VPN client and Setup for the RV042

Similar Questions

• VPN client and ssh to the external interface of the ASA

  Hello world

  I was testing clientless ssl in my lab at home.

  When you're connected via vpn without customer, I am able to ssh ASA outside interface, but when I use ssl vpn only I can't ssh to the external interface of the ASA.

  Need to figure out how I can ssh to the external interface of the ASA using clientless ssl vpn?

  Concerning

  MAhesh

  Mahesh,

  When you are on clientless SSL VPN to your customer is not limited routes of the Internet, isn't being NATted etc. If ASA is set to allow ssh from outside, then the VPN SSL without client user is no different from any other.

  A the user SSL VPN full tunnel can have any or all of these factors at play. One of them can cause the impossibility to access the ASA outside interface via ssh. I see the configuration to tell you which one (or more) is to blame.

• Configure the Cisco VPN client to pass through the VPN site-to-site (GUI)

  Hello

  I say hat the chain and responses I've seen to achieve this goal have been great...

  https://supportforums.Cisco.com/discussion/12234631/Cisco-ASA-5505-VPN-p...

  and

  https://supportforums.Cisco.com/document/12191196/AnyConnect-client-site...

  My question is "we will get this configuration by using the graphical user interface for someone who is not notified about the command line?"

  Thank you

  Of course, all this can be configured via ASDM.

  Looking at the second example you posted above, they point you first change:

  ACL split of the tunnel for the AnyConnect customer

  This Configuration > remote access VPN > network (Client) access > AnyConnect connection profile > (chose the profile and select Edit) > (choose "Manage" next to group policy) > Edit > advanced > Split Tunneling > ensure that the policy does not "Inherit" but rather "Tunnel network list below" > Unselect "Inherit" next to the network list, then 'manage '. Enter your networks you want in the GUI in this dialog box. Click OK all the way back to the main window ASDM and click on apply.

  You then change:

  Crypto ACL for the tunnel from Site to Site

  To do this, go to Configuration > VPN Site-to_site > connection profiles > (choose your profile and select edit) > add the VPN client address pool to the list of local network between protect networks. Yet once, click OK all the way back to the main window ASDM and click on apply.

  Then, allow the

  ASA to redirect back on the same interface traffic it receives

  .. is defined under Configuration > Device Setup > Interfaces. (check the box at the bottom of this screen). Click on apply

  Finally, there is the NAT exemption. For which go to Configuration > firewall > rules NAT. Add a NAT device rule before rules network object with Interface Source out, Source address your address pool VPN, the Destination address to include remote subnets and Action is Static Source NAT type source address and destination address remaining as original (i.e. without NAT). Once on OK all the way back to the main window ASDM and click on apply. Save and test.

  Good luck. Don't forget to note the brand and posts useful when your question is answered.

• A VPN client / ASA cannot access the Internet.

  VPN clients can get to the servers internal/DMZ but not Internet. This is the partial config of the SAA. TIA

  Pool VPN 10.17.70.0

  DMZ 192.168.100.0

  172.0.0.0 internal

  -------------------------------------

  nonatdmz list of allowed ip extended access any 192.168.100.0 255.255.255.0

  access extensive list ip 172.0.0.0 nonatdmz allow 255.0.0.0 10.17.70.0 255.255.255.0

  standard access list splittunnel allow 172.0.0.0 255.0.0.0

  Global interface (10 outside)

  Global interface (Businesspartner) 10

  NAT (inside) 0-list of access nonatdmz

  NAT (Inside) 10 0.0.0.0 0.0.0.0

  NAT (DMZ) 10 0.0.0.0 0.0.0.0

  Vinnie, happy that you have found here.

  Telnet for asa by vpn session, you need to add this statement.

  management-access inside

  In this same connection see split tunnel vs local Allow only lan access, you can learn the differences and you will better understand your configuration asa related to ra vpn.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080702999.shtml

• Cisco VPN Client and Windows XP VPN Client IPSec to ASA

  I configured ASA for IPSec VPN via Cisco VPN Client and XP VPN client communications. I can connect successfully with Cisco VPN Client, but I get an error when connecting with the XP client. Debugging said "misconfigured groups and transport/tunneling mode" I know, they use different methods of transport and tunneling, and I think that I have configured both. Take a look at the config.

