Portege Z30 - A - 1E5 IPS Panel only?

Similar Questions

• What is the number of keyboard for Portege Z30-A-1E5 part?

  Hello
  I want the Toshiba Portege Z30 A 1E5, but is apparently available for purchase of the German and Austrian sellers with the QWERTZ keyboard. I would like to buy an and Exchange on the keyboard AZERTY or QWERTY (UK).

  However, I spoke with a company that and they can't confirm that they can get a part unless I can provide a reference number of keyboard (they also cannot give me a quote without it), but this number does not seem to be easy to get their hands on without actually having the computer and take off the keyboard and research under! I feel a little nervous about spending so much money when there's a chance that I won't be able to reverse the keyboard.

  So my question is, can someone tell me what the part number of the keyboard is for the a-z30-1e5 portege?

  Any help would be appreciated!

  Kate

  Hi, Kate

  I m wondering why you want to buy a Portege Z30-A-1E5 that isn't available in the United Kingdom?
  The notebooks are pre-installed with a Windows system in different languages. In the case of Portege Z30-A-1E5 available in Germany, the system language would be German.
  The keyboard also supports a different layout.

  Portege Z30-A-1E5 was equipped with a processor i7, SSD 512 GB and 16 GB of RAM disk.
  Very similar Portege laptop, Z30 - has - 1 6 was released in the United Kingdom. Its preinstalled with the Windows system in the English language and English keyboard layout.
  Of course, the hardware specs are a little bit lower (256 GB SSD drive and 8 GB of RAM) but I think that this could be improved is much easier to replace the keyboard.

  However, where you can buy the Portege Z30-A-1E5, I recommend contacting the maintainer authorized Toshiba in your country for replacement keyboard. Guys could control the keyboard of Toshiba law and could perform the replacement.

  Just a note: the replacement must be performed by service provider authorized because of the validity of the guarantee. The replacement must be performed by an approved engineer to keep the warranty valid.

• Portege Z30-a-1E1 - WIFI connection only 150Mbps

  Hello

  Today, I received my Toshiba Portege z30-a-1e1 running Win7. I've updated all the drivers, firmware and of course Windows itself. Unfortunately the WiFi only connects up to 150 Mbps (router configured to 5 GHz only, 40 MHz wide only, only N and auto channel selection, WPA2 Personal). Other laptops at home are connecting with up to 260Mbps (even 7 Asus F8v). Portrege shows that it is connected with the 802.11n standard.

  Any suggestion that I can do to activate the higher speed connectivity.

  Kind regards
  Blazej

  Hello

  150 megabits per second transfer is not a bad value for 802.11 WLan N standard.
  WLan highest transfer rate depends strongly on factors such antenna Wlan, WLan miniPCI and environment module.

  Wikipedia gives this info on the standard 802.11 N standard:
  … Assuming that the operating parameters equal to an 802.11 network g reach 54 megabits per second (on a single channel of 20 MHz with a single antenna), an 802.11n network can reach 72 megabits per second (on a single 20 MHz with a single channel antenna and ns 400 guard interval); of 802.11n speed can go up to 150 megabits per second, if there are no other shows Bluetooth, oven microwave or WiFi in the area using two channels of 20 MHz 40 MHz mode. If several antennas are used, then 802.11n can go up to 288 megabits per second mode of 20 MHz with four antennas, or 600 megabits per second in mode to 40 MHz with four antennas and 400 ns guard interval...

  http://en.Wikipedia.org/wiki/IEEE_802.11n-2009

  By the way: you can check additional WLan module settings in Device Manager-> properties-> Advanced tab

• Portege Z30 poster ipv4 and ipv6 - only pxe boot is

  Hi all

  Toshiba Portege Z30

  We do all our installs via PXE, when you press F12 I get now two network options where normally I would just get a.

