an AAA ACS2.6 servers and several 3640 based NAS server for remote user access. Users are gathered in a group to the ACS.

  We have another group, called ISP. The user in this group can use the internet anywhere in the world, they must dial the local number of the given ISP NAS and all the NAS-you pass the authentication request to our CSA. So we can centrally manage direct RAS users and Internet users.

  The problem is that a user to a certain group can use the other dialin facility since all dialin appemps will be authenticated on the same server.

  How can I limit that an ISP group cannot use the SNS outside the company and that he can not numbering at our dedicated RAS server? And RAD regulars cannot use the internet (which is given to the users of the ISP)

  I applied filters in the ACS on the group settings, but could find no ducuments how configure it exactly. Any help appreciated,

  Kind regards

  Balázs

  Balázs,

  Thanks for sharing your experience. I'm sure that it would be useful for others. Yes, browser is a problem for any management software ;-)

  Thanks again,

  Renault

• authentication 802. 1 x on cisco VPN for remote access

  I'm on dial-up VPN (mobile VPN) on cisco ASA5510, now, I want to authenticate remote users via Microsoft IAS (Radius Standard) service. However, I couldn't get through the via protocol PEAP authentication process, and it seems that it only supports PAP that isn't safe.

  Any suggestion on how to implement PEAP over VPN remote access?

  Thank you

  Hello

  Glance atv http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00806de37e.shtml

  It may be useful.

  Best regards.

  Massimiliano.

• ASA 5510 - VPN for DMZ with static rule?

  I have a 5510 ASA with a number of virtual private networks to other sites, allowing the traffic to and from the Interior of the networks.

  I need to establish a VPN rule to another site, but they have very little access to resources on my local network.  Because I am not in control of the SAA on this end permanently, I need to control that access on my 5510.

  (the following is not my real IP, but I use them for this example)

  My network: 10.100.1.x

  My DMZ: 192.168.1.x

  Internal network of other sites: 172.16.1.x

  I wanted to try to create a VPN between the site and the specific address of DMZ on my side and then allow access to internal addresses using static rules.  I decided to use a static rule to enable http access to a specific server (for example):

  static (inside, dmz) 192.168.1.200 tcp 80 10.100.1.200 80

  I need allow traffic here:

  access-list permits DMZ_IN tcp host 172.16.1.10 host 192.168.1.200 eq 80

  Access-group interface dmz DMZ_IN

  And of course, rules of access list which allow traffic that I can apply to the VPN:

  toSite host 192.168.1.200 ip access list permit 172.16.1.10

  And I don't want that traffic THAT NAT had between my DMZ and the other site:

  nonatDMZ of the host 192.168.1.200 ip access list permit 172.16.1.10

  NAT (dmz) 0-list of access nonatDMZ

  NAT (dmz) 1 0.0.0.0 0.0.0.0

  And, of course, the corresponding rules on their ASA must be in place, allowing traffic to 192.168.1.200, not NAT it.

  Everything is in place, but 172.16.1.10 to 192.168.1.200 http traffic never reaches 10.100.1.200.  I know the following:

  1. the VPN is configured correctly.  If I add rules allowing traffic to (and from) 172.16.1.10 and 10.100.1.200 directly, they work.

  2 packet trace shows me that traffic is allowed.

  3. the works of static rule: to access the 192.168.1.200:80 of another host on the same interface, DMZ, which brings me to 10.100.1.200:80

  4. in the process of running a sniffer package on 10.100.1.200 shows 172.16.1.10 traffic does not reach it.

  So I'm banging my head against the wall here.  I'm sure it's something simple I'm missing.  Anything else I need to check?  Should I go about this a different way?

  Thank you.

  What you are trying to reach is not supported. You cannot configure NATing between the inside and the demilitarized zone interfaces while your VPN connection is from the external interface. The static NAT (inside the dmz) that you have configured will only work if the connection is initiated from the inside towards the demilitarized zone and vice versa.

  I think that what you are trying to reach is only allowing access on TCP/80 to10.100.1.200 for the VPN tunnel.

  You must configure your option 1:

  1. the VPN is configured correctly.  If I add rules allowing traffic to (and from) 172.16.1.10 and 10.100.1.200 directly, they work.

