VPN PIX 506e to Linksys RV042?

I'm kind of a rookie of Cisco and need help to set up a virtual private network:

I replaced a Netopia R910 with a Linksys RV042.  I have set the parameters of the best that I could.  I am trying to reconnect the VPN site to site of our network (192.168.0.x private, public xxx.xxx.109.202) to the remote network (xxx.xxx.131.50 192.168.38.x and private, public).

In the Linksys VPN shows connected but no traffic coming.  I can't ping anything on the remote subnet.

It worked fine with the R910 and no settings have changed on the PIX, other new pre-shared keys that match.

Here are the PIX config and the RV042 config is attached as an image.

Thank you very much for your help!

Building configuration...

: Saved

:

PIX Version 6.3(3)

interface ethernet0 auto

interface ethernet1 auto

nameif ethernet0 outside security0

nameif ethernet1 inside security100

enable password ************ encrypted

passwd *************** encrypted

hostname pixfirewall

domain-name ciscopix.com

clock timezone PST -8

clock summer-time PDT recurring

fixup protocol dns maximum-length 512

fixup protocol ftp 21

fixup protocol h323 h225 1720

fixup protocol h323 ras 1718-1719

fixup protocol http 80

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol sip 5060

fixup protocol sip udp 5060

fixup protocol skinny 2000

fixup protocol smtp 25

fixup protocol sqlnet 1521

fixup protocol tftp 69

names

name 192.168.1.0 FirstStreet

name 192.168.38.2 Sco

name xxx.xxx.130.94 FirstWan

name 192.168.4.0 Oakurst

name 192.168.7.0 Clovis

name 192.168.3.0 Madera

name 192.168.0.0 TomJ

name xxx.xxx.131.58 FMLFirst

name xxx.xxx.131.22 Integrity

name 192.168.6.0 TJhome

name 192.168.38.10 Server2

name xxx.xxx.117.182 ClovisPublicIP

name xxx.xxx.100.239 OakurstPublicIP

name xxx.xxx.174.185 MaderaPublicIP

name 192.168.38.64 VideoS1

object-group network FMLRemoteOffices

  description Public IP's and Internal Subnets for All Remote Offices

  network-object OakurstPublicIP 255.255.255.255

  network-object MaderaPublicIP 255.255.255.255

  network-object ClovisPublicIP 255.255.255.255

  network-object xxx.xxx.109.202 255.255.255.255

access-list inside_outbound_nat0_acl permit ip 192.168.38.0 255.255.255.0 Clovis 255.255.255.0

access-list inside_outbound_nat0_acl permit ip 192.168.38.0 255.255.255.0 Oakurst 255.255.255.0

access-list inside_outbound_nat0_acl permit ip 192.168.38.0 255.255.255.0 TJhome 255.255.255.0

access-list inside_outbound_nat0_acl permit ip 192.168.38.0 255.255.255.0 Madera 255.255.255.0

access-list inside_outbound_nat0_acl permit ip any host 192.168.38.248

access-list inside_outbound_nat0_acl permit ip any 192.168.38.248 255.255.255.248

access-list outside_access_in permit tcp any host xxx.xxx.131.54 eq https

access-list outside_access_in permit icmp any any echo-reply

access-list outside_access_in remark Sage e-prescription service 8423

access-list outside_access_in permit tcp any host xxx.xxx.131.54 eq 8423

access-list outside_access_in permit tcp any host xxx.xxx.131.53 eq 1202

access-list outside_access_in permit tcp any host xxx.xxx.131.52 eq 7000

access-list outside_cryptomap_20 permit ip 192.168.38.0 255.255.255.0 Clovis 255.255.255.0

access-list outside_cryptomap_80 permit ip 192.168.38.0 255.255.255.0 Oakurst 255.255.255.0

access-list outside_cryptomap_120 permit ip 192.168.38.0 255.255.255.0 Madera 255.255.255.0

access-list outside_cryptomap_100 permit ip 192.168.38.0 255.255.255.0 TJhome 255.255.255.0

