VMS IPS MC 2.2 2.3

Similar Questions

• Cannot start IPS MC in CiscoWorks VMS

  Hello

  I just started getting error (on a pop up Applet), below when I try to run the IPS MC in CiscoWorks VMS.

  +++++++++++++++++++++++++++++++++

  You are not allowed to request the action associated with screenID:

  "/ s510.

  ++++++++++++++++++++++++++++++++++

  Any ideas?

  Run version 2.2.

  Thank you

  Naman

  Do you use GBA or another server authentication to authenticate/authorize the sessions? try to delete the ACS of VMS authentication and try again. The error message is related to an authentication problem. You must also close all your browsers and reopen then.

• Recommendation of the IPS

  Hi Netpros,

  I want to implement the IPS solution in our company as well as management software to manage mailboxes of the IPS. What is the latest version of the Cisco management software I have to deploy. It will be compatible with the ID?

  Thanks in advance.

  You can implement 2.3 VMS of Cisco who has the CiscoWorks Center for IDS sensors

  For more information, please visit http://www.cisco.com/en/US/partner/products/sw/cscowork/ps2330/products_qanda_item09186a008009253c.shtml

  It may be useful

  Franco Zamora

• Action of VMS to block host or network

  We use to monitor the IP Monitoring Center security 2.1 addresses. VMS SecMon 2.1, there is an action to block a host or a network by right clicking on the host affending.

  According to the documentation for secmon viewer "blocking a host causes a sensor to block all traffic from the source IP address associated with the selected event.» Similarly, blocking a network causes the sensor to block all traffic from the network that contains the source IP address of the selected event. Blocking is done through a properly configured Cisco router. »

  Ref: http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/cw2000/mon_sec/secmon20/ug/ch04.htm#wp322382

  We have installed an inline IPS using a pair of vlan.

  I would like to be able to refuse an attacker online manually by clicking an action of VMS SecMon but when I use the blocking action, that the host is always allowed. It seems that this action cannot run that by setting up a blocking device. that is a Cisco ios router or a pix. This statement is correct?

  Is it possible the console of VMS for telling the IPS to refuse an attacker host or network by ordering manually to make in the same way the blocking is done?

  The action will work by setting up a blocking device.

• Security 6.0 of IPS monitor

  6.0 sensors will work with SecMon? And please don't tell me that I will be forced to use CS MARCH. So there will be an update SecMon so that he can work with 6.0?

  Followed SecMon of an IPS version 6.0 has been tested. The existing version of SecMon can follow HIPS 6.0, but shows only the fields in the alerts that existed in IPS 5.1. SecMon does not display the new fields that are visible only in IPS 6.0.

  Also understand that the MC corresponding IPS does not support IPS 6.0.

  SecMon and IPS MC are part of virtual machines.

  VMS has been replaced by the CSM.

  The current version of the CSM is not able to configure IPS 6.0; a new version of the CSM will be published next year that will support the configuration of a sensor IPS 6.0.

  CSM does not include a utility for displaying IPS alerts. So for the display of the IPS alerts you will be either must continue to use SecMon of virtual machines, or use VEI, or visualization tool alert another.

  At the moment there is no plan to change the SecMon to support the new fields in IPS 6.0 as VMS has been replaced by CSM which does not SecMon contain.

  SecMon can be used to monitor a sensor IPS 6.0, but only displays the fields that were available in the 5.x sensors.

  NOTE: You have no place to report without delay to the IPS 6.0. Version 5.1 of IPS will continue to receive updates of the signature for at least another year and probably still a year and a half or more.

• Look at a FPS in real time of the events of several IPS devices

  What is the best strategy for the display of the IPS in real-time of the events of several IPS devices now that VMS filed end of LIFE?

  There was a nice view unique of all IPS events from all IPS devices run in VMS and I was wondering where I can tell people to receive the same information on their networks. I do not see in CSM and I do not think that they will find in MARCH. Please notify and correct me if I'm wrong. Thank you!

  You can use VEI. It is an observer of events that has a dashboard in real time also. You can import several sensors inside and view the events in real time.

  Link to VEI to 5.x versions:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/IPS-EV

  Link to VEI to versions 4.x:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/IDs-EV

  Kind regards

  Maryse.

• IPS sensor - Event Notification by e-mail?

  Good day to all.

