VLAN and exchanges

Similar Questions

• VLAN and Exchange server

  Hello world

  We need help on our Exchange Server configuration and VLAN.
  Since I am a beginner in the configurations of VIRTUAL LAN.
  We use SG300 Cisco switch and the Exchange Server.

  We have 2 network cards on our server, with 1 having a static IP address of Public (internet) for the internet which is directly connected to our ISP modem (complete with the IP address, subnet, default gateway, and DNS mask), the other NETWORK adapter a static IP address of Local (intranet) for the LAN (with an IP address and the subnet mask).

  Our problem is that we cannot add a gateway on the 2nd NIC (intranet) of conflicts with the gateway on the map of others because he said.

  We want to add a default gateway on the 2nd NIC (intranet) have become accessible to other VLANs.

  How the server are accessible to others different VLANS on our network?

  What will be the best approach on this?

  Thanks in advance.

  J

  You must add routes to your windows, routing table.

  So if your server is in VLAN 10.10.10.0/24 and has the IP address of 10.10.10.2 and your router is 10.10.10.1 then you can add routes to all your VLAN by adding networks and their routing through 10.10.10.1.

  For example, in your Windows command prompt, you must type:

  Pei route add 10.10.11.0 MASK 255.255.255.0 10.10.10.1
  Pei route add 10.10.12.0 MASK 255.255.255.0 10.10.10.1
  Pei route add 10.10.13.0 MASK 255.255.255.0 10.10.10.1

  This would make your computer access all VLAN interns as well as make it accessible from VLANs.

• My iPad was stolen and exchanged by another how can I know who is using mine

  My iPad was stolen and exchanged for another how can I know who is using it?

  You can use Find iPad to see the location of the device if it is connected to the internet

  Do NOT you go after him - give the information to the authorities

  If you have an iPad that was initially not yours - you can enter - in other words - past the lock of activation?

• SBS Server 2003 and Exchange Server - need access, but don't have HARD drive

  Hello

  A couple of years our sever dies completely, but we kept the drive HARD, but unfortunately not the CD with the software or the software key. So, I now have 2HDD, the original boot partition and the other with the data. now as well clean and fully functional and connected to an old desk. I can see everything beautiful, but I can't boot from the original boot drive (I tried simply disconnecting desktop boot disk and windows for 1 second logo shows a d, then chucks back me to the initial charge (BACK?).) The point is that I need to boot into SBS2003 with exchange server installed in order to access a handful of old emails that have become extremely important, as well as to run an old version of Filemaker server, which can run on any newer operating system

  I tried, by the way, a converter for swap files and I can see the directories but I think that, unless I paid $xxx.00 for something, which I can't afford now, so I will not get the emails and all attachments back.

  So my question is this - is anyway that I can use the original startup disk in a new hardware environment to restore sbs 200 and Exchange if you work? I paid huge sums for both, so I think I should be able to use it again!

  Thank you very much

  Gor

  This issue is beyond the scope of this site and must be placed on Technet or MSDN
  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Support for windows 2 k 12 R2 and Exchange 2 k 13 in Oracle VM 3.3.1

  Hello

  We intend to deploy Windows 2 k 12 R2 and exchange 2 k 13 in Oracle VM 3.3.1 that is based on the Xen 4.0 hypervisor.

  Kindly let me know if windows 2 k 12 R2 and exchange 2 k 13 is supported on LMOs 3.3.1 or not. If not, then what is the possibility of support in the near future of microsoft. Also let me know the list of supported OS windows and versions of exchange for LMOS 3.3.1

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Convert a single number to a hexadecimal string of 32-bit and exchange the high and low bytes

  I need to convert a number single precision floating decimal to hexadecimal format of 32 bits, share the high and low bytes and that convert a hexadecimal string.  I tried to use the 'Word of Swap' function but it seems to have no effect on the unique number.

  Then

  A single decimal number of entry: 100

  Convert 32 bit hexadecimal string with the low byte first: 0000 42 8

  Anyone have any ideas?

  Thank you

  Slightly lighter, try to cast U32 and exchange words. Same difference.

