VPN module?

Similar Questions

• EZVPN 2811 router VPN module

  Hi all

  I have a spare 2811 router that would like to use for the temporary easy VPN server.

  the router IOS is already updated security advance 15.0 K9.

  My question is the AIM - VPN a real map/module on the motherboard of the router or just pop up once the router has been upgraded to IOS security?

  SH ve | I have IOS
  Cisco IOS software, 2800 Software (C2800NM-ADVSECURITYK9-M), Version 15.0 (1) M8, RELEASE SOFTWARE (fc1)

  #sh inv
  NAME: "2811 chassis', DESCR:"2811 chassis.
  PID: CISCO2811, VID: V02, SN: FTX0911Cxxx

  NAME: ' PVDMII DSP SIMM with a DSP on the Slot 0 SubSlot 4 ', DESCR: 'PVDMII DSP SIMM with a DSP.
  PID: PVDM2-16, VID: V01, SN: FOC13071xx

  NAME: "virtual private network (VPN) on the Slot Module 0 ', DESCR: 'encryption PURPOSE Element '.
  PID: AIM-VPN/EPII-PLUS, VID: v01, SN: FOC09072xx

  You have now two VPN modules in your router:

  1. The module for basic needs
  2. The module see you in "inventory to see the" which is placed in the OBJECTIVE of on-board connector. This module has a flow more and a greater number of tunnel and will be used by default.

  There are many examples of EzVPN configuration guide:

  http://www.Cisco.com/c/en/us/TD/docs/iOS-XML/iOS/sec_conn_esyvpn/configuration/15-Mt/sec-easy-VPN-15-Mt-book/sec-easy-VPN-Srvr.html

  If it is more then a temporary solution, I would also consider using an ASA to remote access VPN. EzVPN is more or less obsolete, and the ASA has many more features with the AnyConnect client. On the router, you can also configure remote access for AnyConnect, but it is much more complicated.

• C1841 without the BUILD - IN Module, Bill VPN is a VPN MODULE?

  Hello

  Yesterday, that I just got a new router found on eBay.

  When I boot it I see 2 FastEthernet Interfaces (this is normal and I see them) BUT it also shows me 1 Module of virtual private network (VPN).

  Before I open this new router I try something like:

  Material SH

  SH crypto multicylindres

  HS cry engine Accelerator stat

  Here below you have the results:

  I opened the ROUTER and I see:

  NO ADDITIONAL MEMORY

  NO VPN MODULE

  Did you do something with a built-in CISCO VPN module

  Thanks in advance for your help

  Best regards

  Didier

  Router hardware #sh

  Cisco IOS Software, 1841 (C1841-ADVSECURITYK9-M), Version 12.4 (24) T1, VERSION of the SOFTWARE (fc3)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 1986-2009 by Cisco Systems, Inc.

  Updated Saturday 19 June 09 14:00 by prod_rel_team

  ROM: System Bootstrap, Version 12.4 (13r) T, RELEASE SOFTWARE (fc1)

  The availability of router is 9 hours, 47 minutes

  System to regain the power ROM

  System image file is "flash: c1841-advsecurityk9 - mz.124 - 24.T1.bin".

  This product contains cryptographic features and is under the United States

  States and local laws governing the import, export, transfer and

  use. Delivery of Cisco cryptographic products does not imply

  third party approval to import, export, distribute or use encryption.

  Importers, exporters, distributors and users are responsible for

  compliance with U.S. laws and local countries. By using this product you

  agree to comply with the regulations and laws in force. If you are unable

  to satisfy the United States and local laws, return the product.

  A summary of U.S. laws governing Cisco cryptographic products to:

  http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html

  If you need assistance please contact us by mail at

  [email protected] / * /.

  Cisco 1841 (revision 7.0) with 118784K / 12288K bytes of memory.

  Card processor ID FCZ1217905C

  2 FastEthernet interfaces

  1 module of virtual private network (VPN)

  Configuration of DRAM is 64 bits wide with disabled parity.

