discovered an unknown network under files

Similar Questions

• WiFi connected but unknown network and internet access

  Hello

  I think I've read enough forums and done enough research I finally post my question. My other laptop is Dell Inspiron 1545. It connects to my home network, but says unknown network and no internet access. I tried wifi and ethernet cable. The IP address is set to auto detect, I have reset the router, reinstalled the drivers for the card wifi, without success. Any ideas?

  -Taylor

  Only, I solved this problem on my Dell XPS, so I decided to share with the community.

  After the call to Dell and discover my warranty had expired (a little more than one year) and knowledge it would cost me $129 to get a response from time, I decided to go look for solutions. I found a thread of 2009, attributing the cause to a thing of access network Mcaffee. I knew that's the question because I don't personally like the major anti virus makes (they tend to pull up of stunts like this) so I had ripped my PC McAfee, as soon as I started. But this thread has helped me understand how to solve this problem.

  The problem seems to be an Agent of network access Protection on your system configuration (your start up programs). Make sure it is off. It wouldn't hurt also to try to disable the Internet Explorer ETW Collector Service (has a name shady so I nuked it too: P). this fixed my connection problem not identified immediately.

  Follow these steps (Windows 7):

  1. click on start.

  2. click on search at the bottom bar.

  3. type: msconfig

  4. press enter

  5. you should have a new window named System Configuration

  6. click on the Services tab.

  7. scroll down until you find: Network Access Protection Agent. It will be defined as stopped. It's normal.

  8. uncheck the box next to the network access Protection Agent.

  9. click on OK.

  10. restart your computer.

  Your internet connection should work now. If this is not the case, repeat the procedure until step 6, and then follow these steps:

  1. scroll down until you find: Internet Explorer collector Service to ETW. It will be defined as stopped. It's normal.

  2 uncheck Internet Explorer collector Service to ETW.

  3. click on OK.

  4 restart your computer.

  If these two steps don't fix your problem, go back to the Configuration of the system (Services tab) and it look for any other Network Access Protection Agent, such as Macafee named ones or something similar. Please be aware that uncheck essential services can cause pc problems, so make sure you know what you're unchecking before you do. If in doubt, feel free to google it.

  Another solution would be to temporarily disable your antivirus and firewall and see if that helps. If Yes, then you know where you need to focus.

  Good luck and hope it works!

• I'm trying trying to import my ie Favorites, and there is no option under file to import.

  Just downloaded firefox and there is no option under file to import.

  See

  • https://support.Mozilla.com/en-us/KB/importing%20favorites%20and%20other%20data%20from%20Internet%20Explorer

• Under FILE > OPEN RECENT item (formerly had history of files opened recently; Now it just says: CLEAR. How to restore the history of recently opened?

  REF: NUMBERS > under FILE > OPEN RECENT item (formerly had history of files opened recently; Now it just says: CLEAR. How to restore the recently opened files history?

  If you have numbers in the Dock are trying option-clicking top here.  If you're lucky, you'll see these recent docs there. Use this menu to open and close the docs you want to see in file > open recent.

  SG

• How to remove mediainfo (under file in Windows Explorer).

  I rename files a lot and depend on my shortcut useful and fast Alt_F_M to facilitate this several times a day when I organize things in Windows Explorer.  But recently, I've noticed this useless thing of Mediainfo it sort the shortcut gets stuck.  Of course I could hit the letter M twice, but what I really need to understand, is what determines what is placed on the table of the file (and Edit, View, etc.).  When I D training Mediainfo highlighted is not in the file. Only when the file or folder is highlighted is present in all its glory without glory.  I have search for mediainfo in C drive as drive D, where a lot of my programs residence without success.  Its not in Add/Remove Programs, of course.  Its just a litter from a previous uninstall which is always hanging around.

