Vista detects wrong monitor

Similar Questions

• My Aspire V7 582PG cannot detect external monitors

  I recently bought an Aspire V7 582PG, put in a new SSD and then installed Windows 8. The laptop works well, except that it cannot detect external monitors (in Control Panel, I get "Has not detected a different view".) I tried with 2 monitors (different models) that are known to work, via HDMI and VGA.

  I thought it might be a driver problem. Device Manager > 'Graphics cards' show 'Display card base Microsoft' and 'NVidia GEForce GT 750 M. The two drivers are up-to-date. 'Monitors' shows 'generic PnP monitor", which is also updated.

  Then I went to http://us.acer.com/ac/en/US/content/drivers to download the driver for my model. The only one who had the relevant air was:

  Monitor

  ELANTECH

  The HID monitor drivers

  1.1.5

  Installer here: http://global-download.acer.com/GDFiles/Driver/Monitor/Monitor_ELANTECH_1.1.5_W8x64_A.zip?acerid=635...

  But when I unzip and run the Setup window closes a few seconds; I think it hangs, rather than installing correctly.

  Any suggestions?

  My Acer tabs they need additional drivers to recognize the HDMI port.

  I think having unzipped in a directory and open a DOS window with admin rights and run the application inside that. At least if an error occurs, you should be able to see. Sometimes just doubleclicking opens and closes a window so fast that you do not see the error.

  Also in looking at support for a 'ultra' V7, I see several drivers for the chipset VGA and monitor. All may be required for the video display to work.

  You see multiple devices when you press Windows-P?

• Windows Vista detects the wireless network but will not connect to it. Two other users in the same office connect without difficulty.

  The title says it all really.

  I was connected and working normally for about an hour this morning, until suddenly the connection has been lost.
  Windows detects the wireless network but will not connect. Two other users in the same office connect without difficulty.
  Help, please.
  Thank you.
  original title: vista detection network but will not connect

  Hi JulianBeach,

  1. you have made no changes to the computer before the broadcast took place?
  2. What is the exact error message you get?
  3 is connected to the domain of the computer?
  4. what happens when you try to connect to the network?

  Try the steps from the following link:
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Additional information:
  Wireless network card: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/wireless-networking-frequently-asked-questions

• Touch a touch monitor moves the cursor to respond on a different system Windows Vista multi-display monitor

  Hello!

  I joined just a touchscreen multi-touch Dell ST2220T the VGA on a Toshiba laptop. The multiscreen correctly display features, however touch events on the new monitor are sent to the screen of the laptop. There doesn't seem to be a way to make the new monitor the primary monitor, as in something similar here. In addition, if the option to solve this problem in a similar way to this solution exists in Windows Vista, it is certainly well hidden. I've sifted through all the options in Vista and came away empty-handed.
  No one knows how to fix this problem on WIndows Vista with a built-in screen that can not be changed by default?

  Hello

  Is the touch screen as the default monitor?

  Set up your touchmonitor active by default. To do this follow the steps mentioned in the link below

  Change-Display-Settings-on-multiple-Monitors

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-display-settings-on-multiple-monitors

  For more information, see the links below

  Set up multiple monitors
  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-multiple-monitors

  Understanding multiple monitors
  http://Windows.Microsoft.com/en-us/Windows-Vista/understanding-multiple-monitors

• Windows 7 does not detect external monitor!

  Hi I have a huge dilemma!

  My laptop does not recognize the external monitor. Earlier in the day, he detected the external monitor and perfectly well worked through to extend, in doubles, you name it. However, after restarting my computer, I was unable to get the external display to be recognized...

  I use a laptop Lenovo y470 and nvidia gt 550 m 64-bit. I've updated the grahpics card but in vain...

  The way I have it plugged into the external monitor is using a hdmi cable to connect the laptop to a monitor for a DVI-HDMI adapter. Basically, the dvi port became a port hdmi with this adapter.  its dvi - d.

  I think that restarting the computer developed a few updates and the graphics card only connects via VGA or HDMI and DVI not? I'm not sure... I'd love any idea of a solution.

  Hello

  If you do not see an option named multiple displays in your display settings, then Windows isn't detecting a second monitor plugged into your desktop computer. Or else, it does not detect an external monitor plugged into your laptop. When Windows detects this monitor, it will appear in the drop-down list next to the screen. If you do not see that what listed there, try click on Detect.

  Make sure that the monitor you want to extend your desktop is turned on and plugged the correct video port on your computer. You may also need to select the correct source labeled on the controls of your monitor to ensure that the monitor is using the correct video port. For more information, consult the manual of your monitor or go to the manufacturer's Web site.

  Method 1:

  For more details, see the following articles:

  Work and play better with multiple monitors

  http://Windows.Microsoft.com/en-us/Windows7/work-and-play-better-with-multiple-monitors

  Move windows between multiple monitors

  http://Windows.Microsoft.com/en-us/Windows7/move-Windows-between-multiple-monitors

  Method 2:

  I suggest you to check the history of update for the recently installed updates.

