VPN breaks with different ISP
I've been running an IPSec/GRE of hub-and-spoke base tunnel network use the same ISP in all locations for several years without problem. I use 1721 routers remote offices and a PIX on the hub site. All traffic, including browsing the Internet is routed through the hub site a PIX/WebSense combo where URL filtering. Recently, we started to migrate to a new service provider. I reconfigured two remote sites to use the IPs and T1 new Internet service providers. I don't have to make any changes to the configuration of IPSec/GRE and new tunnels of office seem to be fine. However, when users began to go immediately, they noticed the some, only some, websites would not be responsible. The browser would simply wants to "loading page". Funny it is that applications that remotes struck Central will work perfectly and also, many websites will work perfectly. Immediately, I assumed a MTU problem and started to lower the MTU of the new tunnels. I went all the way to a ridiculously low MTU 768 and no luck. At this point I don't know what to try next. I have temporarily re-routed the remote PC directly from their T1 to relive the problem but I need to get them routed back through the hub, so we can filter URLs. What can try fix here?
Thank you
Diego
Hi Diego,.
Have you tried to use the command of setting-mss tcp ip on the routers from 1721 to adjust TCP segment size?
Take a look at this address for more details, it can help you here.
http://www.Cisco.com/en/us/products/SW/iosswrel/ps1839/products_feature_guide09186a00804247fc.html
Andy
Tags: Cisco Security
Similar Questions
-
Creating remote VPN redundancy with 2 ISPS on ASA 8.3 running
Hello
I need help in implementing connection remote VPN with two ISPs (redundancy), so that the remote VPN client will be only one connection, but two ISPS will be linked to another.
I can do it on previous IOS, but things have changed in ASA 8.3, please help.
Hello
If you follow the post, you will find that the "tunnel-group" is a global command that is not set to a specific interface.
Basically, must be added the card encryption even for two interfaces, as follows:
backup_map interface card crypto outside
backup of crypto backup_map interface card
crypto ISAKMP allow outside
ISAKMP crypto enable backup
The only difference is related to the statements of NAT, reason why I included the pre - NAT post in my previous note.
Thank you.
-
Site2site two vpn "Server" for two different ISPS
Hello. I have two lines of two different ISPS. Both are 4 / 4 Mbit/s leased lines. I want to create a vpn site-to site with a few points of end for each of them. I have ASA 5540 firewall as a VPN endpoint on my network. My question is. I have two different VPN? Can I create two outside interfaces and use each one for each ISP one here to create my VPN? I first thought of contexts, but I abandoned em as soon as I saw that there's no VPN with contexts.
Thanks in advance.
Simple topology is
VPN - RTR - ASAOut1 VPN1ISP
-ASAOut2 VPN2ISP
Hello
I understand that you need create a tunnel between ASA 1 and 2 of the ASA with an ISP and the other tunnel on ASA 2 other ASA 2 ISPS.
It is possible as long as you take care of the delivery. For the remote access clients it will end interface ehich has the default gateway.
-
Unable to access the local network with VPN with some ISPS
Hello
We have a VPN Remote Access IPSEC with an ASA5505. Install VPN it correctly but can not access the inside or the ASA to my office.
But at home with another Internet service provider, it works! You can access inside.
We are trying with other ISP and it works with 2 and does not work with the other 2!
Office we also have an ASA5505, but we have another VPN other sites that work properly.
Any ideas?
Thank you and sorry for my English.
Add...
ISAKMP nat-traversal crypto
That should do the trick! Please rate if this can help.
-
How to connect 2 different adsl2 + line by different ISP
How to connect 2 different adsl2 + line by different ISP. We have two LANs, but we have just a printer and we want to share this printer. We have two different line ADSL but different ISP. How can we achieve this?
Hello
It is necessary to create the VPN connection.
You have Windows XP Professional where your printer is installed and connected?
If so, you can create VPN server in Windows XP Professional PC, wherever your printer is connected. Here's how:
http://www.zdnetasia.com/configure-Windows-XP-Professional-to-be-a-VPN-server-39050037.htm
Then, you need to configure modem ADSL (corresponding to your printer) - set port forwarding for port 1723 (PPTP) to the computer with the VPN server.
