vMotion works between HP DL380 G7 and the Gen9

Similar Questions

• vMotion works only in a switch and the management

  Okay, I reconfigure my network in all of my 3 guests. I had vMotion (via VLAN50) in a vSwitch dedicated using binding rising vmnic0. vMotion between hosts has worked well. It looked like this...

  

  I want to spend vMotion for a vSwitch shared with the management network. So I deleted the vSwitch2 vmnic0 and added to vSwitch4. Then, I created a new port group for vMotion with a new IP address. See below.

  

  In vSwitch4 properties, the management network has vmnic7 as active and vmnic0 as the day before. vMotion is set in front of it. The vSwitch is configured to load balance from the originating virtual port ID.

  vMotion does not work between hosts and gets stuck at 14%. I get a timeout between 10.10.50.70 and 10.10.50.71 (another host).

  I don't know that my physical switch is configured correctly. I have two ports accepting traffic on the management and vMotion VLAN. If I pass around the allocation of vmnic (sort of management use vmnic0 as active and vmnic7 as before) then I can still ping the IP management. Also, if I move back to vSwitch2 vmnic0, vMotion starts working again so I guess I'm missing something on the side of ESXi.

  What Miss me?

  Thanks in advance

  OK, problem solved. The webex engineer had in my screen and start troubleshooting this.

  First of all, vmkping he had the IP address of the new IP address of vMotion to another host, that has failed. Then, he ran 'esxcfg-vmknic - l' and noticed that the old port vMotion group was always enabled. In the graphical interface it has disabled this by going into the properties of the vSwitch2 > vMotion port group and checked the property of vMotion. Then run vmkping, but it has always failed. Back in the GUI, he removed the vSwitch2 completely. Ran vmkping and it worked.

  He assumed the problem was vMotion was trying to communicate through the old switch, in spite of remove me the adapters and the engineer vMotion traffic on the port group in this deactivation switch. It is useless for me to keep the old vSwitches, except as a back fall where vMotion failed. Seems I should have been more courageous and just removed them when I was creating the new vSwitch.

• In the latest version of MF, there is a missing button, who was in the previous version: between backward/forward buttons and the bar hits there was little flash, who showed a few recent pages I just went through. How can I restore it?

  In the latest version of MF, there is a missing button, who was in the previous version: between backward/forward buttons and the bar hits there was little flash, who showed a few recent pages I just went through. How can I restore it?

  If you mean the drop marker so you can always get history buttons front and rear, if necessary by left clicking and for a second, or by right-clicking on them.

  If you want to continue the brand drop there too there is that Extension to https://addons.mozilla.org/en-US/firefox/addon/backforward-dropmarker/

  Also the abbreviation for Firefox is Fx

• Are there differences between Windows 7 OEM and the commercial full version?

  Are there differences between Windows 7 OEM and the commercial full version?

  Commercial versions include two disks installing 32 and 64 bits and can be moved to new systems.

  OEM versions are either 32 or 64-bit - only installation disc is included - and cannot be moved to a new system.

• I want to install a trial version of indesign CC but the username and password does not work. Is my username and the same password I use to connect to Adobe?

  I want to install a trial version of indesign CC but the username and password does not work. Is my username and the same password I use to connect to Adobe?

  I work on a Mac computer

  Hi Tania,.

  He could be induced to Mac username and password.

  Kind regards

  Sheena

• Thunderbird does not work after installing Win 10 and the mobile profile of Win 7

  I've installed Tbird 38.3.0 on a new Dell computer with Windows 10 on this (8 GB of RAM, 1 TB harddrive). I then followed these steps to put my old profile from the old computer to Windows 7:
  1. copied my profile on the Windows 7 computer on an external drive.
  2 installed Tbird on the new computer Windows 10 38.3.0, but has nothing to do with it.
  3. following the instructions on the site of Thunderbird on the displacement of a profile:

    a) Use the Profile Manager to create a new profile on the Win 10 computer.
    b) Copy the profile from the external drive to the new profile folder
    c) Use Profile Manger to tell Tbird to open the new profile
  

  4. start Tbird.

