Vocals and guitars/keys using multiple output

Similar Questions

• Using the output with 6009 or 6216 possible buffer?

  Hello

  I have a USB6009 and a USB6216. I need to generate a signal by using the analog output and I would use the output buffer. My questions are:

  -The USB6009 has an output buffer? I always get an error, but I know from experience that this device is very limited, so I wonder if they have not only an output buffer... (Programs in input buffer are not a problem at all).

  -J' took the USB6216 and I tried the example WfmGenUp.c downloaded from somewhere in the area of the developer (sorry I lost the link but fix the code) but I am not all analog output signals and after you press ENTER to stop the program (depending on the show) I get this error message:

  NO MORTALS RUN - TIME ERROR: 'WfmGenUp.c', line 113, col 9, id thread 0x0000088C: DAQmxStopTask function: (is-200016 return value [0xfffcf2b0]). Measurements: On-board memory precision passing. Due to the limitations of system and/or the bandwidth of the bus, the driver could not write data to the device fast enough to track the rate of output of the device.  Reduce your sampling rate, change the method of transfer of data (from interruptions on DMA), use a product with more on-board memory or reduce the number of programs that your computer runs simultaneously. Task name: _unnamedTask<0> Code of State:-200016

  I don't know if the problem is just that the 6216 does not support the output buffering or the other...

  -So, if the output control is not supported by 6009 or 6216 what would be the best way to constantly generate signals to 100 s/s?

  Thank you very much

  Kristel

  Hi Ryan,

  the USB-6009 case has 150 s/s softwaretimed AO, so you won´t be able to use AO stamped with the module.

  The USB-6216 supported in the analog output buffer, just follow the recommendations that the driver gives you,

  for example by reducing the sampling frequency, if there is an overflow memory due to the limitations of system and/or the bandwidth of the bus.

  Experiment with the parameters and the basic to see in what range of sampling it works.

  You can find appropriate examples

  ANSI C:

  C:\Dokumente und All Anwendungsdaten Users\Dokumente\National Instruments\NI - DAQ\Beispiele\DAQmx C\Analog Out\Generate Voltage\Cont Gen Volt Wfm - Int Clk ANSI

  LabWindows CVI:

  C:\Dokumente und Users\Dokumente\National Instruments\CVI\samples\DAQmx\Analog Out\Generate Voltage\Cont Gen Volt Wfm - Int Clk Anwendungsdaten All

• is it possible to save the Office XP for multiple monitors and restore after using the laptop in mobile mode?

  Is it possible to save the Office XP for multiple monitors and restore after using the laptop in mobile mode?

  Hi Kenelms,

  You can follow this link & check if it helps.

  HOW to: Set up hardware profiles for laptop computers in Windows XP

  Hope the helps of information.

  Please post back and we do know.

• wireless multimedia keyboard Microsoft 1.1 on my desktop using Vista home premium and the keys are coming all wrong

  I have a multimedia keyboard 1.1 microsoft wireless on my desktop using Vista Home premium, and the keys are all coming up badly, when I type 'k' for example I get 'a' or if I type 'p' I get 'v' and give me space '9' someone can tell me how to solve this problem?

  Hi Winchesterdream,

  Welcome to the Microsoft answers community site.

  I suggest you try the following steps

  Step 1: Connect the keyboard to a different computer. If the keyboard works correctly on another computer, the port to which the keyboard was connected on the original computer may be damaged. If this is the case, contact your computer manufacturer to find out how to repair or replace the damaged port.

  Step 2: Download and install the latest keyboard software

  To download the latest drivers for the keyboard that you use, see the following Microsoft hardware Web site:

  http://www.Microsoft.com/hardware/download/download.aspx?category=MK

  Step 3: Press the SHIFT key to turn five times keys Stick On or Off and check if the problem persists.

  Let me know if it works. Good luck!

  Hope it will be useful.

  Thank you and best regards,

  KKS Vijay

• Suggestion: It's about the COPY PASTE function. It is possible to apply multiple copy and paste feature uses publishers or any application of MS?

  Suggestion: It's about the COPY PASTE function. It is possible to apply multiple copy and paste feature uses publishers or any application of MS? For example, I need to copy the 4 lines of text and want to paste in 4 different applications. First line on the 1st application, 2' nd on the other and so on. With this I can choose 1st line and COPY 1 copy, nd line 2' COPY 2 and so on. And while pasting, I can choose the necessary text to PASTE 1,2,3 or 4.
  This feature takes really where people have to work with text editors in their daily lives and find these scenarios quite often.
  I have no idea if this feature is already encapsulated in the MS Editors, so if it's already there kindly let me know.

  Thank you.

