VPN connectivity to a server in offline mode.

Similar Questions

• problem of bluetooth of Windows 8. Phone paired but unable to connect, says Windows phone in offline mode

  Problem of bluetooth of Windows 8. Phone paired but unable to connect, says Windows phone in offline mode

  Somasundaram Mohammed. Thank you for your help and maybe you will pass on the solution to all those in need. All that is necessary is to download Bluetooth Stack Toshiba 9.10 and run it. However be careful because version 9.0 of battery is not compatible. I have now my two Android phones connected.

  Thanks again

  John harney

• VPN connection but smb://server does not exist

  Hello guys,.

  I'm having a problem with my Mac.

  I have configured a VPN server (work) and connectd normally.

  

  However, when I look at the list servers, in search, the server do not appear:

  

  And when I try to connect using the finder (go > connect to server) the following message

  

  Could you help me?

  BdW

  TKS

  Hello does not work through a VPN tunnel. You identify the server by its numeric IP address or a FQDN name.

• change module cause some ports of a server in offline mode

  Hello

  I have a server with 4 ethernet ports, 1 G, they are glued together, two of them was pluged in the cat6500 WS - X 6724-TX module. now, we have moved the two ports to replace WS - X 6748-GE-TX module.

  one of two ports are not online.

  cat6500 #sh int g10/2nd round

  interface GigabitEthernet10/2

  Moved server description

  switchport

  switchport access vlan 102

  switchport mode access

  No cdp enable

  spanning tree portfast edge

  end

  I also ran sh run all, and I found that there is that a stop was on the race any:

  cat6500 # sh run all | interface b GigabitEthernet10/2

  interface GigabitEthernet10/2

  Moved server description

  switchport

  switchport access vlan 102

  switchport mode access

  Shutdown---> what a surprise!

  No mab

  SNMP trap-the link status

  No cdp enable

  spanning tree portfast edge

  !

  I checked on the server side, the binding configuration is even not changed.

  Please advice, what possible reason replace module will cause link offline? Why give "sh run all" stop is the port? anywhere, I can solve this problem?

  Any comments will be appreciated

  Thanks in advance

  Julxu

  Hello

  So, what happens if you do a "no HS" under the interface?

  In addition, you can post 'sh ip int bri gi10/2?

  What IOS version do you use?

  SH ver | bin Inc.

  HTH

• Random L2TP connection problem for server 2008 R2

  I had a strange problem with a L2TP VPN connection to a Server 2008 R2.  Some systems on some networks can not connect successfully.  Nothing is recorded on the Server 2008 R2 box.  I see traffic from our firewall to the box, but it does not complete the configuration of the tunnel.

  For example, I have a laptop that I can't connect from my home, but can from other locations.  I have a second laptop that connect to my house without any problem.  I saw this question on at least 5 computers.  Until I can fix this, I have to keep my Server 2003 running VPN so that users have a back fall VPN to connect to.

  Error 789: The L2TP connection attempt failed because the security layer met a processing error during initial negotiations with the remote computer

  Hi Mike,.

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  Browse this link which has useful information about the error message that you receive.

  http://blogs.technet.com/b/rrasblog/archive/2009/08/12/troubleshooting-common-VPN-related-errors.aspx

  Hope this could help you.

• I'm having a problem when I try to establish a VPN connection

  I have a problem when I try to establish a VPN connection between a remote computer and my desktop computer that we use as a file server in our network of workplaces. It has a static IP address. The VPN connection was working until the person on the other side you have forgotten the password. We decided to set up a new connection with the new user name and password. The remote computer could not establish a VPN connection with the server, but when the person on the other side tried to open the files, she received a message indicating there is no permission to do so. I can't understand how to give the person permission to open folders. Can anyone help?

  Hello

  Thanks for posting in the Microsoft Community.

  The question you posted would be better suited in the TechNet community.
  http://social.technet.Microsoft.com/forums/en/w7itprogeneral/threads

  I hope this helps!

