Virtual disk 1 gradient

Similar Questions

• Reference Dell MD3220 virtual disk - hot spare in use

  We have a Dell MD3220.  one of the hard drives was taken out by an end-user trying to exchange a defective disc. Then after that the good player has replaced the old drive was placed back into the appropriate slot. Now we have a hot spare (enclosure 0, slot 23) in lieu of an another hot spare (attachment 2, slot 22). The hot spare that is subbed for has been replaced by two new hard drives now and the hot spare in use has still not disappeared. any suggestions on what to do next?

  Virtual disk - hot spare in use

  Storage array: MD3220
  Disk group: 2
    Physical disk failure in the: attachment 2, slot 22
       Action (deletion) enabled service:  NO. 
         LED of action on service component:  NO.
    Replaced with a physical disk to: enclosure 0, slot 23
    Virtual disks: 3
       RAID level: 5
       Status:  Gradient

  Hello, GalaxyTechService.

  It is perhaps not as complicated as it may seem, in fact. There is a wizard that you can use to return the disk to the raid set. Right-click the affected virtual disk and select 'Replace physical disk' and use the wizard that opens.

  In the upper area will be "missing disks", and in the lower field will be options available to replace them.

  Then just follow the steps.

  Let me know how it goes.

• How to install Firefox 7 on a virtual disk in Windows 7?

  Firefox automatically installs in my program files and won't let me change that. I have a permanent virtual disk. I think that Firefox would go faster if I installed it on the ram disk.

  That will probably not noticeable different because Firefox loads the files of program in memory after loading and the profile folder with all the personal data is located elsewhere.
  
  It is usually written causing the more delays, especially if anti-virus software checks each entry.

  See the Firefox profile folder:

  • http://KB.mozillazine.org/Profile_folder_-_Firefox
  • Help > troubleshooting information > profile directory: opens showing the file

• Increase the size of the virtual disk.

  I just installed Windows virtual PC on Windows 7 64 bit and I try to install a program of 6 GB.  He said that there is not enough memory.
  The size of the virtual disk in less than 2 GB and I can't find any way to increase this size.  I tried to create a second virtual disk with more memory, but the same error comes back.  Is there a way I can increase the size of the primary virtual disk?

  Post here http://social.answers.microsoft.com/Forums/en-US/w7install/threads or here http://social.answers.microsoft.com/Forums/en-US/w7programs/threads instead.

• Acer Aspire V5 - 572G windows update, net and virtual disk problems.

  So I installed w7 x 64 ultimate on my laptop and notiiced windows update does not work. It shows that he can not connet to the server. After trying to fix it I discovered that I need to install net framework, which I tried, but he also failed because when I download the framework and before I press on install it shows me how much to download and it is 0. After I press on install it loads a little and it is said that he was not successful. Also tried to download some programs, such as driverpack, drivers search for and he found this lack gcdbusdevice and dcbusdevice im. When I tried downlaoding them, they seem not to exist. And when I try to install daemon tools or some simillar programs, it will fail to install, or fails to create a virtual disk, and after that the laptop can not stop lights. I have to use the restore point, and then he turns then on.

  So yes, some advice or help would be nice, thank you.

  Please see this link:
  Installation of a different operating system

  There are no drivers Windows 7 for the V5 - 572G on our page drivers.

  We don't support Windows 7 on this model.

• new Pavilion dv5 laptop Virtual Disk Service restarts every minute

  New journal of events system dv5 - 1007ca is filled with entries saying the virtual disk Service stops, restarts 1 minute later, stops after 2 seconds, then resumes at new 1 minute later.   4 inputs each minute.

  I went back to the store and found the same thing is happening on all the dv5 on screen, as well as HP tx tablets.

  The deactivation of the service is not a solution because then you can't get in the Disk Manager, more I do not know what else.

  Everyone has noticed this?   or can suggest how to stop this behavior?

  Looks like it's all new dv5, not just mine.

  Thank you

  Ok thank you.  Start in safe mode led me to the solution.

• How can I remove a virtual disk partition?