  I was asked to recreate some features after he lost the customer improved VMS to the CSM but without CS-MARCH or any other event monitor. The user has had the system to generate an email when an event was triggered. He was apparently noisy initially but after setting wasn't a bad solution. No one knows how he was initially put in place but I can only assume it is the method that is described in the Cisco document to: http://www.cisco.com/en/US/customer/products/hw/vpndevc/ps4077/products_configuration_example09186a00801fc770.shtml#fivesensor

  Now, however, since the CSM has not received the event data is it possible to recreate this process of "notification"?

  Are using CSM 3.02 and the sensors are still at 5.14. The sensors will be updated to 5.17 later today. I will then either be upgrading the client to the latest revisions and service to CSM or rolling packs to the VMS depending on whether I can get notifications to work with MSC.

  NOTE: They order a CS-MARS appliance with the conviction that it will solve the problem, but as the last word, it will be several months at least before they could get it. I'm afraid that CS-MARS will NOT give back them this feature. Can you confirm/deny?

  Finally - CSM does not include a security monitor, as did virtual machines, and CS-MARS not really recreate that kind of view or the management of the events - what solutions are there to reproduce the functionality of the Security Monitor? Are there? Is-CS-MARS the new bully on the block?

  Since the client is to stay at a 5.1 version, then you have 3 options:

  1) down to virtual machines and continue to use the Security Monitor

  2) stay with the CSM and buy CS-MARCH for the monitoring of events. CS-MARS should provide the ability to e-mail notification.

  3) stay with the CSM and installing and using VEI 5.2 (1).

  VEI 5.2 (1) can be installed either on a separate machine from the CSM as a stand-alone utility:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/IPS-EV

  VEI 5.2 (1) contains the new alerts e-mail notification feature.

  GOLD VEI 5.2 (1) can be installed as part of the installation of CSM (I know it's in the CSM 3.1, but don't know about previous versions of CSM).

  Here are a few documents on the execution of the IEV 5.2 (1) in the CSM framework:

  http://www.Cisco.com/en/us/partner/docs/security/security_management/cisco_security_manager/security_manager/3.1/user/guide/monidiag.html#wp1203768

  NOTE: VEI 5.2 (1) is targeted for use in networks with sensors of 5 or less. When running with 5 sensors or more, then CS-MARS would be the veiwer advised.

  When the user later upgraded to version 6.x, then option 1 (downgrading to virtual machines) is no longer an option and option 2 or 3 would be required.

• Change of storage iSCSI IPs

  Hello

  We will be consolidating the 2 sites in one soon, and in the context of that we'll have the blades moving and storage iSCSI from one site to the other and re - IP them in the process.

  That's what I had in mind, please let me know if Miss me something:

  -Stop everything and moving equipment

  -Fuel storage iSCSI and re - IP

  -Power of blades and change their IPs

  (at this point all data warehouses and virtual machines on show them also inaccessible)

  -Add the IPs blade storage unit to allow access

  -In storage adapters / iSCSI / dynamic discovery, remove the old storage IPs and add new IPs, rescan storage

  Here, we should have our data storages and all VMs back on their show normal, that we should be good to start turning on VMs.

  Anything I missed? I did similar work a few times, but not in the last year or so, just wanted to do a validation test. We lack ESXi 4.6 build 1050704.

  Thank you

  If it worked very well, just as described above. I have to award points to myself :-)

  Thank you

• VMs ESXi access remotely via internet

  Hi all

  I have 6 virtual machines on my ESXi running SharePoint 2007 / 2010, SQL Server 2005 and 2008 and AD.

  My ESXi server is connected to my DIR-615 wireless router, and I have access to my ESXi server with vSphere Client wireless to my laptop.

  Also, I use DRC remotely access my VMs from my laptop as well.

  I want to access my virtual machines remotely from outside my home, but I can't get any step by step instructions from anywhere on the net.

  Currently, I have registered with "dyndns.org" and can access my router only from outside. I think that what is left is port forwrding

  which turns out to be hard to do.

  Should what ports I use? No one redirects me to guide the user, blogs or articles on how to do this?

  Thank you

  A few options.

  (1) port transfer all incoming traffic for the wireless router DIR-615 to a running VM firewall on ESXi and then have this firewall VM give access.  Or you can simply configure the router to port forward to a VPN server.

  (2) place a switch between the wireless router and the device of the ISP.  Create a new vSwitch on ESXi with a free NETWORK card and NETWORK card to connect to the switch.  Create a VM on ESXi firewall that is connected to the new vSwitch and your existing LAN vSwitch.  The new vSwitch will have access to the internet and if your ISP allows multiple public IPs you can then configure VPN services on the firewall VM or port forwarding for RDP to the appropriate host.