  PS a funny thing - when I connect with client VPN in Windows Server 2003, I have no error. The only difference is that client XP is behind an ADSL router and client server is directly connected to the Internet on one of its public IP of interfaces. NAT in the case of XP can cause problems?

  Config is:

  !

  interface GigabitEthernet0/2.30

  Description remote access

  VLAN 30

  nameif remote access

  security-level 0

  IP 85.*. *. 1 255.255.255.0

  !

  access-list 110 scope ip allow a whole

  NAT list extended access permit tcp any host 10.254.17.10 eq ssh

  NAT list extended access permit tcp any host 10.254.17.26 eq ssh

  access-list extended ip allowed any one sheep

  access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh

  sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0

  tunnel of splitting allowed access list standard 192.168.121.0 255.255.255.0

  flow-export destination inside-Bct 192.168.1.27 9996

  IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0

  ARP timeout 14400

  global (outside-Baku) 1 interface

  global (outside-Ganja) interface 2

  NAT (inside-Bct) 0 access-list sheep-vpn

  NAT (inside-Bct) 1 access list nat

  NAT (inside-Bct) 2-nat-ganja access list

  Access-group rdp on interface outside-Ganja

  !

  Access remote 0.0.0.0 0.0.0.0 85.*. *. 1 2

  Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1

  Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1

  Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1

  Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1

  Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1

  Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1

  Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1

  Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1

  dynamic-access-policy-registration DfltAccessPolicy

  Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT

  Crypto ipsec transform-set newset aes - esp esp-md5-hmac

  Crypto ipsec transform-set esp-3des esp-md5-hmac vpnclienttrans

  Crypto ipsec transform-set vpnclienttrans transport mode

  Crypto ipsec transform-set esp-3des esp-md5-hmac raccess

  life crypto ipsec security association seconds 214748364

  Crypto ipsec kilobytes of life security-association 214748364

  raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

  vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1

  card crypto interface for remote access vpnclientmap

  crypto isakmp identity address

  ISAKMP crypto enable vpntest

  ISAKMP crypto enable outside-Baku

  ISAKMP crypto enable outside-Ganja

  crypto ISAKMP enable remote access

  ISAKMP crypto enable Interior-Bct

  crypto ISAKMP policy 30

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  No encryption isakmp nat-traversal

  No vpn-addr-assign aaa

  Telnet timeout 5

  SSH 192.168.1.0 255.255.255.192 outside Baku

  SSH 10.254.17.26 255.255.255.255 outside Baku

  SSH 10.254.17.18 255.255.255.255 outside Baku

  SSH 10.254.17.10 255.255.255.255 outside Baku

  SSH 10.254.17.26 255.255.255.255 outside-Ganja

  SSH 10.254.17.18 255.255.255.255 outside-Ganja

  SSH 10.254.17.10 255.255.255.255 outside-Ganja

  SSH 192.168.1.0 255.255.255.192 Interior-Bct

  internal vpn group policy

  attributes of vpn group policy

  value of DNS-server 192.168.1.3

  Protocol-tunnel-VPN IPSec l2tp ipsec

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value split tunnel

  BCT.AZ value by default-field

  attributes global-tunnel-group DefaultRAGroup

  raccess address pool

  Group-RADIUS authentication server

  Group Policy - by default-vpn

  IPSec-attributes tunnel-group DefaultRAGroup

  pre-shared-key *.

  Hello

  For the Cisco VPN client, you would need a tunnel-group name configured on the ASA with a pre-shared key.

  Please see configuration below:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  or

  http://tinyurl.com/5t67hd

  Please see the section of tunnel-group config of the SAA.

  There is a tunnel-group called "rtptacvpn" and a pre-shared key associated with it. This group name is used by the VPN Client Group name.

  So, you would need a specific tunnel-group name configured with a pre-shared key and use it on the Cisco VPN Client.

  Secondly, because you are behind a router ADSL, I'm sure that's configured for NAT. can you please activate NAT - T on your ASA.

  "crypto isakmp nat-traversal.

  Thirdly, change the transformation of the value

  raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

  Let me know the result.

  Thank you

  Gilbert

• VPN client and contradictory static NAT entries

  Hello, we have a VPN IPSEC implemented on a router for remote access. It works very well, for the most part. We have also a few PAT static entries to allow access to a web server, etc. from the outside. We deny NATting from the range of IP addresses for the range of VPN client and it works except for entries that also have PAT configurations.

