Vista connection to WAG54G V3 wireless gateway

Similar Questions

• HP OfficeJet 6500 E710n: HP OfficeJet 6500 printer problem - connection to new Comcast Wireless Gateway E710n

  Use this printer (wireless) for a few years without problem connected to a Linksys 802.11n wireless router.  Connected to a desktop computer and two laptops.

  Comcast asked recently that I update my modem cable to a new wireless, which also serves as a 802.11n access point wireless router.  I installed the new point wireless very well and has been able to set up the printer on a wireless network. (IP, host name and Mac address doesn't appear on the thin printer).

  I reinstalled the printer drivers on each computer and everything worked very well last weekend.  This weekend, I went to turn the Scanner on the desktop (HP Pavilion, Windows 7, 64-bit) and it wouldn't work.  Then I reinstalled the device drivers and then there was no connection to the printer (many reboots the PC and printer at various times during the tests).  So I ran again the connection settings on the printer - and led wireless term.  (I was able to get the scan to the connection to the computer once on one of the laptops, never the office, then lost.  When I send to the printer, it goes into the queue, a very small number of bytes, cross (usually hear the printer starts) then there lost error "connection to a printer.  Oddly enough, a couple of times after canceling the print job in the queue, the printed test page actually printed a few minutes later...

  I tried to use HP Print & Scan Doctor - it was a complete waste of time.  To date, it has always died (do not connect not not the unit) and never been able to diagnose something.  I end up having to go to the Task Manager to kill him because he always hangs.

  Any thoughts?  I'm puzzled.

  Appreciate any help/ideas that someone can think.

  FYI - I have still no idea what the question is / was?

  Connected to the gateway wireless from Comcast to the old Linksys router and I went back to my old wireless network.  After you have reinstalled the printer drivers, re-connection of the printer to the old wireless network, re-start the printer and computers - I was (finally...) manages to get printing and scanning works again.

  What a waste of a morning/afternoon.

• I use a Windows Vista I can connect to my tv wireless?

  I use a windows vista I can connect to my tv wireless?

  I use a windows vista I can connect to my tv wireless?

  You can if you have a wireless converter.

  Wireless PC to TV:
  http://www.Amazon.com/Warpia-StreamHD-wireless-full-1080p/DP/B004GTN0T4/ref=sr_1_1?s=electronics&ie=UTF8&QID=1317710448&SR=1-1

• Recently installed vista update. I can no longer connect to my home wireless network.

  Recently installed vista update.  I can no longer connect to my home wireless network.  I get a message that says 'wireless link failed because windows did not receive response from the access point or wireless router.  I troubleshott he said of computing could be from low signal strength and yet it shows the strength of 100%.  Anyone have any ideas?

  Hello

  Check the firewall it is maybe it has been reset.

  In general.

  Most laptops have a physical switch for the wireless card. Read the manual of the computer and make sure that the wireless adapter is on.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Above everything is OK and it connects to the wireless router. Log in from any computer which is, or can be connected to the router with a wire wireless, disable wireless security, make sure that the wireless streaming is enabled and try to connect with no. wireless security.

  When the work turns on the Wireless security.

  Note * people sometimes make mistakes in writing and retype the password for security.

  Another way is to copy in the menu of the router and then paste it when asked of the wireless card.

  --------------------------------------------------

  I really checked and configured every thing and it doesn't work.

  Software firewall application that is not configured to allow local traffic (between the computer and the router is also a possible problem.
  some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  
  

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Computer connects to the network wireless as "local only".

  I am running Vista Home Premium SP2 on a HP Pavilion laptop.  I've never had any problems to connect this machine to a wireless network before, in hotels, at home, or anywhere.  My current home network is a modem - cable-> wireless-> wireless netgear n300 router.  My laptop connects to the internet via the modem cable directly or a wire from the netgear router.  I have a second, almost cell identical (it's intel, while the one who does not is AMD) which connects to the network wireless without any problem.  Two iphones connected wirelessely without any problem.  My HP laptop is the only one who refuses to connect to the internet.  Connected to the wireless network, it has access "local only".

  I tried the solution in this article: http://support.microsoft.com/kb/928233

  The question does not seem to receive an ip address, the computer receives an ip address.  I have disabled the IP v6, ran the norton removal tool, because I only had to a point and tried all other suggestions in these discussions: http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/0949042d-074e-43ab-ba95-3c06cc2aa6be and http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/bc08f0e7-49a9-4458-9e0e-149b2df362ec.  I've uninstalled and reinstalled the adapter and all TCP/IP and network protocols associated with it.  I am at a loss and would welcome any ideas.

