VPN 3015 terminal settings

Similar Questions

• Change to the subject: the configuration via the mac terminal settings

  Hello

  I administer more than 140 computers mac, with firefox installed. Unfortunately, it seems like a daily appearance when a user calls and says that firefox is updated, listen to which they can't because they are not administrator accounts.
  Now, I use apple remote desktop to turn off auto-updated for many other applications such as software update, microsoft office and adobe. Unfortunately since firefox does not use a standard plist file on mac I can't use default to write preference remotely.
  Question: Is there a way to write to the config of firefox via command line, so I can turn off auto-updated mass instead of having to touch to each computer and do change in the GUI?

  Thank you!

  Use a mozilla.cfg file in the Firefox program folder to lock the prefs or specify default values.

  Place a local file - settings.js in the folder by default/pref where you will also find the channel - prefs.js to specify using mozilla.cfg file.

  pref("general.config.filename", "mozilla.cfg");
  pref("general.config.obscure_value", 0); // use this to disable the byte-shift
  

  See:

  • http://KB.mozillazine.org/Locking_preferences

  You can use these functions in mozilla.cfg:

  defaultPref();  // set new default value
  pref();         // set pref, but allow changes in current session
  lockPref();     // lock pref, disallow changes
  

  lockPref("app.update.enabled", false);
  

  • http://KB.mozillazine.org/app.update.enabled

• 3015 VPN concentrator

  Whenever I try to add a new local network connection to local area network, a vpn 3015 concentrator, I get the following error:

  "Unable to parse the source IP address."

  My options are again or go to the home page.

  Does anyone know what is the problem?

  Thank you

  Pat

  You get this when there is an error in the fields in the L2L configuration section. Check the LAN section, you must either specify a list of network (and make sure that this list has something in it), or specify a subnet and subnet mask in the two fields below.

  It's basically tell you you have not filled in the fields correctly, so check everything and it should disappear.

• VPN configuration blocking Internet connectivity

  I own an iPhone6 (bought in November 14 and another iPad4 (bought in early 2014) - I face a problem even in both devices.)

  Whenever I'm trying to be devices connecting to the Internet (this either through Mobile or wireless data, I have to take concrete steps to start-up the VPN setting without which the device connect to the Internet. However sometimes (although not very often) the VPN configuration gets turned on by itself without manual intervention (on start-up or mobile data or WiFi on the device). So there is always some delay time in the connection to the Internet whenever I want to use the device.

  I would be grateful for suggestions from the community in order to overcome the problem.

  You have installed VPN software or you have configured in your VPN settings? If you have a VPN configuration, then check its configuration. If you do not have a VPN configuration or a VPN software installed, then the VPN switch in settings should not illuminate.

• How to enable VPN on iphone 4?

  Hello all, in fact I installed a vpn application on my iphone but after when I went to the

  The iPhone settings, I found their vpn option in settings > general > vpn, so now I want to know who

  How does the iphone vpn is - even as the applications available on the store for the iphone and how to configure

  I have no idea what to do what should I fill in the vpn options available when we try

  TO enable vpn on iphone?

  VPN:

  A virtual private network (VPN) extends a private network by a public network such as the Internet. It allows users to send and receive data on shared or public networks as if their computing devices were connected directly to the private network, and benefit the functionality, security and private network management policies. ^[1] A VPN is created by connecting virtual point to point through the use of dedicated connections, virtual, tunneling protocolsor encryptionof traffic.

  Wikipedia

  Better find you the developer's Web site and see what they can do with their application.

• How can I configure VPN to allow someone to see my local network but use their own internet?

  OK, I have the VPN all the settings and it works decently, but one thing I really want I can't understand.
  When 'Default gateway to use on a remote connection' is checked in the customer then remote users can connect to the vpn, access in the right subnet and to access the internet

  When it is not enabled, users cannot access the computers on the subnet (other than the remote desktop to the vpn Server itself using the local IP address), but they can access the internet through my network.
  If it is checked and then access the internet through my network and subnet.

  What I would like is to be able to have users access the subnet as if they were here, but use their own internet for everything else.
  Who is? What Miss me to make it work?

  OK, I have the VPN all the settings and it works decently, but one thing I really want I can't understand.
  When 'Default gateway to use on a remote connection' is checked in the customer then remote users can connect to the vpn, access in the right subnet and to access the internet

  When it is not enabled, users cannot access the computers on the subnet (other than the remote desktop to the vpn Server itself using the local IP address), but they can access the internet through my network.
  If it is checked and then access the internet through my network and subnet.

