VMware ESXi 5 host stops sending the syslogs to the remote server (Splunk)

Similar Questions

• Stop and restart the virtual machines in the remote server

  I need to close virtual machines running guests 4 1 ESX from a remote server (IBM System i).

  The remote server in fact control the storage used by ESX and VM OS, so I'll have to scripts running on the remote server that:

  Stop the virtual machine

  Performs maintenance

  Reboot the virtual machine

  I tried to understand the big picture of the reading discussions here, but I'm still confused.

  VMA is to provide the best way for the virtual machines of withdrawal from a script running on a remote server?

  Scripts can I use SSH to connect to the vSphere environment to run scripts or issue the command?

  Thank you.

  vCLI (really its vSphere SDK for Perl), PowerCLI, VI Java, etc are all vSphere SDK to correct and they are a of the client-side bindings different scripts and programming languages which bind to the vSphere API. When I say 'API', I mean using one of these SDK is you use the vSphere API to perform the work.

  The SDK is initiated on the remote server, this can be windows, linux, etc as long as it supports one of these boxes to tools. In general, for admins, you will use either vCLI (vSphere SDK for Perl) that supports Linux and Windows, or if you are more windows-oriented, you can use PowerCLI.

  Documentation has been referenced in my first post, please take some time the documents because they provide much more detail on the use cases for each + a lot of examples with orders. Yet once, there no involved SSH if you use the vSphere API. As I told, vMA is a virtual appliance, you can download and start using if you do not want to install vCLI or PowerCLI on a remote system, this is assuming that you are comfortable in a Linux environment. If you're not, then I highly recommend using PowerCLI, who will need a remote server for Windows.

  Here are a few started getting additional resources:

  vSphere SDK for Perl + vMA:

  Getting started with vSphere SDK for Perl

  Introduction to the vMA (tips/tricks)

  PowerCLI:

  http://www.VMware.com/support/developer/windowstoolkit/

  http://www.virtu-al.NET/2009/11/10/PowerCLI-where-do-i-start/

  =========================================================================

  William Lam

  VMware vExpert 2009

  Scripts for VMware ESX/ESXi and resources at: http://engineering.ucsb.edu/~duonglt/vmware/

  Twitter: @lamw

  repository scripts vGhetto

  Introduction to the vMA (tips/tricks)

  Getting started with vSphere SDK for Perl

  VMware Code Central - Scripts/code samples for developers and administrators

  VMware developer community

  If you find this information useful, please give points to "correct" or "useful".

• "The remote server returned an error: (502) Bad Gateway" while matching Protected Site VC and recovery Site VC in VMware SRM

  Hi all

  I am trying to Setup VMware SRM 4.1 groups. I had configured hitachi usp vm storage based array replication in both sites.

  Now when I try to pair the two sites vCenter, I get an error at the end of the phase of matching as message "the remote server returned an error: (502) Bad Gateway ' on the protected site. But surprisingly, I am able to match both the vCenters on the recovering site.

  Please help me to get the problem.

  Thanks in advance,

  Sanjeev

  Run telnet server vCenter/SRM protected site to the recovering site server vCenter/SRM:

  Telnet IP_ADDRESS 80

  Telnet IP_ADDRESS 443

  You succeed?

• plugin VMware update manager returns with "the remote server returned an error: (404) not found."

  Hello

  We have recently updated our virtual Center Server to version 4 and now when I try to download and install from the page manager plugin vmware update manager plugin is back with "the remote server returned an error: (404) not found"

  Has anyone had this problem before and eventually worked out how to fix this?

  Gregg Robertson, VCP, MCSE, MCSA, MCTS, MCITP

  You are welcome!!

• invoke VMScript unable to connect to the remote server

  I have two PCs, two win 7 x 64. PC1 has powercli 5.5 build 3142196 (5.5u2?) and the other who has now updated 6.0.0.7857 (last AFAIK) via VMware PowerCLI - 6.0.0 - 3205540.exe from the downloads section.

  On PC1, I can run the script

  invoke vmscript - ScriptText '(gwmi_win32_computersystem).manufacturer - like ' * vmware * "'-ToolsWaitSecs 45 - VM VMName - guestuser guestacct - guestpassword blablabla".

  and it works very well and gives me a result.

  If I run the same command on PC1, I get the error:

  Invoke-VMScript: 16/11/2015-18:32:01 VMScript Invoke cannot connect to the remote server

  on line: 1 char: 1

  + Call VMScript - ScriptText '(gwmi_win32_computersystem).manufacturer - like ' * vm...»

  + ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  + CategoryInfo: NotSpecified: (:)) [invoking-VMScript], ViError)

  + FullyQualifiedErrorId: Client20_VmGuestServiceImpl_DownloadFileFromGuest_DownloadError, VMware.VimAutomation.ViCore.Cmdlets.Commands.InvokeVmScript

  Anyone encountered this before? I see no difference in the PC it would cause and I wonder if there are logs, etc. for troubleshooting, I'm not aware of. The message is a bit lacking in detail. Probably the client must connect something.

  Thank you!

  The client when you run the Invoke-VMScript cmdlet on must actually be able to connect to the physical ESXi host on which the virtual computer runs on port 443. Are two clients on the same subnet, you have a firewall between the hosts and guests? Just try to open the ESXi host welcome page in a browser from these two clients, e.g. https://myesxihost.local/

• SRM 5.5 - the remote server returned an error: (503) server unavailable, could not create SSL/TLS secure channel

  Design:

  2 vCenter VMs version 5.5 on new W2k12. x. related and the same use facilities key SSO (default installation)

  2 x fresh install of the SRM VMs version 5.5

  20 + hosts vSphere 5.5 with DR/HA configured and working. Two dvSwitches (one per site) configured with the groups of port / VLAN work

  Question:

  Installation goes well until I needed to activate the Plugin SRM in vCenter.  Plugin called "Plug-ins available" and I click on the link 'download and install '.

  I had two separate fouls on both servers vCenter, both with same errors if it is compatible.

  Errors:

  (attached file viclient-3 - 000.log)

  The request has been aborted: could not create SSL/TLS secure channel.

  (attached file viclient-3 - 000.log)

  The remote server returned an error: (503) server unavailable

  I guess that the two are linked and probably something with SSO.  Post installation on each server vCenter vCenter, at the level of the vCenter, I added the "Domain Admins" AD Group with all permissions and then properly connected and built the group with this set of credentials.

  I need help to debug this further.

  Thank you

  ************

  < < Updated > >

  Seems the features and functions are NOT present so you don't not sign in as '[email protected]' (SSO account by default for this "basic" configuration)

  But even with this connection, I have noticed that there is NO option in the webclient service, to perform the installation of a vCenter plug-in.  It does not appear in the vSphere Client (see images).

  I also found it weird that the web client to vCenter illustrates SRM roles but the traditional client does not work.

  Maybe it's a clue to the root cause of...

  Post edited by: ArrowSIVAC 2013-10-07 to provide more details and attachments

  Post edited by: ArrowSIVAC, this is related to the case of support for vmware 13384832210 This problem is solved.  Several pieces here. (1) vCenters were installed secretly with local account as own databases, and this is how I usually do things (2) MRS. servers were built as separate virtual machines, VMWare vs guides guess and documents in anticipation of your SRM installation on the same server as vCenter Documentation / Installer is not clarified that you MUST use domain for MRS accounts in the multiplayer linked site facilities and if you do not, the installation is completed without error, but resources will not work. Errors have for client plugin does not work. It was the symptom, the reason was that the SRM service did not work.  The service would not start and only an error in the Windows event log is 'vmware-dr stopped service' is because the connectivity issue of MRS to vCenter hosted the new SQL instance database SRM. The SRM database has been installed on the instance of vCenter server as vCenter database.  And just like the installation of default vCenter I chose localhost\administrator for database owner.  The database was filled with tables, but SRM has connectivity problems.   The fix for this was to add "domain\user" (called mine SRMAdmin and added as a member of domain admin), add this user in SQL in the list of database users and then promoted as the owner of SRM database and define the rights on DBO. This fixed the first issue. Second issue was that SRM installation set the DSN system identification information, but does not specify that they must also be domain based accounts.  The installation program is not not clear here and should only allow user domain\username when installing. After several attempts because of the root and installation methods different tried, how to get the installation complete and properly configure was to log on to the system AS the example domain account: domain\srmadmin = > Configuration System DSN by selecting "How should SQL Server verify the authenticity of the login ID?"  "with integrated Windows authentication', and then the installation of SRM to the"Enter Database user credentials"value"domain\srmadmin ".  Then and communication services to the vCenter SRM hosted DB database will work correctly. < See images attached benchmarks >

  attached files

• FTP adapter: Not picking not the file on the remote server

  Hello
  
  I use the FTP adapter to read the file from the remote server and file ra.xml - oc4j configured with good host, port, username and password.
  
  Once I have deployed my process, no instance of this process is created and remote directory entry file is not picked up.
  
  Please help on this issue. Thanks in advance.

  Just checking that you can send via ftp manually from the BPEL server.

  Looks like you can use the ra.xml - oc4j wrong file.