  You can configure vpn-filter to limit the traffic to the only TCP/80, and he attributed to group policy that you have assigned to this particular tunnel group then.

  Example:

  web access list - allow permit tcp host 172.16.1.10 host 10.100.1.200 eq 80

  internal group-policy-strategy web

  attribute group web-strategy strategy

  value of VPN-filter web - allows

  global-tunnel-group attributes

  Group Policy - by default-web-policy

  Here is an example configuration for your reference:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808c9a87.shtml

  Hope that helps.

• How to use ACS 5.2 to create a static ip address user for remote access VPN

  Hi all

  I have the problem. Please help me.

  Initially, I use ACS 4.2 to create the static ip address for VPN remote access user, it's easy, configuration simply to the user defined > address assignment IP Client > assign the static IP address, but when I use ACS 5.2 I don't ' t know how to do.

  I'm trying to add the IPv4 address attribute to the user to read "how to use 5.2 ACS", it says this:

  1Ajouter step to attribute a static IP address to the user attribute dictionary internal:

  Step 2select System Administration > Configuration > dictionaries > identity > internal users.

  Step 3click create.

  Static IP attribute by step 4Ajouter.

  5selectionnez users and identity of the stage stores > internal identity stores > users.

  6Click step create.

  Step 7Edit static IP attribute of the user.

  I just did, but this isn't a job. When I use EasyVPN client to connect to ASA 5520, user could the success of authentication but will not get the static IP I set up on internal users, so the tunnel put in place failed. I'm trying to configure a pool of IP on ASA for ACS users get the IP and customer EasyVPN allows you to connect with ASA, everything is OK, the user authenticates successed.but when I kill IP pool coufigurations and use the "add a static IP address to the user 'configurations, EzVPN are omitted.

  so, what should I do, if anyboby knows how to use ACS 5.2 to create a user for ip address static for remote access VPN, to say please.

  Wait for you answer, no question right or not, please answer, thank you.

  There are a few extra steps to ensure that the static address defined for the user is returned in the Access-Accept. See the instuctions in the two slides attached

• ASA 5520 - VPN using LDAP access control

  I'm setting up an ASA 5520 for VPN access.  Authorization & authentication using an LDAP server.  I have successfully configured tunnel, and I can access internal resources.  What I want to do now is to limit access to a specific ad group membership.  In the absence of this belonging to a group, a user cannot access the VPN.

  My VPN client software testing is Cisco Systems VPN Client 5.0.05.0290 Version.  The Group authentication is configured in a connection entry that identifies the Group of Tunnel. I think I wrote that correctly.

  The Version of the software on the SAA is 8.3 (1).

  My current challenge is getting the VPN to stop letting each request for access through little matter belonging to a group.  I found the thread below to be significantly useful, but there is obviously something which is not entirely mesh with my situation.

  https://supportforums.Cisco.com/message/3232649#3232649

  Thanking all in advance for everything offered thoughts and advice.

  Configuration (AAA LDAP, group policy and group of tunnel) is below.

  AAA-Server LDAP protocol ldap
  AAA-Server LDAP (inside) host x.x.y.12
  Server-port 636
  LDAP-base-dn dc = domain, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn cn = svcacct, or = svcac, or = users, or = svcad, dc = domain, dc = com
  enable LDAP over ssl
  microsoft server type
  LDAP-attribute-map LDAP_MAP
  AAA-Server LDAP (inside) host x.x.y.10
  Server-port 636
  LDAP-base-dn dc = domain, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn cn = svcacct, or = svcac, or = users, or = svcad, dc = domain, dc = com
  enable LDAP over ssl
  LDAP-attribute-map LDAP_MAP
  AAA-Server LDAP (inside) host x.x.y.11
  Server-port 636
  LDAP-base-dn dc = domain, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn cn = svcacct, or = svcac, or = users, or = svcad, dc = domain, dc = com
  enable LDAP over ssl
  microsoft server type
  LDAP-attribute-map LDAP_MAP

