new Pavilion dv5 laptop Virtual Disk Service restarts every minute

Similar Questions

• Unable to connect to the virtual disk Service, Virtual Disk Manager Interface not registered

  I installed Windows 7 Ultimate on this laptop as a new installation about six months ago.  Since then, I don't think I ever ran diskmgmt.  Today, I joined a new external hard drive usb, it reported the drivers installed fine, but then the installation bombed at the beginning.  I went to verity, what had happened and has run diskmgmt.msc (as an administrator), but she came back with the message "Unable to connect to the virtual disk Service" and also a small OK msgbox appeared with the title "Virtual Disk Manager" and the "Interface not registered" message

  I disconnected the USB hard drive and tried again diskmgmt, but no change.

  I restarted in safe mode, tried diskmgmt, but no change.

  I ran sfc/scannow, but it has reported that it found no errors.

  I checked that the virtual disk service has been configured as a textbook in services.msc, and event viewer showed that when I ran diskmgmt he started VDS and then stopped VDS.

  I tried again, but still not like before.

  Is there some dll I can't regsrv32?

  Thank you

  Marc

  Hello

  I suggest you to return the items for the following responses from Microsoft, he says same issues with trying the troubleshooting steps and check if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/cant-start-disk-management-unable-to-connect-to/31898500-9d84-4CB5-9ba3-c1f42e3b1ace

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/problems-with-Vista-after-unplugging-by-external/093f1660-160F-478f-b81a-493e963ffd9a

  http://TechNet.Microsoft.com/en-us/library/cc771775.aspx

  Note: it also applies to Windows 7.

  Hope the information is useful.

• When running Disk Management, get the error - failed to connect to the virtual disk Service.

  When I run the Snap on the local server disk management, I get an error message in the status bar: unable to connect to the virtual disk Service.

  Thanks, I have tried these things and nothing has solved the problem.  Here's what I did:

  (a) check the VDS service was manual and failures later per second are 'take no action '.
  ANSWER: Yes to manual and following, second has not changed to "restart the service" of "non-action".
   
  (b) sfc/scannow as administrator
  ANSWER: the System File Checker has found no problem (program reported no problem and findstr/c: "[SR]" on CBS.log doesn't have the list of issues)

  (c) restore to a previous system restore point
  ANSWER: I have tried restore points several more early, each of them failed

• Together open disk management and DiskPart will cause hang Virtual Disk Service

  Hello

  The issue I'm having is with the Diskpart tool and the disk management opening at the same time, the disk management GUI flashes 10 + time less than a second and then re-open or another tool will be blocked when connecting to virtual disk service.

  One please confirm, that it is a bug that is not specific to my system, but the operating system? My OS is Win7 SP1.

  Thanks in advance.

  Concerning

  Eric

  I don't seem to have the same problem.  Win 7 x 64 SP1 with updates as of April 12, 2016.

  

• Failed to retrieve the info on drive & virtual disk service

  I did research all day for the solution to this irritating problem!
  I get upgraded my Eee PC (it has system requirements) of Windows XP Home Edition - Service Pack 3 for Windows 7 Starter.
  Whenever I try to install the OS, this message always appears at the top:

  Windows could not retrieve information about the disks on this computer.

  I found that many people have solved this by activating the virtual disk Service and by assigning the value automatic. My problem is that I don't have such a service on my computer. The WIS IS NOT in the list.
  I tried Googling on how to install the service, but I simply find the answer.

  If anyone has a solution to my problem, that would be greatly appreciated!

  Starter is not available in the trade. Go to Home Premium or Professional. See also http://technet.microsoft.com/en-us/library/dd799282 (WS.10) .aspx Frenchie

• New Pavilion dv5

  Hi, I recently bought a Pavilion dv5 and am trying to uninstall the "fluff" (don't know if that's the right term). I have about 6 different versions of Microsoft Visual C++. Can I safely uninstall, or I won't regret it later?