  191K bytes of NVRAM memory.

  250880K bytes of ATA CompactFlash (read/write)

  Configuration register is 0 x 3922

  Router #.

  Router #sh crypto multicylindres

  crypto engine name: virtual private network (VPN) Module

  crypto engine type: hardware

  Status: enabled

  Geographical area: 0 on board

  Name of product: edge-VPN

  HW Version: 1.0

  Compression: Yes

  A: Yes

  3 a: Yes

  AES - CBC: Yes (128,192,256)

  AES CNTR: No.

  Maximum length of the buffer: 4096

  Index maximum DH: 0000

  Maximum ITS index: 0000

  Maximum fluidity index: 0300

  The maximum size of the RSA key: 0000

  version of crypto lib: 20.0.0

  engine crypto in the slot: 0

  platform: hardware VPN Accelerator

  version of crypto lib: 20.0.0

  Router #sh cry engine Accelerator stat

  Device: FPGA

  Location: on board: 0

  : Statistics for device encryption since the last clear

  counters 35534 seconds ago

  68607 68607 out packages packages

  49819692 bytes in 50341181 bytes on

  1 paks/s to 1 output paks/s

  11 Kbps in 11 Kbits/sec out

  29298 decrypted packets 39309 encrypted packets

  4074464 bytes before decipher 45745228 encrypted bytes

  2537109 bytes decrypted 47804072 bytes after encrypt

  0 0 packets compressed decompressed packets

  0 bytes before Dang 0 bytes before comp

  0 bytes after Dang 0 bytes after model

  0 packets bypass decompression 0 by-pass compressor packages

  Derivation of 0 bytes 0 bytes decompression work around compressi

  0 packets not unzip 0 uncompressed packages

  0 bytes not decompressed 0 bytes not compressed

  1.0:1 overall compression ratio 1.0:1

  last 5 minutes:

  11 packages into 11 out packets

  0 paks/sec output paks/s 0

  32-bit/s at 28 bits/sec out

  496 bytes decrypted 329 bytes encrypted

  13 decrypted Kbps 8 Kbps encrypted

  1.0:1 overall compression ratio 1.0:1

  FPGA:

  DS: 0x6538DE50 idb:0x6538CD08

  Statistics for virtual private network (VPN) Module:

  68607 68607 out packages packages

  1 paks/s to 1 output paks/s

  11 Kbps in 11 Kbits/sec out

  29298 decrypted packets 39309 encrypted packets

  package overruns: 0 packets output dropped: 0

  tx_hi_drops: 0 fw_failure: 0

  invalid_sa: 0 invalid_flow: 0

  null_ip_error: 0 pad_size_error: 0 out_bound_dh_acc: 0

  esp_auth_fail: 0 ah_auth_failure: 0 crypto_pad_error: 0

  ah_prot_absent: 0 ah_seq_failure: 0 ah_spi_failure: 0

  esp_prot_absent:0 esp_seq_fail: 0 esp_spi_failure: 0

  obound_sa_acc: 0 invalid_sa: 0 out_bound_sa_flow: 0

  invalid_dh: 0 bad_keygroup: 0 out_of_memory: 0

  no_sh_secret: 0 no_skeys: 0 invalid_cmd: 0

  pak_too_big: 0

  tx_lo_queue_size_max 0 cmd_unimplemented: 0

  flow_cfg_mismatch 0 flow_ip_add_mismatch: 0

  unknown_protocol 0 bad_particle_align: 0

  35535 seconds since the last cleaning counters

  Interruptions: Notification = 54892

  Router #.

  vpn module on board can certainly improve VPN performance comparing to pure VPN software, but is not as good as the AIM - VPN module.

  So, this will depend on your vpn traffic load, etc...

• 2620xm router VPN module

  I have a router 2620xm 12.4 (25) with the Module Module encryption VPN DES_3DES_AES (AIM-VPN_EPII, VPN_HPII-AIM, AIM-VPN_BPII)

  I'm under Softether VPN server using IPSEC will the customers enjoy the module?