no pager

logging on

icmp permit any echo-reply outside

icmp permit any echo-reply inside

mtu outside 1500

mtu inside 1500

ip address outside xxx.xxx.131.50 255.255.255.248

ip address inside 192.168.38.4 255.255.255.0

ip audit info action alarm

ip audit attack action alarm

ip local pool VPNDHCP 192.168.38.248-192.168.38.252

ip local pool DHCP39 192.168.39.1-192.168.39.254

pdm location Integrity 255.255.255.255 outside

pdm location 192.168.38.0 255.255.255.0 inside

pdm location FirstStreet 255.255.255.0 inside

pdm location FirstStreet 255.255.255.0 outside

pdm location Sco 255.255.255.255 inside

pdm location FirstWan 255.255.255.255 outside

pdm location Oakurst 255.255.255.0 outside

pdm location Clovis 255.255.255.0 outside

pdm location TJhome 255.255.255.0 outside

pdm location Madera 255.255.255.0 outside

pdm location TomJ 255.255.255.0 outside

pdm location 0.0.0.0 255.255.255.255 outside

pdm location xxx.xxx.141.217 255.255.255.255 outside

pdm location 192.168.38.111 255.255.255.255 inside

pdm location 192.168.38.3 255.255.255.255 inside

pdm location FMLFirst 255.255.255.255 outside

pdm location xxx.xxx.130.15 255.255.255.255 outside

pdm location 128.0.0.0 128.0.0.0 outside

pdm location xxx.xxx.109.202 255.255.255.255 outside

pdm location Server2 255.255.255.255 inside

pdm location ClovisPublicIP 255.255.255.255 outside

pdm location OakurstPublicIP 255.255.255.255 outside

pdm location MaderaPublicIP 255.255.255.255 outside

pdm location 192.168.38.248 255.255.255.255 outside

pdm location TomJ 255.255.255.0 inside

pdm location VideoS1 255.255.255.255 inside

pdm location 192.168.38.21 255.255.255.255 inside

pdm group FMLRemoteOffices outside

pdm logging debugging 500

no pdm history enable

arp timeout 14400

global (outside) 1 xxx.xxx.131.51

nat (inside) 0 access-list inside_outbound_nat0_acl

nat (inside) 1 0.0.0.0 0.0.0.0 0 0

static (inside,outside) xxx.xxx.131.54 Server2 netmask 255.255.255.255 0 0

static (inside,outside) xxx.xxx.131.53 192.168.38.21 netmask 255.255.255.255 0 0

static (inside,outside) xxx.xxx.131.52 VideoS1 netmask 255.255.255.255 0 0

access-group outside_access_in in interface outside

route outside 0.0.0.0 0.0.0.0 xxx.xxx.131.49 1

route inside FirstStreet 255.255.255.0 192.168.38.254 1

timeout xlate 3:00:00

timeout conn 4:00:00 half-closed 2:00:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00

timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00

timeout uauth 0:05:00 absolute

aaa-server TACACS+ protocol tacacs+

aaa-server RADIUS protocol radius

aaa-server LOCAL protocol local

aaa authentication ssh console LOCAL

http server enable

http Integrity 255.255.255.255 outside

http xxx.xxx.141.217 255.255.255.255 outside

http xxx.xxx.109.202 255.255.255.255 outside

http 192.168.38.0 255.255.255.0 inside

no snmp-server location

no snmp-server contact

snmp-server community public

no snmp-server enable traps

floodguard enable

sysopt connection permit-ipsec

sysopt connection permit-pptp

crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac

crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac

crypto dynamic-map outside_dyn_map 30 set transform-set ESP-DES-MD5

crypto dynamic-map outside_dyn_map 50 set transform-set ESP-3DES-MD5

crypto map outside_map 20 ipsec-isakmp

crypto map outside_map 20 match address outside_cryptomap_20

crypto map outside_map 20 set peer ClovisPublicIP

crypto map outside_map 20 set transform-set ESP-DES-MD5

crypto map outside_map 80 ipsec-isakmp

crypto map outside_map 80 match address outside_cryptomap_80

crypto map outside_map 80 set peer OakurstPublicIP

crypto map outside_map 80 set transform-set ESP-DES-MD5

crypto map outside_map 100 ipsec-isakmp

crypto map outside_map 100 match address outside_cryptomap_100

crypto map outside_map 100 set peer xxx.xxx.174.234

crypto map outside_map 100 set transform-set ESP-DES-MD5

crypto map outside_map 120 ipsec-isakmp

crypto map outside_map 120 match address outside_cryptomap_120

crypto map outside_map 120 set peer MaderaPublicIP

crypto map outside_map 120 set transform-set ESP-DES-MD5

crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map

crypto map outside_map interface outside

isakmp enable outside

isakmp key ******** address xxx.xxx.141.217 netmask 255.255.255.255 no-xauth no-config-mode

isakmp key ******** address ClovisPublicIP netmask 255.255.255.255 no-xauth no-config-mode

isakmp key ******** address xxx.xxx.64.82 netmask 255.255.255.255 no-xauth no-config-mode

isakmp key ******** address xxx.xxx.67.172 netmask 255.255.255.255 no-xauth no-config-mode

isakmp key ******** address OakurstPublicIP netmask 255.255.255.255 no-xauth no-config-mode

isakmp key ******** address xxx.xxx.24.157 netmask 255.255.255.255 no-xauth no-config-mode

isakmp key ******** address xxx.xxx.174.234 netmask 255.255.255.255 no-xauth no-config-mode

isakmp key ******** address xxx.xxx.88.137 netmask 255.255.255.255

isakmp key ******** address MaderaPublicIP netmask 255.255.255.255 no-xauth no-config-mode

isakmp key ******** address xxx.xxx.109.202 netmask 255.255.255.255 no-xauth no-config-mode