  Here is the result of the command ipconfig / all:

  Windows IP configuration

  Name of the host...: Arrakis

  Primary Dns suffix...:

  Node... type: broadcast

  Active... IP routing: No.

  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :

  ... Description: Atheros AR5007 802. 11 b / g WiFi adapt

  Physical address.... : 00-1E-4C-B2-32-BC

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  IPv4 address: 192.168.1.5 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Wednesday, 28 April 2010 21:40:55

  End of the lease...: Thursday, April 29, 2010 21:40:55

  ... Default gateway. : 192.168.1.1.

  DHCP server...: 192.168.1.1.

  DNS servers...: 192.168.1.1.

  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: NVIDIA nForce Networking Controller

  Physical address.... : 00-1B-24-FA-DA-80

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 10:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {31C080CE-FE0B-4D50-B734-C782C9A25FBC}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {B198B0D3-B70A-4E3E-858D-9774C414EECD}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 14:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Teredo Tunneling Pseudo-Interface

  Physical address.... : 02-00-54-55-4E-01

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Card 6TO4

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  If anyone has this problem, it has been resolved by rolling the security settings on the router WEP.  I got the answer from the support client netgear.

  Amazing how two iphones, another laptop with XP and a laptop running Ubuntu Linux all about them without any problem, but wouldn't connect Vista laptop.

• Vista connectivity issues

  You attempt to add a second desktop computer for my house and I can't not hooked to the internet. Currently have the modem Wireless Linksys 'G' with one that Vista PC hard wired. Wireless for laptops many works. New desktop PC Vista unable to connect. I checked the router and it is set to DHCP. new hard line works well on my laptop, so think it's something with the new PC or an older router. Software provider Internet recognizes the network card, but still unable to connect. ipconfig shows no default gateway.

  I'm puzzled. Any help would be greatly appreciated!

  Hello

  Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
  Update your WiFi drivers on computers. How you are positioned in the router? Are there
  obstacles in the path? ONE WiFi device?

  Actually try updating your driver and disabling the network logon. Use a wire or to download to another computer
  and transfer via removable media.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your router wireless and wired - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Sometimes, I connect to other unsecured wireless and do not want to. My wireless 802.11 was swept away in several times, what causes this and is at - it a hotfix?

  I have an old toshiba phone that has msn phone dial inside program I use wire and that you don't have a phone number to put in what should be iI or is there a ms download

  I have xp home edition Service att tech and and when I take the computer to reinstall says the same thing > I have also a gateway that has the same problem, I sometimes connect to other unsecured wireless and do not want.  My wireless 802.11 was swept away in several times, what causes this and is at - it a hotfix.

  Hello

   

  I suggest you send your query to the solution Center MSN for better support for this topic:

  http://answers.MSN.com/

   

  Also suggest checking with you ISP provider

  http://www.att.com/eSupport/

• Can't detect the wireless, gateway 4025gz. mod, turn on wireless, Dosnt show the icon in the login screen. OK before wipjng drive.

  Can't detect the wireless, gateway 4025gz. mod, turn on wireless, Dosnt show the icon in the login screen. OK before wipjng drive.

  If it worked before wiping the disc, then it is likely, you are missing a player specific to material not included in WIndows XP.  Log on to the gateway website and download the drivers for the chipset and network.  Naturally, you will need to use a wired network connection.

  In general, Gateway provides the drivers specific to the hardware on a recovery of the system partition, and they also provide a tool so you can burn data on CD/DVD restore.  Do you stil have this partition or did you remove it?

  Every time I buy a PC, I always download copies of the material of the web site of the vendor-specific drivers and keep them on a flash drive, so that they are available when I wipe a PC and reinstall.  I also do the recovery partition recovery disks.

• Vista connects to my router, but for local access only.

  I am running windows home edition vista 32 bit on my laptop and until today I had no problems with my internet connection.  I've updated my norton 360 today and had no problems until I rebooted a few hours later.  I can connect to my router but it gives me local access only.  My Linux Ubuntu 10.4 and Mac OS X system is running to the same router with no problems.

  What can I do to connect my Vista laptop to internet?

  So I got on my windows to try what you say and guess what. -_ - (indifferent face) my vista decided to take my wireless and give me access to the internet after most of the month.  I don't know what happened.  I didn't have anything new in the last three days... It's fixed now, but I still don't know what it does break.  Any ideas as what caused it?

• Vista will not print works wireless but wired through router

  I have 2 wireless modem ATT DSL wire connected to a firewall server / print wireless Netgear FM114P ProSafe and a router 3Com to increase the number of connections.