  Kind regards
  Fahad

  Send your comments to MS and request this feature in Windows 8:

  http://mymfe.Microsoft.com/Windows 7/Feedback.aspx? formID = 195

  "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• Can I use Dell original product key to activate a clean Windows installation after I have replace/upgrade motherboard, processor and other key components?

  I have a Dell computer, with Windows 7 Home Premium 64-bit installed in the factory. There is a product code for windows on the sticker on the box. My problem is that the motherboard and CPU are released. I intend to replace and update the motherboard failed and cpu, ram, power supply, optical drive and eventually put in a larger hard drive. From what I read, I can not simply start the machine with the original hard drive, with windows already installed and activated. So if I wipe the hard drive (or put it in a new), can I clean install Windows 7 and then just use the product key on the sticker on the box to activate the new installation? Or what I need to buy a new copy of Windows 7?

  I've also read on other threads, that you can "transfer" a license of Windows 7 on a different machine only if it is a "commercial" version, not OEM. If the version of Windows that is preinstalled on a Dell computer would be "retail" or "OEM"? And to reactivate the software on a rebuilt/updated machine up-to-date with the new motherboard, etc. would constitute a 'transfer to a new machine' or reactivation just on a computer upgraded?

  The OEM of Windows 7 versions are identical to the versions commercial full license with the following exception:

  -OEM versions don't offer any free direct support from Microsoft technical support Microsoft

  -OEM Licenses are tied to the computer first you install and activate it on

  -OEM versions allow all hardware upgrades except for an upgrade to a different model motherboard

  -OEM versions does not move directly from an older Windows operating system

  What is OEM software? :

  http://support.Microsoft.com/GP/oemsupport_1/en-GB

  Licensing FAQ:

  http://www.Microsoft.com/OEM/en/licensing/sblicensing/pages/licensing_faq.aspx

• Body crashing all the time when I have the shuttle using the J and L keys

  Can someone please help? I seem to have really struggling with constant crashes when I try the shuttle well clips using the L and J keys. Any suggestion would be great. Thank you

  We have fixed some problems here in the version 9.0.2 update yesterday, can you make sure that you have updated?

• How to get the public and private keys to use recaptcha?

  I registered with google to get a recaptcha for my Web site. I've gotten has been the key to site and the secret key! If I need to get the public and private key for muse!

  Hello

  Please use the site as a 'public key'key key and Secret as "clΘ privΘe".

  Concerning

  Vivek

• Call stored procedures and using its output parameters in a report

  Hello
  
  I have a procedure defined in a package on the database. This procedure returns a number of output parameters. How to call this procedure and use the output parameters in my report?
  
  Thank you, Mark

  Depends on the level at which the procedure should be called. If its at the State level, call the form in the trigger-REPORT-BEFORE (or AFTER-PARAMFORM) and store the off-values space reserved columns. These you can use anywhere in your report.

• Cannot use the output VGA on my Satellite A100

  I have laptop Satellite A100 and when I use the my monitor VGA output announcement there is NO signal. I checked my monitor and it does not work.

  This that I would like to know because there is no my VGA output signal does that also mean that the * S-video * will not not a signal?

  I do not have a S-Video > VGA adapter as far trying to save the cost of buying one if it doesn't...

  I don't really know what you're doing wrong?
  Is your laptop connected with VGA cable or an adapter on your laptop VGA port?

  When the monitor is connected please use FN + F5 key combination to switch between an LCD display and connected monitor.
  It work?

• Specify the end point for the digital using an output circular buffer

  When you use DAQmx and a NOR-DAQ for issuance of a digital signal using a circular buffer (buffer Renault). The program works and works, but when the 'DAQmx Stop Task.vi' function is called to end the task, he stops at the output buffering as soon as it is called and does not wait until the buffer pointer reaches the final value in the buffer. I would like that the program to wait until the buffer pointer is on the last value in the buffer, does anyone know how to specify this setting?

  If you need to stop on exactly the last sample output you will need a way to trigger the stop in the material.  The options available to you will depend on what hardware DAQ, you use, but here are some possibilities on the top of my head:

  1. set up a digital output redeclenchables task finished (not all hardware supports).  Set up a counter of output to issue a periodic trigger with the necessary synchronization signal such that the end result is a "continuous" digital output without interruption.  When you stop your loop, stop the task of counter - digital output ends his generation but the trigger signal will be removed and so it will not continue after that.

  2. If you have an unused extra digital output line, add it to your task.  This line should exit 0 all except the last sample.  Physically, this additional digital line in a wire line PFI and use it to trigger a meter output.  Have the output counter generate a single pulse of some long-term (long enough to ensure that the software can respond prematurely).  Use the output from the task of counter as a trigger of break for the task of digital output.  Do not start the task of the meter until you leave your loop.  Do not stop the task of digital output until you have detected in the software that the meter has been triggered.

