Volume of the computer

Similar Questions

• The speaker volume in the computer sound control mixer is up and works well with the speakers, but with headphones, I can hardly hear.

  Original title: the headphone volume

  How can I activate the volume for headphones? the speaker volume in the computer sound control mixer is up and works well with the speakers, but with the headdphones that I can barely hear

  Hello
   
  1. who is the operating system installed on the computer?
  2. What is the brand and model of headphones?
  3A this works much earlier?
  4. What is the brand and model of the sound card?
  5. have you ever tried to play the Audio using different media player applications and check?
  6. have you tried to connect the headset to another computer or phone and check if it works well?
   
  I suggest you follow these methods and check.
  Method 1: Run the audio troubleshooter.
  Open the Audio http://windows.microsoft.com/en-us/windows7/Open-the-Playing-Audio-troubleshooter playing convenience store
   
  Method 2: Set the earpiece/microphone as default device and check.
   
  a. right click on the volume icon in the system tray at the right corner on the desktop.
  b. Select the playback device, go to torecording tab.
  c. make a right click and headphone/microphone as the default device.
  d. click on apply and ok.
   
  If above steps fails, proceed to method 3.
   
  Method 3: I suggest to disable the improvements and check.
   
  a. right-click on the icon "speaker" at the bottom right of the screen.
  b. Select "playback devices".
  c. right-click on the helmet.
  d. Select Properties
  e. click improvements
  f. check Disable all improvements
  g. click OK
   
  You can read this article for more information:
   
  Tips for solving common audio problems
  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-sound-problems  
  
  You can also contact the manufacturer of headphones and check.
   
  I hope this helps!

• Volume on the computer controls

  I have a windows 7 and the keyboard volume controls do not work how to operate again

  * Proposed by the moderator of "Windows/Windows 7 / Windows Other apps" for "Windows / Windows 7/Hardware & drivers."

  If you try to change the volume of the keyboard, you need to talk or see the instructions that are specific to your particular keyboard model.

  I suggest that you use either the volume of your speakers or the bottom left you screen (a very small speaker).  Just click on the small speaker and drag the cursor upwards or downwards for the volume change.

• Drive C does not appear in the computer management window.

  Hello

  In the window of the computer storage management > disk management, I have see my drive C. CD - DVD drive and an external DVD drive only is displayed. C drive is not there. When I look under the disk defragmentation, the C drive is.

  What gives?

  Thank you

  Hello

  Use the Diskpart utility and check if it lists the C drive. Thelist volume command will provide information about each volume in the computer.

  a. Click Start and then click Run.
  b. now, type cmd in the text box and press on enter to open the command prompt.
  c in the command prompt, type diskpart.exe press ENTER.
  d. Enter the following command in the utility diskpart and press ENTER:
  the list volume

  Check if drive C appears in the list.

  See this article for more information about the Diskpart utility:
  http://support.Microsoft.com/kb/300415

  Kind regards
  Afzal Taher - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• How can I turn the volume on my computer = cannot find the volume indicator

  I lost the sound meter on my Toshiba computer.  I need to increase the volume or check it out because it's quiet.  I used the dial on the front of the computer and is not strong enough yet.  I use to have an indicator in the lower right corner - seems to have disappeared.  Thanks for the help!

  Hedy

  Hello

  ·         Were there recent changes made on the computer before the show?

  I suggest you follow the troubleshooting steps form the article and check if it helps. Also, run the fixit tool and restart the computer and check if it helps.

  System icons do not appear in the notification area in Windows Vista or Windows 7, you must restart the computer

  http://support.Microsoft.com/kb/945011/en-us

• My reading shows the HDMI as a default device, but the sound is yet to come of the computer laptop, even when the volume is turned off on it

  Original title: HDMI sound

  I know that many have had problems, but I did not mine specifically. My HDMI connection was working fine with my laptop HP and m HD tv. I didn't use it for a while, now it is just the video, no audio on the TV. My reading shows the HDMI as a default device, but the sound is yet to come of the computer laptop, even when the volume is turned off on it. Ive read all the reviews and updates of pilot who was old. I don't know what else to do!

  Hello

  System Restore does not have this long period of time.

  You may want to refer to the suggestions in the thread below link and check.

  No sound via HDMI output portable computer connecting to TV

  I hope this helps.

• Can not see the 2nd partition on the computer after using the shrink volume option

  I had 2 partitions on the hard disk the same... but after separate 60 GB unallocated space of 2nd partition (drive D) and after rebooting I don't see my 2nd partition. After that I tried to change the drive letter and path, but it displays the following message 'the operation did not complete because the disk management console view is not updated. Refresh the view by using the refresh task. "If the problem persists close the disk management console, then restart disk or restart the calculation Managerr. I don't want to lose the data.

  Hello

  ·         Have you installed a third-party program like Partition magic on the computer?

  Try these methods further and check if it helps:

  Method 1:

  Try to use diskpart to assign a drive letter to the disk #0 Partition #1.