  I have a Vista laptop that allows to print everything wired through my 3Com router connected to th Netgear FM114P ProSafe, server print/firewall wireless connected to a HP laserjet 6 p printer, but while Vista connects to wireless internet, it won't print wireless HP connected to the print server.

  I have configured the other portable XP to print wireless using the same ip address but can't get Vista to work.

  Hello

  Your 2 wire wireless mode, is actually a Modem/Router combo.

  I hope that your Prosafe device is connected as a switch with an Access Point.

  If it is connected as a second router you have independent networks that will not work against the second router NAT doble and thustwo.

  Re-set according to the principle here, http://www.ezlan.net/router_AP.html

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Printer Hp6700: unable to connect to the router wireless D - Link DI-514 when SSID Broadcast is set to no.

  HP6700 printer: unable to connect to the router wireless D - Link DI-514 when the router Broadcast SSID is set to no. My MAC laptop and HP laptop both work with the set SSID on no. If I change the router Wireless SSID Broadcast is YES, then the printer HP6700 can connect to the wireless router. I set up the printer it saying that the SSID and password have been, the same as both of my laptops, but it connects ever, unless I have change the router to broadcast the SSID. Help!

  Have you tried to update the firmware on the DI-514?

  You can also try to set a static IP address on the printer, and then assign the printer to the list of DHCP static in the interface of the router.
  To give a static IP address to your printer:
  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') 250
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway.
  -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS. It's Google DNS. You can choose a different external DNS if you wish.
  -Click 'apply '.
  Now, stop the router and printer, start the router, wait, and then start printing.

  After that you remove and re - add the printer to your Mac.

  Show support by clicking on the blue Kudos star in the post that solved your problem. Doing so will help the other members of the forum their solutions also.

• Win 7 cannot connect to internet, found wireless & LAN network but cannot access the internet.

  I've updated my laptop lenovo Y430 to Windows 7 Home Premium about 6 months ago, it has been working fine until last week, I just can't connect to the internet more. I used to use a wireless network, now it says that it is connected to the network, but 'no internet access', while the signal says it's just. I also try to always use the Wired internet, not luck, and worse yet, he says no 'identified Network/No access to the Internet.

  "I have troubleshooted, that is the message he gave me: 'Connection to the Local network' is not a valid IP Configuration.

  I run 'ipconfig' cmd and this is what gives me:

  C:\Windows\System32>ipconfig

  Windows IP configuration

  Wireless network connection Wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
  Link-local IPv6 Address...: fe80::e99e:3f78:35 c 3:7056 %11
  Autoconfiguration IPv4 address. . : 169.254.112.86
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :

  Tunnel adapter isatap. {B10AA6ED-FDE1-4A0B-A968-3E7DB87E4CCF}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :

  Card tunnel Teredo Tunneling Pseudo-Interface:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :

  Tunnel adapter isatap. {F438E2F9-36AA-4DE2-8BAB-4A72511B70D2}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :

  C:\Windows\System32 >

  and I've run ' ipconfig/all', that's what I got:

  C:\Windows\System32>ipconfig/all

  Windows IP configuration

  Name of the host...: salt - PC
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Intel(r) WiFi Link 5100 AGN
  Physical address.... : 00-16-EA-DC-69-22
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
  ... Description: Broadcom NetLink (TM) fast Ethernet
  Physical address.... : 00-1E-EC-96-77-04
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::e99e:3f78:35c3:7056% 11 (Preferred)
  Autoconfiguration IPv4 address. . : 169.254.112.86 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  DHCPv6 IOOKING...: 234888940
  DHCPv6 DUID customer...: 00-01-00-01-10-38-1C-FD-00-1E-EC-61-19-2C

  DNS servers...: 85.255.112.123
  85.255.112.234
  NetBIOS over TCP/IP...: enabled

  Tunnel adapter isatap. {B10AA6ED-FDE1-4A0B-A968-3E7DB87E4CCF}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft ISATAP adapter
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Teredo Tunneling Pseudo-Interface:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {F438E2F9-36AA-4DE2-8BAB-4A72511B70D2}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Adapter Microsoft ISATAP #2
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Please answer asap, HELP!

  Thank you.

  Sincerely,

  Evan

  

  Yes.

  Routers and switches are different types of network devices.  Routers are "smart".  Switches direct network traffic between computers on a single network, while routers can act as the interface between two networks (for example, the Internet and your Local network). There are many explanatory pages on the Internet about it. Here'sa .