  AAA-Server LDAP (inside) host x.x.y.10
  Server-port 636
  LDAP-base-dn dc = domain, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn cn = svcacct, or = svcac, or = users, or = svcad, dc = domain, dc = com
  enable LDAP over ssl
  LDAP-attribute-map LDAP_MAP
  AAA-Server LDAP (inside) host x.x.y.11
  Server-port 636
  LDAP-base-dn dc = domain, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn cn = svcacct, or = svcac, or = users, or = svcad, dc = domain, dc = com
  enable LDAP over ssl
  microsoft server type
  LDAP-attribute-map LDAP_MAP
  !
  internal group NOACCESS strategy
  NOACCESS group policy attributes
  VPN - concurrent connections 0
  Protocol-tunnel-VPN IPSec webvpn
  address pools no
  attributes of Group Policy DfltGrpPolicy
  VPN - 10 concurrent connections
  Protocol-tunnel-VPN IPSec webvpn
  enable IPSec-udp
  vpn group policy - pro internal
  vpn - pro group policy attributes
  value x.x.y.17 x.x.y.27 WINS server
  Server DNS value x.x.y.19 x.x.y.29
  VPN - 50 simultaneous connections
  Protocol-tunnel-VPN IPSec svc
  group-lock value vpn - pro
  field default value domain.com
  value of address ip-vpn-pro pools
  WebVPN
  client of dpd-interval SVC no
  dpd-interval SVC 1800 bridge
  !

  attributes global-tunnel-group DefaultRAGroup
  LDAP authentication group-server
  LDAP authorization-server-group
  Group Policy - by default-vpn-pro
  authorization required
  type group tunnel vpn - pro remote access
  attributes global-tunnel-group-vpn - pro
  LDAP authentication group-server
  Group-server-authentication (LDAP outside)
  LDAP authorization-server-group
  Group Policy - by default-vpn-pro
  band-Kingdom
  password-management
  band-band
  authorization required
  type tunnel-group NOACCESSGROUP remote access
  attributes global-tunnel-group NOACCESSGROUP
  LDAP authentication group-server
  NOACCESS by default-group-policy

  Hello

  The configuration of what you are looking for is a feature called DAP (Dynamic Access Policy)

  The following link will explain how to set up the same.

  http://www.ciscosystems.com/en/us/products/ps6120/products_white_paper09186a00809fcf38.shtml

  I hope this helps.

  Kind regards

  Anisha

  P.S.: Please mark this thread as answered if you feel that your query is resolved. Note the useful messages.

• Crossed between the remote access client to a remote site at a Site in Tunnel

  Here's the scenario: users access remote vpn in ASA5510 with the tunneling split. The ASA has a tunnel from one site to another site. Vpn remote access users must be able to come and then go back devices on this tunnel from site to site. Is it still possible? Most of what I see on crossed is internet access when not to use the tunneling split.

  Thank you!

  You can do this job.  First of all, you should make sure that the command "permit same-security-traffic intra-interface" is configured.  You will then want to update your remote access ACL to include accessible subnets via the split tunneling L2L tunnel.  In this way, customers will receive a static route routing traffic through the tunnel for remote access.  The ACL crypto for the L2L tunnel shall include either a specific or analytical entry to the pool of the VPN client to destination subnets.  The corresponding crypto ACL on the far side of the tunnel L2L will need to be updated with a mirror reverse configuration of hub.  Finally, if you have configured on the NAT ASA, you will need to include a rule of exemption for the pool of VPN client-> remote subnet traffic flow.

• Cisco ASA 5510 VPN Site to Site with Sonicwall

  I am trying to configure a tunnel between a Cisco ASA 5510 VPN (Version 8.2 (2)) and TZ200 Sonicwall. I rose tunnel and go and I am able to ping the internal IP address of Cisco ASA of the Sonicwall LAN but nothing work. When I try to ping a host behind the Cisco ASA of the Sonicwall LAN I get the following message "rules asymmetrical NAT matched for flows forward and backward; Connection for tcp src outside:10.20.10.x/xxxx dst inside:10.20.2.x/xxxx refused due to failure of reverse path of NAT"on the SAA

  Googling the error above shows the problems with version 8.3 or later that resembled the nat commands have been changed SAA, train is still on 8.2 but I another common question does not add an exemption of NAT I have double-triple checked that I did add an exception rule of NAT of the hosts on the network from cisco for the guests of the Sonicwall network. Looks like I hit a road block so any help would be appreciated. Thank you

  Here are a few excertps of the config file (10.20.2.0 behind the cisco) and 10.20.10.0 behind the sonicwall

  NAT (inside) 0 access-list sheep

  ..