  See the Windows updates are installed

  http://Windows.Microsoft.com/en-us/Windows7/see-which-Windows-updates-are-installed

  Method 3:

  I suggest to see the link and try to run the troubleshooter and check if it helps:

  Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 4:

  I suggest that you try to do a system restore and check whether the problem is resolved.

  In Windows 7 system restore

  http://Windows.Microsoft.com/en-us/Windows7/products/features/system-restore

• Comments by R2 window 2012 has not detected several monitor?

  I had a problem where several monitor is not detected correctly by the guest operating system (Windows 2012 R2). If I choose to use this monitor mode full screen, all monitors (3 x) will show the guest in mirror mode operating system. I tried to go to the display option in the guest to do the extended desktop, but Windows OS tell me only 1 monitor detected?

  VMWare fusion Pro 6.04

  OSX 10.9.4

  Mac Pro (cylinder) E5 Core 4 16 GB Ram D300 graphic

  3 X screen: Apple Thunderbolt X 2, Dell 24 "monitor x 1 (1920 * 1200)

  Thank you

  OK, figured it out, it works now. I needed to set the full screen display, use all the screen, and then start the machine virtual everything in full-screen, then Windows (guest operating system) are able to detect all monitors.

• How can I prevent windows 7 from auto-detect my monitors?

  I have a multi-screen with two computers and two monitors Setup. My main screen is shared between 2 computers on a KVM switch and my secondary display is connected directly to my win7 box. When I switch the KVM away from the area of win7, windows detects that there is more connected to my main screen and flies all my windows open to the secondary display, hide the Windows I wanted to see. How to disable this behavior?

  I've seen messages on the deactivation of TMM in vista, but TMM does not appear in the Task Scheduler in windows 7.

  What makes this even worse, is that when I flip the switch KVM back (so my first is now connected to win7 box once again), about 10% of the time windows does not automatically detect the screen and I have to open the screen resolution settings and click on the button find.

  Maybe this thread will help you:
  http://social.answers.Microsoft.com/forums/en-us/w7hardware/thread/dd31eb3a-80f3-4e61-9674-fa5d7d065ea3
  I have yet to try myself.

  If this is not the case, this discussion has people with similar problems.
  http://social.answers.Microsoft.com/forums/en-us/w7hardware/thread/84f41660-1933-4109-9b13-1ea8a1c27be7

• Z50 does not detect second monitor HDMI

  I recently purchased the Lenovo Z50 - 70 with 16 GB of ram and nvidia 840 m video card.

  Today I tried to connect the laptop to my LG 47LA6208-ZA, but the laptop does not recognize a second monitor. When I try to detect that another monitor nothing find it.

  I don't know there is no problem with the tv or hdmi cable, cause another pc with a cable hdmi even on the same port hdmi works perfectly.

  Any ideas what could be the problem here? I have already updated all the drivers.

  However, I do not know on what card video the hdmi port is on, the nvidia or intel on board.

  Any help would be appreciated!

  It turns out that the hdmi cable is the problem after all! Which is really strange, cause there is no problem with the other pc. However, I am very happy that this is resolved! Thanks for the support!

• The installer for Windows Vista is wrong...

  I was recently given an old "Lenovo Thinkpad SL500' with a failing HARD drive.  On the Palm of the laptop is Windows label that reads "Windows Vista Basic". I put in a disc of Windows Vista (x 86 version) and windows load, and to enter the serial number, it starts to install "Windows Vista Business" (perhaps the original owner updated the version of windows). At the end of installation, I go to activate and I like that it's the wrong version of windows for the serial number, hmmm... !  Think it should have been the version 64-bit (x 64), I perform the re - install, once again tell them he set up "Windows Vista Business" (64-bit version). Still, I get the same error message when you try to activate.

  Time to cheat, I re - install again, but don't get me the serial number, which then gives the option to select the version of vista to install, this time I select Vista Basic (32-bit and 64-bit later). Windows installed twice and both times it fails to activate, this time with the error "Enter a different product for activation key", and Yes, I type in the serial number from the label (which windows it is was brought off the coast of the COA), still with no success.

  Is it possible to say that Windows belongs to my serial number, or is it possible that the previous owner upgraded to a version of Windows 7 and changed the COA. ??

  Vista OEM integrators of systems and DVD retail are the same both contain the files for the editions of Vista that you mentioned, and that is the PK that determines which edition is installed.

  Unfortunately, there is no list to check a PK hand to see which edition it corresponds to the.

  Lenovo are those who need to check with as to what is preinstalled on it.