• Problem in the establishment of the IPs of various NICs through Set-OSCustomizationNicMapping

  I need to create multiple VMs to Linux from a few different models and I would use a customization specification profile. The VM model has 3 NIC in 3 different VLANS, the 3rd is not suppposed to have a default gateway (which is not my main problem). Cloning via vCenter works, after I provide the IPs 3 virtual machine is cloned correctly.

  However, this script, I try this code:

  $custSpec = get-OSCustomizationSpec "D1 RedHat | New-OSCustomizationSpec-name "xyz".
  $custSpec | Get-OSCustomizationNicMapping | Game-OSCustomizationNicMapping - IpMode UseStaticIP-position 1 IP address - 10.70.236.99 - mask subnet 255.255.255.0 - DefaultGateway 10.70.236.1
  $custSpec | Get-OSCustomizationNicMapping | Game-OSCustomizationNicMapping - IpMode UseStaticIP-position 2 - IpAddress 10.70.237.99 - mask subnet 255.255.255.0 - DefaultGateway 10.70.237.1
  $custSpec | Get-OSCustomizationNicMapping | Game-OSCustomizationNicMapping - IpMode UseStaticIP-position 3 - IpAddress 10.10.10.99 - mask subnet 255.255.255.0 - DefaultGateway 10.10.10.1
  $custSpec | Get-OSCustomizationNicMapping

  gives some problems with PowerCLI 4.1U1. The first Set-OSCustomizationNicMapping command sets the IP address correctly, but the 2nd and the 3rd gives:

  Game-OSCustomizationNicMapping: 14/04/2011-16:23:10 Set-OSCustomizationNicMapping the Posiotion of the object property has changed. This property represents a portion of the Id of the object, so this operation is ambiguous. Please get the new object and run the operation.
  At line: 1 char: 74
  + $custSpec | Get-OSCustomizationNicMapping | Game-OSCustomizationNicMapping < < < < - IpMode UseStaticIP-position 2 - IpAddress 10.70.237.99 - mask subnet 255.255.255.0 - DefaultGateway 10.70.237.1
  + CategoryInfo: ResourceUnavailable: (:)) [game-OSCustomizationNicMapping], VimException)
  + FullyQualifiedErrorId: Client20_ObjectVersionService_VerifyIsCurrentVersion_ExpiredObject, VMware.VimAutomation.ViCore.Cmdlets.Commands.SetOSCustomizationNicMapping

  and the profile of customization is set to:

  SpecId Position IPMode IPAddress DefaultGateway
  ------ -------- ------           ---------       --------------
  XYZ 1 UseStaticIP 10.70.237.99 10.70.237.1
  XYZ 2 UseStaticIP 10.10.10.99 10.10.10.1
  XYZ 3 UseStaticIP 10.10.10.99 10.10.10.1

  When there are:

  SpecId Position IPMode IPAddress DefaultGateway
  ------ -------- ------           ---------       --------------
  XYZ 1 UseStaticIP 10.70.236.99 10.70.236.1
  XYZ 2 UseStaticIP 10.70.237.99 10.70.237.1
  XYZ 3 UseStaticIP 10.10.10.99 10.10.10.1

  Why it gives the above errors and that's why changing the IPs incorrectly?

  Thanks in advance.

  Hello

  This behavior is by design. Here is the explanation:

  Cause:

  1. misuse of command
  

  ' Set-OSCustomizationNicMapping - Position' sets the posiotion of the nic past mapping object.

  The following call assigns consecuently the posiotion three objects to map nic 1:

  $custSpec | Get-OSCustomizationNicMapping | Game-OSCustomizationNicMapping - IpMode UseStaticIP-position 1 IP address - 10.70.236.99 - mask subnet 255.255.255.0 - DefaultGateway 10.70.236.1

  2 locking mechanism

  So lets have the mapping objects following nic

  1 mappingA

  2 mappingB

  3 mappingC

  If you keep the reference to A and B and change the posiotion c and 1st then the references of the A and B will expire and you will no longer be able to edit them with this old references. The reason behind this is the unique identifier of A and B, we know is their position and this ID has changed--they became the 2nd and 3rd. So to change the old references with bad identifiers may cause problems only. That's why we have implemented the locking mechanism and you have to get the nic mapping objects to change.