  Also in your BPEL project, take a look on the link partner FTP and see the JNDI location, it will look something like eis/Ftp/sample.

  This may be what you want to rename, generally good naming practices puts the server, for example Ftp/ist/FtpAdapter

  To make sure that you have configured the file ra.xml - correct oc4j we can check through the Manager of the company, even though Marc has specified the correct location.

  EM-> oc4j_soa-> Applications-> Drop down choice list autonomous resource adapters-> FtpAdapter-> connection Pools

  Select the JNDI name, you indicated in your BPEL process, if there is no create a.

  Create connections as needed.

  Also a hint is to start with the base directory, for example when you connect by ftp manually, it will be where you load the files. In your configuration / (oc4j - RA.Xml) is the place of departure and / is the physical or logical path. Download this work so that you know that you have the right connection. Then start working on the location of the directory.

  see you soon
  James

• What are the network requirements for the remote server of the Panel?

  What are the network requirements for the remote server of the Panel?

  I tried for awhile now to set up a Control Board.  I can connect to my remote panel of computers from other computers on my local network but nowhere else.

  Whenever I use web publishing tool gives me a URL in this format: Http://Computer-Name.Corporate-Name.local:8086 / VI - nom.html apparently it means I have a local DNS server and this URL is meaningless to the public.

  When I try to connect with the Operate > Connect to... remote control, I get this error message:

  "Connection to Server remote panel...".
  "Connection refused by the server remote control specified: make sure that the LabVIEW Web server is enabled on the specified server.

  I got the same error when I tried to host a remote panel from my laptop at home, on my Wi - Fi.  Is there some network settings or firewall I'm not seting?  Would it be my server or the router or the private network?

  My goal is to be able to host remote panels of my laptop while I'm on the international scene, creating using 4 G internet mobile.  Is it still feasible?

  As he Turners on my router had to be put in place so that my Port is in the rage of transfer.  Also I had to disable DHCP.  Without that you cannot host behind a router.

  These are the instructions I put fallow:http://digital.ni.com/public.nsf/allkb/B1E9A3D78BAED949862573AD0065D4D2

• connect to the remote server

  Hello friend

  Pls help
  Given below to other site, ip address of the server 172.16.5.10 and public IP address 41.59.251.X, I need to create the tunnel so that my
  Server with the ip 172.17.18.41 and my public IP 41.59.251.Y must be able to communicate with the remote server which is

  172.16.5.10
  What is the way forward? my server ip address 172.17.18.41 mask 255.255.255.33

  -3des encryption
  -Md5 hash
  -Preshared authentication
  -Group 2
  Pre-shared key 66@#fgk
  -Public IP 41.59.251.X
  -ip address of the server 172.16.5.10 (he is 27 subnet)

  Is what I want to implement, help the routing between two networks and access-list for only two servers to talk to pls

  crypto ISAKMP policy 30
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  ISAKMP crypto key 66@#fgk address 41.59.251.X
  Crypto ipsec transform-set STRONG esp-3des esp-md5-hmac
  JOE 30 ipsec-isakmp crypto map
  set of peer 41.59.251.X
  86400 seconds, life of security association set
  transformation-STRONG game
  PFS group2 Set
  match address 140

  access-list allow 140
  IP route

  interface GigabitEthernet0/1
  Description CONNECTION to ISP
  IP 10.17.50.1 255.255.255.252
  IP virtual-reassembly
  automatic duplex
  automatic speed
  JOE crypto card

  Joe

  En to encrypt traffic must match the access list, and it must match the list of access on the other side.

  The easiest would be to ask the person manageing the router on the other side to send you the configuration, otherwise it's just a guess how this access list must be configured.

• CSS style sheet appears on the remote server when I download my Web site, but it works very well to the local server

  CSS style sheet appears on the remote server when I download my Web site, but it works very well to the local server, if anyone can help I would be grateful.

  There are major problems with this page as shown in the screenshot below.

  

  This is caused by a liberal hijacking of APDivs (aka layers) for a main page layout.  This isn't what APDivs were intended.  That's why Adobe them removed from DW.  Unfortunately, not soon enough.

  I think you're the best option is to start over with a pre-built CSS layout that doesn't contain positioned elements.

  Either way, Flash is dead now.  Most of the people cannot display Flash media more.  You can convert the HTML5 video or use YouTube to host videos now.

  Nancy O.