  If you need to stop on approximately the last sample output, you could query the TotalSamplesPerChannelGenerated property after leaving your loop and only stop the task once it reaches a multiple of the size of your circular buffer.  This is no guarantee that it stops on the last sample (if you use a device on a bus with a latency higher as USB or Ethernet the non-determinisme would be worse).

  Best regards

• A set of keys on multiple Machines?

  Hi all

  RIM code siginig keys are installed on my machine for clients. I want to use the same set of keys, to test the application on the device. I got the .db, .csk and machine customers .set files. I imported the key using the eclipse as editor. But when I try to sign the file of cod, it is asking password of private key.

  There is in fact no password of private key.

  How can I use them?

  while I google, I found the following info.

  Source: http://berrytutorials.blogspot.com/2009/10/code-signing-setting-up-eclipse-to-use.html

  A set of keys on multiple Machines?

  Once you install the keys on your box, you can't move them to another machine without going through the support of the RIM and asking new keys. If I understand correctly, this process invalidates your original key. The essential is that you may not use the set of keys on multiple computers so chose the box where you install the keys with wisdom.

  This info is all the justification of the RIM? Can I expect the Martin1 or documents of the RIM even consistent? or about the information above?

  Or is it any way to reuse the same set of keys on multiple machines?

  No, there is no charge for replacement keys.

• Need help! Re: Sequence Presets understanding &amp; settings + using multiple sequences!

  Hi, I'm newer to Premiere Pro (using the new version of Pro obtained in March 2010 on a PC) and watched all the tutorials (lots of video) and read a LOT about the subject! And I have answered several questions about mine. But there is one main thing (that I'll probably have to divide it into 2 or more questions) that I just got a complete knowledge & really your expert need help on!

  Thank you very, VERY MUCH! Really...

  I have designed/product audio (music) for a while now and when you start a new session just, you select your sample rate & are locked in for the most part therefore... Pretty simple... Now with Pro, when you start your new session, you choose your Preset sequence. Now for this first project, a video clip (3 minutes), the audio is done (as I said) and for the clip, we use images from several sources including: maybe 55% compared with a mini-camera DV, 40% of the .vob files right & the remaining 5% of some mpeg files + a few YouTube videos (we only have it our preserved images of front on YouTube) + some JPEGs (still images). And we plan to export the final video on YouTube and the internet. And we want also ready to be broadcast on both television (MTV, some media, shows, etc.). And Yes, we will also use it on cell phones (even if it is the least important right now). So 3 main exports (which I believe are all made at the end through media encoder).

  • But to choose the right Preset sequence at the beginning, I am confused, unfortunately.   I

  Believe you choose the one that best fits to of your assets sizes & frame rate [in this case, which is a camera film regular DV; & mediainfo said the .vob file = 720 x 480 (4:3) to 29.970 fps MPEG video (NTSC), one of the shots (of our) YouTube = 480 x 270 (16:9) at 29.970 fps STROKE, a MPEG = 352 x 288 (4:3) at 25.000 fps and 2 examples of jpeg = 300 x 400 (size = 57 KB)] and another = 720 x 450 (size = 100 KB)]. So if I am wrong in my assumption on the choice of a pre-defined sequence just on the best corresponds to the your assets rates & sizes, I would choose (I think): DV-NTSC Standard 48 kHz (the 48 just to 41 over our audio sampling frequency). 

  And if all goes well, it is excellent for our export needs YouTube at the end of the process the video & tv as well!

  .. . Is this correct?

  Can I choose the predefined sequence that best matches most of the sizes/frame rate of your assets?

  * And ESPECIALLY... is CE Preset of the sequence is the BEST for this current music video (based on the sources of our assets & where it will be considered when it is finished - mainly of YouTube, & also some TV [for media and broadcasting] - probably on a DVD, I guess)?

  Or I'm wrong, & it (your Preset Sequence) depends on your final product & the output?

  My friend (who admits that he is no expert in some way) explained that I would probably go with HDV 1080 p 30 as this will give a much better value for my release. But after he saw the results in Pro with this setting for my property, he agrees with MY above conclusion instead. 

  When you use the DV - NTSC Standard 48 kHz preset, I saw the asset in the Source monitor Panel (& then dragged the clips to the timeline) & seen in the finale of "Project Monitor" (I think it is called). And they looked decent in this final screen (where I'll crop & use some shared screens sometimes). 

  And when I used his suggestion of 1080 p HDV 30, assets looked ok in the Source monitor Panel (I think), but very little in the final project monitor. 

