VPN client problem long transfer of files with VPN3000

Similar Questions

• Windows XP - a problem to transfer big file from laptop on an external hard drive

  I have a problem to transfer large files (mail.pst - zipped file - 5Gbyte) of the laptop (Dell Latitude D630) on an external hard drive (WD 320 G - FAT 32) where each time, I got the message "there is not enough free space on the disk" although I did successfully drive clean on both sides and there is enough space on both sides (not less than 25 GB).

  Also, I did a checkdisk command and he succeeded, and I use Windows XP

  I did several tests to resolve and in the end, I found that I convert the format of external hard drive FAT 32 to NTFS, and then I could successfully transfer the file.

  I used the following commands:

  (1) command line then chkdsk to repair bad sectors

  (2) convert the command line to change the format to FAt 32 to NTFS

  Note: For Windows xp, "convert" command will not delete the files from the hard drive

• VPN access with VPN client problem. Help, please

  I have a PIX 520 as VPN tunnels endpoint device. I was able to establish an IPsec connection. I checked that I have gave me an address in the IP pool that I set up but I can't to any resource on the internal network. I could only ping myself. When I run ' ipconfig/all' I see my address on the correct vpn with DNS interface, but my front door is set to my own address. I think that's the problem. Please help me solve this problem. Let me know if you need more information.

  Here are some suggestions you might try to get this working:

  1.) change your "taken" to access-list. The lines are no longer supported by Cisco even if they still work. This will help you in debugging your access list because there will be some hitcounts.

  There is a tool from cisco for conduits of concert on access lists:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/PIX?sort=release

  Download the: occ - 121.zip

  PIX Firewall Outbound leads binary converter for Windows, version 1.2.1

  2.) change your pool of VPN.

  IP local pool techvpn 10.x.x.100 - 10.x.x.120

  With this, it's already you have a 10.x.x.x subnet in your internal network. The ip pool automatically assigns a 255.0.0.0 for the VPN Clients subnet mask. This may cause routing problems. You can use a subnet used anywhere 172.16.100.x.

  example:

  No vpngroup address techvpn pool lsdvpn

  no ip local pool techvpn

  IP local pool techvpn 172.16.100.1 - 172.16.100.254

  vpngroup address techvpn pool lsdvpn

  No inside_outbound_nat0_acl access list

  No outside_cryptomap_dyn_20 access list

  inside_outbound_nat0_acl ip access list allow any 172.16.100.0 255.255.255.0

  outside_cryptomap_dyn_20 ip access list allow any 172.16.100.0 255.255.255.0

  Claire ipsec his

  Claire isakmp his

  sincerely

  Patrick

• BSOD with VPN Client problem

  I use the VPN Client 5.0.06.0110 to connect to my computer at home at my desk, which has an ASA5505.  If my immediate network to the client PC connection is lost while the VPN is active, I get a BSOD.  There is no problem if my grave DSL or a cable beyond my router is disconnected.  He only (and always) will fail if the network cable to the computer running the VPN Client is cut (or if my router loses power), while the link is connected.

  I am running:

  Windows 7 (all updates installed)

  Pentium Core 2

  4 GB of ram

  Atheros L1 Gigabit 10/100/1000 controller

  Any suggestion would be appreciated.

  BTW, here is the description for your reference:

  PC restarts if physical link is disrupted when a VPN connection

  Symptom: Restart the computer (the user can also see a Blue Screen Of Death (BSOD) before the reboot, based on the setup of the PC) if the physical link is disrupted when a VPN connection (that is when you see the error message "a network cable is unplugged).  This can occur if you run "shutdown" on your PC is connected to the way of the switch, turn off the SOHO router (or switch) the PC is connected to, lose your WiFi connection, or even disconnect the LAN cable to your wired Ethernet port. Conditions: Loss of physical connection during a VPN connection.

• Windows 7 64 bit VPN client problems

  Hello

  I am running Windows 7 Professional 64 bit and Cisco VPN client 5.0.07.0240. I am able to connect to my corporate network and work ok but connection is very slow!