isakmp policy 20 authentication pre-share

isakmp policy 20 encryption des

isakmp policy 20 hash md5

isakmp policy 20 group 2

isakmp policy 20 lifetime 86400

isakmp policy 40 authentication pre-share

isakmp policy 40 encryption 3des

isakmp policy 40 hash md5

isakmp policy 40 group 2

isakmp policy 40 lifetime 86400

vpngroup FMLREASYVPN address-pool VPNDHCP

vpngroup FMLREASYVPN dns-server 192.168.38.3

vpngroup FMLREASYVPN idle-time 1800

vpngroup FMLREASYVPN password ********

vpngroup Brevium address-pool VPNDHCP

vpngroup Brevium dns-server 192.168.38.3

vpngroup Brevium idle-time 1800

vpngroup Brevium password ********

telnet 192.168.38.0 255.255.255.0 inside

telnet TomJ 255.255.255.0 inside

telnet timeout 5

ssh Integrity 255.255.255.255 outside

ssh 99.15.109.202 255.255.255.255 outside

ssh timeout 5

management-access inside

console timeout 0

vpdn group PPTP-VPDN-GROUP accept dialin pptp

vpdn group PPTP-VPDN-GROUP ppp authentication chap

vpdn group PPTP-VPDN-GROUP ppp authentication mschap

vpdn group PPTP-VPDN-GROUP ppp encryption mppe auto

vpdn group PPTP-VPDN-GROUP client configuration address local VPNDHCP

vpdn group PPTP-VPDN-GROUP client configuration dns 192.168.38.3

vpdn group PPTP-VPDN-GROUP pptp echo 60

vpdn group PPTP-VPDN-GROUP client authentication local

vpdn username admin password *********

vpdn username tonette password *********

vpdn username rosie password *********

vpdn username cts password *********

vpdn username MaderaFMLR password *********

vpdn username ruth password *********

vpdn username fogg password *********

vpdn username lanier password *********

vpdn username lanier2 password *********

vpdn username justin password *********

vpdn username mike password *********

vpdn username heather password *********

vpdn username Brevium password *********

vpdn username jeremiah password *********

vpdn enable outside

dhcpd lease 3600

dhcpd ping_timeout 750

dhcpd auto_config outside

username admin password *************** encrypted privilege 15

terminal width 80

Cryptochecksum:******************************

: end

[OK]

NAT exemption, you must add the following:

inside_outbound_nat0_acl ip 192.168.38.0 access list allow TomJ 255.255.255.0 255.255.255.0

Tags: Cisco Security

Similar Questions

  • Site to Site VPN between PIX and Linksys RV042

    I am trying to create a tunnel between a 506th PIX and a Linksys RV042 vpn .  I configured the Phase 1 and Phase 2 as well as the transformation defined and interested traffic and connected to the external interface, but it will not create the tunnel.  Configurations are as follows:

    506th PIX running IOS 6.3

    part of pre authentication ISAKMP policy 40
    ISAKMP policy 40 cryptographic 3des
    ISAKMP policy 40 sha hash
    40 2 ISAKMP policy group
    ISAKMP duration strategy of life 40 86400
    ISAKMP key * address 96.10.xxx.xxx netmask 255.255.255.255
    access-list 101 permit ip 192.168.21.0 255.255.255.0 192.168.1.0 255.255.255.0crypto map Columbia_to_Office 10 ipsec-isakmp
    crypto Columbia_to_Office 10 card matches the address 101
    card crypto Columbia_to_Office 10 set peer 96.10.xxx.xxx
    10 Columbia_to_Office transform-set ESP-3DES-SHA crypto card game
    Columbia_to_Office interface card crypto outside

    Linksys RV042

    Configuration of local groups
    IP only
         IP address: 96.10.xxx.xxx
    Type of local Security group: subnet
    IP address: 192.168.1.0
    Subnet mask: 255.255.255.0

    Configuration of the remote control groups
    IP only
    IP address: 66.192.xxx.xxx
    Security remote control unit Type: subnet
    IP address: 192.168.21.0
    Subnet mask: 255.255.255.0

    IPSec configuration
    Input mode: IKE with preshared key
    Group Diffie-Hellman phase 1: group2
    Phase 1 encryption: 3DES
    Authentication of the phase 1: SHA1
    Life of ITS phase 1: 86400
       
    Phase2 encryption: 3DES
    Phase2 authentication: SHA1
    Phase2 life expectancy: 3600 seconds
    Pre-shared key *.

    I'm a novice on the VPN. Thanks in advance for your expertise.

    Yes, version PIX 6.3 does not support HS running nat or sh run crypto.

    Please please post the complete config if you don't mind.

    Please also try to send traffic between subnets 2 and get the output of:

    See the isa scream his

    See the ipsec scream his

  • PIX 515 to Linksys BEFSX41 VPN

    Hello.

    I searched the forums and the best info I could come up with on this topic, this was one person saying "Eureka, I did it!" and then several hundred "Please send me your config" responses.

    I managed to establish a tunnel between the pix and the Linksys router, and I can ping through the tunnel.

    But nothing else ping seems to go through the tunnel. The access-lists on the pix are not limited on the port, and (for testing), I have the great open linksys firewall. So I don't know where I went wrong.

    I was hoping that this could be a common situation and someone could point me in the right direction to find the solution.

    Thank you!

    In addition,

    Check the order of your ACL. A firewall and a router do not ACL in the same order. Should not discourage you, but I have yet to see a router Linksys do very well a PIX. For some reason the Linksys routers seem to drop packets for unexplained reasons...

  • I need help regarding linksys rv042.

    I have linksys rv042. I want to connect it to the netgear modem.

    Modem will use ppoe and the router will use the static ip address from the ISP.

    I try this scenario but unable to connect to the internet.

    When I connect the modem directly to my pc the internet works

    Or if I use the router as ppoe and modem as bridge it is fine.

    Please help me.

    I agree with gv and suggestion provided by him.

  • PIX & lt; -> user policies VPN PIX and the Windows domain controller

    I've set up a star using IPsec VPN PIX network, all IP traffic is allowed to pass through.

    At the Center, there is a Windows 2003 Small Business Server.

    On remote sites, there is only Windows XP clients used by employees working remotely in the central office.

    Initially, I had a problem of authentication on the server, but I found a document suggesting the Kerberos setting to go to TCP instead of UDP and it solved this issue.

    Now, there is one problem remaining, I can authenticate and access the server resources such as file shares, I can connect to the server Exchange etc. But the client computers do not receive from the server group policies. The error message I am getting in Event Viewer Windows is Userenv id: 1054 - Microsoft suggestion is to check if the DNS works and works DNS, I can locate the DC etc. without problem.

    I tried to make LDAP queries on the server, and again, it works without problem.

    The NetBIOS resolution works very well.

    Basically, everything seems to work expect to get group strategies.

    Does anyone have any suggestions where I should look planned for the solution to this problem?

    Kind regards

    Flovin Olsen

    Here is a vbscript script you must run on every PC has the problem.