  I see my files with email in them, but there are problems:
  1. None of the Tbird dialog boxes open when I choose a command in the menu bar (including the new Message).
  2. I can't get Tbird to display the contents of a folder in the Home tab. There is only the accounts and the advanced features of the Inbox, display in the right pane, next to the folder tree. The only way to see the contents of a folder is right-click and choose open in a new tab.
  3. when I click or double-click on a folder, the contents of the file does not replace the previous folder. TBird on the Windows 7 computer, clicking a folder displays the contents of the new folder.
  4. sometimes when I Alt + Tab of Tbird, then Alt + Tab, moving the cursor of the mouse on the messages in the Inbox tab causes the message object, Date,... to disappear, leaving blank lines.

  I tried to uninstall Tbird and reinstall it, but this does not solve the problem.
  I tried to reboot Windows 10 but that does not solve the problem.
  I don't seem to be able to download email and preview in the messages pane, but I can't open it in a separate window.

  A lot of people seems to be able to run Tbird on Win10, so it should work. Any ideas on why it does not work and what I can do about it?

  Thank you very much in advance!

  go to add-ons.
  remove the addon of lightning.
  restart - everything should be good.
  If you still need the addon of lightning, install it again - it should give you a new version.

  Please tell us that all is well

• Firefox between information in research and the location of connection as if the SHIFT key is down.

  When you enter in the search bar, bar website or a website login Firefox acts like the "shift" key is pressed to prevent that information to register correctly.

  Hi Cor - el
  The problem seems to have disappeared with the upgrade to V17.0. It must have been a conflict between my WinXP and V16.0.2 that the problem appeared when the upgrading to V16.0.2 and disappeared with V17.0.
  I have not had the problem with Win7 on another machine.

  I will mark the problem as solved when I have used Fx for a few days and the problem does nor re-occur.
  

  Thanks for your help.
  With respect to Peter Dalton

• What is the difference between Windows 7 OEM and the retail version of Windows 7?

  Can someone tell me, what is the difference between windows 7 OEM and sales vs retail?

  On Thu, 20 Sep 2012 19:56:47 + 0000, STEVE-5 says:

  Can someone tell me, what is the difference between windows 7 OEM and sales vs retail?

  There is no difference in the product itself.

  Although if you get a generic OEM full version, it contains the
  even software, it has the following disadvantages compared to the
  commercial version:

  1. the biggest drawback of an OEM version (at least in the USA) is
  that its license it permanently binds to the first computer, it is
  installed on. He can never legally be moved to another computer, sold,
  or given (except with the original computer). If the computer
  dies or is stolen, your license dies with him.

  2. he can't do a clean install, not an upgrade.

  3 Microsoft offers no support for OEM versions. You cannot call their
  with a problem, but rather to secure the necessary support of your
  OEM; who take in charge may go anywhere between property and non-existent. Or
  You can get support elsewhere, like in these forums.
  Ken Blake, Microsoft MVP

• Integration between Oracle apps R12 and the MySQL server.

  Hello

  We got a requirement to integrate between the oracle database and the MySQL server.

  Payroll run in the Oracle Apps R12 and the need to develop an API to insert data of payroll results in MySQL database tables, it will be for 4.5 months as finance Modules of Apps will also apply for them, so that MySQL will be totally replaced by Oracle.

  Please suggest how to start integration, as it's my first time.

  I went through a document online, but it says 'updates, removal or insertion may fail' using the gateway dg4odbc, need to use 'different gateway called DG4MSQL, which requires the purchase of new licenses.'

  Thank you very much in advance.

  Kind regards

  Afzal.

  Afzal,

  As mentioned in your message, you must use DG4MSQL which requires the purchase of a new license.

