Cisco 2621 to VPN client problem

Similar Questions

• Cisco and Checkpoint VPN clients on a single PC

  Hello

  I'm in the following fix:

  I had used customer Checkpoint SecuRemote 4.1 SP - 5 VPN in the past.

  Now, I have installed the Cisco VPN client version 4.0.4 on my PC to access IPSec VPN for the PIX in our headquarters.

  According to Cisco VPN release notes http://www.cisco.com/univercd/cc/td/doc/product/vpn/client/rel404/404clnt.htm#wp1346340 , it should be possible to have clients both Cisco and Checkpoint VPN installed on the same machine.

  But I am not able to connect to my PIX, I receive the following error message:

  "Secure the complete VPN connection locally by the Client.

  Reason 403: failed to contact the security gateway. »

  When I'm looking for signs of PC control-> system-> hardware-> device Administration-> network cards, I can see Cisco Systems VPN Adapter disabled.

  After you activate manually, I always get the same error when you try to connect to the Cisco VPN client.

  After PC restart the Cisco VPN adapter is disabled later.

  I tried to uncheck Check Point SecuRemote form my Dial-up connection (bypassing CSCea31192 of bug, but the bug does not affect NAT - T connection which I use).

  I noticed the same situation on three different computers, one running Windows XP, both running Windows 2000.

  After uninstalling the client Checkpoint completely (including Windows registry manual removal), the Cisco VPN client works very well.

  It seems to me, therefore, that there is a profound mismatch between Cisco and Checkpoint VPN clients.

  Does anyone know of a workaround?

  Thank you

  Milan

  We had the same problem with some of our users who need to use the two clients to connect to customer sites.

  If I remember the cisco client does not start automatically, but the client of checkpoint 4.1 don't.

  We by-passed by deleting the registry entry point control that starts the client at startup. fwenc.exe is the entrance and it is in

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Run

  After that make a shortcut to the executable file that is stored in the directory \bin to relevant checkpoint on the client (it is different from NT & 9 client x) and then only start when it is necessary.

  Hope that's a help

• Windows 7 64 bit VPN client problems

  Hello

  I am running Windows 7 Professional 64 bit and Cisco VPN client 5.0.07.0240. I am able to connect to my corporate network and work ok but connection is very slow!

  Connection time is distributed as follows:

  Client program VPN Opening: 70 seconds.

  Click on connect and wait for the user credentials dialog box: 30 seconds.

  Enter the credentials, and then click ok then 'user authentication': 90 seconds.

  "Negotiate security policies": 60 seconds.

  User area credentials if poster again, re - enter the credentials that the dialog box is empty, and then click ok: 90 seconds.

  "User authentication", then connection established: 120 seconds.

  I have a colleague running 64-bit Windows 7 (ultimate edition) which uses the same version and does not have these problems.

  Any ideas anyone?

  See you soon,.

  Gary

  Gary, thanks for the update. If disabling the firewall and restart vpn service did not help. Could you please try and install the 5.0.07.0290 version?

  Before do you, I would like to know if you import .pcf for the VPN Client files. If so, please try to re-create a file .pcf on the PC and try and use this file to connect. Also, I see that the existing .pcf file you are using is a file read-only. Could you change this and give permissions to write to the file, and try to connect. If th does not help the two steps will then install the 5.0.07.0290 version.

  Thank you

  Delvallée

• VPN client problem long transfer of files with VPN3000

  I have problems transferring big files (more than 4 MB) using customer vpn 4.8.02 or 5.0 with vpn3020 4.7.2.N

  It happens the question with MTU. Try reducing the MTU value by running the file setMTU.exe on the VPN client. Make sure you do not fragment bit is not set on the intermediate routers. For setting MTU on VPN 3000 refer URL http://www.cisco.com/en/US/products/hw/vpndevc/ps2284/products_configuration_guide_book09186a00800d81b3.html

• VPN access with VPN client problem. Help, please

  I have a PIX 520 as VPN tunnels endpoint device. I was able to establish an IPsec connection. I checked that I have gave me an address in the IP pool that I set up but I can't to any resource on the internal network. I could only ping myself. When I run ' ipconfig/all' I see my address on the correct vpn with DNS interface, but my front door is set to my own address. I think that's the problem. Please help me solve this problem. Let me know if you need more information.