  David,

  These devices have been end of life for a while. Just in case you missed it:

  http://www.Cisco.com/en/us/prod/collateral/routers/ps259/prod_end-of-life_notice0900aecd804446da.html

  If I remember the old objectives, yes its IPsec will be used for all flows. You can confirm by:

  show crypto engine configuration
  
  

  Which should display what your engine is capable of. I could be on the account of this device being dead for a while

• Please ME TELL WHAT Cisco VPN internal Service Module

  I do not know what is the internal service of cisco vpn module, how it words, and where we can use it.

  Hello

  Cisco internal VPN Service Module is a Cisco ISR G2.

  I would say that the main goal is the ability to offload the encryption to a dedicated service module. Dedicated encryption protects performance when CPU utilization for other services.

  You can find the data sheet here:

  http://www.Cisco.com/en/us/prod/collateral/modules/ps2706/ps12202/data_sheet_c78-682436.html

  Also on the card you will find what routers support this module.

  Please evaluate the useful messages

  Best regards

  Eugene

• Hide the AnyConnect VPN AnyConnect GUI Module

  Dear team

  We are wired deployment 802. 1 x with Posture and that NAM is sufficient for us.

  but when installing AnyConnect vpn module must be installed and cannot be avoided, so VPN tab is also visible in the GUI AnyConnect interface,

  I need to disable the VPN tab from the interface chart anyconnect, because it is not used and confusing for end users.

  We have anyconnect-win-4.1.00028-pre-deploy-k9.

  We have a manual installation of AnyConnect on PC or Client Provisioning, we don't use MSI

  Please suggest 'VPN profile' to end users, which will hide this vpn module.

  Thank you

  Ahad

  Your situation is highlighted in the AnyConnect Administrator's Guide as well:

  When you configure the object Configuration AnyConnect to ISE, unchecking the VPN module under the AnyConnect Module selection does not disable VPN on the customer deployed/put in service. You must set VPNDisable_ServiceProfile.xml to disable the VPN AnyConnect GUI tile. VPNDisable_ServiceProfile.xml is on EAC with other files AnyConnect.

  The xml file, you need should be on the AnyConnect downloads page, but is not. There's a BugID noting that (CSCus26084). Work around the BugID does not work for me, but it could for you.

  The profile CAN be found in the msi file - if you open with 7-zip, you can find the file. She is short, so I'll just paste here:

       true  

• Is AnyConnect module - mandatory to install/configure all three VPN, NAM & Posture module ISE 1.3 for evaluation of posture

  Hi Experts,

  I installing Anyconnect point doubt:

  We want to go for web-deployment of head of network device that is ISE for the assessment of posture, however I came across the document where its mentioned the installation with the three modules:

  (1) VPN

  (2) NAM

  (3) module posture

  I am only concerned to posture to check on enterprise wireless users until I have to configure all of the modules in customer provisioning?

  There is no existing with Anyconnect client configuration. No ASA as n for my case. I have WLC acting as n.

  so after that customer gets auth 802.1 x, customer must redirect to posture help control Anyconnect. and its new deployment where the customer is not having this agent software.

  If please guide me with the right direction for Anyconnect deployment for single control of posture and how customers can get this downloaded automatically agent is my main concern.

  For assessment of posture, just deploy the "Module of Posture". The "NAM" module is used only when you want to replace the native Windows supplicant. The "VPN" module is used for anyconnect VPN.

  The posture can be hosted in the ISE and be put into service at the endpoints via a Client Provisioning rule. However, users must have the appropriate privilege to perform the installation of the package. In many organizations, users have NO such privileges. If this is your case, so you must deploy the Posture Module via GPO/System Center or another equivalent system.

  I hope this helps!

  Thank you for evaluating useful messages!

• Throuput VPN on a 2651XM router

  Where can I find this info?