• not be able to collect some Logs Errror: unable to connect to the remote server

  I'm trying to collect Diagnostic information requested of VMWARE and I get an error message

  Error state HOME

  Complete XX.XX.XX.xx

  Complete XX.XX.XX.xx

  YY.yy.yy.yy could not connect to the remote server

  YY.yy.yy.yy could not connect to the remote server

  Bundle of newspaper has not YY.yy.yy.yy has not generated

  VCenter Server full

  VMware Vsphere Client full

  I don't know their reasoning for this, but it seems like a pain in the thigh. Why not just export logs with the vSphere Client? File-> Export-> Export System Logs

  Or

  Use the help wizard that will allow you to collect and automatically download newspapers in vSphere?

  http://www.VMware.com/products/Datacenter-Virtualization/vCenter-support-assistant/overview.html

• Please help, data queue on the remote server

  Hello Experts,
  
  Kindly help, to learn how to roll up the data from the remote server. I need a detailed procedure to make settings on my local machine to connect to remote Oracle using SQL Server * MORE.
  
  I installed on my local machine which is 32-bit Oracle 11 g Release 2:+.
  
  SQL * more: Production of release 11.2.0.1.0 Fri Feb 8 12:02:30 2013
  Copyright (c) 1982, 2010, Oracle. All rights reserved.
  
  Enter the user name: SYSTEM
  Enter the password:
  
  Connected to:
  Oracle Database 11g Release 11.2.0.1.0 - Production
  
  SQL >
  
  and on a remote server below is the version installed.
  
  Log in as: B_DB1user
  [email protected] password:
  Last login: Sat Feb 7 18:19:35 2013 10.10.167.8
  [B_DB1user@bamdb001 ~] $ sqlplus
  
  SQL * more: version 11.1.0.7.0 - Production Fri Feb 8 12:06:35 2013
  
  Copyright (c) 1982, 2008, Oracle. All rights reserved.
  
  Enter the user name: B_DB1user
  Enter the password:
  
  Connected to:
  Oracle Database 11 g Enterprise Edition Release 11.1.0.7.0 - 64 bit Production
  With the partitioning, Real Application Clusters, OLAP, data mining
  and Real Application Testing options
  
  SQL >
  
  ----------------------------------------------------------------------------------------------------------------------------
  That's what I have in tnsnames.ora
  
  tnsnames.ora # Network Configuration file: E:\app\managerproj3\product\11.2.0\dbhome_5\network\admin\tnsnames.ora
  # Generated by Oracle configuration tools.
  
  LISTENER_ORCL =
  (ADDRESS = (PROTOCOL = TCP)(HOST = localhost) (PORT = 1521))
  
  
  ORCL =
  (DESCRIPTION =
  (ADDRESS = (PROTOCOL = TCP)(HOST = localhost) (PORT = 1521))
  (CONNECT_DATA =
  (SERVER = DEDICATED)
  (SERVICE_NAME = orcl.10.167.8)
  )
  )
  
  ---------------------------------------------------------------------------------------------------------------------------------
  That's what I have in listener.ora
  
  
  listener.ora # Network Configuration file: E:\app\managerproj3\product\11.2.0\dbhome_5\network\admin\listener.ora
  # Generated by Oracle configuration tools.
  
  AUDITEUR1 =
  (DESCRIPTION_LIST =
  (DESCRIPTION =
  (ADDRESS = (PROTOCOL = TCP) (HOST = 10.10.167.8)(PORT = 1521))
  )
  )
  
  ADR_BASE_LISTENER1 = E:\app\managerproj3
  
  LISTENER =
  (DESCRIPTION_LIST =
  (DESCRIPTION =
  (ADDRESS = (PROTOCOL = CIP)(KEY = EXTPROC1521))
  (ADDRESS = (PROTOCOL = TCP)(HOST = localhost) (PORT = 1521))
  )
  )
  
  ADR_BASE_LISTENER = E:\app\managerproj3
  
  ------------------------------------------------------------------------------------------------------------------------------------------
  
  
  Database server: ORACLE
  HOSTNAME: BAMDB001
  IP address: 156.1.3.4
  
  
  and here is the script I tried data spool in the local computer using SQL * MORE
  
  set colsep,
  set pagesize 120
  Set trimspool on
  headsep off Set
  set linesize 1000
  
  coil D:\test\myfile.csv
  
  Select table_name, tablespace_name of all_tables;
  
  spool off
  
  It is effective on the local machine... Please help me to get the data from the remote server to the local computer?
  
  Kindly let me know if you need anything whatsoever.
  
  Thanks in advance
  
  Kind regards
  Bosch

  Is not more or less the same question you asked in {message identifier: = 10835497}?