  How to set up DG4MSQL (Oracle to MS SQL Server database entry door) 64-bit Unix OS (Linux, Solaris, AIX, HP - UX) post installation (Doc ID 562509.1)

  How to set up DG4MSQL (MS SQL Server database gateway) on a 64-bit Windows post install (Doc ID 1086365.1)

  How to troubleshoot common errors encountered when using the gateways of the database (DG4IFMX, Dg4MSQL, DG4SYBS), DG4ODBC or generic connectivity (Doc ID 234517.1)

  How to set up DG4MSQL (gateway to Oracle to MS SQL Server database) exit 11 on Linux x 86 32-bit post installation (Doc ID 437374.1)

  Thank you

  Hussein

• Exadata - any changes in functionality between V2 / X 3 and the ESS/RDBMS?

  All,

  We are running a quarter V2-rack on 11.2.0.2 BP7 and 11.2.2.3.2 ESS. We're heading to a quarter-rack 3 X little which runs to regardless of recent older versions and the RDBMS/GI/ESS.

  We use on our current Production environment, of hepatocellular carcinoma and discovered that with bitmap indexes (which we have a lot), it was necessary to disable the index, perform the HCC compression on the table and then rebuild the index later.

  
  

  Obviously, an operation very intense when we have HUGE clues.

  
  

  Anyone know if this same behavior in 11.2.0.3 ESS RDBMS/more later? We are always forced to disable the index before run us HCC on the table or have the relationship between the index bitmap and HCC cooled a bit?

  
  

  Mark

  Hi Mark,

  You will get probably may 2013 11.2.0.3.18 (RDBMS) on 11.2.3.2.1 (ESS).

  You can find some details in 888828.1 (or follow link https://updates.oracle.com/Orion/Services/download?type=readme&aru=16223374) to find what has been corrected.

  Kind regards

  Tycho

• Difference between file system capacity and the capacity of the disks in Capacity Planner reports

  Hello

  I had to go on my Capacity Planner tool training soon, but I have a question on the front that frustrates me. In the evaluation report that comes out of the tool after the analysis, a use of disc section, which lists all the servers for analysis there. A column of this report is directed to file system capacity, another disk capacity. In all cases, the first is less than the latter. What is the exact meaning of these labels?

  Some of the numbers differ substantially between the columns, for example 20 GB for a capacity of 36 GB of disk space for a server and file system. He said that only 20 GB to 36 GB disk is formatted/partitioned to use?

  As previously stated:

  Disk capacity is 36 GB - physically, there are 36 GB of storage.

  File system is logical capacity - the amount of space used by files on the disks.

  File system and the capacity of the disks will never match because fees General table of file.

  I hope this helps.

  -abe

  INTEGRITAS!

  Abe Lister

  Just a guy who likes to virtualize

  ==============================

  Won't lie. I like points. I mean, if something useful for you, consider slipping a few points for him!

• The quarters between a bullet point and the text really

  I'm sure I've done this before, but can't remember how. I have a list of bullete (ul) and would like to leave a wider space between the chip and the beginning of the text. I tried to play with the padding and margins, but which moves the text and bullet point.
  I guess that things thinking it can be done...?
  Andy

  Good read through:
  http://alistapart.com/articles/taminglists/

  --
  Concerning

  John Waller

• Why Windows high contrast doesn't work anymore since Firefox 29 and the theme of the Australia?

  In firefox, 28 and all versions before that when I had Windows High Contrast active firefox would also be in high contrast. This would make black Web pages and all the text would become white. Because of my disability which makes it much easier for me to see and walk through it. Since firefox 29 and the introduction of the Australia theme but it seems like a high contrast in windows is no longer supported by firefox. That's why I went down to firefox 28 in order to be able to navigate as I used to.

  There is a hidden value that needs to be modified in two places:

  Go to Options > content > fonts look and colours, click on 'Advanced' > uncheck allow sites to choose the fonts and colors
  AND
  Click on ok and the color... on the content page > uncheck the allow pages choose own colors other than above. Make sure that the background is black and white choice policies.

