VPN Client problem

Similar Questions

• Windows 7 64 bit VPN client problems

  Hello

  I am running Windows 7 Professional 64 bit and Cisco VPN client 5.0.07.0240. I am able to connect to my corporate network and work ok but connection is very slow!

  Connection time is distributed as follows:

  Client program VPN Opening: 70 seconds.

  Click on connect and wait for the user credentials dialog box: 30 seconds.

  Enter the credentials, and then click ok then 'user authentication': 90 seconds.

  "Negotiate security policies": 60 seconds.

  User area credentials if poster again, re - enter the credentials that the dialog box is empty, and then click ok: 90 seconds.

  "User authentication", then connection established: 120 seconds.

  I have a colleague running 64-bit Windows 7 (ultimate edition) which uses the same version and does not have these problems.

  Any ideas anyone?

  See you soon,.

  Gary

  Gary, thanks for the update. If disabling the firewall and restart vpn service did not help. Could you please try and install the 5.0.07.0290 version?

  Before do you, I would like to know if you import .pcf for the VPN Client files. If so, please try to re-create a file .pcf on the PC and try and use this file to connect. Also, I see that the existing .pcf file you are using is a file read-only. Could you change this and give permissions to write to the file, and try to connect. If th does not help the two steps will then install the 5.0.07.0290 version.

  Thank you

  Delvallée

• VPN client problem long transfer of files with VPN3000

  I have problems transferring big files (more than 4 MB) using customer vpn 4.8.02 or 5.0 with vpn3020 4.7.2.N

  It happens the question with MTU. Try reducing the MTU value by running the file setMTU.exe on the VPN client. Make sure you do not fragment bit is not set on the intermediate routers. For setting MTU on VPN 3000 refer URL http://www.cisco.com/en/US/products/hw/vpndevc/ps2284/products_configuration_guide_book09186a00800d81b3.html

• VPN access with VPN client problem. Help, please

  I have a PIX 520 as VPN tunnels endpoint device. I was able to establish an IPsec connection. I checked that I have gave me an address in the IP pool that I set up but I can't to any resource on the internal network. I could only ping myself. When I run ' ipconfig/all' I see my address on the correct vpn with DNS interface, but my front door is set to my own address. I think that's the problem. Please help me solve this problem. Let me know if you need more information.

  Here are some suggestions you might try to get this working:

  1.) change your "taken" to access-list. The lines are no longer supported by Cisco even if they still work. This will help you in debugging your access list because there will be some hitcounts.

  There is a tool from cisco for conduits of concert on access lists:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/PIX?sort=release

  Download the: occ - 121.zip

  PIX Firewall Outbound leads binary converter for Windows, version 1.2.1

  2.) change your pool of VPN.

  IP local pool techvpn 10.x.x.100 - 10.x.x.120

  With this, it's already you have a 10.x.x.x subnet in your internal network. The ip pool automatically assigns a 255.0.0.0 for the VPN Clients subnet mask. This may cause routing problems. You can use a subnet used anywhere 172.16.100.x.

  example:

  No vpngroup address techvpn pool lsdvpn

  no ip local pool techvpn

  IP local pool techvpn 172.16.100.1 - 172.16.100.254

  vpngroup address techvpn pool lsdvpn

  No inside_outbound_nat0_acl access list

  No outside_cryptomap_dyn_20 access list

  inside_outbound_nat0_acl ip access list allow any 172.16.100.0 255.255.255.0

  outside_cryptomap_dyn_20 ip access list allow any 172.16.100.0 255.255.255.0

  Claire ipsec his

  Claire isakmp his

  sincerely

  Patrick

• BSOD with VPN Client problem

  I use the VPN Client 5.0.06.0110 to connect to my computer at home at my desk, which has an ASA5505.  If my immediate network to the client PC connection is lost while the VPN is active, I get a BSOD.  There is no problem if my grave DSL or a cable beyond my router is disconnected.  He only (and always) will fail if the network cable to the computer running the VPN Client is cut (or if my router loses power), while the link is connected.