  It is in the registry?  Group Policy?  Maybe someone could point me in a direction... :))

  Please do not post links Microsoft.  I will never understand them I'm mentally deficient in Microsoft jargon.  Maybe his genetics.  :)

  Just need to know what I'm doing to control what is displayed under these Menu items.  In fact, this raises another point: if I could control what is displayed here, it would be wonderful, and Windows Explorer would be even better than it already is... which is good enough as a file manager.  I tried to Total Commander, but found much more fluid to use Windows Explorer.  Here again, I am a fool.  :)

  Its really amazing how the vast majority of computer users have no idea where everything is on their system.  When I draw to them with things of the Explorer Windows are starting to fall into place in their minds.  Its a shame Microsoft (and Apple is just as guilty as anyone) is not like the default mode to find stuff in the Windows Explorer operating system.  On the contrary, so many people use shortcuts (such as the office!) who just confuse greatly when they really need to find something manually. Then they totally lost.

  I'm this list under files, folders, and online storage.  If this is the wrong category made me know please.

  Hello

  Registry:

  Remove this registry key to remove the entry from the context menu:
  HKEY_CLASSES_ROOT\ * \shell\MediaInfo

  This software allows to remove from windows explore http://softwaretopic.informer.com/remove-mediainfo-from-explorer/

• 802.11 wireless pen drive recognized as 'unknown device' under USB. Help, please.

  Specs: Windows XP Home Edition version 2002, Service Pack 2. This is the version of XP OEM. Processor Intel pentium 4 2.00 GHz. 1.50 GB of ram.

  After an unknown incident (i suspect headphones usb), my wireless USB key has ceased to be recognized as such and become everything simply an "unknown device" under "USB bus controllers. Although windows tells me there is no drivers for the device installed, the wireless pen drive is signed with the Publisher of Microsoft Windows with a version of driver 5.1.2600.0, Microsoft being the driver provider.

  Compound number, the 802.11 device is listed under "Other devices" when 'show hidden devices' is selected and the variable "devmgr_show_nonpresent_devices" entered "environment variables", but is washed out-showing that the system thinks that the device is not currently connected to the computer. In addition, under details, it displays error code 45: the device is not connected to the computer. And it is. It's very hip. as cement and connected tape.

  I plugged the wireless key USB in all the usb ports on the computer, every time with her recognized as 'unknown device' under usb controllers. I entered in the safe mode, uninstalled all the usb controllers and root usb hub drivers and let windows the respawn after reboot in order to solve the problem. No dice.

  I also plugged the USB in a different desktop and it works like a charm, so the issue is not with the hardware.

  Clearly there that a conflict with drivers/registry/God knows what, but I'm at a loss. Somehow, windows has taken its decision and the player associated with "unknown device" and I see no way to make the system "forget" that the USB was never connected. How can I remove the ghost driver "unknown device" manually or force windows to re-associate the key wireless USB with "other devices" (with the yellow? mark) and not this useless usb driver "unknown device"?

  Thanks for the help!

  try to run the following tools in series:

  1. http://support.Microsoft.com/GP/hardware_device_problems
  2. http://support.Microsoft.com/kb/817900 (Microsoft Fix it 50052)

  I suggest you uninstall the drivers for Bluetooth, fingerprint usb controllers and the sensor. Then reboot the computer this should install it the appropriate drivers for it.

  Here's how you can do:

  1. click on the Start button > run > type devmgmt.msc and press ENTER.
  2. locate each USB device, the after another and then right-click on it.
  3. Select the option to uninstall.
  4 restart your computer.

  Alternatively, you can try to install the driver chipset for your computer.

  Hope this information is useful.

  If you get the answer to your question, please go back and mark the reply as an answer while others may find it.

  If you get helped by a response to someone else's question, please indicate the useful post.

  S.Chatterjee

• Centre network and sharing that network discovery, file sharing, and media sharing turned on, should they be on or off? It's on my home computer and I do not share anything

  just noticed on my network and sharing center that the network discovery, file sharing, and media sharing turned on, should they be on or off? It's on my home computer and I do not share anything thank you.

  If you do not share with another PC or XBOX Media Center, then your file and media sharing must be turned off.