  So, for example, we have web server 10.0.0.1 and a PAT redirection port 10.0.0.1: 80 to the IP WAN port 80. If a VPN client tries to connect to 10.0.0.1: 80, the syn - ack packet back to the customer WAN IP VPN on the router! If the VPN client connects to the RDP server 10.0.0.2:3389, it works very well that this server is not a static entry PAT.

  Is there a way to get around this?

  Thank you!

  There is a way to get around, use the same settings you have for your dynamic nat in your nat staitc entries, something like this:

  Currently, it should show as:

  IP nat inside source static XXXXX XXXX 80 80

  you need to take it

  IP nat inside source static 80 XXXX XXXX 80 map route AAAA

  When your itinerary map YYY refers to something with an acl that you refuse traffic from inside your router for the pool of vpn

  IP Access-list ext nonat

  deny ip 10.0.0.0 0.0.0.255

  Licensing ip 10.0.0.0 0.0.0.255 any

  route allowed AAAA 10 map

  match ip address sheep

  You even need all the static PAT

  HTH

  Ivan

• How can I set the default font size and type for the outgoing Hotmail mail?

  How can I set the default font size and type for the outgoing Hotmail mail?

  Hi Dale,

  What is the email client do you use?

  Outlook can be configured per - start Outlook-> Tools-> Options-> mail-> fixed Format and fonts... Select the font and size you need... Click ok on all screens.

  I hope this helps.

• VPN client and redundant peering

  Hello world

  PC user's config with remote access VPN client.

  Tell the client pc has the configuration of the VPN client with backup servers and if ASA primary is the stop will be the secondary question of the new IP address of the client VPN gateway

  address automatically?

  Here the SAA is not in any failover mode.

  Concerning

  The list of backup server is used when establishing a new VPN connection.  If it the customer has an active connection and the VPN server is no longer available then the user will have to re-establish the connection manually.

  --

  Please do not forget to rate and choose a good answer

• Adobe CC will not update my Photoshop and Lightroom for the new 2015 CC, it fails at 43% every time and gives an error code of 50

  Adobe CC will not update my Photoshop and Lightroom for the new 2015 CC, it fails at 43% every time and gives an error code 50.

  Hi Gregory,

  Please refer to the threads below to resolve the error code 50:

  Which is updated CC 50 error Code?

  Setup error - code error 50 creative cloud.

  You can also try to download the app from the link below:

  Direct download links of Adobe CC 2015: 2015 creative cloud release | ProDesignTools

  * Be sure to read the important Instructions before downloading *.

  Kind regards

  Sheena

• Urgent - Custom authentication and authorization for the application of the ADF

  Hi friends,
  
  Custom implementation for authentication and authorization for the application of the ADF
  
  My project to use the OID , authentication and authorization, we will need to support both OAM and DB tables ( according to the preferences of the client during the installation ).
  
  I am new to this and do not have a clue about the same.
  
  Please guide me how to set up both in JDeveloper 11 g + ADF
  
  Thanks in advance.

  The answers you got up to present every point in the right direction. ADF security see the authentication of WLS, even for business authorization with respect to user roles defined on the WLS server. During the deployment, ADF security defined application roles are mapped to the user enterprise groups

  Application developed using Jdeveloper ADF +.

  This would use WLS for authentication

  Users of authentication - LDAP (OID) - are stored in LDAP

  Use the OID authentication provider in WLS

  Authorization - OAM or database (authorization details are stored in the DB or OAM tables)

  You can't allow users without authentication. If you need create authentication providers additional if they exist for OAM and RDBMS (there is a supplier of existing RDBMA, that you can use to identify users and to assign membership user groups). Then, you set the optional flag so that when authentication fails for additional providers you can always start the application.

  When running Admin users - create users from roles to create and assign permission privileges to the role (for pages and workflows)
  assign (or remove) the roles to/to leave users.

  ADF security uses JAAS to permissions that you can change using Enterprise Manager when running. Permissions are granted to the application roles and application roles are granted to business roles that which then has users become members of the. If you want to change the status of user account, then you don't do this the ADF or EM, but use a direct access to the provider of the user (for example, access OID, RDBMS access etc.) There is no unified administration API available that would allow you to do this via WLS (which uses OPSS).