  Here are some suggestions you might try to get this working:

  1.) change your "taken" to access-list. The lines are no longer supported by Cisco even if they still work. This will help you in debugging your access list because there will be some hitcounts.

  There is a tool from cisco for conduits of concert on access lists:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/PIX?sort=release

  Download the: occ - 121.zip

  PIX Firewall Outbound leads binary converter for Windows, version 1.2.1

  2.) change your pool of VPN.

  IP local pool techvpn 10.x.x.100 - 10.x.x.120

  With this, it's already you have a 10.x.x.x subnet in your internal network. The ip pool automatically assigns a 255.0.0.0 for the VPN Clients subnet mask. This may cause routing problems. You can use a subnet used anywhere 172.16.100.x.

  example:

  No vpngroup address techvpn pool lsdvpn

  no ip local pool techvpn

  IP local pool techvpn 172.16.100.1 - 172.16.100.254

  vpngroup address techvpn pool lsdvpn

  No inside_outbound_nat0_acl access list

  No outside_cryptomap_dyn_20 access list

  inside_outbound_nat0_acl ip access list allow any 172.16.100.0 255.255.255.0

  outside_cryptomap_dyn_20 ip access list allow any 172.16.100.0 255.255.255.0

  Claire ipsec his

  Claire isakmp his

  sincerely

  Patrick

• % 305013-5-ASA: rules asymmetrical NAT matched for flows forward and backward; Connection refused because of the failure of the path opposite. NAT VPN clients problems after that put 8.3.2 to level.

  I've recently updated to 8.3.2 and I have been informed of these NAT changes, but even after reading the https://supportforums.cisco.com/docs/DOC-12569 I am still unable to rectify the communication network 192.168.100.0 VPN with hosts on 172.16.1.0 and 172.16.9.0. VPN clients connect to the external interface, and I try to ping inside and the demilitarized zone, respectable 172.16.1.0 and 172.16.9.0 hosts. VPN client shows that the two previously mentioned networks such as roads of security, but still not to the ping pong.

  # sh nat

  Manual NAT policies (Section 1)

  1 (inside) to the (whole) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  2 (inside) to the (whole) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  3 (inside) to the (whole) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - 172.16.12.0 obj - one-way 172.16.12.0

  translate_hits = 0, untranslate_hits = 0

  4 (dmz) to (outside) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  5 (dmz) to (outside) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - 172.16.12.0 obj - one-way 172.16.12.0

  translate_hits = 0, untranslate_hits = 0

  Auto NAT policies (Section 2)

  1 (dmz), to the source (external) static obj - 172.16.9.5 interface tcp www www service

  translate_hits = 0, untranslate_hits = 142

  2 (dmz) (outdoor) source static obj - 172.16.9.5 - 01 interface service tcp 3389 3389

  translate_hits = 0, untranslate_hits = 2

  3 (dmz) (outdoor) source static obj - 172.16.9.5 - 02 interface tcp ldap ldap service

  translate_hits = 0, untranslate_hits = 0

  4 (dmz) (outdoor) source static obj interface - 172.16.9.5 - 03 service ftp ftp tcp

  translate_hits = 0, untranslate_hits = 0

  5 (dmz) to (outside) of the source static obj - 172.16.9.5 - 04 interface tcp smtp smtp service

  translate_hits = 0, untranslate_hits = 267

  6 (inside) source static obj - 172.16.9.0 172.16.9.0 (dmz)