• Network that connects to the unknown network will NOT cut

  My computer automatically connects to an unknown network that does not appear on the available wireless networks. It does not disconnect and to log only when I turn off the wireless network. If I connect to another network, it disappears. I can't find any info through the help who can tell me how th shut down my computer to connect to this network. It's windows vista 32 bit

  Try to remove all the networks listed there and restart.

  Network discovery: WE (if you can see other computers)

  All private network (Public's hotspots, airports, etc.)

  What you set security on?
  Rob - bicycle - Mark Twain said it is good.

• network discovery, file sharing and public folder sharing won't turn on if the ethernet cable is removed and plugged

  Public folder of Windows Vista sharing problem.

  Whenever my pc is disconnected from the internet sharing files turns back on. Options: network discovery, file sharing and public folder sharing will turn on if the ethernet cable is removed and plugged. How can I prevent this from happening.

  Hello

  1. Since when are you facing this problem?

  2. don't you make recent changes?

  I suggest you try to perform the clean boot and check if it helps:

  http://support.Microsoft.com/kb/929135

  NOTE: When you are finished troubleshooting, make sure that restore you the computer mode normal startup such as suggested in step 7 of the above article.

  For more information, see this link:

  http://Windows.Microsoft.com/en-us/Windows-Vista/file-sharing-essentials

  It will be useful.

• Printer network under Windows 8.1

  My works Photosmart 4280 old fine with wondows 8.1 through the forum, but having managed to do work with windows 8.1 my other two computers running windows 7 and are wireless will not contact the Photosmart windows 8.1 computer connected by usb. I have the tested network and file sharing, and type of work. I had the controls themselves, made for sharing the printer on all computers. The printer worked fine on the network until I installed windows 8.1. Any help would be appreciated... Thank you.

  Generally, your client machine must use a driver that is compatible with the host computer. Because your host is windows 8.1, your drivers are for windows 8.1, so the previous drivers signal may be different and will not work. Network printing is horrible and has always been. What you can try, deletes the printer completely from your windows machines drivers 7, and there is a configuration of sharing on your machine 8.1, which allows you to specify that drivers can be used, so that you can use older drivers on machines that cannot use the new printer. Once it is setup, you should be able to connect to the printer and windows 7 will get the drivers that are defined in your printer sharing - and then it should work.

  It's very high level and I him did not for a few years as all my printers are wireless now, but I hope this helps.

• All the networks, when connected, display an unknown network without internet access.

  I have a laptop windows 7, and all recently internet my laptop has stopped working. Each network I want to connect to always says that he is an unknown network and that it is connected but has no internet connection. Anyone know what could be causing this? I can't update my drivers, as I do not have to download it from internet. One of my friends recently tried to configure something to its WiFi network via my computer, something in this direction, pourrait it screwed my computer somehow?

  Hello

  Thank you for contacting Microsoft Community.
  Perform the following steps in order:
  1. click on start.
  2. type network and sharing Center , and then press ENTER.
  3. in the left pane, click on change the parameters of the map.
  4. Select the network adapter appropriate (wireless or wired).
  5. right-click on it and click on Properties.
  6. in the Properties dialog box opening, networking, tab scroll down until you see Internet Protocol Version 4 (TCP/IPv4).
  7. select it, and then click Properties.
  8. in the dialog box, select IP address get automatically and DNS server automatically get an address.
  9. go to the next (alternate Configuration) tab.
  10. Select automatic private IP address.
  11. click on Ok.
  12. click on Ok.
  13. repeat the steps for WLAN and wired connections.
  14. now, try to connect to a network and check.
  If the problem persists, click Start-> type cmd-> press ENTER. Type ipconfig/all, press ENTER, and then provide the information displayed there.

• GANYMEDE + peripheral unknown network or Client AAA package

  Hi all

  I can do connect using the set of credentials to the ACS server, log it showed:

  "Reason for failure: 13017 receipt GANYMEDE + peripheral unknown network or Client AAA package."