  If your question is in the context of the ADF, the documentation, with that you should follow is OPSS and WLS authentication providers.

  Frank

• In the middle of my teens adding devices, and registration for the apple's music, security issues have been changed and now nobody seems to remember the answers.  How can you bypass those to change your settings?

  In the middle of my teens adding devices, and registration for the apple's music, security issues have been changed and now nobody seems to remember the answers.  How can you bypass those to change your settings?

  You must ask security team account Apple to reset your security questions. To contact them, click here and choose a method; If this page does not list one for your country or if you are unable to call, complete and submit this form.

  
  (140233)

• Is there a way to copy the drivers and setup of the drive from the computer and transfer them to the reader of the dead computer?

  Separated from this thread.

  Is there a way to copy the drivers and setup of the drive from the computer and transfer them to the reader of the dead computer?

  Hello

  You cannot copy the drivers installed anyway.

  Saving your files:

  You can remove the hard drive and put it in a hard drive USB enclosure > plug it into another computer > and try to read and copy your data in this way.

  See you soon.

• How can I fix lines horizontal randomly and glitter for the LCD screens for HP Pavilion dv5 Vista?

  How can I correct random lines horizontal and glitter for the LCD screens for windows vista HP Pavilion dv5? Only, it happens randomly and can get all a few minutes at a time every few hours. The entire screen white and black and horizontal lines will appear during the flickering on the half top of the screen only. Nothing else changes. My sound is immutable, and none of my screens change the size or location. However, they may appear up and down during the flashing. Can someone give me an idea of what is wrong? I looked on Google for possible corrections, but most of them seem to be for refresh rate and I don't have a notch for this and can't change it according to the steps they offer.

  Read my initial response on what it takes to please.

  "See if this helps you:

  These lines indicate corruption graphics driver or lack of graphic material.

  Go to the HP Web site > Search a drivers and download article > search your laptop model number > your operating system > drivers for it: either video / graphic / Chipset (according to the wording it) > download and install the drivers.

  http://WWW8.HP.com/us/en/support-drivers.html

  If that fixed it, it seems to me be a problem of graphic material.

  Because it's a laptop; If under warranty, contact HP.

  If is not under warranty, contact a repair shop, local. »

  See you soon.

• Where can I find the drivers and software for the LaserJet Pro M1132 MFP on Mac OS Mountain Lion?

  Hello

  According to http://support.hp.com/us-en/document/c01664444 it doesn't seem to be a software and drivers for the LaserJet Pro M1132 MFP.

  When will they be available?

  I read in http://support.hp.com/us-en/document/c03427752 that "today, a solution for your printer is not available for the Mountain Lion. However, an update of the driver will be available in fall 2012 . "Since it's already winter 2012, a solution will be available before January 2013?

  Thank you.

  Hi Chun Pong,

  Seems to download the software I mentioned before has been deleted. This means that a new driver will be downloaded.

  Please visit the site from time to time if a new software is available. I'll keep an eye as well and provide an update here, if the new software can be downloaded. It may take a few days.

• Where to put the report server ip and port for the Siebel server?

  Hello

  Where to put the report server ip and port for the Siebel server? I have checked the document "Reports Siebel Guide" but does not know where is the configuration section ' ip address of the server and port ' for 'Oracle BI Publisher.

  Note: I have installed BI Publisher, now necessary to define the ip editor and siebel server port.

  Please help, thanks.

  Hello

  Communication between Siebel and BEEP coming through webservices. You must set the Siebel Outboundwebservice 'PublicReportService' address to address BI Publisher.

  Similarly, the address of the webservice Siebel Inbound 'BIPSiebelSecurityWS' will be used by BEEP setting under the security model of Siebel - Siebel end Webservice poin of connecting to Siebel EAI, data inorder of success authenticate the Siebel user to perform the tasks of report being initiate Siebel UI.

  Please go through the integration document attached to the thread "Re: ADVISE WEBCAST: BI Publisher 11g Configuration with Siebel", it is any integration Siebel with BEEP 11g steps. " But if you go through each step, there are details about why we do it. Through this way you can better understand the integration.

  I hope this helps.

  Thank you
  Maria