  translate_hits = 4070, untranslate_hits = 224

  7 (inside) to (dmz) source static obj - 10.1.0.0 10.1.0.0

  translate_hits = 0, untranslate_hits = 0

  8 (inside) to (dmz) source static obj - 172.16.0.0 172.16.0.0

  translate_hits = 152, untranslate_hits = 4082

  9 (dmz) to dynamic interface of the obj - 172.16.9.0 - 01 source (outdoor)

  translate_hits = 69, untranslate_hits = 0

  10 (inside) to the obj_any interface dynamic source (external)

  translate_hits = 196, untranslate_hits = 32

  I think you must following two NAT config

  NAT (inside, outside) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - 192.168.100.0 obj - 192.168.100.0
  NAT (dmz, external) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - 192.168.100.0 obj - 192.168.100.0

  Please configure them and remove any additional NAT configuration and then try again.

• BSOD with VPN Client problem

  I use the VPN Client 5.0.06.0110 to connect to my computer at home at my desk, which has an ASA5505.  If my immediate network to the client PC connection is lost while the VPN is active, I get a BSOD.  There is no problem if my grave DSL or a cable beyond my router is disconnected.  He only (and always) will fail if the network cable to the computer running the VPN Client is cut (or if my router loses power), while the link is connected.

  I am running:

  Windows 7 (all updates installed)

  Pentium Core 2

  4 GB of ram

  Atheros L1 Gigabit 10/100/1000 controller

  Any suggestion would be appreciated.

  BTW, here is the description for your reference:

  PC restarts if physical link is disrupted when a VPN connection

  Symptom: Restart the computer (the user can also see a Blue Screen Of Death (BSOD) before the reboot, based on the setup of the PC) if the physical link is disrupted when a VPN connection (that is when you see the error message "a network cable is unplugged).  This can occur if you run "shutdown" on your PC is connected to the way of the switch, turn off the SOHO router (or switch) the PC is connected to, lose your WiFi connection, or even disconnect the LAN cable to your wired Ethernet port. Conditions: Loss of physical connection during a VPN connection.

• VPN - PC (vpn client) problem-> router-> (site to site vpn)-> local network

  Hello

  is it possible to install?

  I have a pc and I want to connect to the Remote LAN.

  PC (using vpn client) - vpn (internet)---> ROUTER1 - a vpn (MPLS network)---> ROUTER2---> SERVER site

  How can I connect to a remote server? Is there an easy way?

  I did the configuration of the vpn client (I can connect ROUTER1 and access a LAN via vpn with 192.168.1.x), but I can't connect to the server, even if I set the subnet (192.168.1.x) under the access list of site to site vpn (access list for traffic that must pass between ROUTER1 and ROUTER2).

  Please advise! Thanks in advance.

  Looks like I've not well explained.

  On ROUTER1

  ===================

  1 ACL VNC_acl is used to split tunnel, so you should include IP server_NET it NOT vpn IP pool.

  2 ACL najavorbel is used to set the lan lan traffic between ROUTER1 and ROUTER2, 2 you should inlcude

  IP 192.168.133.0 allow 0.0.0.255 0.0.0.255

  You must change the crypto ROUTER2 ACL of the minor or the najavorbel of the ACL

  The other way to is to the client VPN NAT IP to a local area network lan IP ROUTER1, in this way, you don't need any changes on ROUTER2. But I have to take a look at your configuration to make the suggestion.

• VPN Client problem

  A remote user on our network has problems with the Cisco VPN. They are using Win XP, Cisco Client 3.5.2 and connect via a router of Compaq Ipaq into a modem cable. When they VPN in our 3000 VPN concentrator works very well. When they try to VPN in the PIX on our network, it indicates that the client is no longer. If they use a Microsoft VPN to connect to the network with the 3000 (we run both MS and Cisco VPN) with it set to use the remote control, the default gateway, the Cisco VPN will connect to the PIX, see the network behind PIX, ping stuff behind the PIX, but not map a drive. The remote user can ping the PIX of their unVPNed in the remote location. No other user is a problem connecting to the PIX (except those with the bad remote access or broadband satellite which cannot VPN into anything anyway). We have even a few AOLer connect to it. Help me please.