  • And led me to another big question - when you use the jpeg format which is 1280 x 960 e.g. (largest

  as the previous ones) in the Standard DV NTSC 48 kHz preset, happening in the Source monitor. But when you drag it down to the timeline and view it in the program monitor, the head was cut off, etc. and of course, when you use instead the HDV 1080 p 30 preset, as larger jpeg even adapt very well in the in the program monitor. Now, I understand that this is because the size of the frame (dimensions) close match those of the HDV preset. I get it. What none of us got was however WHY in the DV - NTSC Standard 48 kHz preset, he looks very well in the Source monitor Panel (but not in the program monitor)? (The two were simply put to 'Fit'). We thought he not would not have looked at well & fit fine and complete source of follow-up at first - but that's the difference between this largest jpeg display when it is displayed in two different monitors that really confused us!

  • And the final main confusion on this topic lies in something, that a technician in Adobe, tell us, informing that

  We can create multiple sequences. Now, I saw How to do this in the project Panel, but it's really the full understanding of the workings that we don't get. The tech said: "each sequence MUST have the good frame rates, sizes of images." Ok, you understand - understood. And he said: we can be: convert the size of the image (of this large jpeg example, say reducing) to match the predefined video frame size. But in this way, we would lose the quality (jpeg - assets). And he says: - or - you CAN use multiple sequences for different sources & when everything is completed (the whole video), I just export it them all as a single project! And I have that a sequence may be getting the DV preset (with the heights of these assets corresponding closely to this preset) and another sequence (in the same project) can be the HDV preset (with the heights of remaining assets corresponds closely to the preset instead). , But he couldn't explain was: how you can view your entire music video (3 minutes) in its entirety in Pro. It seems that when you choose a 2^nd sequence, it obviously creates on the timeline, and assets that you put in the 1^st (DV) timeline is completely separate from the 2^nd (HDV) timeline. And you get no display either at the same time (because they are distinct sequences). 

  So... is this true?

  Are we supposed to use multiple sequences within our project to clip one of the assets with a higher (or other) image size/rate?

  And you export sequences as a final clip?

  And if so, HOW the world watch you your video chats (in the monitor of the project with all of your changes - as you change) when you use more than one sequence?

  Sorry, it seems quite stretched out, but I want to answer your questions you can in turn have for me & be clear so I can finally receive clarity on this topic!

  I know it's much, but if you could address all of the above questions (more background or discussion - is but a handful of issues in there), you have my gratitude... we were afraid to start the part of the video of this project is NOT know what sequence preset start with (as "we don't want to be locked into the wrong choice & waste weeks of editing), let alone a good understanding of the 'why' or the ramifications!

  Thank you so very, very well... You have no idea how...

  Rendering is done on a basis as needed. If we do a complex animation with keyframes, or if they have odd source files, they could do. For keyframe animations, I could make this section of the timeline of a dozen or more times. Otherwise, maybe not.

  Rendering is the production of AV files, just for reading. They take a lot of space and will take a while. It's one of the reasons that a Publisher must familiarize themselves with the WAB (work area bar), so that they do things like rendering for all what they might need. Tip: remember to put this back to the full timeline.

  Good luck

  Hunt

• What are the supported items when you use multiple suites?

  Hi all

  I created a plugin that sends the current path to a url,

  his work very well with debugging in Visual studio 2005 and then it is added to the Adobe Illustrator work only once.

  Its transmission, the path is that for a single file. While I was trying for the second time its does not work

  I use more costumes in my plugin

  AIDocumentSuite

  AIFilePathSuite

  AIActionManagerSuite

  AIUnicodeStringSuite

  AIURLSuite

  I use the "'AIURLSuite ' to call the url and calls the url several times while its used only and its only works once with multiple suites. "

  What are the supported items when you use multiple suites? It is necessary to release all the variables and the suites after completing the task?

  Should they come out in the same order in which they are acquired?

  Thanks in advance

  Farida kaid

  As far as I know, there is nothing forcing you to unleash in the same or in front of the order in which you have acquired in. Frankly, in our plugin gain us once, then lock the plugin to prevent it from unloading and don't release suites when we finished. That said, as far as I know, you should be fine to learn/work/output several times.

• Problem with the format of the values in the command prompt (when you use multiple values)

  Hi all
  
  I have problem with the format of the values in the command prompt when you use multiple values.
  
  Value is year (2009) and when I use it in the drop-down list that is formatted, all right, as 2009, but when I use several values I get number as 2009,00. I put in year column format number with 0 decimal places and save by default in the year column. Year is formatted well anywhere in the query, such as 2009. Why is - what happens at the command prompt when you choose multiple values in prompt dashboard?
  
  Thank you

  I think the YEAR Data Type could be defined DOUBLE RPD.

  Use the CAST function in the formula (fx) and the output from test.

  CAST (INT YEAR)

  Hope, it will help you.