  Also, I got the used router (for nearly nothing $) but I know it's a value of some $$$. Where can I find out what model it is exactly? 'show version' doesn't show much.

  Oh sorry, pasted the link partner. This link doesn't seem to be available on a non-partner unfortunately link, so here's a copy of the relevant pieces of her:

  --------------------------------------

  AIM-VPN/BPII, is only supported in the Cisco 2600XMs. It has support for DES/3DES and AES (optimized for the AES128 only) as well as layer 3 Compression (IPPCP). This module requires ZJ Cisco IOS version 12.2 (15) and later versions.

  AIM-VPN/BPII - MORE is only supported in the Cisco 2600XMs. AIM-VPN/EPII-PLUS is supported in the 2691 and 3725 only. The BPII-PLUS and EPII-PLUS supports DES/3DES and are optimized for all key AES (AES128, AES192 and AES256) with Layer 3 Compression (IPPCP). These modules are supported in 12.3 (5 c), 12.3 (6) and later for the releases of the pipe major and 12.3 (7) T and later for releases of T.

  Q. What is the function executes the VPN Module?

  A. the Module VPN of Cisco 1700, 2600, 3600, and 3700 Series optimizes the platform for the IPSec VPN. Module accelerates not only the triple data standard (3DES) encryption and data (a) standard encryption, advanced encryption standard (AES) algorithms used in IPSec, but it handles many other tasks related to IPSec: hash, key exchange and storage of security associations. In doing so, the VPN module releases the Cisco 1700 series processor, 2600, 3600, and 3700 to run another router, voice and firewall features.

  Q. What is the maximum performance DES/3DES/AES-128 IPSec with packages of 1 400 byte for the Cisco 1700 series, 2600, 3600, and 3700 using the VPN Module?

  A. Cisco 2650/51XM with AIM-VPN/BPII or AIM-VPN/BPII-PLUS will give 10 Mbps throughput with traffic IMIX, 22 Mbpsthroughput with the packet size of 1400bytes and support 800 tunnels.

  Q. What is the maximum performance of the IPSec AES-192/256 with IMIX packages for Cisco 1700 series, 2600, 3600, and 3700 using the VPN Module?

  A. Cisco 2650/51XM with AIM-VPN/BPII will give 8.5 Mbit/s throughput with traffic IMIX for AES-192 and 256. BPII-MORE will give around 10 Mbps performance.

  -----------------------------------------

  In addition, you should know that this card was that EOL would be according to:

  http://www.Cisco.com/en/us/products/HW/routers/ps274/prod_eol_notice0900aecd802d3d0b.html

  It is still supported until 2010 and will work well for you, it is simply not fast enough with AES-192 and AES-256 as the version MORE than the same card, which was hardware-optimized especially for large key sizes. If you use 3DES or AES-128, then there is no difference in performance.

• VPN configuration to 150 + branches

  Hi all

  We are planing to have a new research report international 3845 at our headquarters and replace all connections of leased line VPN connections from the service provider. Currently, leased lines are finished in a set of interfaces for E1 3660.

  the service provider is to have a VPN - IP MPLS/BGP, so this will be a peer-2-peer VPN. Since we are a banking institution, we do not want to rely on VPN - L3 service providers.

  My question is, how do we achieve encryption of our new router to all branches and what will be the specific ideal IOS and FRIEND or VPN modules, we should have?

  Thank you

  uddika

  Sorry, I'm confused - you said on the original post

  "my question is, how do we achieve encryption of our new router to all branches and what will be the specific ideal IOS and FRIEND or VPN modules, we should have?"

  But you also said "the service provider is to have a VPN - IP MPLS/BGP, so this will be a peer-2-peer VPN." Since we are a banking institution, we do not want to rely on VPN - L3 service providers. "

  Just so I'm clear - your provider will encrypt the data of your through the MPLS cloud. And you're not happy with this - if you want to make your own encryption and then send it to your service provider? Essentially you want to encrypt him twice - is this correct?