  F12 gives the following options:

  HDD/SSD: SAMSUNG SSD SERIES
  LAN1: IPv6
  LAN2: IPv4

  When I select the option I get what follows read (IP addresses were not included, but are correctly pointing to the right servers):

  ------------------------------------------------------------------------
  > On IPv4 PXE boot.
  IP address of the station is *. ***. ***. ***
  IP address of the server is *. ***. ***. ***
  NBP filename is SMSBoot\x86\wdsnbp.com
  The NBP file size is 30832 bytes
  Download the NBP...

  Succeed to download the NBP file.

  Download the NBP...

  Succeed to download the NBP file.
  Press a key to continue...
  ------------------------------------------------------------------------

  I tried searching through the BIOS settings but can't find nothing obvious

  Can any advise if there is anything I can try to get this laptop to perform a PXE boot please

  Let me know if you need additional information

  Kind regards
  Steve

  Looks like your server isn't aware UEFI.
  Try changing the the CSM UEFI Boot Mode in the BIOS under the Advanced tab, under System Configuration. You may have to disable Secure Boot first.

• Portege Z30 - A - 18 M - what is its display panel technology

  Hello

  My question is: what is the type of technology used Billboard in Portege Z30 - A - 18 M? I guess it can be TN or IPS. While one is?

  According to the specifications of the laptop, the Satellite Z30 - A - 18 M is equipped with a 13.3 "(FHD) 16:9 TFT color LCD (NO CSV) supporting the IPS technology and resolution of 1920 x 1080 pix max

  I hope this helps you!

• Fingerprints on the Portege Z30-A-12 q utility does not work

  Hello

  I need help with this issue:

  I have installed fresh windows 8.1, the same version as before, but this time I chose UEFI on BIOS. When I used the BIOS the fingerprint sensor was working fine, but now it says "unable to connect to the probe.

  I use Toshiba Portege Z30-A-12 q i5-4200 256 GB SSD, or PT243E model. I've searched the forums and found a similar problem with another Toshiba R product that was resolved by adding an exception to the firewall.

  Utility of fingerprinting with the exception of firewall, even disabled firewall all the way, but always the same problem, I added. In Device Manager, I have biometric sensors (WBF) (PID = 0010) validity under devices.

  I also checked in the BIOS to see if it it turned on and it is.
  The only thing I changed in the BIOS are Secureboot (is on) and has chosen CSM (UEFI), but I think that these settings are not relevant to the problem because they are used for starting.

  I tried to uninstall and reinstall the driver 3 times.

  Please help me with this problem.
  Thank you very much
  Andrei Colombi

  UEFI / start MSC mode has no influence on the fingerprint sensor.

  You said you did a clean install of 8.1 to win.
  I guess that the problem is related to the driver missing or utility.
  I guess you do not have all the essential software available on the Toshiba UE driver page.

  System driver Toshiba to win 8.1 must be installed. It is very important driver package.

  But also try to register fingerprints first in the Windows settings.
  Go to the control panel? Audio equipment &? Biometric devices
  To the left, click Change biometric parameters
  Now, you will see two options: WE (marked) biometrics and biometric OFF (unmarked)
  Now, go to biometric OFF and save changes
  Now go back and click on settings again biometric change
  Now return to the biometrics IT and save the changes.

  Now, you have to click on use your fingerprints with Windows and register fingerprints.

  I think it might be useful to get the utility of fingerprinting works again.

• Portege Z30-A-108 - use of the headphone/microphone jack

  My Portege Z30-A-108 (running Windows 7) has a unique plug taken jack for headphones/microphone. I want to connect my combination of headset to use Skype, but like everything I've seen has separated mini jacks for headphones and microphone. If I plug the headphones there is no microphone, while if I plug the microphone as PC speakers are dumb there is no sound.

  I discovered that if I plug or in, but go to the Panel of control-> Sound-> recording, Microphone click on properties-> listen-> listen to this device, and then the computer's microphone seems to be activated and his captured it out with the sounds of the PC speakers.

  What is the best way to do things?

  Your model of laptop has only one port, designed for the use of the Mono headset.
  If you want to use usual helmet with two plugs I recommend you to use USB stereo Audio adapter.

  Google a bit autour and you will find a large number of them. It's cheap, so I think it's the best solution for you.