  Actually, most "routers" sold for home use today incorporate both a switch and a router (and in the case of "wireless routers" also incorporate a wireless access point). Routers include usually a (NAT ) network address translator, also a DHCP Dynamic Host Configuration Protocol (), a proxy of domain name Service (DNS) server, and a hardware firewall to protect the local network from malicious intrusion on the Internet.

  Your provider of Internet service through your cable modem, "sees" the WAN port of the router, as a computer (which is) generally configured to automatically obtain its IP address.  The ISP's DHCP server assigns this port the only IP address that is allowed to you.  It is an 'external' or 'public' IP address, and this is the address that other computers elsewhere on the Internet use when they drive traffic to you.

  The router's built-in DHCP server assigns 'private' IP addresses for each of the computers connected to TI (no matter if they are connected by wire or wireless).  As a general rule, these are of the form 192.168.1.x or 192.168.0.x, where x goes from 1 to 254.  These IP addresses are not 'seen' by computers on the Internet.  Instead, the feature NAT on the router directs traffic to your public IP address to the correct of your internal computers (and vice versa).

  A switch can't do it all.  If your authorized service provider, you can connect to your switch directly to your modem and the ISP's DHCP server assign an IP address publicseparate to each computer connected to the switch.  Because your ISP does not allow more than one public IP address from your account, its DHCP server assigns such address to the first computer he sees connected to the switch.  If several computers are then connected to the switch, the ISP's DHCP server simply ignores them: too bad, computer #2, you do not get an address, and so you can't connect to the Internet.

• Satellite A300 - 12K unable to connect to the ADSL wireless modem

  My Satellite A300 - 12K suddenly cannot connect to a dsl wireless modem... There are no changes made to the parameters of
  However it connects to a modem that is not encrypted.

  Any idea what the parameters might have changed?

  Hello

  Why you n t reset the modem and check the settings?
  Configure encryption of the modem settings and encryption settings of the WLan card.
  Check if you are using the right key and change it if necessary.

  Sorry but there is no magic answer for you question, we must check everything and if necessary you must reconfigure everything!

• HP Envy 4502: printer connection on my laptop wireless problem

  I installed the software on the disc that came with my new HP Envy 4502 printer on my HP laptop. He says that the software is installed correctly, but the printer is not connected wireless. Have you tried connecting via the usb cable and it worked. However, whenever I try to connect wirelessly, it fails to connect.

  I tried troubleshooting tips sevral time but still have no luck.

  My husband was able to insert the disc into his Dell laptop and connect the printer even wireless with no problems at all. This laptop is Windows 7 Professional.

  I'm getting more and more frustrated by the present, thank you I am a novice where computers re concerned, but that he thought that by purchasing an hp printer to go with my computer hp laptop, things would be easy.

  Help, please

  Take a look at this link on the implementation of WiFi.

• Need help setting up WebUI for the Wireless Gateway

  I have problem installing a Web UI for my demo project.

  I just do temperature is a simple application of WSN on a node of thermocouple WSN-3121 and it logging on a RT NI 9792 wireless gateway.

  Then, I wanted to create a web user interface and display whats in the user interface of the gateway - see the project.

  SO I'm stuck with the web INTERFACE coming.  I tried to read as much as I can but I still don't know what I'm doing wrong.

  As far as I see it, I need to create a web service in the construction for my gateway specifications and place the gateway_main.vi like the vi to use.  Then build and deployment.  Once it happened, and I run the vi on the bridge, I created a Web user interface as shown in the picture, where it counts the the gateway web service using 192.168.0.16:8080 - that works very well.

  When I run the Web interface, it is just and expires.

  I am using LAbview 2010.  Help, please.

  Hello markza,

  Your approach using the Web user interface designer and understanding its use case is quite accurate, the question lies in the web service, you have deployed. The VI you build as web service, which is gateway_main.vi, while loops inside and so cannot be used as a web service. The reason for the timeout is that your user interface Builder application calls the web service LV2010 and is stuck there for waiting time loops to complete. Also, the data type of cluster is not supported in the user Web interface Builder, so you'd have to break up from the entrance of the time of picking for the node wireless in two separate digital inputs.

  I recommend creating a Subvi out of your code inside of the while loop inside gateway_main.vi. The Subvi must have two digital inputs to replace the cluster (as mentioned above) and do not have one of the Boolean inputs Start or Stop. Output would remain the same, that is, two doubles and a Boolean value.

  I would like to know if this is useful and if you have any other questions.

  Thank you!

  Dieudonné jgfcnbh

  The user of LabVIEW Web R & D interface generator