• vpn SSL question

  Hello

  If I change the ip address of the SSL VPN module, re - generate the cert for the new IP address of the SSL VPN module?

  RDG

  That depends on whether your cert has been registered using the FULL domain name or ip address, if the ip address has been used then Yes, you must regenerate, if it was via FQDN and the FULL domain name changed not need him.

• AnyConnect nam - how to hide the vpn components?

  Hello

  for a project we require the use of begging her to nam (eap chaining), but the customer does not want the vpn module is visible.

  the nam module is conditioned by the main anyconnect secure mobility client.

  is their a setting/option to hide the end user vpn dialog boxes?

  Greetings

  Install the anyconnect following basic component:

  msiexec/package anyconnect-win-ver-pre-deploy-k9.msi /norestart PRE_DEPLOY_DISABLE_VPN = 1 /lvx/passive *.

  And the VPN feature will be disabled, and then install NAM

  Starting from here:

  http://www.Cisco.com/en/us/docs/security/vpn_client/AnyConnect/anyconnect30/Administration/Guide/ac02asaconfig.html

• The VPN Client on Fedora FC6 x86_64 compilation error

  When I try to install the VPN Client on FC6, I get the following errors:

  Cisco Systems VPN Client Version 4.8.00 (0490) Linux installer

  ...

  To build the core VPN module, you must have the

  the headers for the kernel for the version of the kernel you are using.

  ...

  Socket module

  make SUBDIRS = /lib/modules/2.6.19-1.2911.6.5.fc6/build modules / space/home/schulze/installquellen/Cisco/vpn/vpnclient - C

  make [1]: Entering directory ' / usr/src/kernels/2.6.19-1.2911.6.5.fc6-x86_64'

  CC [M] /space/home/schulze/installquellen/Cisco/vpn/vpnclient/linuxcniapi.o

  In Datei, eingef? GT von space/home/schulze/installquellen/Cisco/vpn/vpnclient/Cniapi.h:15,

  von /space/home/schulze/installquellen/Cisco/vpn/vpnclient/linuxcniapi.c:27:

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/GenDefs.h:110:2: Warnung: #warning 64 bit

  CC [M] /space/home/schulze/installquellen/Cisco/vpn/vpnclient/frag.o

  In Datei, eingef? GT von space/home/schulze/installquellen/Cisco/vpn/vpnclient/Cniapi.h:15,

  von /space/home/schulze/installquellen/Cisco/vpn/vpnclient/frag.c:16:

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/GenDefs.h:110:2: Warnung: #warning 64 bit

  CC [M] /space/home/schulze/installquellen/Cisco/vpn/vpnclient/IPSecDrvOS_linux.o

  In Datei, eingef? /space/home/Schulze/installquellen/Cisco/VPN/vpnclient/IPSecDrvOS_linux.c:20 von gt:

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/GenDefs.h:110:2: Warnung: #warning 64 bit

  CC [M] /space/home/schulze/installquellen/Cisco/vpn/vpnclient/interceptor.o

  In Datei, eingef? GT von space/home/schulze/installquellen/Cisco/vpn/vpnclient/Cniapi.h:15,

  von /space/home/schulze/installquellen/Cisco/vpn/vpnclient/interceptor.c:30:

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/GenDefs.h:110:2: Warnung: #warning 64 bit

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/interceptor.c: in function? handle_vpnup? :

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/interceptor.c:310: Warnung: Zuweisung von inkompatiblem Zeigertyp

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/interceptor.c:334: Warnung: Zuweisung von inkompatiblem Zeigertyp

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/interceptor.c:335: Warnung: Zuweisung von inkompatiblem Zeigertyp

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/interceptor.c: in function? do_cleanup? :

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/interceptor.c:378: Warnung: Zuweisung von inkompatiblem Zeigertyp

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/interceptor.c: in function? recv_ip_packet_handler? :

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/interceptor.c:553: Fehler:? CHECKSUM_HW? nicht deklariert (erste Benutzung in dieser Funktion)

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/interceptor.c:553: Fehler: (deklarierte Bezeichner only once aufgef wird nicht Jeder? hrt)

  / space/home/schulze/installquellen/Cisco/vpn/vpnclient/interceptor.c:553: Fehler: f? r jede Funktion der er appearance.)