  Well, basically, I was using the program - Ramdisk, and it takes little memory your just RAM and transforms a partition you can store things in, or use it as a hard drive. But, now, I think he's using for many and I would remove it. I used 400 MB of ram, so now it is used. I went to computer management, went to the partition and delete the volume. Now, he says: 5 - base 400 MB drive online, but on the side, where it shows the volume actually score or what ever, it says 400 MB not allocated.

  So now I have 400 MB of ram m unallocated, and I'm trying to find a way to get it back in my ram used! Any help would be greatly please

  You would need to reverse the process used to create the virtual disk - uninstall the software used to create, or reverse the settings that you have invoked in Windows to create, as the case may be.  Just delete the disk partition RAM does not remove it from memory.

• Reference Dell HDS - recommended VMware virtual disk - drives provided - basic and dynamic thin and thick.

  Can someone point me to the literature on best practices for guest disc formats?

  I know all the Compellent thin-provisions. However, in VMware 5.5, when you set up a virtual disk in the comments you have several choices:

  • Lazy provisioned to zero thickness
  • Eager provisioned to zero thickness
  • Provision of thin

  And then, at the level of the OS, you have the choice of:

  • Base
  • Dynamics

  I would like a pointer to the technical document explaining the advantages/disadvantages of each choice and recommended best practices.

  Kind regards

  Kath

  I would like to either thin or thick lazy to zero.  The two will take the same amount of data on the HDS.  The main decision is where you want to manage your storage space?  If dilute you on thin you need to make sure that you make no provision in both places.  If you have thick lazy to zero, then you can only on commissioning on one side.

  Say that I always thin on thin.  Recovery of the space at the level of the virtual computer is not officially supported immediately, but maybe someday.

  In a virtualized environment, always keep it simple.  There is no dynamic performance with virtualization

• Virtual disk expansion

  I've added four new hard drives at 8 on my ax100 and configured ' DISK POOL 1, include 11 records. A drive is configured as a hot spare. Then, I have expanded the "Virtual Disk 1' to include all the"POOL1 DISC' again. I was expecting the SAN will appear as a 6 to drive in Win2003. However, it proved that I need to format the 4 additional disks and set up as a new partition. I need a shared 6 to disk, not two separate 4TB and shared 2 TB drives. I plugged a different server in the same San using the switch, but it also shows the SAN as two separate partitions.

  Is there an operation that is not destructive to consolidate all readers, both old and newly added, in a huge partition/drive and see it as such in Win2003? It would be difficult to make two backups one 6 to SAN, destroy the virtual disk, recreate a large drive virtual and end of restoration. Help, please. Thank you.

  
  

• Utility RAIDCFG to slow initialize virtual disks

  I use RAIDCFG. EXE from DTK to configure a Raid of H700 on a R910 controller.

  I would like to start slow initialization of a virtual disk. Documentation, the command is:

  raidcfg - vd - c = X - vd = Y - ac = sli

  I get a message of successful immediately command.

  How do I know what the State of the initialization?

  Thanks for any help.

  For more information on init, slow and fast, please visit NOTE from the ADMIN: broken link has been removed from this post by Dell >

• Problem creating virtual disk MD3600i

  I add a MD3600i (with extension MD1200) to a Cluster of servers Windows 2012 new file.  I have connected and configured to the point table to create virtual disks.  When I try to create a disc, the 'Work' spinner appears, then disappears almost instantly.  The wizard never loads.

  -J' tried MDSM from versions of resource disc, 4, 5 and 6 - no change.

  -J' removed and added the table several times.

  -J' updated the firmware newest controller.

  -J' tried both In-Band and Out-of-Band management connections.

  -J' tried with two pools and groups.

  -Out-of-band management stations have been Windows 7 and 8.1

  When running create it a Wizard of the pool, I can create virtual disks even size at the end of the process, but I can't create the readers in the free space remaining (more than enough available for a player)...  I need to be able to create readers as needed, please help!

  I spoke with Dell Support, and the solution was to delete and re-create the host in MDSM.