  (apparently, exchanging words is a NOOP for SGL, but still accepts SGL without constraint. Interesting...)

  

• LRT214 VLAN and site to site vpn

  Hello everyone, I am a bit new to the network of this aspect and was looking for some advice.  I am looking for several routers LRT214 to configure VPN site to site to our main office at 4 locations.  There are 2 VLANS and subnets - one for the network secure (vlan native 1) and one for comments wireless (vlan 2).  It is very good and works well for lan segregation locally.

  IPSEC tunnels do not pass the tags vlan, my question because I will be able to restrict traffic through the vpn tunnel to vlan 1 and deny traffic to vlan 2?

  It appears in the documentation that VPN traffic can be limited by IP address or the local subnet.  My concern is that if there is no way to bind or bridge to the VLAN selected, an adjustable static IP address on a device on the vlan 2 were part of the traffic permitted (vlan 1 range), and therefore cross the tunnel for devices vlan 1 on remote sites.

  Thanks for any input you can offer.

  Hi, seedtech. The VLAN used for the VPN is the default VLAN. So if a tunnel is created, it will cross through the default VLAN.

  Jay-15354

  Linksys technical support

• Implementation of VLAN and QoS for VOIP on SG200-18

  We recently purchased the smart switch SG200-18 to replace a Netgear switch. We are moving our phone service to VOIP through our local ISP as well.

  I currently have the VOIP phone plugged into Port 17 on SG200-18 (it is a Grandstream Cordless VOIP phone).

  I want to put the VOIP phone on one VLAN separate from the rest of the network and optimize QoS parameters so that the VOIP phone has exceptional audio quality even during network traffic.

  Here are my questions:

  1. do I need to set anything on the type of port to Port 17 (because it resembles a shape any Combo port)?

  2. How can I do to isolate VOIP telephone it's own VLAN (I see the parameters VLANS and VLAN voice, not sure that one to use;) I've tried to set a VLAN and broke the Internet connectivity on the phone until I went and removed)?

  3. do I need to adjust the QoS settings to switch to better optimize the VOIP phone?

  Some additional questions about the GS200-18 in general:

  1. do I need to adjust the parameters of the system on the switch time? I am in the Central time.

  2. do I need to adjust the Green Ethernet/Energy Saving parameters or should I stay with the default settings?

  In addition, a couple of "getting started" questions for Cisco:

  1. I registered an account My Cisco. What should I do to register my switch with Cisco and associate with my My Cisco account?

  2. What are the benefits of purchasing a contract of Cisco Small Business support, and how much would it cost the SG200-18 (I ordered it from Provantage)? I'm curious to see if it's worth the money.

  Here's my 'features ':

  Switch: SG200-18

  VOIP phone: Grandstream DP715 and 710 handsets

  Plugged in: Port 17 on SG200-18

  Services: Internet Local (Direclynx)

  Type of connection: 3 m down / 500 k up DSL move to a future wireless connection that will give us higher speeds

  Backend VOIP provider: VOIP Innovations

  Router: Apple Airport Extreme AC model (all Macs and iOS devices and the OS X Server on the network, so I use the Apple router facilitates installation, because is not QoS, trying to QoS and VLAN in the switch)

  Thank you all!

  Hello

  I'll just go to the list again:

  1. sounds good in the port from the drop-down list. So can I just connect the VOIP phone and go with it, correct?

  Yes, just plug in ethernet combo port and it will work.

  2. is not an issue, but I agree, Apple likely isn't compatible QoS or VLAN.

  3. thanks for the info on time/NTP settings. If I wanted to go there and try to configure NTP, how much is it and what I have to do? I want to I can give it a quick try.

  To Setup NTP on the switch is quite simple.  Go to Administration > Time Settings > time system and check the boxes to activate the main clock Source (SNTP)

  Then go to the settings of the SNTP page and add a new entry with the IP address of an NTP server.  There is a list of available NTP servers here:

  http://www.pool.ntp.org/en/

  You must also ensure that the switches Administrative default gateway is set correctly (it must be set the to the default gateway, probably the most convenient airport) so the switch can contact the NTP server.  That option is set under Administration > Interface Management > Interface IPv4.  Change the user-defined default gateway and enter the IP address of your airport (or whatever your default gateway for your network)

  4 sounds good on the Green Ethernet settings. I'll leave it as default value.