  (a) click Start Orb > type diskpart

  (b) click right diskpart in the above results > click run as administrator right

  (c) once diskpart load type list volume, press enter

  You should notice that you can see your partition you use for your data, it should not not have a drive letter assigned to it.

  (d) type select volume 6 (replace 6 with the number of the volume assigned to the partition in question)

  (e) type assign letter Z (replace Z with the letter you want to assign)

  When you look in the computer, you should be able to see your score.

  Method 2:

   

  I also suggest that you run the Microsoft fixit tool and check if that helps:

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 3:

  You can follow the steps in troubleshooting section below and check if it helps:

  http://support.Microsoft.com/kb/2001877

• Lost my icon of audio, now I can't control the volume on my computer

  Hello

  I am unable to turn on the sound on my computer icon. I can't reduce or increase the sound. How can I turn on system icon.

  Thank you

  Hello

  Did you change your computer before this problem?

  Follow the suggestions and see if it helps.

  Method 1

  See the article and then check.

  Change icons appear in the notification area

  http://Windows.Microsoft.com/en-us/Windows7/change-how-icons-appear-in-the-notification-area

  Method 2

  Follow the steps in the article.

  System icons do not appear in the notification area in Windows Vista or Windows 7, you must restart the computer

  http://support.Microsoft.com/kb/945011

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following windows Help article.
  Back up the registry
  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  See also:

  Adjust the sound level on your computer

  http://Windows.Microsoft.com/en-us/Windows7/adjust-the-sound-level-on-your-computer

• I'm trying to re - install the xp on the computer operating system, I get the message that the volume is in use by another process, how do I disable the other volume process so that I can proceed?

  I have xp os on the computer, the computer is very slow, I thought that a re - install help?

  http://michaelstevenstech.com/XPrepairinstall.htm
  or
  http://michaelstevenstech.com/cleanxpinstall.html

• Sound does not work on the computer and the volume icon does not appear in the system tray.

  Original title: my sound icon has disappeared from the taskbar.  The Control Panel indicates the sound is on, but I can't hear anything.  What happened and how do I get my sound back?

  Have a Toshiba laptop that always displays the lower icon audio in the right hand of the screen.  The sound icon has disappeared and I can't hear anything.  I check Contol Panel and sound, and he says it works and is turned up... but I can't hear a thing.  How can we retrieve icon of audio and how I can hear sound?

  Hello

  Thank you for your response.
  I did a "System Restore" and the icon reappeared, and the sound now works.
  I restarted the computer a couple of times, but that does not solve the problem.  Also, I went into the Panel and checked to see if the speakers were working and were lit, and they were.
  It wasn't until I did the restore of the system that the icon reappeared and the noise began to work again.
  Thank you.

• How to adjust the volume on this computer at maximum volume

  my laptop volume is very low.  I'm trying to maximize volume

  Apart from turning up the volume, there's not much you can do.  Some laptops have very weak speakers.

  However, you can try this:

  1. From the desktop, right click on the volume near the clock icon, then choose playback devices.
  2. Double-click the playback device (probably speakers).
  3. Under the tab highlighted, locate and resolve any improvement that could help.  These options vary depending on the manufacturer of your system and what features and functions is supported by their system.

• HD is full, but there is no files on the computer

  Hi, I've been struggling with this problem for quite a while now. I can't seem to find anything online that actually works, I hope someone can help.

  I have an iMac 27-inch retina display, 1 TB HD. I look on the storage and the other section of the computer takes more than 850 GB, how is this possible? I have next to no file on the disk hard because I'm always working from the external hard drive, I emptied the trash so I know it's clean, I tried "erasing free space" in the utility application disc, but towards the end it always come with the disc full boot, then when the process is complete I get the error message "cannot create the temporary file.

  I am a Publisher so I use photoshop and Premiere Pro a lot, would it something to do with these programs?

  Thank you

  Dan

  For the other category in the display of information storage, see this support article. If the display appears to be inaccurate, try to rebuild the Spotlight index.

  Empty the trash if you don't have it already done. If you use iPhoto, emptying his trash internal everything first:

  ▹ iPhoto empty the trash

  In pictures:

  ▹ Show of the recently deleted ▹ file delete all

  Do the same thing in other applications like Aperture, with an internal feature of the trash. Then, restart the computer. Temporarily, which will free up space.

  According to the documentation from Apple, you need at least 9 GB of free space on the boot volume (as shown in the Infolog) for normal operation, not the mythical 10%, 15% or any percentage. You also need enough space to allow the growth of the data over. There is little or no advantage in terms of performance to get more free space than the minimum Apple recommends. Storage space you'll never use is wasted space.

  See this support article for some easy ways to free up storage space. A common waste of space is old backups iTunes to mobile devices. As shown in this support article, select the devices tab in the iTunes preferences window, select the backup that you want to remove and click on delete the backups. Keep at least a backup of each device you use yet.