• established - VPN connection, but cannot connect to the server?

  vpn connection AnyConnect is implemented - but cannot connect to the server? The server IP is 192.168.0.4

  Thank you

  ASA Version 8.2 (1)

  !

  hostname ciscoasa5505

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.0.3 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP 208.0.0.162 255.255.255.248

  !

  interface Vlan5

  Shutdown

  prior to interface Vlan1

  nameif dmz

  security-level 50

  IP address dhcp setroute

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  passive FTP mode

  clock timezone PST - 8

  clock summer-time recurring PDT

  DNS lookup field inside

  DNS server-group DefaultDNS

  192.168.0.4 server name

  Server name 208.0.0.11

  permit same-security-traffic intra-interface

  object-group Protocol TCPUDP

  object-protocol udp

  object-tcp protocol

  object-group service TS-780-tcp - udp

  port-object eq 780

  object-group service Graphon tcp - udp

  port-object eq 491

  Allworx-2088 udp service object-group

  port-object eq 2088

  object-group service allworx-15000 udp

  15000 15511 object-port Beach

  object-group service udp allworx-2088

  port-object eq 2088

  object-group service allworx-5060 udp

  port-object eq sip

  object-group service allworx-8081 tcp

  EQ port 8081 object

  object-group service web-allworx tcp

  EQ object of port 8080

  allworx udp service object-group

  16001 16010 object-port Beach

  object-group service allworx-udp

  object-port range 16384-16393

  object-group service remote tcp - udp

  port-object eq 779

  object-group service billing1 tcp - udp

  EQ object of port 8080

  object-group service billing-1521 tcp - udp

  port-object eq 1521

  object-group service billing-6233 tcp - udp

  6233 6234 object-port Beach

  object-group service billing2-3389 tcp - udp

  EQ port 3389 object

  object-group service olivia-3389 tcp - udp

  EQ port 3389 object

  object-group service olivia-777-tcp - udp

  port-object eq 777

  netgroup group of objects

  network-object host 192.168.0.15

  network-object host 192.168.0.4

  object-group service allworx1 tcp - udp

  8080 description

  EQ object of port 8080

  allworx_15000 udp service object-group

  15000 15511 object-port Beach

  allworx_16384 udp service object-group

  object-port range 16384-16393

  DM_INLINE_UDP_1 udp service object-group

  purpose of group allworx_16384

  object-port range 16384 16403

  object-group service allworx-5061 udp

  range of object-port 5061 5062

  object-group service ananit tcp - udp

  port-object eq 880

  outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing-6233

  outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing-1521

  outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing2-3389

  outside_access_in list extended access permit tcp any host 208.0.0.164 eq https

  outside_access_in list extended access permit tcp any host 208.0.0.164 eq www

  outside_access_in list extended access permit tcp any host 208.0.0.164 eq ftp

  outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing1

  outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 EQ field

  outside_access_in list extended access permit tcp any host 208.0.0.162 eq www

  outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 remote object-group

  outside_access_in list extended access permit tcp any host 208.0.0.162 eq smtp

  outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 object-group olivia-777

  outside_access_in list extended access permit udp any host 208.0.0.162 - group Allworx-2088 idle object

  outside_access_in list extended access permit udp any host 208.0.0.162 object-group inactive allworx-5060

  outside_access_in list extended access permit tcp any host 208.0.0.162 object-group web-allworx inactive

  outside_access_in list extended access permit tcp any host 208.0.0.162 object-group inactive allworx-8081

  outside_access_in list extended access permit udp any host 208.0.0.162 object-group inactive allworx-15000

  outside_access_in list extended access permit udp any host 208.0.0.162 DM_INLINE_UDP_1 idle object-group

  outside_access_in list extended access permit udp any host 208.0.0.162 object-group inactive allworx-5061

  outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 inactive ananit object-group

  outside_access_in list extended access deny ip host 151.1.68.194 208.0.0.164

  permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 172.16.0.0 255.255.0.0

  permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.1.0 255.255.255.0

  permit access ip 192.168.0.0 scope list outside_20_cryptomap 255.255.255.0 172.16.0.0 255.255.0.0

  Ping list extended access permit icmp any any echo response

  inside_access_in of access allowed any ip an extended list

  permit access ip 192.168.0.0 scope list outside_cryptomap 255.255.255.0 192.168.1.0 255.255.255.0

  access-list 1 standard allow 192.168.0.0 255.255.255.0

  pager lines 24

  Enable logging

  logging buffered stored notifications

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  MTU 1500 dmz

  IP local pool 192.168.100.30 - 192.168.100.60 mask 255.255.255.0 remote_pool

  192.168.0.20 mask - distance local pool 255.255.255.0 IP 192.168.0.50

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  NAT (outside) 1 192.168.0.0 255.255.255.0

  alias (inside) 192.168.0.4 99.63.129.65 255.255.255.255

  public static tcp (indoor, outdoor) interface 192.168.0.4 smtp smtp netmask 255.255.255.255

  public static tcp (indoor, outdoor) interface field 192.168.0.4 netmask 255.255.255.255 area

  public static tcp (indoor, outdoor) interface 192.168.0.4 www www netmask 255.255.255.255

  public static tcp (indoor, outdoor) interface 777 192.168.0.15 777 netmask 255.255.255.255