  Yes, better to just let those unless you have weird problems with ports disconnect, who can sometimes be caused by Green Ethernet, but if there's nothing like leave it on and save a few watts.

  5 sounds good on does not need to attach my passage to my Cisco account. Should I fill out a form any registration of the product with Cisco before calling support?

  It is not a record for support.  The only thing we need you to do is to create a Cisco account, but you have already done this, so if/when you call in support, you just need your ID for Cisco (also called a CCOID sometimes) and the serial number of your switch.

  6. thanks for the info on the Service contract. Is it something that I would need to order directly from Cisco or I who would get my Cisco partner (Provantage)? After the three years is up, treat yourself to renewal or it just falls? Is there a certain amount of time I have to buy the Service Contract forward make me ineligible?

  Support contracts are purchased through a partner Cisco, or you can get them online for the CDW or Newegg for example.  Basically, you have until the expiry of your current aid for the purchase of a new contract.  For example, right now your switch comes with 1 year of technical support.  You can only buy a contract while it is still active.  Once your three-year contract is about to run out, you're in the same situation.  You can renew it before it expires, however if you leave is up, you will not be able to put a contract on it.  Contracts are not my specialty, however, so you can check with your partner for complete details.

  7. sounds good to how data use VOIP calls. His dislikes too. :-)

  I agree, a voice call is not much traffic.  What you have described you probably don't have problems, although of course I can't guarantee that.

  8. because it is from your provider and they specifically mentioned the VOIP, I would say that you'll be fine here.

  You had also placed on your airport using access point behind a router in small businesses.  I would like to say that it is possible, a large number of wireless routers have an option to put access point only mode or something like that, but you should check with Apple on how to do it.

  Insofar as a Small Business router if you decide to upgrade for the options VLAN or QoS, I would recommend the RV180, or perhaps the RV320.  Two of these models are available with or without wire depending on what you decide to do with the airport.

  I think I got all the questions, but if not just let me know,

  Christopher Ebert - Network Support Engineer

  Cisco Small Business Support Center

  * Please note the useful messages *.

• 4.1 unit. (1) and Exchange 2003 SP2

  Is the unit 4.1. (1) and Exchange 2003 SP2 is supported, I'm planning on the upgrade of the existing unit 4.0.5 to 4.1. (1) at - it no cisco Documentation on this subject?

  Mrugresh,

  SP2 is listed on the recommended cisco page updated, at the following location.

  http://www.Cisco.com/univercd/CC/TD/doc/product/voice/c_unity/cmptblty/msupdate.htm

  * Please note the useful answers

• Wirless VLAN and DHCP

  I am trying to configure my Aironet 1121 G acess points with several VLANs, got the VLAN everything works great with wired devices, but wireless devices don't you DHCP.

  Basically I have the BVI on my virtual LAN management and two other vlans that cross, try to have the public WiFi on 1 vlan and the two VLAN corporate with separate wifi. Impossible to get IPs on any of them though.

  Vlnas are moved by a catlayst 3550 with addresses of assistance set up on all the VLAN interfaces.

  DHCP comes from 2 boxes of windows on another virtual local network Server 2003

  any ideas?

  Hello

  If I understand, you have plugged your access point to one of the L2 switch. I suggest you to set up your L3 (tandem switch) with pool dhcp to obtain the ip address for vlan respective first.

  To set the dhcp pool in your L3 192.168.2.1.

  create interface IVR and IP address assignment for the VLAN respective (which will act as a gateway of the vlan respective)

  Repeat the same for all the VLANS.

  Create the DHCP pool for the vlan respective and router by default with the ip address of L3.

  AccessPoint#configure terminal
  
      AccessPoint(config)#interface dot11radio 0
  
      AccessPoint(config-if)#ssid .......give the name of your ssid
  
      AccessPoint(config-if-ssid)#vlan ?
  