  IP 10.20.2.0 allow Access-list extended sheep 255.255.255.0 10.20.10.0 255.255.255.0

  access extensive list ip 10.20.2.0 outside_1_cryptomap allow 255.255.255.0 10.20.10.0 255.255.255.0

  ..

  card crypto outside_map 1 match address outside_1_cryptomap

  card crypto outside_map 1 set counterpart x.x.x.x

  card crypto outside_map 1 set of transformation-ESP-3DES-SHA

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  ..

  crypto ISAKMP allow outside

  crypto ISAKMP policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  lifetime 28800

  ..

  internal SiteToSitePolicy group strategy

  attributes of Group Policy SiteToSitePolicy

  VPN-idle-timeout no

  Protocol-tunnel-VPN IPSec

  Split-tunnel-network-list no

  ..

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group x.x.x.x General attributes

  Group Policy - by default-SiteToSitePolicy

  tunnel-group ipsec-attributes x.x.x.x

  pre-shared key *.

  ..

  Added some excerpts from the configuration file

  Hello Manjitriat,

  Okay, detected IPSEC parody is normal, that means you are trying to send unencrypted on a line of encrypted packets.

  Now, if you see on the plotter of package that traffic will hollow the VPN channel all its fine in your site.

  Now the packet tracer must be something like this:

  entrance to Packet-trace inside private_ip_lan destination_private_ip_lan 1025 tcp 80

  Please provide us with the result of the following instructions after you run the packet tracer.

  See the crypto Isakamp SA

  See the crypto Ipsec SA

  Kind regards

  Julio

• Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

  I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

  Thank you

  interface Ethernet0/0

  Speed 100

  full duplex

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.240

  !

  interface Ethernet0/1

  Speed 100

  full duplex

  nameif inside

  security-level 100

  IP 10.88.10.254 255.255.255.0

  !

  interface Management0/0

  Shutdown

  nameif management

  security-level 0

  no ip address

  !

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  network of the PAT_to_Outside_ClassA object

  10.88.0.0 subnet 255.255.0.0

  network of the PAT_to_Outside_ClassB object

  subnet 172.16.0.0 255.240.0.0

  network of the PAT_to_Outside_ClassC object

  Subnet 192.168.0.0 255.255.240.0

  network of the LocalNetwork object

  10.88.0.0 subnet 255.255.0.0

  network of the RemoteNetwork1 object

  Subnet 192.168.0.0 255.255.0.0

  network of the RemoteNetwork2 object

  172.16.10.0 subnet 255.255.255.0

  network of the RemoteNetwork3 object

  10.86.0.0 subnet 255.255.0.0

  network of the RemoteNetwork4 object

  10.250.1.0 subnet 255.255.255.0

  network of the NatExempt object

  10.88.10.0 subnet 255.255.255.0

  the Site_to_SiteVPN1 object-group network

  object-network 192.168.4.0 255.255.254.0

  object-network 172.16.10.0 255.255.255.0

  object-network 10.0.0.0 255.0.0.0

  outside_access_in deny ip extended access list a whole

  inside_access_in of access allowed any ip an extended list

  11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

  outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

  mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

  NAT static NatExempt NatExempt of the source (indoor, outdoor)

  NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

  NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

  !

  network of the PAT_to_Outside_ClassA object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassB object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassC object

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_access_in in interface outside

  inside_access_in access to the interface inside group

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  dynamic-access-policy-registration DfltAccessPolicy

  Sysopt connection timewait

  Service resetoutside

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto-map dynamic dynmap 10 set pfs

  Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

  life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

  Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

  Crypto-map dynamic dynmap 10 the value reverse-road

  card crypto mymap 1 match address outside_1_cryptomap

  card crypto mymap 1 set counterpart x.x.x.x

  card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

  card crypto mymap 86400 seconds, 1 lifetime of security association set

  map mymap 1 set security-association life crypto kilobytes 4608000

  map mymap 100-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  crypto isakmp identity address