  public static tcp (indoor, outdoor) interface 779 192.168.0.4 779 netmask 255.255.255.255

  public static (inside, outside) udp interface field 192.168.0.4 netmask 255.255.255.255 area

  public static tcp (indoor, outdoor) interface 880 192.168.0.16 880 netmask 255.255.255.255

  static (inside, outside) 208.0.0.164 tcp 3389 192.168.0.185 3389 netmask 255.255.255.255

  inside_access_in access to the interface inside group

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 208.0.0.161 1

  Route inside 192.168.50.0 255.255.255.0 192.168.0.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  Enable http server

  http 192.168.0.0 255.255.255.0 inside

  http 192.168.0.3 255.255.255.255 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Sysopt noproxyarp inside

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  card crypto outside_map 1 match address outside_cryptomap

  card crypto outside_map 1 set pfs

  peer set card crypto outside_map 1 108.0.0.97

  card crypto outside_map 1 set of transformation-ESP-3DES-SHA

  card crypto outside_map 20 match address outside_20_cryptomap

  card crypto outside_map 20 set pfs

  peer set card crypto outside_map 20 69.0.0.54

  outside_map crypto 20 card value transform-set ESP-3DES-SHA

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life no

  crypto ISAKMP policy 30

  preshared authentication

  3des encryption

  sha hash

  Group 1

  life no

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  identifying client DHCP-client interface dmz

  dhcpd outside auto_config

  !

  dhcpd address 192.168.0.20 - 192.168.0.50 inside

  dhcpd dns 192.168.0.4 208.0.0.11 interface inside

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow outside

  SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image

  enable SVC

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  internal group anyconnect strategy

  attributes of the strategy group anyconnect

  VPN-tunnel-Protocol svc webvpn

  WebVPN

  list of URLS no

  SVC request enable

  encrypted olivia Zta1M8bCsJst9NAs password username

  username of graciela CdnZ0hm9o72q6Ddj encrypted password

  tunnel-group 69.0.0.54 type ipsec-l2l

  IPSec-attributes tunnel-group 69.0.0.54

  pre-shared-key *.

  tunnel-group 108.0.0.97 type ipsec-l2l

  IPSec-attributes tunnel-group 108.0.0.97

  pre-shared-key *.

  tunnel-group anyconnect type remote access

  tunnel-group anyconnect General attributes

  remote address pool

  strategy-group-by default anyconnect

  tunnel-group anyconnect webvpn-attributes

  Group-alias anyconnect enable

  !

  Global class-card class

  match default-inspection-traffic

  !

  !

  World-Policy policy-map

  Global category

  inspect the icmp

  !

  service-policy-international policy global

  : end

  ASDM location 208.0.0.164 255.255.255.255 inside

  ASDM location 192.168.0.15 255.255.255.255 inside

  ASDM location 192.168.50.0 255.255.255.0 inside

  ASDM location 192.168.1.0 255.255.255.0 inside

  don't allow no asdm history

  Right now your nat 0 (NAT exemption) follows the access list:

  permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 172.16.0.0 255.255.0.0

  permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.1.0 255.255.255.0

  Traffic back from your server to 192.168.0.4 in the pool of VPN (192.168.0.20 - 50) not correspond to this access list and thus be NATted. The TCP connection will not develop due to the failure of the Reverse Path Forwarding (RPF) - traffic is asymmetric NATted.

  Then try to add an entry to the list of access as:

  permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.0.0 255.255.255.0

  It's a bit paradoxical but necessary that your VPN pool is cut out in your interior space network. You could also do like André offers below and use a separate network, but you would still have to add an access list entry to exempt outgoing NAT traffic.

• How to go from "offline" Mode when you use Firefox on an android device that is connected to the internet through Bluetooth.

  I have been using my tf300. Whenever I try to open Firefox on the Tablet while using a Bluetooth connection, the only screen that Firefox opens is a generic screen displaying 'Offline Mode '. Is there a way to switch to online mode or I am able to use the browser on a wireless signal?

  Could you clarify - are other applications can connect to the internet when you are logged in this mode?

• How to connect to the server from VPN Windows Sever?

  Hey guys, I recently created my own VPN server to connect to my home network using Windows Server 2003. I know I probably still need to do this if I don't know what I have to do, but how to connect to the server, or at least set it up in order to be logged in? I think I got the computers communicating with each other, but I think that I am running into errors of authentication. Could someone point me in the right direction with regard to what I have to do what I already have Setup? Thanks in advance.

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• How can I connect to my server (which runs on windows server 2008 rc2) via IP REAL using rdp, while the VPN connection is active?