    -Cross-section below-

    Dim wshShell

    Set wshShell = WScript.CreateObject ("WScript.Shell")

    prefix = "HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\System\."

    prefix wshShell.regWrite & "GroupPolicyMinTransferRate", 0, "REG_DWORD"

    Prefix2 = "HKEY_CURRENT_USER\Software\Policies\Microsoft\Windows\System\."

    wshShell.regWrite prefix2 & "GroupPolicyMinTransferRate", 0, "REG_DWORD"

    MsgBox "done."

    ---------stop cut -----------------

    Hope this helps

  • NAT Traversal on site to site VPN pix

    I don't think it's possible to implement NAT traversal between a site to IPSEC VPN using ESP tunnels?

    Our ISP to the remote end will provide only a public IP address and which is attributed to their router...

    Sites are using pre-shared keys and IKE

    for example...

    LAN-PIX1-ISPROUTER-INTERNET-ISPPATROUTER-PIX2-LAN

    I have attached the card encryption for more info

    Thanks in advance...

    I guess that NAT - T is most commonly used in a customer VPN environment, but I'm sure that its not limited to this type of connection.

    I just set up a VPN this morning with the help of a customer on a router running 12.2.15T and tested connection with NAT - T works very well by using IP addresses.

    NAT - T enabled by a NAT detection process, and there is that to protect the ESP of a change should work in both environments.

    I'll have a go in my lab, see if I can implement and check it.

    However by going to the original post, you say that only one address is available from the ISP, it is on the router for pix link?

    Where are the limits of NAT, I expect to be in the PIX, but it must be a public IP address on you interfaces also. You can then use the external address as endpoints IPSec, don't need NAT - T in any case.

  • SonicWall VPN PIX - does not, could someone help?

    Hi all

    I'm trying to set up an a 506th PIX VPN tunnel (firmware 6.3 (2)), a firewall SonicWall Pro. It does not at the moment. Phase 1 is ok but the phase 2 is not, the VPN tunnel has not been established, and the security association is removed after a minute or two. I enclose below the PIX config and an attempt to create VPN tunnel debugging output (slightly modified and cut for reasons of confidentiality). The PIX already has other two VPN configured which work perfectly.

    I would be very grateful to anyone who could help me answer the following questions about this VPN configuration:

    1. to debug output, which means the next?

    ISAKMP (0): retransmission of the phase 2 (0/0)... mess_id 0xafc08a94

    crypto_isakmp_process_block:src:remotevpnpeer, dest:vpnpix1 - dpt:500 e0 spt:500

    ISAKMP: error msg not encrypted

    2. in the config, I don't know if the 3 static controls are necessary and how it might interact... What do you think?

    3. in what order things happen in the PIX when traffic is from the local network to remote network by VPN? What is NAT then treatment then setting up VPN to access list? or or treatment, then NAT and VPN to access list? or another possibility?

    4. How can I get it work?

    Thank you very much in advance for any help provided,

    A.G.

    ########### NAMING #################################

    vpnpix1 - is the local cisco PIX

    remotevpnpeer - is the Sonicwall firewall remote

    Intranet - is the local network behind PIX

    remotevpnLAN - is the remote network behind the SonicWall

    ################ CONFIG #############################

    6.3 (2) version PIX

    interface ethernet0 10full

    interface ethernet1 10full

    ethernet0 nameif outside security0

    nameif ethernet1 inside the security100

    .../...

    hostname vpnpix1

    .../...

    names of

    name A.B.C.D vpnpix1-e1

    name X.Y.Z.T vpnpix1-e0

    name E.F.G.H defaultgw

    intranet name 10.0.0.0

    name 192.168.250.0 nat-intranet

    name J.K.L.M internetgw

    name 10.M.N.P server1

    name Server2 10.M.N.Q

    name 10.M.N.R server3

    name 192.168.252.0 remotevpnLAN

    name 10.1.71.0 nat-remotevpnLAN

    .../...

    object-group network server-group

    description servers used by conencted to users remote LAN through a VPN tunnel

    network-host server1 object

    host Server2 network-object

    network-host server3 object

    .../...

    access allowed INCOMING tcp nat-remotevpnLAN 255.255.255.0 list object-group server-eq - ica citrix

    .../...

    OUTBOUND ip intranet 255.0.0.0 allowed access list nat-remotevpnLAN 255.255.255.0

    access list permits INTRANET-to-remotevpnLAN-VPN ip intranet 255.0.0.0 255.255.255.0 remotevpnLAN

    access-list SHEEP, remotevpnLAN permits intranet ip 255.0.0.0 255.255.255.0 nat-remotevpnLAN

    .../...

    IP address outside the vpnpix1-e0 255.255.255.240

    IP address inside the vpnpix1-e1 255.255.252.0

    .../...

    Global 192.168.250.1 1 (outside)

    NAT (inside) 0 access-list SHEEP-to-remotevpnLAN

    NAT (inside) 1 intranet 255.0.0.0 0 0

    .../...

    static (inside, outside) server1 server1 netmask 255.255.255.255 0 0

    public static server2 (indoor, outdoor) server2 netmask 255.255.255.255 0 0

    public static server3 (indoor, outdoor) server3 netmask 255.255.255.255 0 0

    static (exterior, Interior) nat-remotevpnLAN remotevpnLAN netmask 255.255.255.0 0 0

    .../...

    Access-group ENTERING into the interface outside

    Access-group OUTGOING in the interface inside

    Route outside 0.0.0.0 0.0.0.0 internetgw 1

    Route inside the intranet 255.0.0.0 defaultgw 1

    .../...

    Permitted connection ipsec sysopt

    .../...