You have to find your public IP address of the network where is installed printer - you can see in the ADSL modem (from configuration pages WWW) or open this page in the computer where is installed your printer:
and you will see your public IP address.
Then what to do – change one different internal subnet network - if one network has 10.0.0.0/24 second network must have another network addressing, for example, 10.0.10.0/24.
And now set up connection on the computer you want to print - create the VPN connection to connect to the VPN server:
http://support.Microsoft.com/kb/314076/en
item 11. -write the public IP address.
Name and password - use the user and the password of computer with WinXP Pro VPN server, which has the permition to incoming VPN connections.
After successfully completing the VPN connection - click on Start - run and write \\x.x.x.x , where x.x.x.x is the IP address of the computer with printer and click OK. You'll see printers and shared files. Choose the printer share name and click on the name - the printer will install the drivers and then you can print a test page to the printer print test.
LC
-
Original title: how to find missing or corrupt files on windows xp pro
I just bought a webcam logitech c110 and whenever I try to install the installer breaks down and I was doing the blue screens with different messages on them... How to scan for missing or corrupted files? My brother-in-law has built this computer for me and I did not all disks for windows xp pro. system that is on it
Hello
1. you receive an error message while trying to install the webcam? If so, then post back the exact error message.
2 are you able to install any other software?Try to capture the error message on blue screen and after return the exact error message. This could help us help you better.
Step 1: Try to install the webcam software in clean boot state and check.
From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".
Reference:
How to configure Windows XP to start in a "clean boot" State
http://support.Microsoft.com/kb/310353When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
1. click on start and then click Run.
2. type msconfig and click OK.
The System Configuration Utility dialog box appears.
3. click on the tab general, click Normal Startup - load all services and device drivers and then click OK.
4. When prompted, click on restart to restart the computer.Step 2: Look for error messages in the event viewer. If you find error messages after return the exact error message so that we can help you better.
Reference:
Using the event viewer
http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/snap_event_viewer.mspx?mfr=trueUnderstanding of event viewer
http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/event_overview_01.mspx?mfr=trueProcedure to view and manage event logs in Event Viewer in Windows XP
http://support.Microsoft.com/kb/308427 -
use different JADs to deploy a COD with different properties
I've never had different JADs to work for the Web site deployment.
This is the problem, I use getAppProperty MIDLET to get a property.
I create a file myMidlet.COD with myMidlet.jad which has a property of the HOST.
I have ten different JADs with different HOST property on a Web site for
a myMidlet.COD that will be deployed. The midelt deploys nicely on the Blackberry
but the HOST is the same as that used to build cod. They gave me a code snippet and
added some debug statements to see what this thing of Module
public class mybbProperty {}
CodeModuleGroup [] allGroups;
CodeModuleGroup myGroup = null;
String moduleName;
Boolean flag = true;public void mybbProperty() {}
}public void init() {}
versForm.debugtext += '\n init';AllGroups [CodeModuleGroup] is CodeModuleGroupManager.loadAll ();.
versForm.debugtext += "\ngroup;
moduleName = ApplicationDescriptor.currentApplicationDescriptor () .getModuleName ();
versForm.debugtext mode += "\n" + moduleName; Note ModuleName is correct and is "myMidlet".for (int i = 0; i)< allgroups.length;="" i++)="">
versForm.debugtext += "\n"+allGroups[i].getFriendlyName ();If (allGroups [i] .getFriendlyName () .equals ("myMidlet")) {}
versForm.debugtext += "\n"+allGroups[i].getFriendlyName ();
versForm.debugtext += "' \n * found"; "
for (Enumeration e = allGroups [i] .getModules ();)
e.hasMoreElements () {}
versForm.debugtext += "\n *"+ e.nextElement (); "
}
myGroup = allGroups [i];
break;
}
for (Enumeration e = allGroups [i] .getModules ();)
e.hasMoreElements () {}
versForm.debugtext += "\n *"+ e.nextElement (); "
// }If (allGroups [i] .containsModule (moduleName)) {}
myGroup = allGroups [i];
break;
}
}
versForm.debugtext += "\n end";}
public String getAppProperty (String name) {}
If (flag)
init();
flag = false;
versForm.debugtext += "\n getAppProp"+ name;
If (MyGroup is nothing)
Returns a null value.