  Hello

  How can I connect to my sServer (which runs on windows server 2008 rc2) via IP REAL using rdp, while the VPN connection is active?
  

  Hello Marie Smith.

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the link below.

  http://social.technet.Microsoft.com/forums/en-us/winservergen/threads/

  Hope this information helps.

• Implementation of VPN for INCOMING connections to my server running Windows 7

  I need to set up a private network virtual SERVER on my server on Windows 7 and can't find the information I need to do this. Can someone explain what I need to do. I have a fixed IP address for my cable modem.

  I need to set up a private network virtual SERVER on my server on Windows 7 and can't find the information I need to do this. Can someone explain what I need to do. I have a fixed IP address for my cable modem.

  See this article for help...

  http://Windows.Microsoft.com/en-us/Windows7/set-up-an-incoming-VPN-or-dial-up-connection

  Remember that for a PPTP VPN server you must forward/open the TCP 1723 Port through a firewall or a router to the PC server is behind. You must also make sure that the firewall or the router will pass traffic GRE protocol 47 . This is sometimes called PPTP Pass Through or VPN Pass Through the firewall or the router. Windows Firewall automatically communicates the GRE protocol traffic if you make an Exception for the Port TCP 1723.

  You can test it by running the test detailed in sections PPTP Ping and VPN traffic in this Cable Guy article.

  http://TechNet.Microsoft.com/en-us/library/bb877965.aspx

  You can download the tools, pptpsrv.exe and pptpclnt.exe to Microsoft or if you have an XP SP2 CD. To extract the programs on a PC Windows 7 open the CD and select open folder to view files in the AutoPlay window.

  Extra help...

  http://Windows.Microsoft.com/en-us/Windows7/why-am-I-having-problems-with-my-VPN-connection

  MS - MVP Windows Desktop Experience, "when everything has failed, read the operating instructions.

• Impossible to establish a VPN connection with a router configured as a Cisco server using client VPN 5.0.00.0340

  Hei guys,.

  Please help me on this one because I'm stuck enough on her...

  I am trying to connect to a Cisco 3700 router configured as a VPN server by using a VPN client and the VPN connection does not settle.

  This is an extract from the log:

  130 12:48:30.585 07/01/11 Sev = Info/5 IKE / 0 x 63000001
  Peer supports XAUTH
  131 12:48:30.585 07/01/11 Sev = WARNING/3 IKE/0xE3000057
  The HASH payload received cannot be verified
  132 12:48:30.600 07/01/11 Sev = WARNING/2 IKE/0xE300007E
  Failed the hash check... may be configured with password invalid group.
  133 12:48:30.600 07/01/11 Sev = WARNING/2 IKE/0xE300009B
  Impossible to authenticate peers (Navigator: 904)
  134 12:48:30.600 07/01/11 Sev = Info/4 IKE / 0 x 63000013
  SEND to > ISAKMP OAK INFO (NOTIFY: INVALID_HASH_INFO) for 200.100.50.173

  I enclose the whole journal extract... The message "BOLD" is quite obvious, you mean, but I'm 100% sure, in the login entry, I typed correctly the group password: pass

  My topology is very basic, as I am setting this up only to get a clue of the operation of the Cisco VPN. It is built in GNS3:
  -2 3700 routers: one of them holds the configuration of the VPN server and the other would be the ISP through which the remote worker would try to establish a VPN connection. I am also attaching the configuration file for the router configured as a VPN router.

  Behind the second router there is a virtual XP machine on which I have installed VPN client...

  My connection entry in the customer is to have the following parameters:
  Host: 200.100.50.173 , //which is the IP address of the VPNServer
  Authentication-> authentication-> name group: grup1 password: pass / / I'm quite positive that I typed the correct password... even if the log messages are linked to a misidentification.

  I use public addresses only, because I noticed there is a question about behind the NAT VPN connections and is not not very familiar to the NAT.

  Another aspect which can be of any importance is that "allow Tunneling of Transport" in the tab Transport to the input connection is disabled

  and the VPNServer router logs the following error message when you try to establish the connection:

  * 01:08:47.147 Mar 1: % CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE 200.100.50.34 package was not encrypted and it should have been.
  * 01:08:47.151 Mar 1: % CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE 200.100.50.34 package was not encrypted and it should have been.
  

  You have no idea why I can't connect? Y at - it something wrong with my configuration of VPN server... or with the connection entry in the VPN client?

  Thank you

  Iulia

  Depending on the configuration of the router, the group name is grup1 and the password is baby.

  You also lack the ipsec processing game that you would need to apply to the dynamic map.