• MD3000 cannot change virtual disk ownership / preffered path - ERROR 29

  Current configuration

  PowerVault MD3000 (deleted by the moderator) - attached to two servers PowerEdge R610 using Dell SAS 5/e card in each r610. The R610s act as a host ESX VMWare ESXi 5.5.0

  We have created multiple LUNS on the storage array and noticed that traffice all happening through a RAID controller or another module (and it seems to me not change without prompting when you look at the storage Bay). I turned off a two different virtual machines to try to change the path and had an error with a certain delay - I stuck this error below. I also tried to redistribute virtual disks tab the MDSM software nothing works support.

  By reading, it seems that the LUN should be attributed to a particular raid controller before all I / 0, but I still feel like're missing us something as to why we cannot distribute the traffic properly.

  According to some records for a MD3200 -.

  "If the host has a path of data unique to the MD, the virtual disk storage array.
  must be owned by the controller to which the host is connected.
  That's what we're trying to accomplish. I don't know if the hosts are to be physically detached from the SAN, or if there is a bit of software to fail us.
  Thank you in advance! If I failed to provide all the details, please let me know and I'll try to gather the information.
  Here's the error output:

  OPERATING ENVIRONMENT DATA

  Name of the client system: FLMGMT01
  Client OS: Windows Server 2008 R2

  Application version: 03.35.G6.88
  Storage management of version table: 03.35.G6.88
  Name of storage array: VAB-NAS-01
  Firmware version: 07.35.39.64
  Management class: devmgr.v1035api01.Manager

  **************************************************

  DATA ERROR

  Command sent to the RAID controller module to the location: 0
  Host name: 192.168.19.233
  IP address: 192.168.19.233

  Return code: error 29 - this operation cannot complete because there was a failure of authentication of security on a parameter in the command sent to the RAID controller module.

  Try the operation again. If this message persists, contact your Technical Support representative.
  Operation when the error occurred: PROC_assignVolumeOwnership
  Timestamp: August 25, 2014 16:18:59

  DATA BATTERY

  devmgr.v1035api01.Sam.JAL.ManagementOperationFailedException:
  at devmgr.v1035api01.sam.jal.SYMbolClient.dispatchOperation (unknown Source)
  at devmgr.v1035api01.sam.jal.StorageArrayFacade.issueCommand (unknown Source)
  at devmgr.v1035api01.sam.jal.StorageArrayFacade.sendCommandCommon (unknown Source)
  at devmgr.v1035api01.sam.jal.StorageArrayFacade.sendCommand (unknown Source)
  at devmgr.v1035api01.sam.jal.StorageArrayFacade.assignVolumeOwnership (unknown Source)
  at devmgr.v1035api01.sam.configuration.controller.ChangeControllerOwnershipDialogPanel.performCommitAction (unknown Source)
  to devmgr.v1035api01.shared.wizard.DialogPanel$ NotifyBackgroundTaskAdapter.performOp (unknown Source)
  at devmgr.v1035api01.shared.AbstractTaskAdapter.run (unknown Source)

  THREAD DATA

  Thread [reference Manager 10, System]
  Thread [finalizer, 8, System]
  Thread [dispatcher Signal, 9, System]
  Thread [attach auditor, 5, System]
  Thread [Java2D grinder, 10, System]
  Thread [TimerQueue, 5, System]
  Thread [Swing-Shell, 6, System]
  Thread [AWT-closure, 5, main]
  Thread [AWT-Windows, 6, main]
  Thread [EventQueueMonitor-ComponentEvtDispatch, 5, main]
  Thread [Thread-3, 5, main]
  Thread [AWT-EventQueue-0, 6, main]
  Thread [DestroyJavaVM, 5, main]
  Thread [SwingWorker-pool-2-wire-1, 5, main]
  Thread [ChangeDetector, 6, main]
  Thread [PreferenceStoreChangeDetector, 6, main]
  Thread [LogMsgThread, 6, main]
  Thread [Np_Link_Monitor0, 6, main]
  Thread [DMVGarbageCollectorThread, 6, main]
  Thread [RecoveryProfile-27, 6, main]
  Thread [NEA-28, 6, main]
  Thread [RecoveryProfile-30, 6, main]
  Thread [NEA-31, 6, main]
  Thread [Timer 0, 6, main]
  Thread [RecoveryProfile-35, 6, main]
  Thread [NEA-36, 6, main]
  Thread [RecoveryProfile-38, 6, main]
  Thread [NEA-39, 6, main]
  Thread [Timer 1, 6, main]
  Thread [Timer 2, 6, main]
  Thread [Timer-3 6, main]