  Connection time is distributed as follows:

  Client program VPN Opening: 70 seconds.

  Click on connect and wait for the user credentials dialog box: 30 seconds.

  Enter the credentials, and then click ok then 'user authentication': 90 seconds.

  "Negotiate security policies": 60 seconds.

  User area credentials if poster again, re - enter the credentials that the dialog box is empty, and then click ok: 90 seconds.

  "User authentication", then connection established: 120 seconds.

  I have a colleague running 64-bit Windows 7 (ultimate edition) which uses the same version and does not have these problems.

  Any ideas anyone?

  See you soon,.

  Gary

  Gary, thanks for the update. If disabling the firewall and restart vpn service did not help. Could you please try and install the 5.0.07.0290 version?

  Before do you, I would like to know if you import .pcf for the VPN Client files. If so, please try to re-create a file .pcf on the PC and try and use this file to connect. Also, I see that the existing .pcf file you are using is a file read-only. Could you change this and give permissions to write to the file, and try to connect. If th does not help the two steps will then install the 5.0.07.0290 version.

  Thank you

  Delvallée

• Broken screen - problems of transfer of files on USB stick due to the "read-only".

  I have a screen broke on my G2 bike. I can turn the phone on and off, but I can't get past my password because the screen is unresponsive. When I connect the phone to my pc via the usb port I can still access the files because of the default value to "charge only".

  Does anyone know of a way to change my phone to another parameter as 'charge only' that does not involve the use of the touch screen?

  I tried to use adb to transfer my files using the android devices Manager or command prompt but usb debugging is disabled.

  Even if usb debugging was, would not be required to change the settings for usb 'charge only' in order for my pc to detect the phone?

  The otg worked perfectly. With the help of a mouse instead of the touch screen, I was able to activate the bluetooth and transfer the files this way.

• % 305013-5-ASA: rules asymmetrical NAT matched for flows forward and backward; Connection refused because of the failure of the path opposite. NAT VPN clients problems after that put 8.3.2 to level.

  I've recently updated to 8.3.2 and I have been informed of these NAT changes, but even after reading the https://supportforums.cisco.com/docs/DOC-12569 I am still unable to rectify the communication network 192.168.100.0 VPN with hosts on 172.16.1.0 and 172.16.9.0. VPN clients connect to the external interface, and I try to ping inside and the demilitarized zone, respectable 172.16.1.0 and 172.16.9.0 hosts. VPN client shows that the two previously mentioned networks such as roads of security, but still not to the ping pong.

  # sh nat

  Manual NAT policies (Section 1)

  1 (inside) to the (whole) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  2 (inside) to the (whole) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  3 (inside) to the (whole) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - 172.16.12.0 obj - one-way 172.16.12.0

  translate_hits = 0, untranslate_hits = 0

  4 (dmz) to (outside) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  5 (dmz) to (outside) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - 172.16.12.0 obj - one-way 172.16.12.0

  translate_hits = 0, untranslate_hits = 0

  Auto NAT policies (Section 2)

  1 (dmz), to the source (external) static obj - 172.16.9.5 interface tcp www www service

  translate_hits = 0, untranslate_hits = 142

  2 (dmz) (outdoor) source static obj - 172.16.9.5 - 01 interface service tcp 3389 3389

  translate_hits = 0, untranslate_hits = 2

  3 (dmz) (outdoor) source static obj - 172.16.9.5 - 02 interface tcp ldap ldap service

  translate_hits = 0, untranslate_hits = 0

  4 (dmz) (outdoor) source static obj interface - 172.16.9.5 - 03 service ftp ftp tcp

  translate_hits = 0, untranslate_hits = 0

  5 (dmz) to (outside) of the source static obj - 172.16.9.5 - 04 interface tcp smtp smtp service

  translate_hits = 0, untranslate_hits = 267

  6 (inside) source static obj - 172.16.9.0 172.16.9.0 (dmz)