  You can, if you wish, use a tool such OmniDiskSweeper (ODS) to explore the volume and discover what is take up space. You can also delete files with it, but not unless you don't know you know what you remove and that all data is stored safely. This means that you have several backups, not one. Note that the ODS only works with OS X 10.8 ("Mountain Lion") and later versions.

  IMPORTANT: This comment is neither a recommendation nor an endorsement of any third party software. You should always do your own research to determine if the unknown software is safe and useful. Don't take the word of anyone, including mine.

  Deletion of files inside a photo library or iTunes will damage the library. Such a library should be changed within the application that created it. It is the same for e-mail files.

  Go further than if the problem is not resolved by the steps above.

  ODS cannot see the whole file system when you run simply by double-clicking; He sees only the files that you have permission to read. To see everything, you must run it as root.

  Back up all the data now.

  Install the application in the Applications folder as usual. Quit it runs.

  Triple-click any where in the text line below on this page to select, then copy the selected text in the Clipboard by pressing Control-C key combination.

  security execute-with-privileges /A*/OmniDiskSweeper.app/*/M*/* 2>&-

  Launch the Terminal application integrated in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  Paste in the Terminal window by pressing command + V. You will be asked for your login password.

  The application window opens behind other open windows. When you scan a volume, the window will finally show all files in all folders, sorted by size. It may take a few minutes for the app to finish scanning.

  I do not recommend that you make a habit of doing. Do not delete anything as root. If something should be deleted, make sure you know what it is and how it got there, and then remove by safer alternatives. If in doubt, leave it alone or ask for advice.

  When you are finished with the app, he quit and also to leave Terminal.

• NB520, NB550D - how to set the volume to the State of sleep and music?

  I'm looking for an opportunity to adjust the volume to the State of sleep and the music...
  The mere fact that I noticed is that volume depends on the defined level when the computer was working. But how do I change the State of sleep and the music when the comp is off swich?

  Hi communication,

  I checked the user manual and found the following information:
  The volume control and mute setting may be different between the Windows mode and the mode of sleep and the music. Before connecting the audio device to the computer, turn down the volume of the audio device. Sound quality can also be different.

  So based on this information, you will need to adjust the volume in Windows, but it might be a little different. I have not found any information on the change of volume in sleep mode and music.

• Apple pro no keyboard no Volume or the eject button

  Hello

  I'm running OS X 10.5.8 on an EMac with the original Apple Pro Keyboard.

  The OS X install is a fresh, as installation when I got the computer it was protected by locked.

  No matter what I do, the eject button and the Volume buttons above the numeric keypad on my "Apple Pro Keyboard" do not work.

  The volume buttons seem to work a bit in iTunes, if I press and hold the button for a very long time.

  I tried the keyboard on my MacBook Pro, and it works very well.

  I also tried a Kensington Slim Mac on the Emac and after keyboard through the wizard keyboard and unrecognized, which worked well as well (including the Media Eject keys and Volume).

  I tried to do a reset of the PRAM on the Emac, but this doesn't seem to be a facility of this computer.

  The EMac is a special eBay and only cost me $10 ;-), but it seems to work fine apart from this question.

  Please help me solve this problem, because it drives me crazy.

  Hello

  Can try this to eject an icon at the top right of the screen...

  On your main hard drive, dig in the System > Library > CoreServices > Menu Extras. Inside this window, double-click the icon called Eject.menu.

  http://www.CreativeTechs.com/tips/quicktips_51.html

• HP ENVY laptop - 15 - ae101no: control of the Volume on the keyboard keys do not work!

  Hello

  Volume control keys had suddenly stopped working, and I have no idea why. I have the model HP ENVY laptop - 15-ae101no (ENERGY STAR). Could you please help me fix it? Thank you!

  Hello

  Try the following.

  Download Realtek HD Audio Installer on the link below and save it in your downloads folder.

  http://ftp.HP.com/pub/SoftPaq/sp74501-75000/sp74867.exe

  When finished, press and hold the Windows key and press R

  In the run window, type devmgmt.msc and press to enter.

  In Device Manager, expand sound, video and game controllers.  Right click on the Realtek device and select uninstall - also, you should get a command prompt to delete the current driver, check the box allow this and then proceed to uninstall.

  When you are finished, download and reinstall the Chipset driver at the following link.

  http://ftp.HP.com/pub/SoftPaq/sp72001-72500/sp72105.exe

  When the reinstallation of Chipset is finished, stop the laptop.

  Disconnect the power adapter and then hold button power supply for 30 seconds, then release.

  Plug the power adapter.

  Robinet tap away at the key esc that you start the computer to launch the Start Menu, and then select f10 to open the bios menu.  Press f9 to load the default values (sometimes it is f5, but the menu below indicates the correct key), use the arrow keys to select 'Yes' and press ENTER.  Press f10 to save the setting and still use the arrow keys to select 'Yes' and press on enter.

  When windows has reloaded, open your download folder, right click on the installer of Realtek and select "Run as Administrator" to launch the installation.  Once this done, reboot the laptop and let windows load completely for a few minutes before checking.

  Kind regards

  DP - K