  What I would like is to be able to have users access the subnet as if they were here, but use their own internet for everything else.
  Who is? What Miss me to make it work?

  Hi, Talkingscientist,

  Try this

  Linksys

  http://TechNet.Microsoft.com/en-us/library/cc302437.aspx

• Connect to a Terminal Server

  I have three computers at home.  Windows XP, Windows Vista Home Premium and a netbook, that I just bought a Windows 7 starter.  All are on Norton 360.  One with Windows Vista cannot connect to my desk at work, a VPN server terminal.  I can connect fine with XP and 7 Starter.  I took the computer to my COMPUTER service and that they could not understand it.  I have configured my security at the lowest and still unable to connect.

  Hi AlleeSavor,

  The question will be more suited in the TechNet forum. As such please post your concerns in the said forum for a better supported.

  Click on the link below to browse the forum.

  http://social.technet.Microsoft.com/forums/en-us/categories

   
  Nice day.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Switch Cisco 2960/3560 = > recovery password and default settings with the button Mode

  Hi Experts,

  I have some confusion with the button Mode with cisco 2960/3560 switches.

  I read on many forums and articles, but where things are not clear.

  a place given 3 seconds and somewhere is given 7 or 10 seconds.

  Qus1), what is the exact time to press/hold Mode button to perform two following tasks:

  A. password recovery (according to my knowledge 3 sec) good or bad?

  Configuration of the switch (start + run) would be safe

  After the recovery of password? Yes or no

  B. factory default (according to my knowledge 10 dry) good or bad?

  I'm afraid, because if I press mode button more than 3 seconds, then

  It will delete any configuration of cisco switch. Yes or no

  Qus2) I want to recover the catalyst 2960/3560 switch password without

  Start/run configuration to lose. That is my main concern.

  Please tell me how to do this, what will be the time keeping Mode buttom

  in a few seconds?

  Qus3) which means this line

  "If the password recovery mechanism is disabled in switch

  then you will lose all the config.

  This sentence has been given on this forum url

  https://supportforums.Cisco.com/thread/140848

  KS

  Attach a terminal or PC with terminal emulation (for example, Hyper Terminal) port console switch.

  Use the following terminal settings:

  • Bits per second (baud): 9600

  • Data bits: 8

  • Parity: None

  • Stop bits: 1

  • Flow control: Xon/Xoff

  Note: For more information on the wiring and connection of a terminal to the console port, refer to connecting a Terminal to the Console Port of Catalyst switches.

  Unplug the power cable.

  The power switch and take it to the switch: command prompt:

  2900XL, 3500XL, 2940, 2950, 2960, 2970, 3550, 3560, and 3750 switches of the series, to do this:

  Press and hold the mode button located on the left side of the façade, while you reconnect the power cable from the switch.

  2960, 2970

  Release the Mode button when the SYSTEM LED flashes orange and then turns green. When you release the Mode button, the SYSTEM LED flashes green.

  3560, 3750

  Release the Mode button after about 15 seconds when the SYSTEM LED turns green. When you release the Mode button, the SYSTEM LED flashes green.

  The system was interrupted before the flash at the end file system initialization

  loading the operating system software:

  flash_init

  load_helper

  boot

  switch:

  Run the flash_init command.

  switch: flash_init Initializing Flash... flashfs[0]: 143 files, 4 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 3612672 flashfs[0]: Bytes used: 2729472 flashfs[0]: Bytes available: 883200 flashfs[0]: flashfs fsck took 86 seconds ....done Initializing Flash. Boot Sector Filesystem (bs:) installed, fsid: 3 Parameter Block Filesystem (pb:) installed, fsid: 4 switch: !--- This output is from a 2900XL switch. Output from !--- other switches will vary slightly.

  Run the load_helper command.

  switch: load_helper switch:

  Question the dir flash: command.

  Note: Be sure to type a colon ":" after the dir flash.

  Appears in the file system of the switch:

  switch: dir flash: Directory of flash:/ 2    -rwx  1803357                  c3500xl-c3h2s-mz.120-5.WC7.bin !--- This is the current version of software. 4    -rwx  1131                     config.text !--- This is the configuration file. 5    -rwx  109                      info 6    -rwx  389                      env_vars 7    drwx  640                      html 18   -rwx  109                      info.ver 403968 bytes available (3208704 bytes used) switch: !--- This output is from a 3500XL switch. Output from !--- other switches will vary slightly.

  Type rename flash: flash: config.old config.text to rename the configuration file.

  switch: rename flash:config.text flash:config.old switch: !--- The config.text file contains the password !--- definition.