      AccessPoint(config-if-ssid)#authentication open
  
      AccessPoint(config-if-ssid)#end
  
      

  AccessPoint(config) interface fastethernet 0.30
  
      AccessPoint(config-subif) encapsulation dot1Q 30
  
      AccessPoint(config-subif) exit
  
      

  AccessPoint(config) interface dot11radio 0.30
  
      AccessPoint(config-subif) encapsulation dot1Q 30
  
      AccessPoint(config-subif) exit     

  Check if you have the ip address for the customers.

  In case await you get the IP address of your external dhcp server...

  try to give below command on each respective dot11Radio 0 subinterface "helper-... to give the dhcp server ip address here"

  Please let me know if it works...

  Thank you

  Vinod

• SGE2010 switches, VLAN and a port blocked by spanning tree

  People,

  I have 2 groups of switch.

  SGE2010 2 with VLANS is defined as 10,20 and 30

  VLAN 10 is the management VLAN and it uplinks to our border router.

  VLAN 20 is the workstation VLAN, and all workstations are pointing to the switch as their default GW

  VLAN 30 is the ip phone VLANS, and all phones use this as a gateway.

  I have a GAP between the switches said, we have a few servers on the ip phone switch that must be accessed by the clients of the workstation and the unique link of 100 MB through the router probably won't be enough.

  If I understand correctly, because the switches have different networks on them, a simple shift will not work. I did create a gap and addresses on each side, but it does not appear in this mode, I can block vlan 10 transit to the LAG, with this block I'll end with a logic loop and spanning tree will block the uplinks or LAG itself.

  I have attached a picture with a diagram of our current put in place.

  Any help/advice would be much appreciated.

  John, the 802 standard. 1 initial q indicates there isn't only global tree covering weight independently of belonging to a vlan. It's why you run into problems. Cisco has developed PVST to run on circuits of the ISL. BPMH was originally defined as 802. 1s, which is a combination of 802. 1 q + RSTP. The 802. 1s were later modified to become part of the 802. 1 q.

  The person is incorrect, because they cite "because spanning tree is construction by vlan. They are incorrect, because you have to set the properties of tree cover to allow the spanning tree protocols by vlan. Small business switches do not support the owner Cisco PVST and PVST +. However, the SB switches support BPMH which is a standard of the IEEE.

  How works the BPMH, it's that you have called proceeding, i.e. each construction covering tree. Then you have the region, SB switches support only 1 region. The region maintains the instances. Basically how it works, you activate the EMU at the global level. Then, you specify the instance. As an example, the vlan 1 is instance 1. VLAN 2 is 2.  This will allow you to run 2 physical wires between switches vlan different without looping. If you use classic STP or RSTP, the least costly path will go to the State to block/cast who works as expected.

  -Tom

• Several VLANS and DHCP relay on two stacked switch SGE2000-G5

  We were put to the task of securing a small desktop system managed that is currently set up with a standard switch for each of the offices (with different companies) to see each other and in some cases, access to each of the other documents on the network.

  Obviously, this is far from adequate set up and our goal is to isolate each office using VIRTUAL networks, but share a common internet connection provided by managed offices.  We have two switches for layer 3 Cisco SGE2000-G5, but we are new on Cisco equipment and VLAN, so we are not quite sure on how to implement this.  DHCP must be provided by a router, there is no server.  We are open to suggestions on the router as we still buy a.

  I hope that someone may be useful.

  Thank you very much

  Jim

  Hi Jim,.

  SGE2000 switches you are using must be able to handle this without issue. What type of router you are using? As long as you have a router that will take in charge VLAN / several subnets, it should be a simple configuration.

  Here's a quick run down of the measures to be implemented. (using vlan1 and vlan2)

  On the router, create a vlan / subnet 2 and set the port to connect to your shared resources with the two VLAN 1 and 2 switch. (it will be untagged, two will be marked)

  On the switch, create vlan2 and do the same for the port connected to the router. (vlan1 marked and tagged vlan2)

  Now for each switch port that you want to assign the port access and vlan1 and vlan2. (this vlan will be without a label)

  If your router allows, disable routing inter - vlan. If this isn't the case, you must create rules to block traffic from one network to the other.