  I know there are a few changes on GANYMEDE + room for new catalyst IOS, so I consult the guide and it is the end of my config:

  AAA server Ganymede group + TAC_PLUS

  the AUTH server name

  RADIUS server AUTH

  ipv4 10.10.21.251 address

  key xxxxxx

  AAA TAC_PLUS authentication connection group Ganymede + local line

  TAC_PLUS AAA authorization exec group Ganymede + none

  AAA authorization commands 15 default authenticated if

  accounting AAA periodic update 1

  exec accounting AAA TAC_PLUS start-stop group Ganymede +.

  network accounting AAA TAC_PLUS start-stop group Ganymede +.

  connect accounting AAA TAC_PLUS start-stop group Ganymede +.

  My platform is

  -C6500 running on IOS 12.2 (33) SXJ1

  -ACS 5.2.0.26

  Need advice on this subject, thanks

  Noel

  Hello

  What is IP IOS appropriate set to network devices and the AAA Clients for the candidate countries? If Yes, what IP address is indicated on the failure of the ACS that includes the error "GANYMEDE + unknown cover peripheral network or Client AAA? ACS reports as unknown IP address when it is already set appropriately?

  Kind regards.

• Unknown status under ITA

  Hello world

  ITA recently reported 10 servers PE2950 in the unknown state under the Group of servers.  I tried to solve the problem by performing a discovery/inventory of the affected server, unfortunately, the problem persists.

  To resolve this problem, I run the troubleshooting tool and determined that ITA was unable to talk to my server via SNMP.  I restarted the SNMP service on one of the affected servers and then made a discovery/inventory to solve the problem (status is returned to the green).

  Around the same time, I met this "unknown status" issues I have restart my DNS server.  I'm not sure if it was the root cause of the problem, however, I can solve all hostnames after the DNS server has restarted including the 10 affected servers.

  Could you please help me with the following questions?

  -What is the cause of this problem?

  -Do you recommend an easier way to restore the functionality on the remaining servers of unknown status?

  Thank you in advance,

  D

  Message edited by ddasilva99 on 07/05/2008 20:41
  
  

• How will I know when a PDF doc was created originally that there is nothing under file/properties

  How will I know when a PDF doc was created originally that there is nothing under file/properties

  Hi David,

  Generally, it appears in the document properties window in Acrobat (as illustrated in the following snapshot).

  However, if the sender/author has deleted the pdf metadata then there are chances that original file creation date is not displayed.

  

  Kind regards
  Rahul

• Backup point-in-time with backup to network share files

  Hi all

  Oracle Database 11 g Release 11.2.0.3.0 - Production - on Windows 2008R2 64 bit

  I'm still getting hot RMAN backup and that you have configured our backup as follows:

  -Nightly rman backup to local drive (ORAFRA) hot and then copy the entire ORAFRA folder on a network share (which will be on the Strip).

  It adheres to RPO my company (recovery point objective) of 24 hours, because if my real server goes down I can restore in the previous 24 hours.

  HOWEVER, my question is more to be able to make the point-in-time recovery using disaster file sharing network. I guess I can make the point in time at any time prior to my backup complete (using SNA #)... but if I wanted to be able to do point-in-time recovery AFTER my full backup, how would that be possible?

  Example - full backup at 19:00 every night. The incident occurring at 23:00. words I can only return to 19:00 or before. How can I configure I can restore, say at 22:00, using network backup files?

  Thanks in advance!

  Yes.  You must use the syntax for using backup controlfile recovery and do a resetlogs.

  With rman, you might be able to avoid the resetlogs, depending on whether the point-in-time is your real goal (which could be the situation you've lost again them online - or maybe not so rman the controlfile and newspapers archived periodically).

  You might investigate databases in waiting, many places decides that they are worth the cost compared to the possible losses.  And even if you do not, the concepts of recovery help to understand these things.

  You can also consider, the purpose of backup is resumed and rman is to manage the recovery.  It is really important to understand the concepts, to the point you can do it in your sleep (literally nearby, here), but it is also important to understand the tools.