Return myGroup.getProperty (name);
}
}I use the function mybbProperty.getAppProperty ("AppMyHost");
I noticed that the getFriendlyName() is the name of my Application, so I use it and
print information. Did I get this
mybbProperty mybb = new mybbProperty();
String s = mybb.getAppProperty ("AppMyHOST");
myMidlet
* Found
* myMidlet-3
* myMidlet-2
* myMidlet-1
of course, which returns null. So how do JAD another properties which was used to deploy the
App for Blackberry. In Nokia its pretty simple use MIDlet getAppProperty() you need a jad and jar for
deploy it.
In any case, I don't know which module to get. The JAD I used to deploy the cod was called green.jad
so I have no idea why myMidlet is important. I wouldn't see green.jad somewhere?
Anyway, I would appreciate any code that does this correctly.
Please see this thread on this issue.
-
VPN network for different countries
Hello everyone,
I would like to ask you about the Cenario below,
A company has the same Structure in different countries.
in a country, there are some offices, about 30-40 and a data center.
I thought to connect the offices with the domain controller in a country was to implement VPN Flex.How would be possible to interconnect all countries?
I found a few Graphis on a hierarchical network which is more or less on a connection between hubs and using the nodal point.Can someone give me more details about a recommendation? Perhaps a guide?
is it possible to use a VPN FLEX with Central HUB and connect all offices together for all offices for a company?Thank you very much
Thomas
Hi Thomas,
Normally, he would address the two tunnels:
Hub to hub and talking to talk.
In normal operation, rays have relationships with the two hubs. After a failure, the routing protocol passes one hub to another.
If we talked establishes one connection with the other speaks, a tunnel a spoke-to-spoke dynamic is created with the configuration of switching shortcut.
Hope it meets your request.
Kind regards
Aditya
Please evaluate the useful messages.
-
ASA L2L VPN UP with incoming traffic
Hello
I need help with this one, I have two identical VPN tunnel with two different customers who need access to one of our internal server, one of them (customer) works well, but the other (CustomerB) I can only see traffic from the remote peer (ok, RX but no TX). I put a sniffer on ports where the ASA and the server are connected and saw that traffic is to reach the server and traffic to reach the ASA of the server then nothing...
See the result of sh crypto ipsec his below and part of the config for both clients
------------------
address:
local peer 100.100.100.178
local network 10.10.10.0 / 24
local server they need access to the 10.10.10.10
Customer counterpart remote 200.200.200.200
Customer remote network 172.16.200.0 / 20
CustomerB peer remote 160.160.143.4
CustomerB remote network 10.15.160.0 / 21
---------------------------
Output of the command: "SH crypto ipsec its peer 160.160.143.4 det".