  If the compaq ipaq router makes a PAT, that might be the problem. PIX is unable to manage the ipsec clients who crossed pat. The vpn3000 has some mechanism to deal with this. PPTP is different to ipsec.

  You must ensure that the ipsec client has its own public routable ip address.

  Kind regards

• Cisco asa anyconnect vpn client mode issue

  Hi team,

  I get my users anyconnect vpn connection failures very frequently and it that comesup.

  Can you please check see the version attached and explain, if I run with licenses right into place.

  concerning

  SecIT

  Hello

  You've got license for 250 users anyconnect so unless you are having more users than this number, it shouldn't be a problem. Debugs could help reduce the problem in this case.

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• Cisco VPN Client is blocking incoming connections

  Hello

  I somethimes (not always) a problem with the Cisco VPN Client.

  As soon as the CISCO VPN Client is installed (it must not be running) it blocks inbound connections from the local network.

  The problem is that I use Ultra VNC SC to support some of my clients. Another client is supported by Cisco VPN. With UltraVNC SC customer clients try to connect to my PC.

  But if I installed the cisco VPN Client, no incoming connections are possible.

  How can I change this behavior?

  This behavior is not always the same. Last incoming connections of two months were possible, but from one day to another is not possible more.

  I recently installed the Client, but it takes no effect :-(

  I have NOT activated the firewall Cisco on the VPN Client and the behavior is NOT only if the Client is activated. This is the behavior even if it is NOT active and just installed.

  Hi Chris,

  Zone alarm is installed on the PC that is defective?

  Try to restart the Cisco VPN service and launch the vpn client.

  I remember having a similar problem with the Cisco VPN Client. Some conflict between the VPN client and Zone-Alarm, installed on the same PC.

  The problem was with VSDATANT variables in the registry key.

  Please see the following mail took from another forum:

  http://www.OutpostFirewall.com/Forum/showthread.php?t=9917

• No documentation for worm VPN clients. 5

  Hello

  Why it seems that there is no documentation on the Cisco site for VPN clients past version 4.6? There are release notes, but no user guide. We recently bought an ASA, but the accompanying CD has an older version of client.

  Thank you

  -Steve

  Steve,

  Yes, you are right. There is no new documentation for the 4.8, 4.9 and 5.0.00.0340 to output other than the text release notes posted with the VPN Client.

  The reason is, other than new features to support some new OS (Vista 32 Bit OS), etc., between 4.6 and 5.0 configuration steps are the same. Then you should be good to go with the 4.6 Setup guide. If this is a new Client VPN deployment, I go through the detailed release notes and be aware of known issues that may affect your network.

  Kind regards

  Arul

  * Please Note If this can help *.

• termination of VPN client 4.0 on pix 515

  I am trying to connect the cisco 4.0 vpn client to a worm of pix 515 6.1 and receive as a result of errors that I guess are the related hashing algorithm but am not sure. Only DES is not enabled 3DES. Config output Cisco post interprets but apparently no error in config.

  Journal of VPN client:

  Cisco Systems VPN Client Version 4.0 (Rel)

  Copyright (C) 1998-2003 Cisco Systems, Inc. All rights reserved.

  Customer type: Windows, Windows NT

  Running: 5.0.2195

  1 10:58:34.890 25/09/03 Sev = Info/4 CM / 0 x 63100002

  Start the login process

  2 10:58:34.906 25/09/03 Sev = Info/4 CVPND/0xE3400001

  Microsoft's IPSec Policy Agent service stopped successfully

  3 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100004

  Establish a connection using Ethernet

  4 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100024

  Attempt to connect with the server "x.x.x.226".

  5 10:58:35.953 25/09/03 Sev = Info/6 IKE/0x6300003B

  Attempts to establish a connection with x.x.x.226.