  
  Thread [RecoveryProfile-48, 6, main]
  Thread [NEA-49, 6, main]
  Thread [Timer-4 6, main]
  Thread [RecoveryProfile-53, 6, main]
  Thread [NEA-54, 6, main]
  Thread [Timer-5 6, main]
  Thread [SwingWorker-pool-2-wire-2, 5, main]
  Thread [RecoveryProfile-69, 6, main]
  Thread [NEA-70, 6, main]
  Thread [Timer-14, 6, main]
  Thread [Timer-91, 6, main]
  Thread [host 2.3, principal of the Image]

  Hello MrRedPants,

  Since you are using a configuration not redundant you will have problems trying to modify the paths between the controllers since the two hosts have only a single connection to the MD3000.  What you could do if possible is to get 2 more SAS cables & connect ports second on the MD to RAID opposite that the host is currently connected to.

  Now, if this isn't an option so that you can make is to have 2 disk groups and assign the virtual disks / LUNS that are connected to each host in their own disk group.  If you go to each host their own groups of disks, then you will need to stop the e/s as you move the Ramdisk to the new group of disks so that you want to discard any data loss.

  Please let us know if you have any other questions.

• Re-create a virtual disk (RAID 1) of two existing drives

  After several power outages, my server Dell PowerEdge T110 ii starts plu. The virtual disk (RAID 1) has disappeared, but the two physical disks are still visible and a State of readiness.

  Is it possible to create a virtual disk Raid1 of two existing disk which was composed the original virtual disk without losing any data?

  If this is not possible, is there a way to recover the data (image) and re - create a new virtual disk?

  I hope someone can help me.

  I don't think, because the process would have initialized the disc, which formats.

• initializing virtual disks

  I have a powervault MD1000 (Bay raid storage) connected to a backup server. It is set up with 3 virtual drives that each use 2 terabytes of storage in RAID 5 from our range of 8 physical disks.

  I had to replace two of the physical drives, and I need to initialize my virtual disks. In the Perc 6/E management screen VD, I can select the virtual disks (that show in red) and press F2 to display the operations, but the initialization button is dimmed and I can't select it. In the PD management screen, the new drives show as ready.

  How do I initialize my virtual drives? Should I delete them and create new virtual disks? It's my first time doing this, so please bear with me. Any help would be appreciated.

  I just updated the firmware of the 6th Perc to version 6.3.3 - 0002, which has a rep to support Dell recommended that I do, if this is useful.

  After you remove virtual drives, I was able to create a new virtual disk and initialize it. It seems that I just have to build the virtual disks from scratch.

  Thank you for your time.

• MD 1220 / PERC H800 - how Raid 1 virtual disks?

  Hello I'm trying to configure Raid 12 1 (two pairs disks) in my Inbox MD 1220 with PERC H800. I started with 12 discs as 12 virtual drives Raid 0 and have recently added 12 additional physical disks for a mirror. I am able to mirror 9 virtual disks but when I select my 9th virtual to the mirror, no drives appear as available. The other 3 drives are there in the 'ready' State, but manage to open or the BIOS configuration utility seem to be able to use them as candidates of mirror. My computer is running in a kind of limitation of Raid 1 with Cabinet / card? Operating system: Windows 2008 R2 Datacenter Open Manage 7.4 Latest firmware / drivers for PERC H800 thanks! Dan ouedraogo

  Hi Joey

  I just tried OMCleanup and reinstalled 7.4.  He exhibited the same symptoms showing is not the physical drives in the H800.  I can't find a download 7.2 but would be willing to try the previous versions.  A previous version of OM worked with the same controllers / speakers / computer, but I do not remember the version where I improved.  (I am an individual shop and am not very informed when it comes to managing open, its versions and how to install/uninstall).

  I can still kill the DSM SA connection Service by running a foolish occupation for the H800 report.  The report H700 works fine.

  Dan