  Solution:

  $custSpec | Get-OSCustomizationNicMapping | où {$_. {Position - eq 1} | Game-OSCustomizationNicMapping - IpMode UseStaticIP - IpAddress 10.70.236.99 - mask subnet 255.255.255.0 - DefaultGateway 10.70.236.1
  $custSpec | Get-OSCustomizationNicMapping | où {$_. {Position - eq 2} | Game-OSCustomizationNicMapping - IpMode UseStaticIP - IpAddress 10.70.237.99 - mask subnet 255.255.255.0 - DefaultGateway 10.70.237.1
  $custSpec | Get-OSCustomizationNicMapping | où {$_. {Position - eq 3} | Game-OSCustomizationNicMapping - IpMode UseStaticIP - IpAddress 10.10.10.99 - mask subnet 255.255.255.0 - DefaultGateway 10.10.10.1

  I hope this will help.

  Thank you

  Nedko

• 24 IPS monitor envy: display of 24 issues looking

  I have a monitor of the Envy 24 IPS with display problems.  It seems "cloudy" and there is a line thick pronistique coming down in the middle.  I hung it on my iPad and had the same display issues.  Factory reset already have.  Any help appreciated.  I had the monitor, less than a year and it's been great until recently.

  Good to see that you will get a replacement.

• his IPS LED backlit screen 27vc: could not find a way to mount 27vc 27 "IPS LED monitor

  I recently bought the 27 "and 22" HP vc IPS LED backlit monitors. My intention was to mount them on a mount for two monitors that clips to the back of my desk or on the wall. Every company in the world sells the same media/materials for double monitors, but all have the traditional media that has 4 screw holes. Vc monitors do not have the ability to accept this type of Mount. I tried to call HP customer service and am redirected more than 5 times to the representatives who had no idea how mount it and didn't have an adapter. It is impossible that it is impossible to mount these monitors. Anyone know of a replacement product or an adapter that I can use to ride together?

  Hello

  HP has monitors with standard VESA mounting holes. My suggestion: take it to the shop and swap for the one that supports standard VESA otherwise must a good skill and a good drill.

  Kind regards.

• Portege Z30 - A - 1E5 IPS Panel only?

  Hi all

  I wanted to ask if the TOSHIBA Portege Z30 A 1E5 is the only Z30 - A with a slab of IPS?
  Also, is it possible to upgrade a GPS module in a Z30?

  Thank you very much
  MIRU

  Portege Z30 - Models are available on the market. Some models are equipped with a touchscreen and a full HD resolution (1,920 x 1,080) and other models are equipped with a non touch common and HD resolution (1,366 x 768)

  For example the Portege Z30-A-192 supports window color TFT LCD with a resolution of 1366 x 768.

  Portege Z30-A-1E5 was equipped with another fire on the side of color TFT LCD IPS display with a resolution of HF Full 1920 x 1080

• Pavilion 22cwa: HP Pavilion 21.5 inch IPS LED HDMI VGA Monitor

  Hello

  I have recently bought HP monitor connected to my laptop and installed the driver.

  My only problem is the annoying icon on the upper right of my screen. It seems that it is a characteristic of the pilot. it disappears when I step outside, but whenever I start my computer it comes back on. (closing is basically software closure of the driver, so he starts each time I restart my computer)

  is there a way to disable this feature?

  

  Hi @CrazyCoder,

  Welcome to the HP Forum! Is a great place to find answers and advice! You have the best experience on the HP forum, I would like to draw your attention to the Guide of the HP Forums. First time here? Learn how to publish and more.

  I understand that you have recently purchased the HP Pavilion monitor and it works well except that you have an icon in the top left that you find boring. This icon is most likely for the my display software. Here is a link to the Guide to the user IPS LED backlit monitors for you to review. You can

  My Display software allows to choose preferences for optimal viewing. You can choose the settings for games, movies, photo editing or just work on documents and spreadsheets. You can also easily adjust settings such as brightness, color and contrast with my display software. You can uninstall the software, if you choose to not use it. If not, you should check the settings in order to determine if there is an option to hide the icon. Please let me know how it goes.

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek. "In addition, by clicking on the" ""Twww.Mountainview.rsb.qc.ca Up ' below is a great way to say thank you!

• How to add a monitor HP Envy 23 IPS to a desire to tilt all in one

  We have a 27-k150xt want tilt all-in-one with the Windows 8.1 operating system.

  How do add us a HP Envy 23 inch monitor IPS P # E1K96-60001?

  Thanks in advance for your time and help!

  Hello

  The HDMI port on the tilt is IN a port. You need something similar to the following device (called USB video adapter):

  http://www.harveynorman.com.au/Targus-USB-3-0-superspeedtm-dual-video-adapter.html

  Kind regards.