  6 10:58:36.000 25/09/03 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Nat - T), VID (Frag), VID (Unity)) at x.x.x.226

  7 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700008

  IPSec driver started successfully

  8 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  9 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  10 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226

  11 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  12 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226

  13 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  14 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226

  15 10:58:56.093 25/09/03 Sev = Info/4 IKE / 0 x 63000017

  Marking of IKE SA delete (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  16 10:58:56.593 25/09/03 Sev = Info/4 IKE/0x6300004A

  IKE negotiation to throw HIS (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  17 10:58:56.593 25/09/03 Sev = Info/4 CM / 0 x 63100014

  Could not establish the Phase 1 SA with the server 'x.x.x.226' due to the 'DEL_REASON_PEER_NOT_RESPONDING '.

  18 10:58:56.593 25/09/03 Sev = Info/5 CM / 0 x 63100025

  Initializing CVPNDrv

  19 10:58:56.593 25/09/03 Sev = Info/4 IKE / 0 x 63000001

  Signal received IKE to complete the VPN connection

  20 10:58:56.625 25/09/03 Sev = critique/1 CVPND/0xE3400001

  Service Microsoft's IPSec Policy Agent started successfully

  21 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  22 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  23 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  24 10:58:57.093 25/09/03 Sev = Info/4 IPSEC/0x6370000A

  IPSec driver successfully stopped

  Journal of Pix:

  crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226

  Peer VPN: ISAKMP: approved new addition: ip:x.x.x.194 Total VPN peer: 1

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 1 Total VPN EEP

  RS: 1

  Exchange OAK_AG

  ISAKMP (0): treatment ITS payload. Message ID = 0

  ISAKMP (0): audit ISAKMP transform 1 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: hash SHA

  ISAKMP: default group 2

  ISAKMP: preshared extended auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform against the policy of priority 1 2

  ISAKMP: encryption... What? 7?

  ISAKMP: MD5 hash

  ISAKMP: default group 2

  ISAKMP: preshared extended auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 3 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: hash SHA

  ISAKMP: default group 2

  ISAKMP: preshared auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 4 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: MD5 hash

  ISAKMP: default group 2

  ISAKMP: preshared auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 5 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: hash SHA

  ISAKMP: default group 2

  ISAKMP: preshared extended auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 6 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: MD5 hash

  ISAKMP: default group 2

  ISAKMP: preshared extended auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 7 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: hash SHA

  ISAKMP: default group 2

  ISAKMP: preshared auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 8 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: MD5 hash

  ISAKMP: default group 2

  ISAKMP: preshared auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 9 against the policy of priority 1

  ISAKMP: 3DES-CBC encryption

  ISAKMP: hash SHA

  ISAKMP: default group 2

  ISAKMP: preshared extended auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4

  crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP

  RS: 1

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP

  RS: 1

  crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP

  RS: 1

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP

  RS: 1

  ISAKMP (0): retransmission of phase 1...

  ISAKMP (0): retransmission of phase 1...

  ISAKMP (0): delete SA: src x.x.x.194 dst x.x.x.226

  ISADB: Reaper checking HIS 0x80db91c8, id_conn = 0 DELETE IT!

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 0 Total of VPN EEP

  RS: 1

  Peer VPN: ISAKMP: deleted peer: ip:x.x.x.194 VPN peer Total: 0

  ISAKMP: Remove the peer node for x.x.x.194

  Thanks for any help

  Hello

  Pix isakmp policy should have DES, MD5, and group 2 for the 4.x to connect Cisco VPN client, these are proposals that the client sends to the server...

  http://www.Cisco.com/univercd/CC/TD/doc/product/VPN/client/rel4_0/admin_gd/vcach6.htm#1157757

  This link will show you IKE proposals be configured on the PIX (VPN server)

  Arthur

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• Cisco AnyConnect VPN Client (connection attempt failed because the network or pc problem cisco)

  Hi all

  I am trying to connect to my Cisco AnyConnect VPN Client but everytime I try, I get an error (connection attempt failed because the network or pc problem cisco)

  Can anyone help me please with this.

  Thank you

  Zia

  What is the local firewall on your computer?