  

  You need these runtime libraries, let them installed. Different versions are linked to different versions of Net Framework which are also installed and required by some software.

  .

• Why my laptop (hp Pavilion dv5) with windows Vista service 2 becomes hot little after I start it?

  My laptop HP Povilion dv5 (Notebook) get hot after awhile I connect and sceer becomes black breast t0 10 to 20 minutes. I want to know the reason and the solution.

  Hello

  overheating can cause sudden stops of your machine.

  with a laptop computer, make sure that the vents are regularly cleaned of dust, etc.

  Also make sure that the laptop is in a well ventilated area, not used on the bedspreads, blankets, etc.

  If above does not solve you may need to provide computer technology to clean inside and make sure that the fan/s work properly

• Pavillion g15-ab117na: new Pavilion g15 laptop turn not

  So I had my laptop since new year's day and today he knows he'd do an update and would need to restart. I ignored it but does it anyway a few minutes later and he went about installing updates as usual but now is not turn at all. The battery still had half of his life, and I tried to take the battery and now the power button and all that but nothing has worked! When I press the power button, the small light beside it flashes three times but nothing else! I can't even oped to remove the cd, the cd player. Can someone give me help? Thank you

  BTW, your laptop is a laptop 15 series, not G15.

  Your bars of memory are not accessible to the user. Contact HP for warranty repair.

  I will ask to have your escalated isue.

• HP Pavilion 15 laptop: want to buy the to my computer HP PAVILION 15 LAPTOP recovery disk

  My laptop has the stoppage of work yesterday after using the recovery disk created from my Hp laptop which gives the reasons below.
  Failure of the control of BurnBoot of P2PP
  Possible causes: -.
  1.Yello - bang was held at the device
  2. some failed installation in silent mode
  3 Found failed to PININST_BBV
  4 Found failed to PININST_BBV2
  5 found memory dump file.
  Suggestion: -.
  BB 1.checking - REGDEV. The pilot NEWSPAPER
  2.cheking - BB Apps. Application log
  3. check MEMDUMP_BBV. Journal of memory dump files.
  Note {for ODM}: -.
  If you know which component failed in the process of prenistall after checking above files please OTS it to the owner of the component.
  Furthermore, suggestions for contact TWN PDC NB-PreinPM or create PIN-Log and OTS with OTS category Image.
  [Checking the register device]
  Result-failed
  Device failed #0: -.
  Description:-Bluetooth controller
  PNP device ID:-PCI\VEN_FF42 & DEV_8650 & SUBSYS_00000000 & REV_00\4 & E572C4B & 0 & 01E2

  Hi @anupom,

  Welcome to the HP Forums!

  If I understand your messages that you encounter a problem with your HP Pavilion Notebook of 15 and problems related to lack of CD recovery.  Here is something that might help.

  Are there problems with your yellow exclamation Device Manager showing in it?

  Did you change hardware on the laptop?

  Note Remove all USB devices. Disconnect all non-essential devices because they can cause problems.

  Please get back to me how that happens.

  Click the thumbs below to thank me for my efforts!

  Thank you.

• HP Pavilion dv6 laptop recovery disk

  I bought a HP Pavilion dv6 notebook having Win 7 Home premium installed. He had 3 leave system and and a C:\ drive. I made an another partion and changed the drive letters to leave existing. After using the system for a few months, there are some problems with it and I want to go back to the factory settings. I tried, but could not recover my system. I have not the recovery disc for my system. Kindly guide me how can I recover my system to the preconfigured State. Where I can download a recovery disc for my laptop?

  Thank you

  Muhammad {information}

  @SorryHPbuyer

  I don't know what model said you it not available for, but HP still stocks recovery disc for many machines to Vista (not all), most Windows 7 and of course Windows 8 machines.

  I guess you have a XP or Vista early model? In this scenario, you should be able to get here:

  www.computersurgeons.com

• Connection to the disk Service virtual stalls

  Installed a second internal hard drive of my computer and when I go to disk management to format that nothing appears.  Not even my C: drive or my external hard drive. He just repeat "connect to a Service of virtual disk...". ». If someone could help it would be greatly appreciated.