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/interceptor.c:557: Fehler: zu viele argues f? r Funktion? skb_checksum_help?

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/interceptor.c: in function? do_cni_send? :

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/interceptor.c:680: Fehler:? CHECKSUM_HW? nicht deklariert (erste Benutzung in dieser Funktion)

  /Space/home/Schulze/installquellen/Cisco/VPN/vpnclient/interceptor.c:683: Fehler: zu viele argues f? r Funktion? skb_checksum_help?

  make [2]: * [/ space/home/schulze/installquellen/Cisco/vpn/vpnclient/interceptor.o] Fehler 1

  make [1]: * [_module_/space/home/schulze/installquellen/Cisco/vpn/vpnclient] Fehler 2

  make [1]: leaving directory ' / usr/src/kernels/2.6.19-1.2911.6.5.fc6-x86_64'

  make: * [default] Fehler 2

  Has failed to do the module 'cisco_ipsec.ko '.

  Is there advice?

  There could be various reasons for this problem:

  (1) you miss the source package of the kernel, which can be verified by running the command ' rpm - qa | grep kernel ". If it is not installed, please enter your CD or your the Fedora FTP mirror preferred.

  (2) you could be hitting bug CSCsc39924. For which the workaround is as follows

  In the file linuxcniapi.c in the installation package, REPLACE THE LINE (2 occurrences):

  do_gettimeofday (& skb-> stamp);

  WITH THE FOLLOWING LINES:

  #if LINUX_VERSION_CODE > = KERNEL_VERSION (2,6,14)

  {

  struct timeval timestamp;

  do_gettimeofday (?) TAMP);

  skb_set_timestamp (SKB?, TAMP);

  }

  #else

  do_gettimeofday (& skb-> stamp);

  #endif

  AND THEN RERUN the "vpn_install."

  The following links can help you

  http://blog.360.Yahoo.com/blog-.WURHFYwdq8.zfEosWC6j8jQ?p=55

  http://www.Fedoraforum.org/Forum/printthread.php?s=938da17f7e7ac49f82b84e65f8d50596&t=106929&page=5&pp=15

• Cisco 1921: aboard the hw module not used?

  Hello

  I have a 1921 Cisco who has an IPSec connection to the outside, but despite this, it seems that the "Accelerator" hw module is not used because the stats are all zeros (see below). Also, I can see that the module is enabled (using the crypto engine see the brief), but the router connection to the sw module (with the help of see the crypto engine connections flow)

  What could that be caused by?

  See you soon,.