  I am running:

  Windows 7 (all updates installed)

  Pentium Core 2

  4 GB of ram

  Atheros L1 Gigabit 10/100/1000 controller

  Any suggestion would be appreciated.

  BTW, here is the description for your reference:

  PC restarts if physical link is disrupted when a VPN connection

  Symptom: Restart the computer (the user can also see a Blue Screen Of Death (BSOD) before the reboot, based on the setup of the PC) if the physical link is disrupted when a VPN connection (that is when you see the error message "a network cable is unplugged).  This can occur if you run "shutdown" on your PC is connected to the way of the switch, turn off the SOHO router (or switch) the PC is connected to, lose your WiFi connection, or even disconnect the LAN cable to your wired Ethernet port. Conditions: Loss of physical connection during a VPN connection.

• % 305013-5-ASA: rules asymmetrical NAT matched for flows forward and backward; Connection refused because of the failure of the path opposite. NAT VPN clients problems after that put 8.3.2 to level.

  I've recently updated to 8.3.2 and I have been informed of these NAT changes, but even after reading the https://supportforums.cisco.com/docs/DOC-12569 I am still unable to rectify the communication network 192.168.100.0 VPN with hosts on 172.16.1.0 and 172.16.9.0. VPN clients connect to the external interface, and I try to ping inside and the demilitarized zone, respectable 172.16.1.0 and 172.16.9.0 hosts. VPN client shows that the two previously mentioned networks such as roads of security, but still not to the ping pong.

  # sh nat

  Manual NAT policies (Section 1)

  1 (inside) to the (whole) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  2 (inside) to the (whole) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  3 (inside) to the (whole) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - 172.16.12.0 obj - one-way 172.16.12.0

  translate_hits = 0, untranslate_hits = 0

  4 (dmz) to (outside) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  5 (dmz) to (outside) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - 172.16.12.0 obj - one-way 172.16.12.0

  translate_hits = 0, untranslate_hits = 0

  Auto NAT policies (Section 2)

  1 (dmz), to the source (external) static obj - 172.16.9.5 interface tcp www www service

  translate_hits = 0, untranslate_hits = 142

  2 (dmz) (outdoor) source static obj - 172.16.9.5 - 01 interface service tcp 3389 3389

  translate_hits = 0, untranslate_hits = 2

  3 (dmz) (outdoor) source static obj - 172.16.9.5 - 02 interface tcp ldap ldap service

  translate_hits = 0, untranslate_hits = 0

  4 (dmz) (outdoor) source static obj interface - 172.16.9.5 - 03 service ftp ftp tcp

  translate_hits = 0, untranslate_hits = 0

  5 (dmz) to (outside) of the source static obj - 172.16.9.5 - 04 interface tcp smtp smtp service

  translate_hits = 0, untranslate_hits = 267

  6 (inside) source static obj - 172.16.9.0 172.16.9.0 (dmz)

  translate_hits = 4070, untranslate_hits = 224

  7 (inside) to (dmz) source static obj - 10.1.0.0 10.1.0.0

  translate_hits = 0, untranslate_hits = 0

  8 (inside) to (dmz) source static obj - 172.16.0.0 172.16.0.0

  translate_hits = 152, untranslate_hits = 4082

  9 (dmz) to dynamic interface of the obj - 172.16.9.0 - 01 source (outdoor)

  translate_hits = 69, untranslate_hits = 0

  10 (inside) to the obj_any interface dynamic source (external)

  translate_hits = 196, untranslate_hits = 32

  I think you must following two NAT config

  NAT (inside, outside) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - 192.168.100.0 obj - 192.168.100.0
  NAT (dmz, external) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - 192.168.100.0 obj - 192.168.100.0

  Please configure them and remove any additional NAT configuration and then try again.

• Cisco 2621 to VPN client problem

  If I ping on the client to the network (behind the router), debug displays the client encryption and decryption of the router. The ping will not, because the router is not encrypt and so the customer is not getting anything to decrypt.