address of the peers: 160.160.143.4
Tag crypto map: outside_map, seq num: 3, local addr: 100.100.100.178outside_cryptomap list of allowed access host ip 10.10.10.10 10.15.160.0 255.255.248.0
local ident (addr, mask, prot, port): (10.10.10.10/255.255.255.255/0/0)
Remote ident (addr, mask, prot, port): (10.15.160.0/255.255.248.0/0/0)
current_peer: 160.160.143.4#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
#pkts decaps: 827, #pkts decrypt: 827, #pkts check: 827
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, comp #pkts failed: 0, #pkts Dang failed: 0
success #frag before: 0, failures before #frag: 0, #fragments created: 0
Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
#pkts not his (send): 0, invalid #pkts his (RRs): 0
#pkts program failed (send): 0, #pkts decaps failed (RRs): 0
#pkts invalid prot (RRs): 0, #pkts check failed: 0
invalid identity #pkts (RRs): 0, #pkts invalid len (RRs): 0
#pkts incorrect key (RRs): 0,
#pkts invalid ip version (RRs): 0,
replay reversal (send) #pkts: 0, #pkts replay reversal (RRs): 0
#pkts replay failed (RRs): 0
#pkts min frag mtu failed (send): bad frag offset 0, #pkts (RRs): 0
#pkts internal err (send): 0, #pkts internal err (RRs): 0local crypto endpt. : 100.100.100.178, remote Start crypto. : 160.160.143.4
Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
current outbound SPI: C2AC8AAESAS of the esp on arrival:
SPI: 0xD88DC8A9 (3633170601)
transform: esp-3des esp-md5-hmac no compression
running parameters = {L2L, Tunnel}
slot: 0, id_conn: 5517312, crypto-card: outside_map
calendar of his: service life remaining (KB/s) key: (4373959/20144)
Size IV: 8 bytes
support for replay detection: Y
Anti-replay bitmap:
0xFFFFFFFF to 0xFFFFFFFF
outgoing esp sas:
SPI: 0xC2AC8AAE (3266087598)
transform: esp-3des esp-md5-hmac no compression
running parameters = {L2L, Tunnel}
slot: 0, id_conn: 5517312, crypto-card: outside_map
calendar of his: service life remaining (KB/s) key: (4374000/20144)
Size IV: 8 bytes
support for replay detection: Y
Anti-replay bitmap:
0x00000000 0x00000001-The configuration framework
ASA Version 8.2 (1)
!
172.16.200.0 customer name
name 10.15.160.0 CustomerB
!
interface Ethernet0/0
nameif outside
security-level 0
IP 100.100.100.178 255.255.255.240
!
interface Ethernet0/1
nameif inside
security-level 100
10.10.10.0 IP address 255.255.255.0
!
outside_1_cryptomap list extended access allowed host ip 10.10.10.10 customer 255.255.240.0
inside_nat0_outbound_1 list extended access allowed host ip 10.10.10.10 customer 255.255.240.0
inside_nat0_outbound_1 list extended access allowed host ip 10.10.10.10 CustomerB 255.255.248.0
outside_cryptomap list extended access allowed host ip 10.10.10.10 CustomerB 255.255.248.0
NAT-control
Overall 101 (external) interface
NAT (inside) 0-list of access inside_nat0_outbound_1
NAT (inside) 101 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 100.100.100.177
Route inside 10.10.10.0 255.255.255.0 10.10.10.254 1
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 200.200.200.200
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
card crypto outside_map 3 match address outside_cryptomap
peer set card crypto outside_map 3 160.160.143.4
card crypto outside_map 3 game of transformation-ESP-3DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 20
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP ipsec-over-tcp port 10000
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec svc
internal customer group strategy
Customer group policy attributes
Protocol-tunnel-VPN IPSec svc
internal CustomerB group strategy
attributes of Group Policy CustomerB
Protocol-tunnel-VPN IPSec
tunnel-group 160.160.143.4 type ipsec-l2l
tunnel-group 160.160.143.4 General-attributes
Group Policy - by default-CustomerB
IPSec-attributes tunnel-group 160.160.143.4
pre-shared key xxx
tunnel-group 200.200.200.200 type ipsec-l2l
tunnel-group 200.200.200.200 General attributes
Customer by default-group-policy
IPSec-attributes tunnel-group 200.200.200.200
pre-shared key yyy
Thank you
A.
Hello
It seems that the ASA is not Encrypting traffic to the second peer (However there is no problem of routing).
I saw this 7.x code behaviors not on code 8.x
However you can do a test?
You can change the order of cryptographic cards?
card crypto outside_map 1 match address outside_cryptomap
peer set card crypto outside_map 1 160.160.143.4
map outside_map 1 set of transformation-ESP-3DES-MD5 crypto
card crypto outside_map 3 match address outside_1_cryptomap
card crypto outside_map 3 set pfs
peer set card crypto outside_map 3 200.200.200.200
card crypto outside_map 3 game of transformation-ESP-3DES-SHA
I just want to see if by setting the peer nonworking time to be the first, it works...