    Crypto ipsec transform-set esp-3des esp-md5-hmac VPN - TS1

    .../...

    map BusinessPartners 30 ipsec-isakmp crypto

    card crypto BusinessPartners 30 matches the INTRANET-to-remotevpnLAN-VPN address

    card crypto BusinessPartners 30 set peer remotevpnpeer

    card crypto BusinessPartners 30 game of transformation-VPN-TS1

    BusinessPartners outside crypto map interface

    ISAKMP allows outside

    .../...

    ISAKMP key * address remotevpnpeer netmask 255.255.255.255

    ISAKMP identity address

    part of pre authentication ISAKMP policy 10

    ISAKMP policy 10 3des encryption

    ISAKMP policy 10 md5 hash

    10 2 ISAKMP policy group

    ISAKMP life duration strategy 10 28800

    part of pre authentication ISAKMP policy 20

    ISAKMP policy 20 3des encryption

    ISAKMP policy 20 chopping sha

    20 2 ISAKMP policy group

    ISAKMP duration strategy of life 20 28800

    part of pre authentication ISAKMP policy 30

    ISAKMP policy 30 3des encryption

    ISAKMP policy 30 md5 hash

    30 1 ISAKMP policy group

    ISAKMP duration strategy of life 30 28800

    .../...

    : end

    ################## DEBUG ############################

    vpnpix1 # debug crypto isakmp

    vpnpix1 #.

    ISAKMP (0): early changes of Main Mode

    crypto_isakmp_process_block:src:remotevpnpeer, dest:vpnpix1 - dpt:500 e0 spt:500

    Exchange OAK_MM

    ISAKMP (0): treatment ITS payload. Message ID = 0

    ISAKMP (0): audit ISAKMP transform 1 against the policy of priority 10

    ISAKMP: 3DES-CBC encryption

    ISAKMP: MD5 hash

    ISAKMP: default group 2

    ISAKMP: preshared auth

    ISAKMP: type of life in seconds

    ISAKMP: duration of life (basic) of 28800

    ISAKMP (0): atts are acceptable. Next payload is 0

    ISAKMP (0): ITS been pre-shared key, using id ID_IPV4_ADDR type authentication

    to return to the State is IKMP_NO_ERROR

    crypto_isakmp_process_block:src:remotevpnpeer, dest:vpnpix1 - dpt:500 e0 spt:500

    Exchange OAK_MM

    ISAKMP (0): processing KE payload. Message ID = 0

    ISAKMP (0): processing NONCE payload. Message ID = 0

    ISAKMP (0): load useful treatment vendor id

    ISAKMP (0): ID payload

    next payload: 8

    type: 1

    Protocol: 17

    Port: 500

    Length: 8

    ISAKMP (0): the total payload length: 12

    to return to the State is IKMP_NO_ERROR

    crypto_isakmp_process_block:src:remotevpnpeer, dest:vpnpix1 - dpt:500 e0 spt:500

    Exchange OAK_MM

    ISAKMP (0): processing ID payload. Message ID = 0

    ISAKMP (0): HASH payload processing. Message ID = 0

    ISAKMP (0): SA has been authenticated.

    ISAKMP (0): start Quick Mode Exchange, M - ID - 1346336108:afc08a94

    to return to the State is IKMP_NO_ERROR

    ISAKMP (0): send to notify INITIAL_CONTACT

    ISAKMP (0): sending message 24578 NOTIFY 1 protocol

    Peer VPN: ISAKMP: approved new addition: ip:remotevpnpeer / 500 Total VPN peer: 3

    Peer VPN: ISAKMP: Peer ip:remotevpnpeer / 500 Ref cnt incremented: 1 Total VPN peer: 3

    crypto_isakmp_process_block:src:remotevpnpeer, dest:vpnpix1 - dpt:500 e0 spt:500

    ISAKMP (0): processing NOTIFY payload Protocol 14 1

    SPI 0, message ID = 476084314

    to return to the State is IKMP_NO_ERR_NO_TRANS

    ISAKMP (0): retransmission of the phase 2 (0/0)... mess_id 0xafc08a94

    crypto_isakmp_process_block:src:remotevpnpeer, dest:vpnpix1 - dpt:500 e0 spt:500

    ISAKMP: error msg not encrypted

    ISAKMP (0): start Quick Mode Exchange, M - ID 1919346690:7266e802

    crypto_isakmp_process_block:src:remotevpnpeer, dest:vpnpix1 - dpt:500 e0 spt:500

    ISAKMP: error msg not encrypted

    ISAKMP (0): retransmission of the phase 2 (1: 1)... mess_id 0xafc08a94

    crypto_isakmp_process_block:src:remotevpnpeer, dest:vpnpix1 - dpt:500 e0 spt:500

    ISAKMP: error msg not encrypted

    ISAKMP (0): retransmission of the phase 2 (0/2)... mess_id 0x7266e802

    crypto_isakmp_process_block:src:remotevpnpeer, dest:vpnpix1 - dpt:500 e0 spt:500

    ISAKMP: error msg not encrypted

    ISAKMP (0): retransmission of the phase 2 (2/3)... mess_id 0xafc08a94

    crypto_isakmp_process_block:src:remotevpnpeer, dest:vpnpix1 - dpt:500 e0 spt:500

    ISAKMP: error msg not encrypted

    ISAKMP (0): retransmission of the phase 2 (1/4)... mess_id 0x7266e802

    crypto_isakmp_process_block:src:remotevpnpeer, dest:vpnpix1 - dpt:500 e0 spt:500

    ISAKMP: error msg not encrypted

    ISAKMP (0): start Quick Mode Exchange, M - ID - 1475513565:a80d7323

    ISAKMP (0): delete SA: CBC vpnpix1-e0, dst remotevpnpeer

    crypto_isakmp_process_block:src:remotevpnpeer, dest:vpnpix1 - dpt:500 e0 spt:500

    ISAKMP: drop msg deleted his

    ISADB: Reaper checking HIS 0x10ff1ac, id_conn = 0 DELETE IT!