  The Setup is a bit different because the default route is within the network, as it is not the regular internet gateway. I have to add routes for pointing the customer who logs on the internet. Also, one machine uses this as a gateway (using a routemap). To troubleshoot, I removed the routemap custom without result. I think to change the default route, but I don't see how this would have on it.

  Any ideas? Am I missing something?

  Cisco 2621 12.2 (15) T running to the latest version of the client.

  username password XXX 7 XXXXXX

  AAA new-model

  !

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  AAA - the id of the joint session

  IP subnet zero

  !

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  Configuration group customer crypto isakmp XXXX

  key XXXXX

  pool ippool

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  !

  interface Loopback1

  192.168.254.1 IP address 255.255.255.0

  !

  interface FastEthernet0/0

  IP address 200.x.x.x 255.255.x.x

  no ip proxy-arp

  NAT outside IP

  automatic duplex

  automatic speed

  clientmap card crypto

  !

  interface FastEthernet0/1

  the IP 10.0.0.1 255.255.255.0

  no ip proxy-arp

  IP nat inside

  route CUSTOMGATE card intellectual property policy

  automatic duplex

  automatic speed

  !

  IP local pool ippool 10.172.10.100 10.172.10.200

  IP nat inside source map route sheep interface FastEthernet0/0 overload

  no ip address of the http server

  no ip http secure server

  IP classless

  IP route 0.0.0.0 0.0.0.0 10.0.0.30

  access-list 100 deny ip 10.0.0.0 0.0.0.255 10.172.10.0 0.0.0.255

  access-list 100 permit ip 10.0.0.0 0.0.0.255 any

  username password XXX 7 XXXXXX

  AAA new-model

  !

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  AAA - the id of the joint session

  IP subnet zero

  !

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  Configuration group customer crypto isakmp XXXX

  key XXXXX

  pool ippool

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  !

  interface Loopback1

  192.168.254.1 IP address 255.255.255.0

  !

  interface FastEthernet0/0

  IP address 200.x.x.x 255.255.x.x

  no ip proxy-arp

  NAT outside IP

  automatic duplex

  automatic speed

  clientmap card crypto

  !

  interface FastEthernet0/1

  the IP 10.0.0.1 255.255.255.0

  no ip proxy-arp

  IP nat inside

  route CUSTOMGATE card intellectual property policy

  automatic duplex

  automatic speed

  !

  IP local pool ippool 10.172.10.100 10.172.10.200

  IP nat inside source map route sheep interface FastEthernet0/0 overload

  no ip address of the http server

  no ip http secure server

  IP classless

  IP route 0.0.0.0 0.0.0.0 10.0.0.30

  IP route 20.x.x.x 255.255.255.255 200.x.x.x (it is here to let him speak to the customer)

  access-list 100 deny ip 10.0.0.0 0.0.0.255 10.172.10.0 0.0.0.255

  access-list 100 permit ip 10.0.0.0 0.0.0.255 any

  access-list 110 deny host ip 10.0.0.73 10.1.0.0 0.0.0255

  access-list 110 permit ip 10.0.0.73 host everything

  !

  CUSTOMGATE allowed 10 route map

  corresponds to the IP 110

  IP 200.x.x.x next value break

  !

  sheep allowed 10 route map

  corresponds to the IP 100

  !

  !

  CUSTOMGATE allowed 10 route map

  corresponds to the IP 110

  IP 200.x.x.x next value break

  !

  sheep allowed 10 route map

  corresponds to the IP 100

  !

  Add at least:

  > Route ip 10.172.10.0 255.255.255.0 200.x.x.x

  to force the traffic for VPN clients on the external interface. also make sure you hav a route for the clients IP address (not the VPN negotiated one) that also indicates the external interface.

  The fact that the router is not encrypt means that it is not even see the responses from the inside, hosts, which indicates that your internal network is not a road to 10.172.10.0 pointing to this router, OR the router receives responses but sends them back out inside interface which will be set by the first route, I mentioned above.

• VPN - PC (vpn client) problem-> router-> (site to site vpn)-> local network

  Hello

  is it possible to install?

  I have a pc and I want to connect to the Remote LAN.