I know it should work the way you have it, I just want to see if this is the same behavior I've seen.
Thank you.
Federico.
-
ASA 5505: VPN access to different subnets
Hi All-
I'm trying to understand how to configure our ASA so that remote users can have VPN access to two different subnets (Office LAN and LAN phone). Currently I have 3 VLAN configuration - VLAN 1 (inside), VLAN 2 (outside), VLAN 13 (phone LAN). Essentially, remote users must be able to access their PC (192.168.1.0/24) and also have access to the office phone system (192.168.254.0/24). Is it still possible? Here are the configurations on our ASA,
Thanks in advance:
ASA Version 8.2 (5)
!
names of
name 10.0.1.0 Net-10
name 20.0.1.0 Net-20
name phone 192.168.254.0
name 192.168.254.250 PBX
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
switchport access vlan 3
!
interface Ethernet0/6
!
interface Ethernet0/7
switchport access vlan 13
!
interface Vlan1
nameif inside
security-level 100
192.168.1.98 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
address IP X.X.139.79 255.255.255.224
!
interface Vlan3
No nameif
security-level 50
192.168.5.1 IP address 255.255.255.0
!
interface Vlan13
nameif phones
security-level 100
192.168.254.200 IP address 255.255.255.0
!
passive FTP mode
object-group service RDP - tcp
EQ port 3389 object
object-group service DM_INLINE_SERVICE_1
the purpose of the ip service
EQ-ssh tcp service object
vpn_nat_inside of access list extensive ip Net-10 255.255.255.224 allow 192.168.1.0 255.255.255.0
access-list extended vpn_nat_inside allowed ip Net-10 255.255.255.224 phones 255.255.255.0
inside_nat0_outbound list extended access permits all ip Net-10 255.255.255.224
inside_access_in of access allowed any ip an extended list
Split_Tunnel_List list standard access allowed Net-10 255.255.255.224
phones_nat0_outbound list extended access permits all ip Net-10 255.255.255.224
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_1 Mac host everything
pager lines 24
Enable logging
timestamp of the record
record monitor errors
record of the mistakes of history
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 phones
mask IP local pool SSLClientPool-10 10.0.1.1 - 10.0.1.20 255.255.255.128
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global interface (10 Interior)
Global 1 interface (outside)
global interface (phones) 20
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (10 vpn_nat_inside list of outdoor outdoor access)
NAT (phones) 0-list of access phones_nat0_outbound
NAT (phones) 1 0.0.0.0 0.0.0.0
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 X.X.139.65 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication enable LOCAL console
the ssh LOCAL console AAA authentication
LOCAL AAA authorization command
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint ASDM_TrustPoint0
registration auto
name of the object CN = not - asa .null
pasvpnkey key pair
Configure CRL
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
lifetime 28800
VPN-sessiondb max-session-limit 10
Telnet timeout 5
SSH 192.168.1.100 255.255.255.255 inside
SSH 192.168.1.0 255.255.255.0 inside
SSH Mac 255.255.255.255 outside
SSH timeout 60
Console timeout 0
dhcpd auto_config inside
!
dhcpd address 192.168.1.222 - 192.168.1.223 inside
dhcpd dns 64.238.96.12 66.180.96.12 interface inside
!
a basic threat threat detection
host of statistical threat detection
Statistics-list of access threat detection
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
SSL-trust outside ASDM_TrustPoint0 point
WebVPN
allow outside
AnyConnect essentials
SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image
SVC disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2 image
enable SVC
tunnel-group-list activate
internal SSLClientPolicy group strategy
attributes of Group Policy SSLClientPolicy
WINS server no
value of 64.238.96.12 DNS server 66.180.96.12
VPN-access-hour no
VPN - connections 3
VPN-idle-timeout no
VPN-session-timeout no
IPv6-vpn-filter no
VPN-tunnel-Protocol svc
group-lock value NO-SSL-VPN
by default no
VLAN no
NAC settings no
WebVPN
SVC mtu 1200
SVC keepalive 60
client of dpd-interval SVC no
dpd-interval SVC bridge no
SVC compression no
attributes of Group Policy DfltGrpPolicy
value of 64.238.96.12 DNS server 66.180.96.12
Protocol-tunnel-VPN IPSec svc webvpn
attributes global-tunnel-group DefaultRAGroup
address-pool SSLClientPool-10
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared key *.