    Peer VPN: ISAKMP: Peer ip:remotevpnpeer / 500 Ref cnt decremented for: 0 Total of VPN peer: 3

    Peer VPN: ISAKMP: deleted peer: ip:remotevpnpeer / 500 Total VPN peers: 2

    ISADB: Reaper checking HIS 0 x 1100984, id_conn = 0

    ISADB: Reaper checking HIS 0x10fcddc, id_conn = 0

    crypto_isakmp_process_block:src:remotevpnpeer, dest:vpnpix1 - dpt:500 e0 spt:500

    ISAKMP: its not located for ike msg

    #####################################################

    Get rid of:

    static (exterior, Interior) nat-remotevpnLAN remotevpnLAN netmask 255.255.255.0 0 0

    You don't need it. Change:

    OUTBOUND ip intranet 255.0.0.0 allowed access list nat-remotevpnLAN 255.255.255.0

    access-list SHEEP, remotevpnLAN permits intranet ip 255.0.0.0 255.255.255.0 nat-remotevpnLAN

    TO:

    access list permits OUTGOING ip intranet 255.0.0.0 255.255.255.0 remotevpnLAN

    access-list SHEEP, remotevpnLAN permits intranet ip 255.0.0.0 255.255.255.0 remotevpnLAN

    This indicates the PIX not NAT IPSec traffic. NAT happens BEFORE IPSec in the PIX, so if you the traffic IPSec nat it will never match your crypto access list and will not be encrypted.

    This, however, should not stop the tunnel of Phase 2 of the course of construction, they would stop flowing above the tunnel, traffic, so you still have a problem somewhere. What I'm guessing, is that the Sonicwall (SW) has a different encryption-defined list access, it must be the EXACT OPPOSITE of what is configured on the PIX. In other words, the SW should be encrypting the traffic of "remotevpnLAN-24" "intranet/8", make sure that the subnet mask ar ETHE same too. "

    To answer your questions:

    1. it simply means that the PIX has not received a response and is to retransmit the last ISAKMP packet. The process_block simply means that the PIX has dropped a package that was to be encrypted because the IPSec tunnel has not been built. If you get the tunnel built, these messages will disappear.

    2. the 3 first static does not appear to be linked to the tunnel IPSec, if they are simply to access a server inside, then they will not affect this VPN tunnel. The last of them should be deleted, as I already said.

    3. for traffic initiated from inside the PIX, the order is incoming ACL, then NAT, IPSec processing. That's why your OUTGOING ACL must allow traffic first, then your NAT 0 statement refuses to be NAT had, then the encryption function is the traffic and the number.

    4 do what I said above :-)

    If you still have no luck, re - run debugs, but initiate traffic behind the Sonicwall, in this way the Sonicwall will try and debug of build that the tunnel and you will get more information on the PIX. Mainly, we'll see what traffic model the SonicWall is configured to encrypt (you don't see if the PIX initiates the tunnel).

  • Allows you to control access VPN PIX

    I have a situation. I want to use Cisco PIX to create 2 VPN tunnels: called "admingroup"(subnet 192.168.10.X) for full access and another called "vendorgroup"(subnet 192.168.11.X) for limited access (only www access to 192.168.1.100). "" "" Admin and the seller will use Cisco for XP vpn clients. But for some reason, the admin and vendor access even. I think I may need to remove the command "sysopt", currently I use admingroup to PIX of remote connection,

    1. can I remove "sysopt" remote control while I vpn in PIX?

    2. why the admin and the seller have equal access?

    Here are the PIX config in a short version:

    permit 192.168.1.0 ip access list nat_acl 255.255.255.0 any

    access-list 101 permit ip 192.168.7.0 255.255.255.0 192.168.10.0 255.255.255.0

    access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.10.0 255.255.255.0

    access-list 101 permit ip 192.168.7.0 255.255.255.0 192.168.11.0 255.255.255.0

    access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.11.0 255.255.255.0

    out_acl list of access allowed tcp 192.168.11.0 255.255.255.0 host 192.168.1.100 eq www

    permit ip 192.168.10.0 access list out_acl 255.255.255.0 any

    IP address outside pppoe setroute

    IP address inside 192.168.7.253 255.255.255.0

    IP verify reverse path to the outside interface

    IP verify reverse path inside interface

    IP local pool adminpool 192.168.10.1 - 192.168.10.7

    IP local pool vendorpool 192.168.11.1 - 192.168.11.7

    Global 1 60.1.1.10 (outside)

    (Inside) NAT 0-list of access 101

    NAT (inside) 1 access-list nat_acl 0 0

    Access-group out_acl in interface outside

    Route inside 192.168.1.0 255.255.255.0 192.168.7.254 1

    Permitted connection ipsec sysopt

    Crypto ipsec transform-set RIGHT aes - esp esp-md5-hmac

    Crypto-map dynamic dynmap 10 transform-set RIGHT

    map mymap 10-isakmp ipsec crypto dynamic dynmap

    mymap outside crypto map interface

    ISAKMP allows outside

    ISAKMP identity address

    part of pre authentication ISAKMP policy 10

    ISAKMP policy 10 aes encryption

    ISAKMP policy 10 md5 hash

    10 2 ISAKMP policy group

    ISAKMP life duration strategy 10 86400

    vpngroup admingroup address adminpool pool

    vpngroup dns-server 192.168.1.3 admingroup

    vpngroup admingroup by default-field test.com

    vpngroup admingroup split tunnel 101

    vpngroup idle time 1800 admingroup

    admingroup vpngroup password *.

    vpngroup address vendorpool pool vendorgroup

    vpngroup dns 192.168.1.3 Server vendorgroup

    vpngroup vendorgroup by default-field test.com

    vpngroup split tunnel 101 vendorgroup

    vpngroup idle 1800 vendorgroup-time

    vpngroup password vendorgroup *.