  PC (using vpn client) - vpn (internet)---> ROUTER1 - a vpn (MPLS network)---> ROUTER2---> SERVER site

  How can I connect to a remote server? Is there an easy way?

  I did the configuration of the vpn client (I can connect ROUTER1 and access a LAN via vpn with 192.168.1.x), but I can't connect to the server, even if I set the subnet (192.168.1.x) under the access list of site to site vpn (access list for traffic that must pass between ROUTER1 and ROUTER2).

  Please advise! Thanks in advance.

  Looks like I've not well explained.

  On ROUTER1

  ===================

  1 ACL VNC_acl is used to split tunnel, so you should include IP server_NET it NOT vpn IP pool.

  2 ACL najavorbel is used to set the lan lan traffic between ROUTER1 and ROUTER2, 2 you should inlcude

  IP 192.168.133.0 allow 0.0.0.255 0.0.0.255

  You must change the crypto ROUTER2 ACL of the minor or the najavorbel of the ACL

  The other way to is to the client VPN NAT IP to a local area network lan IP ROUTER1, in this way, you don't need any changes on ROUTER2. But I have to take a look at your configuration to make the suggestion.

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• Client VPN connectivity problems

  I use the cisco VPN client to connect to our network, located behind a 515E. The client is authenticated and gets an ip address but cannot ping or connect with one of the hosts. The connection is to a network of customers that is also behind a 515E. I have successfully connected using the same policy to other places and have had no problem. What confuses me, is that we have used to have a Netscreen firewall before and he had a netscreen vpn client which connected since their network with a problem. Is that something they need for their firewall so that we can get through the traffic?

  Try to turn on NAT - T on your pix, by setting up:

  ISAKMP nat-traversal 20

  and configure the client vpn accordingly:

  http://www.Cisco.com/warp/public/471/cvpn_3k_nat.html#conf_client

  I think these discussions are useful:

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=virtual%20Private%20Networks&topic=General&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1dd7dda4

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=virtual%20Private%20Networks&topic=General&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1dd7fe80

• Routing problem between the VPN Client and the router's Ethernet device

  Hello

  I have a Cisco 1721 in a test environment.

  A net 172.16.0.0/19 simulates the Internet and a net 192.168.1.0/24 simulates the net, the VPN tunnel must go to (intranet).

  The net 172.16.0.0 depends on the router 0 FastEthernet, Intranet (VPN) hangs on Ethernet 0.

  The configuration was inspired form the sample Configuration

  "Configuring the Client VPN Cisco 3.x for Windows to IOS using Local extended authentication"

  and the output of the ConfigMaker configuration.

  Authentication and logon works. Client receives an IP address from the pool. But there's a routing problem

  side of routers. Ping client-side - do not work (the VPN client statistics that count encrypt them packets, but not to decrypt).

  Ping the router works too, but decrypt and encrypt customer statistics in VPN packets count progressive

  (customer has a correct route and return ICMP packets to the router).

  The question now is:

  How to route packets between the Tunnel and an Ethernet device (Ethernet 0)?

  conf of the router is attached - hope that's not too...

  Thanks & cordially

  Thomas Schmidt

  -.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.- snipp .-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.

  !

  version 12.2

  horodateurs service debug uptime

  Log service timestamps uptime

  encryption password service

  !

  !

  host name * moderator edit *.

  !

  enable secret 5 * moderator edit *.

  !

  !

  AAA new-model

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  !

  ! only for the test...

  !

  username cisco password 0 * moderator edit *.

  !

  IP subnet zero

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  crypto ISAKMP policy 3

  3des encryption

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group 3000client

  key cisco123

  pool ippool

  !

  ! We do not want to divide the tunnel

  ! ACL 108

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  interface Ethernet0

  no downtime

  Description connected to VPN

  IP 192.168.1.1 255.255.255.0

  full-duplex

  IP access-group 101 in

  IP access-group 101 out

  KeepAlive 10

  No cdp enable

  !

  interface Ethernet1

  no downtime

  address 192.168.3.1 IP 255.255.255.0

  IP access-group 101 in

  IP access-group 101 out

  full-duplex

  KeepAlive 10

  No cdp enable

  !

  interface FastEthernet0

  no downtime

  Description connected to the Internet

  IP 172.16.12.20 255.255.224.0

  automatic speed

  KeepAlive 10

  No cdp enable

  !