• Portege Z30 - I am unable to send SMS

  I have a Portege Z30-A-13F. On the previous Portege, Ericcson device shipped, I used the Toshiba Wireless Manager and the SMS from Toshiba utility in access card for messages (SMS).

  Currently, with the integrated chip of Sierra, I am able to access the network, but there is no interface for SMS on the AirCardWatcher tool.

  The Wireless Manager does not work (I think it only works with Ericsson devices).
  Is it possible to use the SMS with this computer?

  Thank you very much

  AFAIK this is regardless if the laptop supports the Ericson or the Sierra 3 G module.

  The Toshiba Wireless Manager should work fine in two modules.

  Check this document... He explains how to set up and establish a 3G connection via the Manager preinstalled Toshiba wireless.
  http://APS2.toshiba-tro.de/KB0/FAQ1A037W0000R01.htm

• Portege Z30 - B - 10 c: is THNSNJ256GMCU SSD supports hardware encryption

  I have a Toshiba Portege Z30 - B - 10 c with 256 GB SSD (exact model THNSNJ256GMCU).
  On the Internet I found weather mixed info, this drive takes in charge or no material encrytpion.

  Could someone help me find the answet to this question and, if it supports encryption.

  How to activate it?

  THNSNJ256GMCU

  Main features
  • Capacities up to 512 GB
  • Available in four Standard form factors
  • MLC NAND Flash memory
  • Low-power Devsleep feature support
  • The end-to-End data protection
  • Gravitational quadruple Code technology (reverse)

  More features
  • Translation mode which allows all disk configurations
  • Hot plug/OS-Aware removal
  Exclusive Toshiba • error correction technology, reverse (Quadruple gravitational Code Technology) support
  • Read only mode supported for emergency

  http://Toshiba.SEMICON-storage.com/e...t-SSD/Hg6.html

• Portege Z30-C-12Z cam does not work with Win 10

  Hello!
  I have a problem with my Portege Z30-C-12Z. Camera in win10 does not work.
  Error code: 0xA00F4273. Have tried all the following steps: http://answers.microsoft.com/en-us/w...0-71c220c123a9 and like many more check the BIOS etc.

  According to me, I tried and everything, checked it please help!

  Try this:
  Type of storage in the search window and go to the storage system settings page. Make sure that the economy sites point to existing folders.
  I moved the files on a SD card and the camera could not find the folder of photos. Also, I've seen the suggestion to check that the folder of photos contains the security settings to allow access.

  If still no good, remove the driver of the webcam from the Control Panel, then let Windows Update to install a driver for the webcam update.

  Reinstall the camera application can also help.

• Portege Z30-A-12N with Port Replicator Port Hi-Speed USB III problems

  Hi all

  I have a big problem with my new Portege Z30-A-12N and Hi-Speed Port Replicator III.

  I connected the power, DVI, LAN, mouse and keyboard to the Port Replicator.
  Power, DVI and LAN are okay, but none will be found if I connect something to the USB Ports 2.0 or 3.0.
  No mouse, no keyboard, and no USB key.

  When I start my Portege I must enter a password after you press the power button.
  These password, I could enter with the external keyboard, but in windows, no keyboard has been found.

  If I connect the keyboard and mouse to the USB Ports of the Portege instead of Port Replicator, the two has been found.

  I ran Windows 7 Enterprise on the Portege.
  BIOS version is 3.30

  Do you have a solution for me?

  Hello

  The HI-SPEED PORT REPLICATOR III PA5116E-1PRP supports 2 x USB 2.0 and 4 x USB 3.0 ports.
  You n t special need Win 7 drivers in order to be able to use the USB ports or other interfaces such as VGA, DVI, audio, etc.

  Sound problems, make sure that the audio device has been selected in the right panel-> sound-> playback tab

  By the way: Win 7 needs USB driver 3.0 which is preinstalled when the laptop was equipped with USB 3.0 ports. My knowledge if your mobile phone does not support USB 3.0, you will be able to use the port replicator USB 3.0 ports.