  Crypto isakmp nat-traversal 30

  Crypto ikev1 allow outside

  IKEv1 crypto ipsec-over-tcp port 10000

  IKEv1 crypto policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 50

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  preshared authentication

  aes-256 encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  Console timeout 0

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal BACKDOORVPN group policy

  BACKDOORVPN group policy attributes

  value of VPN-filter 11

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelall

  BH.UK value by default-field

  type tunnel-group BACKDOORVPN remote access

  attributes global-tunnel-group BACKDOORVPN

  address pool Admin_Pool

  Group Policy - by default-BACKDOORVPN

  IPSec-attributes tunnel-group BACKDOORVPN

  IKEv1 pre-shared-key *.

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group ipsec-attributes x.x.x.x

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  Excellent.

  Evaluate the useful ticket.

  Thank you

  Rizwan James

• ASA 5510 vpn remote access - must now be added vpn site-to-site.

  We currently have a configuration of remote access vpn and all this hard work.

  I need to configure a vpn lan lan 2 now.

  Can someone point me to the documentation on that? I used the command line to add a site to site and wrong on it and disconnected me when I applied the crypto map to the external interface. Do I need another card encryption or should I use my existing?

  Shannon,

  Please see the below URL for more configuration information. Even if that configuration is dynamic to static IPSEC, you can use the concept to build the Tunnel L2L with static IP.

  http://www.Cisco.com/en/us/partner/products/ps6120/products_configuration_example09186a00805733df.shtml

  Let me know if it helps.

  Kind regards

  Arul

  * Please note all useful messages *.

• Option of DAP for the verification of the registry for remote access VPN Anyconnect v 3.0 + users

  Hi all

  I'm trying to assign the attribute DAP users VPN (Anyconnect 3.0 +) who fulfil certain conditions of registry. When setting up political DAP, while selecting the condition of the register, it is in error as "secure desktop cisco (CSD) is not enabled, CSD should be enabled to configure the registry endpoint attribute. But as I link percevied, to check the attribute registry "scan host' which is integrated in the module anyconnect 3.0 will be charged. So why he asks me to activate the CSD? CSD is really necessary to verify the registry attribute even if we use anyconenct 3.0 +? Any pointer

  The end of the ASA must be activated and more bits based on AnyConnect.

  Notes elsewhere in the link you quoted, it is said ' host Scan automatically identifies the operating systems and service packs on any remote device establishing a clientless SSL VPN and AnyConnect Cisco client session and when the host Scan/CSD or CSD is activated on the SAA. " (emphasis added).

  FYI Cisco is to denigrate these features over time for the Posture of scanning at the ISE in conjunction with the new posture AnyConnect 4.0 module.

• How can I dedicate a single ip address to a client on asa 5510 vpn

  Hi all

  My question is...

  How can I dedicate a unique to a single customer VPN VPN NAT ip? I don't want this ip address used by another vpn client...

  I got an ASA 5510 with a

  DHCP pool.

  5.0 Cisco vpn client

  Thank you

  You are welcome. Please note the answers and mark your question answered to increase the value of the instance.

• How to configure VPN 3000 Concentrator for remote access

  I have inherited a VPN concentrator and want to configure it to provide remote access to my internal laboratory network when I'm traveling.  Private interface is configured as 192.168.1.240/24.  Public interface is configured as one of my public IP addresses.  I have a public IP pool on the back side of a cable modem Roadrunner.  I created a pool of addresses for clients such as 192.168.1.200 by 192.168.1.205.  I created all group configurations, group and user base.

  In the IP Routing tab, I see a default route pointing to my IP address of public gateway - the IP address of my box of roadrunner cable modem gateway.

  Since my VPN client, I am able to connect to the VPN concentrator.  I get an address from the pool and check the details of the tunnel under the statistics section shows IP address correct pool for the customer and the correct public IP address of my VPN reorga

  Jeff,

  According to statistics, it seems that the client sends traffic to the hub, but his answer not get back.

  We need check the hub settings itself.

  I need check the hub settings and that it is a GUI based device so I can't even ask to see the technology and the only option available is to WebEx.

  You're ok with webex, pls lemme session comfortable time id and e-mail to send the invitation, it takes no more time and we will carry it out

  Thank you

  Ankur