  ! This access group is also only for test cases!

  !

  no access list 101

  access list 101 ip allow a whole

  !

  local pool IP 192.168.10.1 ippool 192.168.10.10

  IP classless

  IP route 0.0.0.0 0.0.0.0 172.16.12.20

  enable IP pim Bennett

  !

  Line con 0

  exec-timeout 0 0

  password 7 * edit from moderator *.

  line to 0

  line vty 0 4

  !

  end

  ^-^-^-^-^-^-^-^-^-^-^-^-^- snapp ^-^-^-^-^-^-^-^-^-^-^-^-^-^-

  Thomas,

  Can't wait to show something that might be there, but I don't see here. You do not have the card encryption applied to one of the interfaces, perhaps it was not copied. Assuming your description you do it, or should it be, applied to the fa0 and you are connected. Try how you ping? Since the router or a device located on E0? If you ping the router, you will need to do an extended ping of E0 to the ip address of the client has been assigned. If your just ping the router without the extension, you will get sales and decrypts that you declare on the client. Have you tried to ping from the client to interface E0? Your default route on the router is pointing to fa0? You have a next hop to affect? You have several NIC on the client pc? Turn off your other network cards to check that you don't have a problem with routing on the client if you have more than one.

  Kurtis Durrett

• VPN clients cannot access remote sites - PIX, routing problem?

  I have a problem with routing to remote from our company websites when users connect via their VPN client remotely (i.e. for home workers)

  Our headquarters contains a PIX 515E firewall. A number of remote sites to connect (via ADSL) to head office using IPSEC tunnels, ending the PIX.

  Behind the PIX is a router 7206 with connections to the seat of LANs and connections to a number of ISDN connected remote sites. The default route on 7206 points to the PIX from traffic firewall which sits to ADSL connected remote sites through the PIX. Internal traffic for LAN and ISDN connected sites is done via the 7206.

  Very good and works very well.

  When a user connects remotely using their VPN client (connection is interrupted on the PIX) so that they get an IP address from the pool configured on the PIX and they can access resources located on local networks to the office with no problems.

  However, the problem arises when a remote user wants access to a server located in one of the remote sites ADSL connected - it is impossible to access all these sites.

  On the remote site routers, I configured the access lists to allow access from the pool of IP addresses used by the PIX. But it made no difference. I think that the problem may be the routes configured on the PIX itself, but I don't know what is necessary to solve this problem.

  Does anyone have suggestions on what needs to be done to allow access to remote sites for users connected remotely via VPN?

  (Note: I suggested a workaround, users can use a server on LAN headquarters as a "jump point" to connect to remote servers from there)

  with pix v6, no traffic is allowed to redirect to the same interface.

  for example, a remote user initiates an rdp session for one of the barns adsl. PIX decrypts the packet coming from the external interface and looks at the destination. because the destination is one of adsl sites, pix will have to return traffic to the external interface. Unfortunately, pix v6.x has a limitation that would force the pix to drop the packet.

  with the v7, this restriction has been removed with the "same-security-traffic control intra-interface permits".

  http://www.Cisco.com/en/us/partner/products/HW/vpndevc/ps2030/products_configuration_example09186a008046f307.shtml

• Cisco AnyConnect VPN Client (connection attempt failed because the network or pc problem cisco)

  Hi all

  I am trying to connect to my Cisco AnyConnect VPN Client but everytime I try, I get an error (connection attempt failed because the network or pc problem cisco)

  Can anyone help me please with this.

  Thank you

  Zia

  What is the local firewall on your computer?

• IPSec site to site VPN cisco VPN client routing problem and

  Hello

  I'm really stuck with the configuration of ipsec site to site vpn (hub to spoke, multiple rays) with cisco vpn remote client access to this vpn.