  Hi Formalin6,

  Thank you for visiting Microsoft Answers.

  (a) how you installed the HDD internal?
  (b) who is the manufacturer of your computer?

  Please check if the drive appears in Device Manager.
  To do this, follow these steps:
  1. type devmgmt.msc in the start search box and press on enter.
  2. to check device manager if the drive is in the list.

  Let's try this steps and check if it works.

  i. Click Start-> type Services.msc in the search bar and press ENTER.
  II. find the virtual disk Service and make commissioning manual type. Click the Recovery tab, and make sure
  Second failure > no action
  Finally, the failure > taking no action.

  You can see the link given below where the user had a simialar problem.

  http://social.technet.Microsoft.com/forums/en/windowsserver2008r2management/thread/8b5d2c5b-C212-4E3F-96e3-91e668d3b178

  Hope the helps of information. Please post back and we do know.
  Concerning
  Joel S
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Pavilion dv5 drivers for own x 64 Vista install?

  I intend to do a clean installation of 64-bit Vista on my HP Pavilion dv5 laptop.  I entered the product number on the driver download page and was sent to the list of driver below:

  http://h10025.www1.HP.com/ewfrf/wc/softwareList?OS=2100&LC=en&DLC=en&cc=us&lang=en&product=3744203

  That's a lot of drivers!  Those who are the base drivers, I need?  The purpose of this new facility is to annihilate all HP software and unnecessary programs further.

  In addition, with my HP Slimline desktop computer, there a chipset driver that I need to first install.  Is there a equivalent to a chipset for the computer driver dv5 laptop?  I don't seem to see it on this list.

  Thank you!

  I believe that the chipset is included in the ATI Mobility driver, install first. With respect to the Atheros and Broadcom, check your device manager to see what card you have before clean install of Vista.

  So does the card reader, who wouldn't you have listed in D.M._Realtek or JMicron? You have a TV Tuner... If it is not necessary to install the driver.

  As to the validity and Persona_one is the driver and the other is the software to configure (if you have the device of fingerprints in option).

• MD1000 attached to MD3000. Virtual disk not on the preferred path

  Hello

  I have a MD3000i box connected to 2 boxes of MD1000, these are connected to a Dell Power Vault Storage server 2003 running.

  Last night I connected the 2nd MD1000 and added in 25 TB of drives worth. I had initially hurt mapping the new virtual disk after 20 minutes or so, I noticed that I had shot the Ethernet cable plugged into the Module Raid 0 by mistake. I plugged it back in and was able to map the drive and started the initialization of disks.

  I came this morning to check how everything is done and found an error on the table. Disk not on favorite virtual path, preferred owner: at location 0 RAID Controller Module. Current owner: Module to slot 1 RAID controller. Group MD1000_2 of disc. Ramdisk: Virtual4.

  Now, it seems that influence the new virtual disk that I created. I checked the path virtual disk property and all the other virtual disks are using path 1 and try that I created to use channel 0.

  The virtual disk seems to be working for the moment it is detectable and to initialize itself in the area of operations of MDSM. I'm under pressure to get the space of storage as soon as possible, so I can't really afford to have to blow the virtual disk and restart the initialization. I'm hoping a simple reboot of the storage array will cure the problem, but I guess I can't do so until the end of the initialization of the disks. I could also remap the path to the virtual disk, but I saw online that it does not solve the problem, and I always have to wait until the initialization is complete.

  Any help would be appreciated.

  Hello

  I deleted the disk group and created a new one that even once, did not help even after that I tried to change the path. I deleted again and created a new and then changed to RAID 1 controller quickly while he was still on the controller 0 (before it came with the failure of the path) as the preferred path that has cleared the error. There must be a mistake with the controller or the wiring to it.