  translate_hits = 4070, untranslate_hits = 224

  7 (inside) to (dmz) source static obj - 10.1.0.0 10.1.0.0

  translate_hits = 0, untranslate_hits = 0

  8 (inside) to (dmz) source static obj - 172.16.0.0 172.16.0.0

  translate_hits = 152, untranslate_hits = 4082

  9 (dmz) to dynamic interface of the obj - 172.16.9.0 - 01 source (outdoor)

  translate_hits = 69, untranslate_hits = 0

  10 (inside) to the obj_any interface dynamic source (external)

  translate_hits = 196, untranslate_hits = 32

  I think you must following two NAT config

  NAT (inside, outside) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - 192.168.100.0 obj - 192.168.100.0
  NAT (dmz, external) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - 192.168.100.0 obj - 192.168.100.0

  Please configure them and remove any additional NAT configuration and then try again.

• VPN - PC (vpn client) problem-> router-> (site to site vpn)-> local network

  Hello

  is it possible to install?

  I have a pc and I want to connect to the Remote LAN.

  PC (using vpn client) - vpn (internet)---> ROUTER1 - a vpn (MPLS network)---> ROUTER2---> SERVER site

  How can I connect to a remote server? Is there an easy way?

  I did the configuration of the vpn client (I can connect ROUTER1 and access a LAN via vpn with 192.168.1.x), but I can't connect to the server, even if I set the subnet (192.168.1.x) under the access list of site to site vpn (access list for traffic that must pass between ROUTER1 and ROUTER2).

  Please advise! Thanks in advance.

  Looks like I've not well explained.

  On ROUTER1

  ===================

  1 ACL VNC_acl is used to split tunnel, so you should include IP server_NET it NOT vpn IP pool.

  2 ACL najavorbel is used to set the lan lan traffic between ROUTER1 and ROUTER2, 2 you should inlcude

  IP 192.168.133.0 allow 0.0.0.255 0.0.0.255

  You must change the crypto ROUTER2 ACL of the minor or the najavorbel of the ACL

  The other way to is to the client VPN NAT IP to a local area network lan IP ROUTER1, in this way, you don't need any changes on ROUTER2. But I have to take a look at your configuration to make the suggestion.

• Cisco 2621 to VPN client problem

  If I ping on the client to the network (behind the router), debug displays the client encryption and decryption of the router. The ping will not, because the router is not encrypt and so the customer is not getting anything to decrypt.

  The Setup is a bit different because the default route is within the network, as it is not the regular internet gateway. I have to add routes for pointing the customer who logs on the internet. Also, one machine uses this as a gateway (using a routemap). To troubleshoot, I removed the routemap custom without result. I think to change the default route, but I don't see how this would have on it.

  Any ideas? Am I missing something?

  Cisco 2621 12.2 (15) T running to the latest version of the client.

  username password XXX 7 XXXXXX

  AAA new-model

  !

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  AAA - the id of the joint session

  IP subnet zero

  !

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  Configuration group customer crypto isakmp XXXX

  key XXXXX

  pool ippool

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  !

  interface Loopback1

  192.168.254.1 IP address 255.255.255.0

  !

  interface FastEthernet0/0

  IP address 200.x.x.x 255.255.x.x

  no ip proxy-arp

  NAT outside IP

  automatic duplex

  automatic speed

  clientmap card crypto

  !

  interface FastEthernet0/1

  the IP 10.0.0.1 255.255.255.0

  no ip proxy-arp

  IP nat inside

  route CUSTOMGATE card intellectual property policy

  automatic duplex

  automatic speed

  !

  IP local pool ippool 10.172.10.100 10.172.10.200

  IP nat inside source map route sheep interface FastEthernet0/0 overload

  no ip address of the http server

  no ip http secure server

  IP classless

  IP route 0.0.0.0 0.0.0.0 10.0.0.30

  access-list 100 deny ip 10.0.0.0 0.0.0.255 10.172.10.0 0.0.0.255

  access-list 100 permit ip 10.0.0.0 0.0.0.255 any

  username password XXX 7 XXXXXX

  AAA new-model

  !