  The problem is with remote access - cisco vpn client access - I can communicate with hub lan - but I need also communication of all lans speaks of the cisco vpn client.

  There are on the shelves, there is no material used cisco - routers DLINK.

  Someone told me that it is possible to use NAT to translate remote access IP-lan-HUB customers and thus allow communication - but I'm unable to set up and operate.

  Can someone help me please?

  Thank you

  Peter

  RAYS - not cisco devices / another provider

  Cisco 1841 HSEC HUB:

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key x xx address no.-xauth

  !

  the group x crypto isakmp client configuration

  x key

  pool vpnclientpool

  ACL 190

  include-local-lan

  !

  86400 seconds, duration of life crypto ipsec security association

  Crypto ipsec transform-set esp-3des esp-sha-hmac 1cisco

  !

  Crypto-map dynamic dynmap 10

  Set transform-set 1cisco

  !

  card crypto ETH0 client authentication list userauthen

  card crypto isakmp authorization list groupauthor ETH0

  client configuration address card crypto ETH0 answer

  ETH0 1 ipsec-isakmp crypto map

  set peer x

  Set transform-set 1cisco

  PFS group2 Set

  match address 180

  card ETH0 10-isakmp ipsec crypto dynamic dynmap

  !

  !

  interface FastEthernet0/1

  Description $ES_WAN$

  card crypto ETH0

  !

  IP local pool vpnclientpool 192.168.200.100 192.168.200.150

  !

  !

  overload of IP nat inside source list LOCAL interface FastEthernet0/1

  !

  IP access-list extended LOCAL

  deny ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  deny ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  IP 192.168.7.0 allow 0.0.0.255 any

  !

  access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  !

  How the DLINK has been configured for traffic between the site to site VPN subnets? You are able to add multiple remote subnets on DLINK? If you can, then you must add the pool of Client VPN subnet.

  Alternatively, if you cannot add multiple subnet on DLINK router, you can change the pool of Client VPN 192.168.6.0/24, and on the crypto ACL between the site to site VPN, you must edit the 180 existing ACL

  DE:

  access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 180 allow ip 192.168.200.0 0.0.0.255 192.168.1.0 0.0.0.255

  TO:

  access-list 180 allow ip 192.168.6.0 0.0.1.255 192.168.1.0 0.0.0.255

  Also change the ACL 190 split tunnel:

  DE:

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.200.0 0.0.0.255

  TO:

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.6.0 0.0.0.255

  access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.6.0 0.0.0.255

  Finally, replace the remote subnet 192.168.7.0/255.255.255.0 192.168.6.0/255.255.254.0 DLINK.

  Hope that helps.

• 1710 VPN and VPN Client - routing problem '' maybe. ''

  Hello

  I was able to get with 3DES and CISCO VPN Client 3.6.1 1710. with permission of local aaa.

  When I am connected to the VPN I can ping to the IP address of the VPN router

  (24.x.x.x.) and I can ping to the router's internal interface (192.168.x.x).

  The problem is that I can't ping anything else - for example: hosts in the enterprise network (192.168.x.x).

  Configuration:

  The router's internal IP address: 192.168.x.x

  The router's external IP address: 24.x.x.x

  ippool for customers: 10.10.10.x

  The IP address of the Client after the connection is correct: 10.0.0.x (from pool)

  Maybe I'm missing something in 1710 confg? I have NAT interface internal? The default gateway of the net is FreeBSD, not the router of 1710 system.

  All ideas are welcome.

  Miro Pendev

  TI Administrstor

  Quite often, you will lose the first ping because an ARP must be sent and responded to, but if you get the subsequent pings, then it's OK.

  For what is able to browse the Internet while the tunnel is up, you must enable split tunneling. Add the following:

  > access-list 110 permit ip 192.168.1.0 0.0.0.255 192.168.1.0 0.0.0.255

  > isakmp crypto client configuration group my_usergroup

  > acl 110

  This means that the client will only encrypt the traffic to the 192.168.1.0 network, all other traffic shuts down in the clear on the Internet.