  Thank you

• Cannot access connections wireless on HP Pavilion dv5

  Product name HP Pavilion DV5 laptop

  Windows 7 Home Premium operating system.

  Error message: Wireless message "no connection is available.

  No changes were made to the system

  I can't access wireless connections, even if the other devices have access to connections.  Wireless adapters work, but I can't seem to 'see' all wireless connections. /

  This has just occurred recently-never a problem in the past.

  Any recommendations?

  I recommend you update your BIOS. Go to http://www8.hp.com/us/en/support-drivers.html , and then type the name of your product in the search box.  Choose the Dv5 Entertainment Notebook that you have and select.  On the next page select your operating system Windows 7 Home 32 or 64-bit. Once on the correct driver for your laptop page choose BIOS in the list of drivers. Please update your BIOS and reboot. This should bring your WIFI connection. Please let me know if that solves this problem.

• Dell virtual disk are larger. You want to increase the size of the data store.

  Hello

  I started the implementation of a server ESXi 5.5 Update 1 this week. I didn't know Dell shipped the server with two virtual disks instead of one. I realized this _apres_ that I had already created the data store and setup a few virtual machines to the breast. I called Dell who sent specific instructions to increase the removal of the second (empty) virtual disk and add it to the main. In the end, I increased the single VD from 2 TB to 3 TB and I want to give the remaining space in my store of data.

  I tried to follow the article here that explains how to do this via the CLI.

  Well, he did not altogether. Fortunately, I was able to recover my datastore my setting start and end sectors to their original numbers. But I'm still left with this almost 1 TB of space that I can not attribute to the data store. After that I reread storage adapters in the client, the new Dell disk size resulted under measurement devices. Click on "increase...". ", generates the following error which led me on the way to the CLI method:

  Call "HostDatastoreSystem.QueryAvailableDisksForVmfs" to object "ha-datastoresystem" on ESXi '[myservername]' failed.

  I will paste my notes that I took everything by jobs. Things have exploded the rails when I put 4 partition size to the largest size. Any help, please?

  ---

  I use that as a guide:

  http://KB.VMware.com/selfservice/search.do?cmd=displayKC & docType = kc & docTypeID = DT_KB_1_1 & externalId = 2002461

  
  

  1 use start hardware device management tools to increase the capacity of additional disk to the device. For more information, commit your hardware provider.

  This has been done. The new size of the virtual disk is 2791,88 GB (TB 2,79188)

  
  

  2. open a console to the ESXi host.

  Pretty simple.

  
  

  3. get the DeviceID for the data store to change.

  ~ # vmkfstools Pei "/ vmfs/volumes/datastore1 / '.

  System file VMFS-5, 60 extending on 1 partition.

  File system label (if applicable): datastore1

  Mode: public

  Capacity 1971926859776 (blocks of files 1880576 * 1048576), 1042688245760 (994385 blocks) prevail, max size of the 69201586814976 file

  UUID: 534e5121 - 4450-19dc-f8bc1238e18a 260d

  Partitions split (on 'lvm'):

  NAA.6c81f660ef0d23001ad809071096d28a:4

  
  

  A couple of things to note:

  a. the device for Datastore1 ID is: naa.6c81f660ef0d23001ad809071096d28a

  b. the number of Partition on the disk is: 4 ' [...]: 4 "»

  c. the prefix, "naa," means "Network address authority" the number immediately after is a single logical unit number.

  4. Enter the amount of disk space available on the data store.

  ~ # df h

  Size of filesystem used available use % mounted on

  VMFS-5 1. 8T 865.4 G 971,1 G 47% / vmfs/volumes/datastore1

  
  

  5 team of the device identifier, to identify the existing partitions on the device by using the partedUtil command.

  ~ # partedUtil get ' / vmfs/devices/disks/naa.6c81f660ef0d23001ad809071096d28a '.