  Sylvain

  gw#show crypto engine accelerator statistic Device:   Onboard VPN Location: Onboard: 0      :Statistics for encryption device since the last clear       of counters 4294967 seconds ago                    0 packets in                           0 packets out                              0 bytes in                             0 bytes out                                0 paks/sec in                          0 paks/sec out                             0 Kbits/sec in                         0 Kbits/sec out                            0 packets decrypted                    0 packets encrypted                        0 bytes before decrypt                 0 bytes encrypted                          0 bytes decrypted                      0 bytes after encrypt                      0 packets decompressed                 0 packets compressed                       0 bytes before decomp                  0 bytes before comp                        0 bytes after decomp                   0 bytes after comp                         0 packets bypass decompr               0 packets bypass compres                    0 bytes bypass decompres               0 bytes bypass compressi                    0 packets not decompress               0 packets not compressed                    0 bytes not decompressed               0 bytes not compressed                    1.0:1 compression ratio                1.0:1 overall           Last 5 minutes:                    0 packets in                           0 packets out                              0 paks/sec in                          0 paks/sec out                             0 bits/sec in                          0 bits/sec out                             0 bytes decrypted                      0 bytes encrypted                          0 Kbits/sec decrypted                  0 Kbits/sec encrypted                     1.0:1 compression ratio                1.0:1 overall gw#show crypto engine brief         crypto engine name:  Virtual Private Network (VPN) Module         crypto engine type:  hardware                      State:  Enabled                   Location:  onboard 0               Product Name:  Onboard-VPN                 HW Version:  1.0                Compression:  Yes                        DES:  Yes                      3 DES:  Yes                    AES CBC:  Yes (128,192,256)                   AES CNTR:  No      Maximum buffer length:  0000           Maximum DH index:  0000           Maximum SA index:  0000         Maximum Flow index:  2000       Maximum RSA key size:  0000         crypto engine name:  Cisco VPN Software Implementation         crypto engine type:  software              serial number:  02FBA4F2        crypto engine state:  installed      crypto engine in slot:  N/A gw#show crypto engine connections flow Crypto engine: Software Crypto Engine       flow_id   ah_conn_id  esp_conn_id     comp_spi           245                 245       0x2F12           246                 246       0x4E13 Crypto engine: Onboard VPN       flow_id   ah_conn_id  esp_conn_id     comp_spi 

  Hey, Sylvain.

  If you are looking for suite-B on hardware support, then you must upgrade to train 15.2 (4) M.

  See the release notes for more details

  http://www.Cisco.com/en/us/docs/iOS/15_2m_and_t/release/notes/15_2m_and_t.PDF

  "IPSec required with Suite B algorithms are now supported by the hardware encryption engine on the.

  Cisco Integrated Services routers generation 2:800 Series, series of 1900, 2901, 2911, 2921, 2935R,

  3925th and 3945TH, which each integrated hardware acceleration of encryption VPN.

  Suite B necessary includes four suites in the user interface of encryption algorithms to use with IKE

  and IPsec, which are described in RFC 6379 and RFC 6380. Each suite consists of a cipher

  algorithm, a digital signature algorithm, an algorithm agree key and a digest of hash or message

  algorithm.

  Suite B provides an improvement in the overall security of Cisco's VPN IPsec, and it allows additional

  Security for large scale deployments. Suite B is the recommended solution for organizations that need

  Advanced security encryption for the wide area network (WAN) between remote sites.

  To get detailed information on the features of Cisco IOS IPsec to 15.2 (4 M) that support the Suite B"

  This should answer your question.

• VPN on Cisco 5520

  Hello

  What are the possibilities that exist for a site to site vpn running in our environment with the following facilities

  Cisco ASA 5520 - running on a multiple context mode

  Cisco 3750 switches

  Microsoft TMG

  In my view, these options are limited in terms of VPN endpoint mode.

  Is there a VPN module we can buy for 5520 run IPSEC VPN?

  ASAs all on Board have a VPN, so there is nothing you have to buy. But you need at least version 9.0 software where the VPN site - to have been introduced to several way of context:

  http://www.Cisco.com/en/us/docs/security/ASA/asa90/release/notes/asarn90.html#wp586890

  VPN remote access are still not supported in multiple context.

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• point to point VPN?

  We have a VPN module with public ip static on one side and Cisco 2620 w / VPN image on the opposite side but without static public ip address. Can we make IPSec VPN connection between both parties? Thank you very much.

  Lateral static will accept someone from generic pre-shared keys and map dynamic crypto. Side Dynamics uses regular card crypto and set the peer of static ip address.

  Lateral static key config is:

  ISAKMP crypto cisco123 key address 0.0.0.0 0.0.0.0

  crypto dynamic-map 10 DYNMAP

  game of transformation-bla

  (may also have cyrpto acl)

  card crypto CMAP 10-isakmp dynamic ipsec DYNMAP

  Look at the config here (ignore the part nat):

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080093f86.shtml