  Under windows if you have high contrast mode, please also try "use system colors".

• my sound jumps and comes in and out in a game, but works very well for music and the moveis and things like that it's just the fact that in games

  sound

  Hello

  How can I stop my music skip or break down when I play?
  http://windowshelp.Microsoft.com/Windows/en-us/help/36db5c82-9247-4346-909a-f87743b653ae1033.mspx#EFC

  1. right click the icon of speaker near right lower clock - peripheral of reading

  Highlight speakers - properties (right same low page) - tab improvements - check Disable all sound effects
  Apply - OK

  2. check the configuration - Device Manager - sound, video and game controller

  Note name and complete model of the audio device - full decription - now double click it.
  Driver tab - notice the driver version. Then click on set to update driver (maybe nothing like MS is far
  behind the pilots of certification). Then right CLICK on the device - UNINSTALL - REBOOT - it will refresh
  the driver stack.

  Now go to system Maker and look for the updated drivers (or get the same if no new) it will be
  your rescue. Download - SAVE - go to where you put it-RIGHT click in it - RUN AS ADMIN

  Then do the same for the manufacturer of the device (like Realtek or who made the device).

  NOTE: Often restore audio drivers to check the version after installing and restarting is
  see if the version you have installed is there, otherwise repeat the installation - restart until it is. This may take
  several tests according to the recommitments how much he makes.
  
  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Difference between Horizon 6 Advanced and the company of 'unified portal' and Horizon 6 workspaces

  Can someone do a bit of explanation for the following:

  I am you are looking to understand the use of terminology in marketing and how it fits into the picture.

  Terminology:

  Workspace - VMware

  VMware workspace - Horizon

  Workspace Portal - VMware

  -Unified Workspace

  With the following references

  • "Portal Workspace 2.0"VMwarefiles Horizon feature is deleted ' VMware Workspace Portal 2.0 Release Notes
  • VMware Horizon workspace (notice the data sheet is still published but is a bit outdated)http://www.vmware.com/files/pdf/workspace/VMware-Horizon-Workspace-Datasheet.pdf
  • "Access to files and Applications from anywhere.

  AND the use of the terminology "unified workspace.

  What the "Unified Workspace" such as described in the "VMware workspace" link below different described also in the same document?

  http://www.VMware.com/files/PDF/products/horizon-view/VMware-horizon-view-pricing-Licensing-FAQ.PDF

  They seem to be different that the ability to share files is available under "VMware workspace.

  There is good documentation on the item "VMware workspace.

  http://www.VMware.com/files/PDF/Techpaper/VMware-horizon-workspace-reviewers-guide.PDF

  http://pubs.VMware.com/horizon-workspace-10/index.jsp#com.VMware.HS-install.doc_10/GUID-71C2045E-2934-4D87-A597-E82B2BE88B2C.html

  But I can't find documentation on "Unified workspace" limited the video below speaks of a 'unified workspace", but has pictures showing"VMware workspace.

  https://www.YouTube.com/watch?v=2SstavM0r9A

  More specifically,.

  -Are they a portal with the various components of license?  (I guess that's the case, but the documentation is very limited)

  -They are two different portals?

  If they are two different portals how both are integrated?

  Help appreciated.

  Hi Sean.

  I can understand that it can be confusing, a lot of changes has been done in recent years.

  The Horizon workspace file-sharing component were interrupted from Horizon Workspace 1.8.2 will finally be replaced by Airwatch Secure Content Locker.

  I'll try to answer your questions:

  1. - are they a portal with the various components of license?  (I guess that's the case, but the documentation is very limited)

  1. A: Yes, there is a single portal.

  2 - they are two different portals?

  2a: no, there are not two portals.

  3. If they are two different portals how both are integrated?

  3 A: there is only a single portal.

  4. how the "Unified Workspace" such as described in the "VMware workspace" link below different described also in the same document?

  4 A: its the same, it's just a way of describing the feature.

  Linjo