  364456 255 63 5854986240

  1 63 80324 222 0

  2 80325 8466884 6 0

  3 8466885 13709764 252 0

  4 13711360 3865468766 251 0

  ~ #

  
  

  According to the table in article KB

  4 13711360 3865468766 251 0 - primary #4, type 251 = 0xFB = VMFS, 13711360-3865468766 areas

  | |        |          |   |

  | |        |          |   \---attribut

  | |        |          \---type

  | |        \---se finishing sector

  | \---a starting from sector

  partition \---Numero

  
  

  Also note how the number of section start the old end sector number is + 1.

  
  

  6 identify the partitions that need to be resized and the size of the space to use.

  We want to resize partition 4. I don't really understand the last part of this sentence, however. Read more.

  
  

  7 the number of sector end you want for the target data store VMFS partitions. To use all out at the end of the disc space, remove 1 of the size of the disk in the areas as described in step 5 in order to get the last usable area.

  ESXi 5.x has a command to do this:

  ~ # partedUtil getUsableSectors "/ vmfs/devices/disks/naa.6c81f660ef0d23001ad809071096d28a".

  1 5854986239

  This means that we want 4 Partition of "naa.6c81f660ef0d23001ad809071096d28a" to be:

  13711360 - 5854986239 (i.e. the end of the disc)

  
  

  8 resize the partition containing the target VMFS Datastore using the command partedUtil, specifying the original existing partition and the desired end sector:

  Using the above information, our command is:

  resize # partedUtil ' / vmfs/devices/disks/naa.6c81f660ef0d23001ad809071096d28a ' 4 13711360 5854986239

  
  

  9 step 8, the partedUtil command can report the warning:

  He did not. Displacement.

  
  

  10. the tables of partitions have been adjusted, but the VMFS data within the partition store is always the same size. Now there is an empty space in the partition where the VMFS data store can be grown.

  
  

  11 launch this v vmkfstools command to perform a refresh for VMFS volumes.

  Fact.

  
  

  12 reach the VMFS Datastore in the new space using the command - growfs vmkfstools, specifying the partition containing the VMFS Datastore target twice.

  vmkfstools - growfs ' / vmfs/devices/disks/naa.6c81f660ef0d23001ad809071096d28a:4 ' ' / vmfs/devices/disks/naa.6c81f660ef0d23001ad809071096d28a:4 '.

  
  

  It did not work. I got an error:

  / vmfs/volumes # vmkfstools - growfs ' / vmfs/devices/disks/naa.6c81f660ef0d23001ad809071096d28a:4 ' /vmfs/devices/disks/naa.6c81f660ef0d «»

  23001ad809071096d28a:4 ".

  Cannot get device head way /dev/disks/naa.6c81f660ef0d23001ad809071096d28a:4 information

  
  

  Also the partition was very different to what I asked:

  ~ # partedUtil get ' / vmfs/devices/disks/naa.6c81f660ef0d23001ad809071096d28a '.

  364456 255 63 5854986240

  1 63 80324 222 0

  2 80325 8466884 6 0

  3 8466885 13709764 252 0

  4 13711360 1560018942 251 0

  
  

  I fixed it by running these commands:

  ~ # partedUtil resize ' / vmfs/devices/disks/naa.6c81f660ef0d23001ad809071096d28a ' 4 13711360 3865468766

  ~ # vmkfstools v

  ~ # partedUtil get ' / vmfs/devices/disks/naa.6c81f660ef0d23001ad809071096d28a '.

  364456 255 63 5854986240

  1 63 80324 222 0

  2 80325 8466884 6 0

  3 8466885 13709764 252 0

  4 13711360 3865468766 251 0

  Update:

  Since it was such a new machine, not in active production, we have safeguarded the VMs management off the ESXi host. Then flattened the virtual disk, recreated, and then created a store of data with the right size. (TPG this time, naturally.) We put the management of virtual machines on the data store. For Windows virtual machines, we have restored the using AppAssure. Everything is ok now.

  Need to add a new item to the list of punch: check what Dell has done the configuration of the virtual disks. :-)