  Issue the boot command to boot the system.

  switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC7.bin"...############################### ################################################################################ ###################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC7.bin" uncompressed and installed, entry po int: 0x3000 executing... !--- Output suppressed. !--- This output is from a 3500XL switch. Output from other switches !--- will vary slightly.

  Enter "n" at the prompt to abort the initial configuration dialog box.

  --- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Continue with configuration dialog? [yes/no]: n !--- Type "n" for no. Press RETURN to get started. !--- Press Return or Enter. Switch> !--- The Switch> prompt is displayed.

  At the switch prompt, type en to enter a mode.

  Switch>en Switch#

  Password recovery

  Type rename flash: config.old flash: config.text to rename the configuration file with its original name.

  Switch#rename flash:config.old flash:config.text Destination filename [config.text] !--- Press Return or Enter. Switch#

  Copy the configuration file in the memory.

  Switch#copy flash:config.text system:running-config Destination filename [running-config]? !--- Press Return or Enter. 1131 bytes copied in 0.760 secs Sw1#

  The configuration file is now reloaded.

  Replace the current passwords that you do not know. Choose a password with at least one capital letter, one number and one special character.

  Note: Replace passwords that are required. You must crush not all passwords listed.

  Sw1# conf t !--- To overwrite existing secret password Sw1(config)#enable secret !--- To overwrite existing enable password Sw1(config)#enable password !--- To overwrite existing vty password Sw1(config)#line vty 0 15 Sw1(config-line)#password Sw1(config-line)#login !--- To overwrite existing console password Sw1(config-line)#line con 0 Sw1(config-line)#password 

  Write the running configuration in the configuration file with the write memory command.

  Sw1#write memory Building configuration... [OK] Sw1#

  For factory reset:

  do not give under the control of factory reset

  Switch#copy flash:config.text system:running-config

  can I copy the running configuration to Flash

  Switch flash running-config #copy:

  Destination file name [running-config]?

  Building configuration...

  [OK]

  Switch #copy running-config startup-config

  Name of destination file [startup-config]?

  Building configuration...

  [OK]

  Review the link for more information below

  http://www.Cisco.com/en/us/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml

  Please note the useful messages.

  Concerning
  Vesta
  "Everybody is genius." But if you judge a fish by its ability to climb on a tree, he will live his entire life, believing that this is stupid. "

• Limitation of certain groups in the field of NT to VPN in the network

  I set up our VPN 3015 for their our NT domain authentication. My question is. Is there a way to limit authentication to a global group in the domain. For example I want to limit to only users who are in the world group "VPNACCESS" to access our vpn...

  If you have a user with the correct information and a user/pass valid on the NT domain, they will be able to connect. Since you do not know which ip address your customers come over that probably, you don't really power limit via the hub. Unless you put this information on another device, his is not going to be possible. You could use the local database on the hub for authentication or send it to a radius server if you want to restrict users. If there is nothing, it will be on your global group on your server permissions.

  Kurtis Durrett

• Unable to connect to the internet and VPN in the network.

  I have an ADSL account and when I vpn in our network using cisco VPN 3015 vpn client can't access the internet more locally. I have to use our internal proxy server on the network. Is it possible to make the vpn tunnel but also use the local internet DSL for browsing connection?

  You must set up split tunnelling tunnel, while only some packets are sent through the tunnel, the rest get out in clear packages just as usual.

  In 3015, create a list of network under Config - Mgmt policy - traffic Mgmt - list networks, this list includes your internal networks (you want to be dug traffic). Then go under the group to which the client connects to, on the Client configuration tab, select only the network of tunnels in the list, and then select your list from the drop-down list box. Reconnect and're you good to go.

  Keep in the spirit of split-mining is considered a bit of a security risk because your PC is now accessible from the Internet AND you have a VPN directly in your internal network. If someone can take possession of your PC, then they have access to everything. You can also watch in allowing both client firewall stuff.

• Version 4.0 Client VPN via a DSL connection

  Hello.

  In my corporate network, I have configured a PIX 520 firewall with vpn configuration, then, when I am connected via dial-up connection there is no problem,

  but I have a DSL connection, a DSL router, the router ethernet workshop has the 192.168.1.1 ip address with my PC the IP 192.168.1.3 is mandatory that I must have a public ip address for my PC with the VPN client software?

  because I have problems, and the message displayed by the software is: "secure VPN connection terminated locally by the motif client: the remote peer not responding."

  is there a problem with the NAT (in my DSL provider's network? I need a static mapping to a public ip address?,)

  Thanks for help me.

  If you have v6.3.x fw pix, nat/pat is not going to cause a problem, it will automatically negotiate UDP encap.