    VPDN group pppoex request dialout pppoe

    A little luck?

  • Problems with VPN PIX 525 Lan-to-Lan Cisco 2610XM

    Hello world

    I have a VPN with PIX 525 versi problems? n 7.2 (1) and Cisco 2610XM Version 12.3 (18). When start the PIX, all tunnels works well, but 6-7 days, some of the tunnels do not work properly. Traffic passes the tunnel with some networks, but not with all networks. Sometimes the tunnel descends and it is imposible to go upward.

    Attach them files are the "debug crypto isakmp" in both devices.

    Thank you and sorry for my bad English

    If your configuration of the tunnel on router 7500 series, the tunnel interface are not supported for politicians to service in the tunnel interfaces on 7500

  • PAT on IPSEC VPN (Pix 501)

    Hello

    I work to connect a PIX 501 VPN for a 3rd party hub 3015. The hub requires all traffic to come from a single source IP address. This IP address is assigned to me as z.z.z.z. I have successfully built the VPN and tested by mapping staticly internal IP with the IP address assigned, but cannot get the orders right to do with PAT in order to have more than one computer on the subnet 10.x.x.0. This Pix is also a backup for internet routing and NAT work currently as well for this.

    I can redirect traffic to my subnet to the remote subnet via the VPN, but I can't seem to get the right stuff PAT to the VPN using the assigned IP address. If anyone can give me some advice that would be great.

    lines of current config interesting configuration with static mapping:

    --------------------------------------------------------------------------

    access-list 101 permit ip 10.0.0.0 255.255.255.0 y.y.y.0 255.255.255.0

    access-list 102 permit ip y.y.y.0 255.255.255.0 z.z.z.z host

    access-list 103 allow host ip y.y.y.0 255.255.255.0 z.z.z.z

    IP address outside w.w.w.1 255.255.255.248

    IP address inside 10.0.0.1 255.255.255.0

    Global 1 interface (outside)

    NAT (inside) - 0 102 access list

    NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

    public static z.z.z.z (Interior, exterior) 10.x.x.50 netmask 255.255.255.255 0 0

    Route outside 0.0.0.0 0.0.0.0 w.w.w.2 1

    correspondence address card crypto mymap 10 103

    mymap outside crypto map interface

    ISAKMP allows outside

    Thank you!

    Dave

    Dave,

    (1) get rid of static electricity. Use more Global/NAT. The static method will create a permanent

    translation for your guests inside and they will always be this way natted. Use

    NAT of politics, on the contrary, as shown here:

    not static (inside, outside) z.z.z.z 10.x.x.50 netmask 255.255.255.255 0 0

    Global (outside) 2 z.z.z.z netmask 255.255.255.255

    (Inside) NAT 2-list of access 101

    (2) the statement, "nat (inside) access 0 2' list will prevent nat of your valuable traffic."

    Delete this because you need to nat 2 nat/global card. (as a general rule, simply you

    If you terminate VPN clients on your device and do not want inside the traffic which

    is intended for the vpn clients to be natted on the external interface).

    (3) with the instructions of Global/nat 2, all traffic destined for the remote network will be first

    translated into z.z.z.z. Then your card crypto using the ACL 103 will encrypt all traffic which

    sources of z.z.z.z for y.y.y.0 24. This translation wil happen only when traffic is destined for the vpn.

    I hope this helps. I have this work on many tunnels as you describe.

    Jamison

  • Several Interfaces of VPN - Pix 6.3 (5)

    Hi all

    I'm trying to establish a secondary VPN interface off our PIX for reasons of split tunneling. Unfortunately, I can't upgrade to 7.0 + to provide the functionality of routing same interface.

    I want to keep our card crypto in place current production until the transition is complete. Is it possible to have a 'map outside_map interface outside crypto' and a 'card crypto interface ExternalVPN ExternalVPN' or will be the new command to destroy the existing?

    Thank you.

    -Dominique

    This version of Pix follows the same principle that any 7.x or 8.x or cisco devices, there can only be one card encryption interface, in your case, I think you are applying cryptographic cards various different interfaces so the substitution them shouldn't be your concerned, rather ensuring the flow and routing.

  • Remote access VPN pix version 8.0 (3)

    Hi all

    First of all, I would like to thank to all members of the forum who got help in several messages on the configuration of the pix 515.

    I am now configuring remote VPN access with radius authentication to my network, but I can't connect.

    I use the cisco vpn client 5.0.03.0560, I have also tested my pix radius (inside) server authentication and works very well.

    I already tried to retype the key of the cli, but I still can't remote access vpn to work.

    I also tried to create another remote vpn with another name and local authentication, but I have the same problem.

    I use 8.0 (3) version pix.

    Can someone help me

    I attach the log file of the cisco vpn client to help solve the problem, as well a configuration of the pix folder.

    Thank you very much in advance and I seek prior information.

    http://www.Cisco.com/en/us/docs/security/ASA/asa72/configuration/guide/vpnadd.html#wp999516

    [Pls RATE if HELP]

  • MS CA VPN PIX (NO_PROPOSAL_CHOSEN)

    I use stand-alone MS Server CA to issue certificates, I have already installed the CEP add-on on Windows and there is connecvity between Pix and MS CA.