NO-SSL-VPN Tunnel-group type remote access
General-attributes of the NO-SSL-VPN Tunnel-group
address-pool SSLClientPool-10
Group Policy - by default-SSLClientPolicy
NO-SSL-VPN Tunnel - webvpn-attributes group
enable PAS_VPN group-alias
allow group-url https://X.X.139.79/PAS_VPN
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
privilege level 3 mode exec cmd command perfmon
privilege level 3 mode exec cmd ping command
mode privileged exec command cmd level 3
logging of the privilege level 3 mode exec cmd commands
privilege level 3 exec command failover mode cmd
privilege level 3 mode exec command packet cmd - draw
privilege show import at the level 5 exec mode command
privilege level 5 see fashion exec running-config command
order of privilege show level 3 exec mode reload
privilege level 3 exec mode control fashion show
privilege see the level 3 exec firewall command mode
privilege see the level 3 exec mode command ASP.
processor mode privileged exec command to see the level 3
privilege command shell see the level 3 exec mode
privilege show level 3 exec command clock mode
privilege exec mode level 3 dns-hosts command show
privilege see the level 3 exec command access-list mode
logging of orders privilege see the level 3 exec mode
privilege, level 3 see the exec command mode vlan
privilege show level 3 exec command ip mode
privilege, level 3 see fashion exec command ipv6
privilege, level 3 see the exec command failover mode
privilege, level 3 see fashion exec command asdm
exec mode privilege see the level 3 command arp
command routing privilege see the level 3 exec mode
privilege, level 3 see fashion exec command ospf
privilege, level 3 see the exec command in aaa-server mode
AAA mode privileged exec command to see the level 3
privilege, level 3 see fashion exec command eigrp
privilege see the level 3 exec mode command crypto
privilege, level 3 see fashion exec command vpn-sessiondb
privilege level 3 exec mode command ssh show
privilege, level 3 see fashion exec command dhcpd
privilege, level 3 see the vpnclient command exec mode
privilege, level 3 see fashion exec command vpn
privilege level see the 3 blocks from exec mode command
privilege, level 3 see fashion exec command wccp
privilege see the level 3 exec command mode dynamic filters
privilege, level 3 see the exec command in webvpn mode
privilege control module see the level 3 exec mode
privilege, level 3 see fashion exec command uauth
privilege see the level 3 exec command compression mode
level 3 for the show privilege mode configure the command interface
level 3 for the show privilege mode set clock command
level 3 for the show privilege mode configure the access-list command
level 3 for the show privilege mode set up the registration of the order
level 3 for the show privilege mode configure ip command
level 3 for the show privilege mode configure command failover
level 5 mode see the privilege set up command asdm
level 3 for the show privilege mode configure arp command
level 3 for the show privilege mode configure the command routing
level 3 for the show privilege mode configure aaa-order server
level mode 3 privilege see the command configure aaa
level 3 for the show privilege mode configure command crypto
level 3 for the show privilege mode configure ssh command
level 3 for the show privilege mode configure command dhcpd
level 5 mode see the privilege set privilege to command
privilege level clear 3 mode exec command dns host
logging of the privilege clear level 3 exec mode commands
clear level 3 arp command mode privileged exec
AAA-server of privilege clear level 3 exec mode command
privilege clear level 3 exec mode command crypto
privilege clear level 3 exec command mode dynamic filters
level 3 for the privilege cmd mode configure command failover
clear level 3 privilege mode set the logging of command
privilege mode clear level 3 Configure arp command
clear level 3 privilege mode configure command crypto
clear level 3 privilege mode configure aaa-order server
context of prompt hostname
no remote anonymous reporting call
Hello
Loss of connectivity to the LAN is not really supposed all remove this command UNLESS your network is using another device as their gateway to the Internet. In this case configuration dynamic PAT or political dynamics PAT (as you) would make sense because the LAN hosts would see your VPN connection from the same directly connected network users and would be know to traffic before the ASA rather than their default gateway.