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  AAA - the id of the joint session

  IP subnet zero

  !

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  Configuration group customer crypto isakmp XXXX

  key XXXXX

  pool ippool

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  !

  interface Loopback1

  192.168.254.1 IP address 255.255.255.0

  !

  interface FastEthernet0/0

  IP address 200.x.x.x 255.255.x.x

  no ip proxy-arp

  NAT outside IP

  automatic duplex

  automatic speed

  clientmap card crypto

  !

  interface FastEthernet0/1

  the IP 10.0.0.1 255.255.255.0

  no ip proxy-arp

  IP nat inside

  route CUSTOMGATE card intellectual property policy

  automatic duplex

  automatic speed

  !

  IP local pool ippool 10.172.10.100 10.172.10.200

  IP nat inside source map route sheep interface FastEthernet0/0 overload

  no ip address of the http server

  no ip http secure server

  IP classless

  IP route 0.0.0.0 0.0.0.0 10.0.0.30

  IP route 20.x.x.x 255.255.255.255 200.x.x.x (it is here to let him speak to the customer)

  access-list 100 deny ip 10.0.0.0 0.0.0.255 10.172.10.0 0.0.0.255

  access-list 100 permit ip 10.0.0.0 0.0.0.255 any

  access-list 110 deny host ip 10.0.0.73 10.1.0.0 0.0.0255

  access-list 110 permit ip 10.0.0.73 host everything

  !

  CUSTOMGATE allowed 10 route map

  corresponds to the IP 110

  IP 200.x.x.x next value break

  !

  sheep allowed 10 route map

  corresponds to the IP 100

  !

  !

  CUSTOMGATE allowed 10 route map

  corresponds to the IP 110

  IP 200.x.x.x next value break

  !

  sheep allowed 10 route map

  corresponds to the IP 100

  !

  Add at least:

  > Route ip 10.172.10.0 255.255.255.0 200.x.x.x

  to force the traffic for VPN clients on the external interface. also make sure you hav a route for the clients IP address (not the VPN negotiated one) that also indicates the external interface.

  The fact that the router is not encrypt means that it is not even see the responses from the inside, hosts, which indicates that your internal network is not a road to 10.172.10.0 pointing to this router, OR the router receives responses but sends them back out inside interface which will be set by the first route, I mentioned above.

• Problems of transfer of files on the laptop with USB - Satellite Pro L100

  I have a Topfield Freeview box that connects to my Toshiba Satellite Pro L100 via a very short USB cable. The box can read MP3s that I add via the USB connection.

  My previous laptop added to hundreds of songs without any problem at all. However, this new Toshiba there are very particular problems.

  I can send files of the TNT box to the laptop via USB with no problems, but if I try to send files (for example an MP3) Unlike - laptop box - it stutter and often fail. From time to time an entire song (only 4-5 MB) may be transferred without problems, but normally, it will not work. As I said, I can send 100 MB s, the other direction and everything works fine.

  I tried transfer MP3s from my laptop and on the TNT housing with non-Toshiba laptop from a friend today and worked well. This collaboration with knowing I could do the same with my old laptop, suggests that the problem is clearly with the laptop. There must be a reason this notebook can transfer information via USB in a much better than in the other direction.

  Is there anything I can do to upgrade drivers or software to allow my laptop works properly?

  [Edited by: admin]

  I put t know why this happens and I can only suggest.
  For example on my laptop when something be transferred from an external source laptop and another way the software Anti Virus check all files and so it takes much more time.

  I just disabled the anti scan antivirus and firewall and the transfer was going faster.

  Eventually he s has the same problem on your laptop

• I had problems to download some files with ie9, it gets to 99% and I get a partial transfer is defective.

  I noticed that I am not alone, because many questions were asked for some time now on the same subject. I ended up downloading downloads of microsoft ie9, and he moved way diferent to the format of windows update, programs before loading of closing. It did not work so I went back to ie8 and abandoned. I had another go this morning and low and here this worked, I installed a java update and windows update kb2797052 and it still worked.