    -cert ca exit - sh

    CA

    Status: available

    Serial number of the certificate: 02c50c2f5832d9964ef6eb5f4ea988d6

    Use keys: Signature

    CN = jeff-pc

    OU = company

    O = Company

    L = SP

    ST = SP

    C = BR

    EA =<16> [email protected] / * /

    Validity date:

    start date: 09:43:12 BRST November 4, 2003

    ------------------

    I have already registered a VPN client with a certificate from this CA MS according to http://www.cisco.com/en/US/tech/tk583/tk372/technologies_tech_note09186a008009468a.shtml documentation, very usable...

    But whenever I try to establish a VPN between the VPN Client and VPN(rsa-sig) Pix, the IKE negotiation does not... with message (NOTIFY: NO_PROPOSAL_CHOSEN) on the Client VPN Log Viewer

    Vpn configuration-

    Crypto ipsec transform-set esp - esp-md5-hmac certset

    Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

    Crypto-map dynamic dynmap 10 transform-set RIGHT

    map mymap 10-isakmp ipsec crypto dynamic dynmap

    client authentication card crypto LOCAL mymap

    mymap outside crypto map interface

    ISAKMP allows outside

    ISAKMP identity address

    ISAKMP policy 10 authentication rsa - sig

    encryption of ISAKMP policy 10

    ISAKMP policy 10 md5 hash

    10 1 ISAKMP policy group

    ISAKMP life duration strategy 10 86400

    vpngroup address ippool2 pool vpncert

    vpngroup idle 1800 vpncert-time

    vpngroup password vpncert *.

    CA identity pc-jeff 10.10.10.230:/certsrv/mscep/mscep.dll

    CA set up pc-jeff 1 5 crloptional ra

    -------------------------------

    OBS: before the VPN works very well.

    I appreciate who can help me in this problem...

    Jefferson

    create a separate policy using Group 2, the client software cannot use Group1

    i.e.

    ISAKMP identity address

    You may need to change this on isakmp identity hostname '

    ISAKMP policy 10 authentication rsa - sig

    encryption of ISAKMP policy 10

    ISAKMP policy 10 md5 hash

    10 1 ISAKMP policy group

    ISAKMP life duration strategy 10 86400

    ISAKMP policy 20 authentication rsa - sig

    encryption of ISAKMP policy 20

    ISAKMP policy 20 chopping sha

    20 2 ISAKMP policy group

    ISAKMP duration strategy of life 20 86400

    Try this first, there may be a problem using "isakmp identity address" rather than "isakmp identity hostname.

    I have information on my website about the configuration of Microsoft SCEP CA and Cisco routers that you might

    http://www.geocities.com/dgarnett2002/infoarch.html

  • Pix VPN PIX

    I tried using Cisco for the creation of a vpn site to site, located at http://www.cisco.com/warp/public/110/38.html.

    However, for some reason, this isn't working and I don't know where to start looking.

    I have attached the configs and see the crypto... results.

    It's about a delay, to help or management, you can provide would be greatly appreciated!

    1 delete the lines of password of your config - the encryption used by pixen on passwords is low

    2. I would like to clean the access lists. You seem to be reusing existing lists (with tcp pix2 lines and mirror on pix entries 1 - IE, 10.10.0.0/16 does not exist in both places)

    3. your results don't watch any attempt - do you have hosts on each end of the tunnel you can try ping? That is to say, of 10.36.1.5 ping 10.10.0.2. This ping attempts should increment counters to show crypto ipsec sa - either with success or failure

  • Internet access without split tunneling VPN PIX

    I have a PIX 515E with code 6.31. I installed a VPN to allow access to the internal network from the Internet using the Cisco VPN client. It does not work properly. We have some sellers who demand that we come from our Internet IP range to allow us access to their database on the Internet. This works very well for our internal users, but I will allow users VPN for this also.

    Is there a way to allow the user from the VPN client to use the Internet for business access to the internet instead of use the split tunneling to access the internet through their own connection? I would like users to vpn to be NAT would have réécrirait Internet and seeming come from our pool of Internet addresses. What I found references by using the split tunneling, but this won't work for me. Am I stuck getting a VPN concentrator to achieve?

    Thank you

    Josh

    [email protected] / * /.

    The PIX cannot route a package back on the same interface, he entered the, which includes a customer entering the interface external and routed VPN package back on the same interface.

    A router or a VPN concentrator would be able to do this, but not a PIX, sorry.

Maybe you are looking for

  • error code 0165

    I constantly receive 0165 error code when starting the service of 4 k with the connected player. Nothing in the instructions on the net. Internet connections and HDMI are OK

  • HP z800 suddenly become 33% faster at rendering

    I have 3 desktops z800 identical with x 5650 processors in my cluster of calculation used for animations and rendering of images. Recently, I had some problems trying to boot remotely and took the ram and reinstalled it to try to resolve an error whi

  • Defender window stopped giving a code of error 0x800106ba

    I installed microsoft essential for definition update security but windows defender on my PC is off giving an error 0x800106ba code. Now, no update is installed. How to activate the defender of the window again.

  • Enable or disable Windows features: most of them is unchecked.

    original title: Turn Windows features or not: just stumbled on this feature when uninstalling a program and noticed that most of them is unchecked. What would constitute the "standard/default" installed in windows for a Dell Inspiron 64 programs.   I

  • Msvcr71.dll missing or can not very well in the errior

    I get this when I want to connect to remote CCTV cameras, can someone help me fix this problem? I am running windows7 64-bit. Thank you