So is this just for VPN usage and NOT the gateway on the LAN?
If it is just the VPN device I'd adding this
global interface (phones) 10
He would do the same translation for 'phones' as he does on 'inside' (of course with different PAT IP)
-Jouni
-
"One-click" How do I export an image to a set of files with different resolutions .png?
Hello
How far is 'one-click' export an image to a set of files with different resolutions .png? (I need for a set of iOS app icons).
For example: export a file MyAppIcon.psd in the following:
MyAppIcon_29x29.png
MyAppIcon_57x57.png
MyAppIcon_114x114.png
MyAppIcon_512x512.png
MyAppIcon_48x48.png
MyAppIcon_72x72.png
I almost managed to do with the Actions of Photoshop, but does not know how the names of files to include the name of the original image file. In other words, the NewApp.psd file should export to NewApp_29x29.png, not MyAppIcon_29x29.png.
Thank you!
No problem, please try this...
#target photoshop app.bringToFront(); main(); function main(){ if(!documents.length) return; var Name = app.activeDocument.name.replace(/\.[^\.]+$/, ''); try{ var Path = activeDocument.path; }catch(e){ alert("Please save this file then re-run the script!"); return; } var strtRulerUnits = app.preferences.rulerUnits; var strtTypeUnits = app.preferences.typeUnits; app.preferences.rulerUnits = Units.PIXELS; snapShot(); var saveFile = File(Path + "/" + Name + "_512x512.png"); activeDocument.resizeImage(512, 512, undefined, ResampleMethod.BICUBICSHARPER); SavePNG(saveFile); revertToLastSnapshot(); var saveFile = File(Path + "/" + Name + "_114x114.png"); activeDocument.resizeImage(114, 114, undefined, ResampleMethod.BICUBICSHARPER); SavePNG(saveFile); revertToLastSnapshot(); var saveFile = File(Path + "/" + Name + "_72x72.png"); activeDocument.resizeImage(72, 72, undefined, ResampleMethod.BICUBICSHARPER); SavePNG(saveFile); revertToLastSnapshot(); var saveFile = File(Path + "/" + Name + "_57x57.png"); activeDocument.resizeImage(57, 57, undefined, ResampleMethod.BICUBICSHARPER); SavePNG(saveFile); revertToLastSnapshot(); var saveFile = File(Path + "/" + Name + "_48x48.png"); activeDocument.resizeImage(48, 48, undefined, ResampleMethod.BICUBICSHARPER); SavePNG(saveFile); revertToLastSnapshot(); var saveFile = File(Path + "/" + Name + "_29x29.png"); activeDocument.resizeImage(29,29, undefined, ResampleMethod.BICUBICSHARPER); SavePNG(saveFile); app.preferences.rulerUnits = strtRulerUnits; app.activeDocument.close(SaveOptions.DONOTSAVECHANGES); } function SavePNG(saveFile){ var pngOpts = new ExportOptionsSaveForWeb; pngOpts.format = SaveDocumentType.PNG; pngOpts.PNG8 = false; pngOpts.transparency = true; pngOpts.interlaced = false; pngOpts.quality = 100; activeDocument.exportDocument(new File(saveFile),ExportType.SAVEFORWEB,pngOpts); } function snapShot() { var desc9 = new ActionDescriptor(); var ref5 = new ActionReference(); ref5.putClass( charIDToTypeID('SnpS') ); desc9.putReference( charIDToTypeID('null'), ref5 ); var ref6 = new ActionReference(); ref6.putProperty( charIDToTypeID('HstS'), charIDToTypeID('CrnH') ); desc9.putReference( charIDToTypeID('From'), ref6 ); desc9.putEnumerated( charIDToTypeID('Usng'), charIDToTypeID('HstS'), charIDToTypeID('FllD') ); executeAction( charIDToTypeID('Mk '), desc9, DialogModes.NO ); }; function revertToLastSnapshot() { var doc = app.activeDocument; var hsObj = doc.historyStates; var hsLength = hsObj.length; for (var i=hsLength - 1;i>-1;i--) { if (hsObj[i].snapshot) { doc.activeHistoryState = doc.historyStates.getByName('Snapshot ' + i); break; } } };
-
Click on the boxes with different audio
Hello!