  Here is an example configuration for your reference:

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080235197.shtml

  Hope that helps.

• Security problems of Windows 7 connecting to the VPN to a ras server

  We run a domain for most of our users - but not all - due to the merger of companies

  We use vpn connections from Windows at the standard address to access remotely via a no domain Server 2003 running RSA

  Windows name nigel.hunter@domain-name

  VPN username nhunter

  When runnin Windows xp users can get access to the files on the servers

  When you run Windows 7, they can

  have found that the system windows 7 are passing the VPN user name and credentials instead of the credentials of domain

  This does not prevent access

  Anyone know how I can get to pass the credentials of the doamin during access to the VPN servers

  Thanks in advanced for any help

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  TechNet Forum

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  Hope this information helps.

• Problem connecting to the server, error connection server and printer offline. I have a HP photosmart printer and Windows 7?

  My printer is not printing. It say problem connecting to the server, connection error server and printer offline. I have a HP photosmart printer and windows 7.

  You have McAfee? McAfee has been updated at the same time as the last batch of updates from Windows 7 and it seems to be the cause of this problem for most, if not all, users.

  See the communication from this "criticism" - McAfee

  Some customers may experience a loss of network connectivity and/or errors in McAfee Security Center after a recent update

  You should make the fix McAfee, if necessary. There are corresponding communications for their enterprise products.

  I got McAfee, but the connection has started working again on its own so I thought I was clear of problems. However, when I checked it says he was doing routine checks the updates in vain when I told it to do a manually. So stick with McAfee you don't follow their procedure of fix would have upgraded my PC at risk by not updated and, like other McAfee ads have since explained, the application did not refer to its database of threats correctly [and this could explain part of the variability of the symptoms of failure but all involved loss of internet connection]. Actually, I removed McAfee then installed Microsoft Security Essentials rather & my answer IE is faster I knew it [even though I had the Add-ons McAfee disabled for centuries].

  I had to run the removal of McAfee Development tool a few times before and it caused a problem with the license if the PC was not connected to the internet during the abduction. Due cat of McAfee support reset their files in order to allow the relocation-reactivation. Here is their link cat - McAfee - media contains the link to the cat

• DHCP server on a VM guest that is connected to a router (in AP mode) works on the host Linux (Fedora), but not on the host Windows (XP)

  I'm in dual boot Fedora and Windows XP, and configure a server vmware 2.0.0 122956 on both.

  Here is my config:

  Internet - Modem - vm_gw - vmnet1 (host) - vm_dhcp - router Wireless ADSL - computers laptops

  There are two physical network adapters on my host.  On the virtual machine that connects to the internet (vm_gw), I have one of the network adapters physical bridge (as vmnet0) to dial the ADSL modem and set up a network of hostonly (vmnet1) share the internet connection of the VM on the host and other virtual (vm_dhcp) computer.  On the virtual machine which also shares the internet connection to a wireless (vm_dhcp), I fill the other physical network (like vmnet2) adapters to connect to a router (in AP mode) and have a configuration of DHCP server on it and set up a hostonly (vmnet1) network to get its internet connection of vm_gw.

  I installed proper routing on my host computer and two virtual machines and this config works very well on my Fedora host.  However, the DHCP installation part does not work on my Windows XP host computer.

  The difference between my host Fedora and XP is on Fedora host, can I have two network adapters physical activated with a config 'empty' (to use DHCP or static) as in:

  DEVICE = eth0

  HWADDR = 00:11:22:33:44:55

  ONBOOT = yes

  TYPE = Ethernet

  and

  DEVICE = eth1

  HWADDR = 55:44:33:22:11:00

  ONBOOT = yes

  TYPE = Ethernet

  And there is no conflict on the physical network adapters between the host and the virtual machines.

  However, on XP host, I HAVE to configure the network adapters physical to use DHCP or static.

  If I place the physical network adapter (on the XP host) who will fill to vm_dhcp using DHCP, it will get an IP address from the wireless router and the DHCP server on vm_dhcp doesn't seem to be able to 'find' the wireless router and assign an IP address that him.

  Then I tried to configure the physical network card to use the static IP address (and assign it a fictitious IP address e.g. 192.168.123.1/255.255.255.0) to see if it would work, but it does not work either.

  Then I also tried to "simulate" the 'empty' network on Fedora config using regedit and delete (192.168.123.1/255.255.255.0) IP address on the network config and it does not work.

  Well, I'm out of ideas and I came here as a last resort.  Any suggestion/discussion is welcome.

  Thanks for reading.

  WLPL

  Simple question, I know, but is the Windows XP firewall is enabled?