  Finally and above all devices must be connected before you start the computer. The decision supported and compatible specifications: Portégé R30 - A, Tecra Z40 - A, Tecra Z50 - A, Portégé Z30-A/Z30t-A, Tecra A50 - has

• Portege Z30-A-181 - win 10 graphics driver need - not strong enough screen

  Hello

  I would ask you for help. I've had my laptop PORTEGE Z30-A-181 PT243E 08305SCZ last November. I'm upgrading my OS to W10 64 bit and get into trouble with the DISPLAY DRIVER. It is not official for this PC display driver
  also, it's a laptop of high qualitity. I use W8/W7 64 bit drivers.
  Most of my screens is not sharp and smooth.
  Could you let me know, what to do?
  I was told that the laptop is not on the list of supported laptops.
  http://www.Toshiba.EU/innovation/generic/Windows10/
  It's a laptop 900pounds, hope, therefore, it is only poorly understand.

  Thank you.
  Kind regards
  M.Bitman

  I have not yet installed Windows 10, but the z30 - a should be on the list: https://www.toshiba.eu/innovation/ge...ws10-business/ (link to business-products)

• Portege Z30 16 GB with high speed Port Replicator III and two monitors - resolution

  I have a Portege Z30 with 16 GB of Ram, connected to a Toshiba high speed Port Replicator III which is connected to two monitors running in mode extended.

  The monitor attached to the first section of the video is 1920 x 1200 running.
  However the second monitor is only show support for a maximum of 1280 x 1084.

  The monitors are identical, and both are connected by DisplayPort cables.

  I tried to lower the resolution and save the settings on the first monitor to see if it offered options on the second monitor, but the options remained the same.

  At this point, I have narrowed down to 1280 x 1024 so that it conforms to all the monitors but would like to a plus-res solution.

  Does anyone know if there is a fix/work-around for this?
  If this is a hardware limitation, has anyone tried a USB 3 to DisplayPort adapter in a similar configuration?

  Thank you!

  At the same time using two displayports?
  I wonder how it is possible, because of my knowledge it is not possible... as far as I know the Port Replicator III supports two DisplayPorts but you could choose and use one of them...

  In any case, you can use both with a lower resolution, I guess that this problem can be caused due to incompatible display drivers.
  I suggest you to uninstall reinstall or update the display drivers and check if it helps

• Portege Z30 - A - Ubuntu 14.04 - Sierra Wireless

  Hello

  Toshiba Portege Z30 - A
  PT241E-01D00QPL

  Windows 7 - there are interface "Sierra Wireless Mobile Broadband Network Adapter".

  Ubuntu 14.04 - there is nothing of :-(
  Only -.
  Bus 002 Device 003: ID 1199:9063 Sierra Wireless, Inc. sudo modprobe usbserial vendor = 0 x 1199 product = 0 x 9063

  What can I do?

  Perelka

  Hello

  There seems to be a bug in Ubuntu.
  See this bug report:

  https://bugs.Launchpad.NET/Ubuntu/+source/modemmanager/+bug/1326954

  Tom BR

• Portege Z30-A-183 - data Erase finger finger

  Hello

  I have a Portege Z30-A-183.
  First of all, I used it with W7 and I recorded 3 fingers in the biometric fingerprint sensor.

  After that I updated to W8.1 but I have not deleted the scanned data of the fingers.

  W8.1 I haved comand to again record the data of my fingers, but the software says that it is not possible beacause in the memory of the sensor data of my fingers.

  I have haved read that these data are in a non-volatile memory on the sensor.

  How can I erase that data?

  Thank you

  Hello

  Yes fingerprint information is not saved on the hard drive (HDD) on your computer, but on some the chip.

  Usually the imprint must be removed using the utility of fingerprints, but if this does not work after the installation of the new operating system, I recommend you go back to the previous state before changing the system and use the fingerprint software which has been used for the registration of fingerprints.

  Details here:
  http://www.MyToshiba.com.au/support/items/FAQ/386

  But where the fingerprint would not work even using the version of Win 7, I think that this only Toshiba authorised service provider would be able to remove fingerprints already recorded.