I use 5 Cp and I have problems with the audio. Button or box where to click must play an audio short or long after that is clicked on. In the text, I want to cover some words with boxes click with different sounds, students can click to hear the sounds. in the text, there may be a lot of words I want to cover with boxes to click. Is it possible to do? If Yes please let me know how.
Thank you
Ok. Who can be a little trickier. Normally a button or click box has a break point on the timeline and once you click on the object continues to play beyond its break point. This means that you get only a click... UNLESS... you change the Action when a click to be an advance Action that does two things. First of all, it does everything you want to take place (for example to read the audio file) and THEN he moves the read head to a point BEFORE the break point so that you get another possibility to click New.
Blog of Lilybiri has some good examples of this sort of thing: http://lilybiri.posterous.com/
You may encounter a problem where even after you have everything installed correctly the buttons stop working after a while. In this case your best recourse would be to use the Widgets event handler instead, these can transform any object into a clickable button screen. But even better, is that they give you preferences to disable continue and the pass/fail criteria reset after Action so that your users can click on your buttons as often they like to repeat actions, these useful widgets trial versions can be downloaded here.
-
Yosemite: Why 'Shares and Permissions' displays 2 all users with different privileges?
Some folders and files inside my user folder sharing and permissions like this:
I can remove the user from "search...". "(a user who has been deleted and no longer exists) but I don't know what to do on both"all"users with different permissions. I can't delete the one with custom privileges. Help!
Solved by Leroy Douglas. See What are these custom privileges?
-
Photos with different apple id: s
Any way to sort photos taken with various apple id: s in photos for mac? I have three different iPhones that has been moved from parents to children. Is there anyway to sort images with different apple id: s? I heard that there is way to sort different (smart folder) with the model of phone, but this is not enough cause phones were used earlier by the parents. And I want to use only a single library of pictures, so the different IDs: s for mac is not the solution. It would be nice to get this functionality.
You can use smart albums with a combination of constraints: the model of the iPhone and the date rank when the iPhone has been used by a person in particular. If the iPhone has been in use you make in the years 2012 and 2013 creates a smart album that will check for the ipHone and the date range. Then announces a keyword "Photo by Me" of all the photos in this album. Do the same for the other ranges of iPhones and date and assign the photographer as a key word.
If you keep marking new imports with a keyword of photographer then you can create smart albums for every photographer.
-
Why you do not have your products with different colors? compatible with the colors of the iPhone or the iPad? Example: Gold Earpods, silver, BLACK and Rose Gold.
You say Apple your wishes on the link below.
Maybe you are looking for
-
Hello I have a g-20 and on the back of it there is a S-video port. As far as I know I owe then power save my camcorder vhs movies. Using Intervideo windvd is however nothing. With the help of pinaclle studio 9 recognizes a tv but stll port no images
-
2 UPDATES have consistently failed to install since 12/16/10: update of security for Microsoft Works 9 (KB2431831) and update of security for Microsoft Office System 2007 (KB2288931). I tried to REINSTALL... and CONTINUED on for more than a week now
-
HP Pavilion g6-2240ea Notebook: plugged in, not charging to help!
Hello! I bought my HP Pavilion 2240ea g5 in April 2013. Everything worked smoothly, until I started noticing, he had stopped charging. It works very well with the adapter plugged in, but it will not load. Initially, he read (95% charged, plugged in,
-
It happened over and over again. Please help me, thanks.
-
Can I change my subscription information?
When I signed up for the subscription of cloud I register as myself and not my employer/company, because I'd be the only one to use it.Now, I think it was a mistake. Is it possible to change this? Who should I contact?It must be in the name of my com