  All this happens under the assumption that your router can support VLAN and can also make DHCP for this VLAN.

  Hope this information helps

• VLAN and the SSID does not not in the Web Interface

  We have a couple of APs which do not show the VLAN and via the web interface of AP SSID.  If you go to the SSID Manager page in the web interface, the page rises but doesn't show any SSID configured.  It goes the same for Services - Vlan.  This page appears but does not show in any VLANS configured.  If you telnet to the APs, you see the mssid listed and all the SSID interfaces.  The SSID on the access point is functional and working.  It is just so hard to use the web interface for these APs.  I tried to compare configs running on APs where the web interface does not show this and APs that it shows, but cannot see any differences.

  Thank you.

  Have you tried with different browsers?

  Nicolas

• Create a vlan and conf coelio

  Hello

  I need create 2 VLAN (vlan 10 and vlan 30) to the Cisco 300 series switch.

  VLAN 10 must be default VLAN (no tag).

  After that I wish to associate VLAN10 1 and 2 to 30 port of VLAN. The two ports must be access.

  If anyone can give a step by step to do this?

  Best regards.

  Hi Andre,

  Make a fiour minute video to show you how create two VLANS and I think answering your question.

  After making the changes, I suggested, be sure to save the configuration to the switch.

  (the audio is dead as I began to save the running configuration to the startup configuration)

  In addition, it is not stated clearly, but in the page of "port of VLAN" make sure that you select go after selecting a VLAN to change. See the go button circled in the screenshot below.

  Click here to view the 4-minute video or on the link below;

  https://ciscosales.WebEx.com/ciscosales/LDR.php?at=PB&SP=MC&rID=51454237&RKEY=4f26434b104275a8

  Best regards, Dave

  

• Mapping VLAN and probe Inline

  Hello

  I'm doing all my traffic flow of SSL VPN clients through a traffic Inline probe. From what I see, I should use the mapping feature VLAN. But I can't understand how the function works. ASA not very informative or extensive documentation.

  Currently my ASA has a network of interconnection on a VLAN to my router base, and all my internal network is routed to the base IP address. Default gateway of the router of my Core is the ASA. My ASA provides IP addresses to remote VPN SSL clients and is the default router for them. Remote traffic follows the remote client to the ASA, then through the interconnection to my internal networks. My only ASA works as my perimeter firewall and SSL VPN concentrator.

  I have map VLAN undestand will make all traffic from the remote clients to abandon the vehicle on a VLAN individual. So, I created a new VLAN and that added to a trunk on the SAA. Then I activated "restrict access to VLAN" and set it to my VIRTUAL LAN. My traffic Inline probe is connected to the VLAN and can provide DHCP.

  If it were a classic network, I'd Inline traffic probe the gateway by default for this VLAN and provide IP addresses and gateway with its DHCP server. But how does it work with ASA? I can in captivity the evacuation to this VLAN, but cannot find a way to make the traffic passes through the screen. As ASA does not support routing based on the source can't make the jump next to the probe traffic.

  I can do the bridge of the probe (L2) network for interconnection and the remote client VLAN. But the IP address of the ASA on the VLAN does not fall within the same range as the interconnection, so I can't understand if and how it worked.

  Can someone help me with the configuration or explaing me better how works the mapping VLAN?

  Thank you.

  What you are trying to reach is configurable through the "tunnel" default route, and it would force all traffic of VPN with this default route special.

  for example:

  If your traffic probe Inline between the ASA inside your heart and the interface, you can configure:

  Route inside 0.0.0.0 0.0.0.0 in tunnel

  Requiring all VPN traffic route to IP CORE that would go through your online traffic probe

  Here's the order for your info reference:

  http://www.Cisco.com/en/us/docs/security/ASA/asa83/command/reference/QR.html#wp1840612

  Hope that helps.