  What happens here?

  17 2630qm

  8 GB ram

  1 Gb Nvidia graphics

  Toshiba p750

  Windows 7 64 bit

  You can download in "Safe Mode with networking"?

  What if you try your download with any Anti Virus disabled.  There may be another program interfering?

  Startup options (including safe mode)
  http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode

  How to perform a clean boot for a problem in Windows Vista, Windows 7 or Windows 8
  http://support.Microsoft.com/default.aspx/KB/929135

• VPN Client problem

  A remote user on our network has problems with the Cisco VPN. They are using Win XP, Cisco Client 3.5.2 and connect via a router of Compaq Ipaq into a modem cable. When they VPN in our 3000 VPN concentrator works very well. When they try to VPN in the PIX on our network, it indicates that the client is no longer. If they use a Microsoft VPN to connect to the network with the 3000 (we run both MS and Cisco VPN) with it set to use the remote control, the default gateway, the Cisco VPN will connect to the PIX, see the network behind PIX, ping stuff behind the PIX, but not map a drive. The remote user can ping the PIX of their unVPNed in the remote location. No other user is a problem connecting to the PIX (except those with the bad remote access or broadband satellite which cannot VPN into anything anyway). We have even a few AOLer connect to it. Help me please.

  If the compaq ipaq router makes a PAT, that might be the problem. PIX is unable to manage the ipsec clients who crossed pat. The vpn3000 has some mechanism to deal with this. PPTP is different to ipsec.

  You must ensure that the ipsec client has its own public routable ip address.

  Kind regards

• HP 8610: problem printing of PDF files with iMac

  I have a HP 8610 all-in-One powered by an iMac.

  I have a problem with printing of PDF files.

  When I print, the page moves approximately 1.5 inches down and doesnot print page as seen on the screen.

  I checked with Apple and you s not a problem with the computer.  They say that there must be a parameter that must be corrected with the printer.

  If you encounter the problem with PDF files and only on the Mac, the best solution may be to download and run a different PDF Viewer that allows you to open the file and print instead. Adobe, Foxit, and Nitro are a few free PDF viewers with Mac support.

  Please let me know if you are able to print your PDF documents using one of these programs instead, or if you have any other questions. If not, have a great day!

• I have problems to open bmp files with paint.

  It worked fine until a week ago, but all of a sudden I get "Paint cannot read this file. is not a valid bitmap file, or its format is not currently supported. I use it to change the drawings to PDF which I did over the years (just adding the welding symbols). And Yes, actually saving the file in the paint as a BMP file before I try to open it, I can't open it in PDF format. I open the PDF file and copy the image to paint to edit then save as a .bmp. When I try to open it again, I get the error. Also I tried to save the file in different formats (ie. jpeg, png, etc) and trying to open but I get the same error. Please any help would be appreciated, because now I have been their opening with PaintXP that works but I can't zoom in as I can in windows 7.

  It's a stumpper for sure. I know this isn't associated file, that I have already dealt with that. I'll just have to find a similar free commodity with basic editing even. and just reinstall windows when I get home from work. Thank you much for the help :)

• Problem opening of PDF files with adobe

  I can't get Adobe to open my pdf files. No internet or desktop.

  I download fine. I have installed and reinstalled several times.

  If I try to open it, it looks like it opens but closes immediately. I tried to open adobe, but nothing. A gray screen and that's it. I can't access the help button

  A few things to try...

  • Update to version 11.0.3 Reader
  • Using Windows Explorer navigate to C:\Program Files (x 86) \Adobe\Reader 11.0\Reader, and then double-click Eula.exe and accept the license agreement
  • You can open Adobe Reader by itself?  If so, try to disable the Protected Mode [Edit |] Preferences | (Improved) security].
  • It might even be a malware problem; See http://helpx.adobe.com/acrobat/kb/reader-core-dll-error.html