  Here is their information on it:

  https://support.Lenovo.com/au/en/documents/MIGR-75229

  'Detailed features - ThinkPad SL400, SL400c, SL500, SL500c'

  Software
  Operating system Windows XP Professional Windows Vista Starter Edition (32-bit) Windows Vista Home Basic (32 bit) Windows Vista Home Premium (32 bit) Windows Vista Business (32 bit) Windows Vista Ultimate (32 bit) Notes: Earlier versions of these operating systems are not supported. Operating systems other than those pre-installed on systems cannot provide full adjustment functionality

  See you soon.

• Vista detects no not my wifi? urgent please

  Experts,

  My laptop, dell vostro1500 running vista as being arrested to detect my wifi at home. No idea why. strange enough my phone connects to wifi and my laptop is looking other wifis except my own. so I checked both devices work fine regardless, it's just my lappi does not detect my wifi.
  What, I did and tried
  1. reset router
  2. change the SSID of the router.
  3-change ip address of the router (from 192.1681.1 to 10.0.0.1)
  4 removed all profiles laptop wireless
  5-merges all profiles in 1
  6-remove wifi adapter laptop, started and stop, put the card back in, restarted...
  7-re drivers installed
  nothing has worked...
  so, I came here to ask for help...
  Why the damn thing detects is not my home network... when its detection and connect to other wifi networks...
  He worked for months and stopped yesterday.
  Any idea?
  concerning

  Hello

  I suggest to create a network profile with reference to the link:

  http://Windows.Microsoft.com/en-us/Windows-Vista/create-or-modify-network-profiles

  Check if it helps.

• Vista and multiple monitors

  I'm using Vista Ultimate 32 bit system. When I created multiple monitors on my laptop my screen saver does not work.  I put it in the slideshow personalized with photos of my images. When the time for the screen saver activate the screen turns black with a procession of white dashes strung on black screen and has a long delay in retune to active screen when embarrassing. I've been to monitor manufacturing webite and I have the latest drivers. They say MS problem with Vista which they have many complaints on this subject.

  Try using a simple screensaver as the starfield and see if it works better - maybe it has problems with the customized version.

  I hope this helps.  If so or if not post back and we'll see if we can find another solution.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• T400 and Advanced Mini Dock - does not detect DVI monitor

  I have a T400 with integrated graphics and Windows 7 Professional 64-bit, and I recently bought an Advanced Mini Dock for it.  I have a Dell 1800FP monitor connected to the dock via the DVI output.  When I anchor the T400, the system does not detect the external monitor.  If I go to the resolution of the screen and click on detect, it does not appear.  The weird part is that if I reboot then than in the dock, when the system comes back he * is * detect and use the external monitor.

  Any ideas what's happening?  Other equipment connected by the base (USB, Ethernet cable devices) all work very well.

  I think I solved this problem.  I uninstalled my video driver and installed the latest version from the Lenovo Web site (which was more recent than the one found by Lenovo System Update).  Now my system properly detects the external monitor when I attach to the docking station.

• Windows 7 doesn't detect 2 monitors connected to dvi and vga ports on AGP card

  Windows7. Have a G-Force FX AGP card with a vga and dvi port. Include in annex a vga monitor and a dvi. I get the same screen on both.  Windows 7 does not detect the 2 monitors! Any advice?

  It is not the drivers of FX for win7

• Photoshop CS5 always chooses the wrong monitor in dual monitor profile?

  The folklore is that if you go to EDIT/COLOR SETTINGS and open space RGB Working drop down, and then up on the "Monitor RGB" line in what he says is the profile monitor that photoshop is actually to aid.

  If that's true, then I expect if I run photoshop on my monitor 1 he would show the monitor 1 profile, and if I have PS on Monitor 2 it would show the 2 monitor profile. But in fact, it always shows the monitor profile 1. Naturally, this creates anxiety that PS uses the wrong profile to display my images, because I normally work with the image on the screen 2.

  My configuration: Windows 7 64-bit, PS 12.0.1 x 64. Matrox M9120 graphics card drive two monitors. MANAGEMENT of Windows CONTROL COLOR/PANEL displays a different profile active on each monitor.

  (By running photoshop on a particular monitor, I want to say I run photoshop, drag mode non-plein screen on the desired monitor and close it.) Then I run it again and it starts on this screen (including the start screen)).

  What photographers want to know, that's exactly what photoshop monitor profile used when displaying an image? Where is the answer to this question please?

  The profile associated with this display in the settings of the operating system.

  Photoshop DO fixes for each display separately, using the profiles associated with each screen and correction the same for images that run through several screens.  If you move the window, Photoshop updates the values of color accordingly.  He has done that since Photoshop 5.0.

• Firefox opens the wrong monitor

  I have a monitor left and right, and normally FF opens on the left, but now without reason, it opens on the right side. I want to open on the left side

  gemarkk said

  I have a monitor left and right, and normally FF opens on the left, but now without reason, it opens on the right side. I want to open on the left side

  Hello

  If Firefox is maximized and then minimize the window and drag the window to the correct monitor and close Firefox to save the setting.

  After the reboot, you can maximize again.