  You must have a user to the remote database and an entry for the remote database in your tnsnames.ora file

  If you have just to coil of database of remote and local database didn't need to be involved:
  Edit your tnsnames.ora and add an entry with the remotedb, the information and you need to have the following information:

  Ip address or the name of the server (BAMDB001?)
  Name of the service (?)
  Port configured for this database. (??)

  Also, you must be sure that the connectivity of your local computer to a remote server is granted (without firewall block).
  Only when you have this information, you can connect to the remote database from your laptop.

  From the Unix server where you connect to the database, you can get the information to be inserted in your local tnsnames.ora by typing:

  tnsping dbname
  

  Of course, you need to replace dbname with the name of your database.
  Another way is to check the remote tnsnames.ora when logged in Unix:

  cat $ORACLE_HOME\network\admin\tnsnames.ora
  

  and check the configuration it.

  Kind regards.
  Al

• Configure the remote server and test

  I installed Dreamweaver CS 6 and 10 CF and MS SQL server on the same computer.

  I use Dreamweaver CS 6 to create a test web site and to set up the remote and testing server.

  Dreamweaver invite me to enter the host name and the full directory.

  I would like to know what I need to enter information?

  hostname is localhost?

  complete diretory will C:\inetpub\wwwroot or C:\ColdFusion10\cfusion\wwwroot?

  Your information and your help is much appreciated,

  Kind regards

  iccsi,

  Iccsi,

  Yes. Host name to the title of "Test Server" is the hostname of the server test - in your case, since you're using CF, it must be the path in which CF works. It will be localhost:8888 or something similar - depending on what port you have configured for the webroot when installing CF. you could check in CF dashboard. Or, you could start CF server, open your browser, enter localhost. If the loading of the page Web of the CF by default, it's just localhost. If this isn't the case, add the port number.

  The remote server is your real Web server. It may be http://www.somesite.com or if you run it in a separate folder within your main site, it will be http://www.somesite.com/test - depends on you want to download the files of remote work.

  The complete directory under local configuration is the place where your files are located on your local system. Still, if you use CF, you can thus use CF webroot to create / store files - this way, you don't have to make copies of files in 2 places since that you configure the same folder as your test server too.

  -ST

• MySQL database does not work on the remote server help!

  Hello

  I'm kinda a noob in PHP/MySQL and I can't get my MySQL database to work on my remote server (it works on my local server).

  On the spot, I have:

  Connection name: local

  MySQL server: localhost

  User name: root

  Password: root

  Database: wbgt

  From a distance, I have:

  Created a database to help:

  username: wbgt (although it displays it as "web100-wbgt")

  password: root

  I also imported the MySQL database on the remote server.

  When I try to access any page that uses the MySQL database, it comes in white!

  Any ideas?

  Thanks in advance for your help

  Eddie

  Thank you! I got confused that it was not connect to the remote server.

  If someone else is in a similar situation as I was.

  I use heartinternet.co.uk

  1. export your local MySQL database
  2. create a MySQL database on your remote web hosting provider
  3. go to manage (or something similar) and import the MySQL database on your web hosting provider remotely
  4. in dreamweaver go to database data, +, MySQL connection Panel (or change your original database)
  5. Connection name - what you want
  6. MySQL - Localhost Server
  7. User name - whatever your remote site named the database in my case, I entered admin, but the user name is admin-web100-8
  8. Password - password for your remote database
  9. Database - go in manage your databases click on database and on the left side you should see the name of your database. in my case it was web100-admin-8 new (I couldn't connect on the ddatabase distance so I had to enter manually)
  10. Click fact put and it should work!

• Channel disconnected error with the remote server

  I created the Mobile Flex and PHP project that works very well with a local server (MAMP on Mac). Basically, it reads the data to get MySQL and displays the map Google. Now, I'm moving from a local server to a remote server.

  But when I run my application on emulater, I get the error "channel disconnected - disconnected prior to receipt of the acknowledgement of receipt."

  I Googled what this error is and found a web site that described on this error. According to the web site, the error is probably due to a PHP syntax error and use Network Monitor to debug it.

  However, the problem is that after I activated the network monitor and run my application on the emulator, nothing appears on the monitor network. My first question is if I should use Network Monitor to debug this error of channel disconnectef? The second question is negative, how can I debug this error? Any help would be appreciated.

  I finally understood what I was doing wrong. I followed the insturction of davidflexto http://forums.adobe.com/thread/875709 and didn't I have to set host = 'localhost:8889' in my php that connects to my remote mysql server. It's delicate sicen is remote server, you set host = your domain name, but that's not true. Like davidflex said you need to set host = ' local: 8889 "since your gateway.php is also running on the remote server.

  I fell for several weeks and hope that someone else get stuck like I did it for several weeks.