  THX

  AFAQ

• with 2 levels of firewall VPN remote access

  We have two firewalls of different suppliers, with the first level being a cisco firewall. The Setup is:

  ISP <-->(router) <-->(Cisco Firewall) <-->(another firewall of the seller) <-->LAN internal

  We need to give remote users (with installed VPN clients), internal access to certain resources in the local network.

  My question, where can I configure my IPSec VPN, for best security practice, given that my router, Firewall-1 & Firewall-2, all take care the VPN features.

  I also want to allow remote users (who are they assigned local IP internal IP pool), to allow to specific resources (servers read) & specific ports.

  So can implement an access list, after that the VPN is terminated & users get their local pool IPs?

  Thank you & best regards

  MD

  Hello, MD,.

  What is the version of the code that you run on your PIX? If you run version 6.x of the code, then you will not be able to use the vpn-filter command to restrict access to certain IP addresses.

  You should run version 7.x for it where you can specify an ACL to restrict traffic.

  In addition, only some PIX firewalls can be upgraded to version 7.x, please look in the link given below

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_qanda_item09186a00805b87d8.shtml#Q1

  If you can not pass the PIX to version 7.x, then you will need to use another VPN device.

  Hope that answers your questions. Rate this post if it helped.

  See you soon,.

  Gilbert

• VPN Concentrator at the migration of ASA - auth problem.

  Hi all

  I'm migrating to remote access VPN (IPSec) VPN 3020 to ASA. Local authentication works very well. If I add the IAS radius for authentication servers, then I get the following error message

  Secure VPN connection terminated by a peer.

  433 reason: (reason unspecified peer)

  The capture of shows "access-reject" in back IAS server packages. IAS server is configured in the same way as the VPN 3020.

  I run the code to 8.0 (0) on the SAA. Any idea of what is the cause?

  Hello

  You specify the shared secret between asa and IAS?

  You specified in RADIUS server that ASA is allowed to send requests? In other words has specified that the SAA is a valid SIN?

  This link may be useful: http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00806de37e.shtml

  I hope this helps.

  Best regards.

  Massimiliano.

• ASA-to-router VPN, private, public

  I have a setup where a customer will send calls to a Complutense University of MADRID, from a private address, through a VPN tunnel Terminal to a 2811. The call to hit a SBC that caters to the public and is located just behind the router on FE0/1. (See photo)

  Traffic through the ASA is to be exempted from NAT.

  Since it is all public on my end and my waypoints by default for the router of my ISP, I guess I don't have anything other than a default route. (I'm not under routing protocols - just a static outgoing route)

  The tunnel does not come to the top. In fact, I never see that no traffic hit my side in all. Does anyone have experience making a private VPN, or know an example of config anywhere?

  This is my Bill at the end of the config:

  crypto ISAKMP policy 4

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  lifetime 28800

  ISAKMP crypto key XXXXXXXXXX address (public #1) No.-xauth

  Crypto ipsec transform-set esp-3des esp-md5-hmac XXXSET

  XXXMAP 4 ipsec-isakmp crypto map

  defined by peers (public address #1).

  Set the security association idle time 3600

  game of transformation-XXXSET

  PFS group2 Set

  match address 170

  access-list 170 permit ip host (public address #3) 10.0.0.5

  interface FastEthernet0/0

  IP (public address #2) 255.255.255.252

  load-interval 30

  Speed 100

  full-duplex

  No cdp enable

  card crypto XXXMAP

  service-policy output AutoQoS-policy-UnTrust

  Thank you

  Paul

  Your configuration looks very good.

  Phase 1 comes up when you try to pass traffic through? "cry isa to show her.

  Back P1, P2 comes up? "See the crypto ipsec his | I ident | SPI | BA | desc ".

  If none is coming, run a debugging:

  debugging cry isa

  debugging ips cry

  See if the tunnel is initiated when traffic is sent. As long as you have a default route pointing outgoing and don't have any other way, you should be fine. Looks like everything will be a connected network.

• VPN error

  I set up a vpn ipsec/ike on my (515E) cisco pix, ASDM version is 5.2 (3), PIX version 7.2 (1) and activate IPSec NAT - t

  When the VPN connection, authenticate via TACAC +, it works fine...

  However, now I try to configure it so that it will authenticate the LDAP authentication with the domain (microsoft) and gives this error code...

  "Secure VPN connection terminated by Perr. 433 reason: (reason unspecified

  peer)"

  any idea?

  Thank you

  Rachel

  Rachel,

  What is shown in the logs of your domain server?

  You've seen the example config for LDAP auth below: -.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a008060f261.shtml

  HTH >